Temat: Chętny z Huawei HG553/HG556 potrzebny
Czy ktoś ma wolny Huawei HG553/HG556 i chciałby testować soft?
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Zaloguj się lub zarejestruj by napisać odpowiedź
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
Chętny z Huawei HG553/HG556 potrzebny (Strona 1 z 3)
eko.one.pl → Oprogramowanie / Software → Chętny z Huawei HG553/HG556 potrzebny
Posty: 1 do 25 z 72
Odp: Chętny z Huawei HG553/HG556 potrzebny
mam 
próbowałem obu obrazów bb, bb+luci
niestety router nie wstaje, miga dioda power, później świeci ciągle i druga obok świeci czasami mrugnie
brak połączenia, nie działa dhcp, ustawieni na sztywno nic nie daje
Odp: Chętny z Huawei HG553/HG556 potrzebny
A sprawdź obraz z openwrt.org
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
4 2015-01-19 23:00:06 (edytowany przez marcel_ms 2015-01-19 23:28:13)
Odp: Chętny z Huawei HG553/HG556 potrzebny
na "oryginalny" obraz dlink wgrałem twoje bb+luci nie ruszyło, cokolwiek wgrywałem dalej(twoje bb, openwrt.org) nie chciało działać, dopiero ponowne wgranie obrazu dlink a następnie openwrt.org zadziałało
Odp: Chętny z Huawei HG553/HG556 potrzebny
To już dziwne zaczyna się robić.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
wgrałem też twoj z poziomu wgranego openwrt.org i też nie ruszył
Odp: Chętny z Huawei HG553/HG556 potrzebny
Jeszcze raz: obraz z openwrt.org w końcu działa?
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
tak obraz z openwrt.org wgrany na fabryczny dziala
Odp: Chętny z Huawei HG553/HG556 potrzebny
Jakiego urządzenia używasz?
PS - i czasami czy nie masz kabla podłączonego pod port lan1?
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
10 2015-01-20 09:27:17 (edytowany przez marcel_ms 2015-01-20 09:29:02)
Odp: Chętny z Huawei HG553/HG556 potrzebny
hg553
głowy nie dam, chyba sprawdzałem też na innych
w czym rzecz z tym lan1? już doczytałem
tak jest tylko w twoim obrazie?
Odp: Chętny z Huawei HG553/HG556 potrzebny
W moim lan1 jest domyślnie wanem, tak.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
podsumowanie
firmware oryginalne -> openwrt.org OK -> twoje luci nie działa
następnie cokolwiek bym nie wgrywał nie działa muszę wrzucić oryginał
firmware oryginalne -> twoje luci nie działa
powrót przez oryginał
13 2015-01-20 18:44:58 (edytowany przez Cezary 2015-01-20 19:15:33)
Odp: Chętny z Huawei HG553/HG556 potrzebny
Czy masz kabel szeregowy żeby stwierdzić co "nie działa"?
PS. Podmieniłem plik, tym razem bez podziału switcha - jest tak jak openwrt daje. Wgraj i zobacz.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
udało się, można się połączyć z ruterem, działa luci
w logach było coś o systemie plików jffs i niewłaściwej wersji kernela po restarcie już tego nie było
czy to jest wersja tylko do testów/okrojona ? nie działa usb ....
Odp: Chętny z Huawei HG553/HG556 potrzebny
Co to znaczy "nie działa usb"? Pełnymi zdaniami pisz...
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
po podłączeniu pendrive'a brak informacji w logach i dmesg
root@OpenWrt:~# cat /proc/bus/usb/devices
cat: can't open '/proc/bus/usb/devices': No such file or directoryOdp: Chętny z Huawei HG553/HG556 potrzebny
Przecież to BB jest. Masz zrobić cat /sys/kernel/debug/usb/devices a nie /proc...
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
root@OpenWrt:~# cat /sys/kernel/debug/usb/devices
cat: can't open '/sys/kernel/debug/usb/devices': No such file or directorynie ma zainstalowanych żadnych pakietów z "usb" w nazwie
Odp: Chętny z Huawei HG553/HG556 potrzebny
Pokaż wyniki poleceń
cat /rom/etc/banner
ls /lib/modules/3.10.49/*
opkg list_installed | grep usb
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
root@OpenWrt:~# cat /rom/etc/banner
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (14.07, r42625)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:~# ls /lib/modules/3.10.49/*
/lib/modules/3.10.49/arc4.ko
/lib/modules/3.10.49/b43.ko
/lib/modules/3.10.49/bcma.ko
/lib/modules/3.10.49/button-hotplug.ko
/lib/modules/3.10.49/cdc_ether.ko
/lib/modules/3.10.49/cfg80211.ko
/lib/modules/3.10.49/compat.ko
/lib/modules/3.10.49/crc-ccitt.ko
/lib/modules/3.10.49/crypto_blkcipher.ko
/lib/modules/3.10.49/ehci-hcd.ko
/lib/modules/3.10.49/ehci-platform.ko
/lib/modules/3.10.49/gpio_keys_polled.ko
/lib/modules/3.10.49/input-core.ko
/lib/modules/3.10.49/input-polldev.ko
/lib/modules/3.10.49/ip6_tables.ko
/lib/modules/3.10.49/ip6t_REJECT.ko
/lib/modules/3.10.49/ip6table_filter.ko
/lib/modules/3.10.49/ip6table_mangle.ko
/lib/modules/3.10.49/ip6table_raw.ko
/lib/modules/3.10.49/ip_tables.ko
/lib/modules/3.10.49/ipt_MASQUERADE.ko
/lib/modules/3.10.49/ipt_REJECT.ko
/lib/modules/3.10.49/iptable_filter.ko
/lib/modules/3.10.49/iptable_mangle.ko
/lib/modules/3.10.49/iptable_nat.ko
/lib/modules/3.10.49/iptable_raw.ko
/lib/modules/3.10.49/ipv6.ko
/lib/modules/3.10.49/mac80211.ko
/lib/modules/3.10.49/nf_conntrack.ko
/lib/modules/3.10.49/nf_conntrack_ftp.ko
/lib/modules/3.10.49/nf_conntrack_ipv4.ko
/lib/modules/3.10.49/nf_conntrack_ipv6.ko
/lib/modules/3.10.49/nf_conntrack_irc.ko
/lib/modules/3.10.49/nf_defrag_ipv4.ko
/lib/modules/3.10.49/nf_defrag_ipv6.ko
/lib/modules/3.10.49/nf_nat.ko
/lib/modules/3.10.49/nf_nat_ftp.ko
/lib/modules/3.10.49/nf_nat_ipv4.ko
/lib/modules/3.10.49/nf_nat_irc.ko
/lib/modules/3.10.49/nls_base.ko
/lib/modules/3.10.49/ppp_async.ko
/lib/modules/3.10.49/ppp_generic.ko
/lib/modules/3.10.49/pppoe.ko
/lib/modules/3.10.49/pppox.ko
/lib/modules/3.10.49/slhc.ko
/lib/modules/3.10.49/usb-common.ko
/lib/modules/3.10.49/usbcore.ko
/lib/modules/3.10.49/usbnet.ko
/lib/modules/3.10.49/x_tables.ko
/lib/modules/3.10.49/xt_CT.ko
/lib/modules/3.10.49/xt_LOG.ko
/lib/modules/3.10.49/xt_REDIRECT.ko
/lib/modules/3.10.49/xt_TCPMSS.ko
/lib/modules/3.10.49/xt_comment.ko
/lib/modules/3.10.49/xt_conntrack.ko
/lib/modules/3.10.49/xt_id.ko
/lib/modules/3.10.49/xt_limit.ko
/lib/modules/3.10.49/xt_mac.ko
/lib/modules/3.10.49/xt_mark.ko
/lib/modules/3.10.49/xt_multiport.ko
/lib/modules/3.10.49/xt_nat.ko
/lib/modules/3.10.49/xt_state.ko
/lib/modules/3.10.49/xt_tcpudp.ko
/lib/modules/3.10.49/xt_time.ko
root@OpenWrt:~# opkg list_installed | grep usb
kmod-usb-core - 3.10.49-1
kmod-usb-net - 3.10.49-1
kmod-usb-net-cdc-ether - 3.10.49-1
kmod-usb2 - 3.10.49-1zdążyłem zainstalować kmod-usb-core kmod-usb2 kmod-usb-net-cdc-ether
dmesg
po pierwszym uruchomieniu wyświetlało coś takiego
Linux version 3.10.49 (cezary@eko.one.pl)
a teraz mam
Linux version 3.10.49 (bb@builder1)
Odp: Chętny z Huawei HG553/HG556 potrzebny
Właśnie. To nie jest moje firmware, teraz masz oryginał z openwrt.org, nie mój.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
coś nie tak się wgrało na tym samym obrazie raz miałem cezary@.... a poźniej bb@...
czy to możliwe że wgrywajac poprzez "OEM easy installation" obraz nie wgrał się prawidłowo?
teraz zrobiłem to z poziomu luci
i jest tak
Using username "root".
root@192.168.1.1's password:
BusyBox v1.22.1 (2015-01-15 19:39:18 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_ _____ _____
| | / ____|_ _|
| | _ _| | | |
| | | | | | | | |
| |___| |_| | |____ _| |_
|______\__,_|\_____|_____|
----------------------------------------------------------------
| |
| OpenWrt Barrier Breaker (r44065) |
| Build time: 2015-01-20 19:09 CET |
| |
| Cezary Jackiewicz (obsy), http://eko.one.pl |
| |
----------------------------------------------------------------
| Machine: Unknown |
| Uptime: 0d, 00:02:37 |
| Load: 1.29 0.79 0.31 |
| Flash: total: 9.5MB, free: 9.0MB, used: 6% |
| Memory: total: 60.0MB, free: 46.7MB, used: 22% |
| WAN: |
| LAN: 192.168.1.1 |
----------------------------------------------------------------
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.10.49 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #3 Tue Jan 20 19:13:43 CET 2015
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: d080.5003
[ 0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected 33303133, got 20a994c2)
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board: board name: HW553
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 8031ec60, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 61144k/65536k available (2503k kernel code, 4392k reserved, 731k data, 284k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.036000] Calibrating delay loop... 297.98 BogoMIPS (lpj=595968)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.064000] registering PCI controller with io_map_base unset
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x8007fff]
[ 0.108000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.112000] pci 0000:00:01.0: [14e4:4318] type 00 class 0x028000
[ 0.112000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00001fff]
[ 0.124000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.124000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30001fff]
[ 0.128000] PCI host bridge to bus 0000:01
[ 0.132000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff]
[ 0.136000] pci_bus 0000:01: root bus resource [io 0x8008000-0x800ffff]
[ 0.140000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.144000] pci 0000:01:1e.0: [14e4:6358] type 02 class 0x060700
[ 0.144000] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.148000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05
[ 0.148000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 05
[ 0.148000] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff]
[ 0.152000] pci 0000:01:1e.0: BAR 7: assigned [io 0x8008000-0x80080ff]
[ 0.156000] pci 0000:01:1e.0: BAR 8: assigned [io 0x8008400-0x80084ff]
[ 0.160000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05]
[ 0.164000] pci 0000:01:1e.0: bridge window [io 0x8008000-0x80080ff]
[ 0.168000] pci 0000:01:1e.0: bridge window [io 0x8008400-0x80084ff]
[ 0.172000] pci 0000:01:1e.0: bridge window [mem 0x38000000-0x3fffffff]
[ 0.176000] PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
[ 0.180000] pci 0000:01:1e.0: setting latency timer to 64
[ 0.180000] Switching to clocksource MIPS
[ 0.192000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 0.200000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64
[ 0.220000] ssb: Found chip with id 0x4318, rev 0x02 and package 0x00
[ 0.228000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
[ 0.228000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
[ 0.228000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
[ 0.228000] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
[ 0.268000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.276000] NET: Registered protocol family 2
[ 0.284000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.292000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.296000] TCP: Hash tables configured (established 512 bind 512)
[ 0.304000] TCP: reno registered
[ 0.308000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.312000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.320000] NET: Registered protocol family 1
[ 0.324000] PCI: CLS 0 bytes, default 16
[ 0.332000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.336000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.348000] msgmni has been set to 119
[ 0.352000] io scheduler noop registered
[ 0.356000] io scheduler deadline registered (default)
[ 0.368000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.376000] console [ttyS0] enabled, bootconsole disabled
[ 0.392000] physmap platform flash device: 02000000 at 1e000000
[ 0.396000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[ 0.408000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[ 0.408000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.412000] Amd/Fujitsu Extended Query version 1.3.
[ 0.420000] number of CFI chips: 1
[ 0.424000] bcm63xxpart: CFE boot tag found with version 7 and board type HW553
[ 0.432000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.436000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[ 0.444000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length ea0000
[ 0.452000] bcm63xxpart: Partition 3 is nvram offset fe0000 and length 20000
[ 0.460000] bcm63xxpart: Partition 4 is linux offset 20000 and length fc0000
[ 0.468000] bcm63xxpart: Spare partition is offset 660004 and length 97fffc
[ 0.472000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.480000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.488000] 0x000000000000-0x000000020000 : "CFE"
[ 0.496000] 0x000000020100-0x000000140000 : "kernel"
[ 0.500000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.516000] 0x000000140000-0x000000fe0000 : "rootfs"
[ 0.528000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.532000] mtd: partition "rootfs_data" created automatically, ofs=0x660000, len=0x980000
[ 0.540000] 0x000000660000-0x000000fe0000 : "rootfs_data"
[ 0.552000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.560000] 0x000000020000-0x000000fe0000 : "linux"
[ 0.572000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
[ 0.592000] libphy: bcm63xx_enet MII bus: probed
[ 0.600000] b53_common: found switch: BCM5325, rev 0
[ 0.604000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Broadcom B53 (1)]
[ 0.620000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.636000] TCP: cubic registered
[ 0.640000] NET: Registered protocol family 17
[ 0.644000] Bridge firewalling registered
[ 0.648000] 8021q: 802.1Q VLAN Support v1.8
[ 0.656000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 0.672000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.684000] Freeing unused kernel memory: 284K (80339000 - 80380000)
[ 5.576000] usbcore: registered new interface driver usbfs
[ 5.580000] usbcore: registered new interface driver hub
[ 5.588000] usbcore: registered new device driver usb
[ 5.604000] Button Hotplug driver version 0.4.1
[ 5.704000] SCSI subsystem initialized
[ 5.724000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.732000] ehci-platform: EHCI generic platform driver
[ 5.740000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.744000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.756000] ehci-platform ehci-platform: irq 18, io mem 0xfffe1300
[ 5.772000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 5.780000] hub 1-0:1.0: USB hub found
[ 5.784000] hub 1-0:1.0: 2 ports detected
[ 5.796000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.804000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[ 5.808000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 5.820000] ohci-platform ohci-platform: irq 13, io mem 0xfffe1400
[ 5.884000] hub 2-0:1.0: USB hub found
[ 5.888000] hub 2-0:1.0: 2 ports detected
[ 5.908000] usbcore: registered new interface driver usb-storage
[ 5.916000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 6.836000] usb 1-2: new high-speed USB device number 2 using ehci-platform
[ 7.232000] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 7.252000] scsi0 : usb-storage 1-2:1.0
[ 8.344000] scsi 0:0:0:0: Direct-Access TOSHIBA TransMemory PMAP PQ: 0 ANSI: 4
[ 9.256000] eth0: link UP - 100/full - flow control off
[ 9.764000] sd 0:0:0:0: [sda] 15240576 512-byte logical blocks: (7.80 GB/7.26 GiB)
[ 9.772000] sd 0:0:0:0: [sda] Write Protect is off
[ 9.780000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 9.780000] sd 0:0:0:0: [sda] No Caching mode page found
[ 9.784000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.800000] sd 0:0:0:0: [sda] No Caching mode page found
[ 9.804000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.832000] sda: sda1
[ 9.844000] sd 0:0:0:0: [sda] No Caching mode page found
[ 9.848000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.856000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 11.080000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 12.452000] eth0: link DOWN
[ 19.752000] NET: Registered protocol family 10
[ 19.804000] l2tp_core: L2TP core driver, V2.0
[ 19.812000] l2tp_netlink: L2TP netlink interface
[ 19.840000] gre: GRE over IPv4 demultiplexor driver
[ 19.852000] ip_gre: GRE over IPv4 tunneling driver
[ 19.904000] nf_conntrack version 0.5.0 (959 buckets, 3836 max)
[ 19.928000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 19.980000] u32 classifier
[ 19.984000] input device check on
[ 19.988000] Actions configured
[ 20.008000] Mirror/redirect action on
[ 20.080000] fuse init (API version 7.22)
[ 20.116000] usbcore: registered new interface driver cdc_acm
[ 20.124000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 20.156000] usbcore: registered new interface driver cdc_wdm
[ 20.168000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 20.176000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 20.208000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 20.236000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 20.368000] usbcore: registered new interface driver usblp
[ 20.416000] usbcore: registered new interface driver usbserial
[ 20.428000] usbcore: registered new interface driver usbserial_generic
[ 20.440000] usbserial: USB Serial support registered for generic
[ 20.604000] xt_time: kernel timezone is -0000
[ 20.620000] usbcore: registered new interface driver cdc_ether
[ 20.636000] usbcore: registered new interface driver cdc_ncm
[ 20.748000] cfg80211: Calling CRDA to update world regulatory domain
[ 20.768000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 20.784000] cfg80211: World regulatory domain updated:
[ 20.788000] cfg80211: DFS Master region: unset
[ 20.792000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 20.804000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 20.812000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 20.820000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 20.828000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 20.836000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 20.844000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 20.852000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 20.860000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 21.052000] PPP generic driver version 2.4.2
[ 21.064000] PPP MPPE Compression module registered
[ 21.072000] NET: Registered protocol family 24
[ 21.080000] PPTP driver version 0.8.5
[ 21.096000] usbcore: registered new interface driver qmi_wwan
[ 21.108000] usbcore: registered new interface driver rndis_host
[ 21.120000] usbcore: registered new interface driver sierra
[ 21.128000] usbserial: USB Serial support registered for Sierra USB modem
[ 21.196000] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
[ 21.236000] b43-phy0: Found PHY: Analog 3, Type 2 (G), Revision 7
[ 21.240000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2050, Revision 8, Versio
[ 21.392000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 21.404000] Error: Driver 'gpio-keys-polled' is already registered, aborting.
[ 21.424000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 21.436000] usbcore: registered new interface driver option
[ 21.444000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 21.464000] Error: Driver 'gpio-keys-polled' is already registered, aborting.
[ 21.700000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 30.336000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 30.840000] eth0: link UP - 100/full - flow control off
[ 30.848000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 46.864000] device eth0.1 entered promiscuous mode
[ 46.868000] device eth0 entered promiscuous mode
[ 46.888000] br-lan: port 1(eth0.1) entered forwarding state
[ 46.892000] br-lan: port 1(eth0.1) entered forwarding state
[ 47.856000] eth0: link UP - 100/full - flow control off
[ 48.896000] br-lan: port 1(eth0.1) entered forwarding state
[ 75.348000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 75.364000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 75.368000] jffs2_build_filesystem(): erasing all blocks after the end marker
[ 117.976000] jffs2: notice: (1702) jffs2_build_xattr_subsystem: complete build d, 0 orphan) found.
root@OpenWrt:~# ls /lib/modules/3.10.49/*
/lib/modules/3.10.49/act_connmark.ko /lib/modules/3.10.49/ip_tunnel.ko /lib/modules/3.10.49/sha1_generic.ko
/lib/modules/3.10.49/act_mirred.ko /lib/modules/3.10.49/ipt_ECN.ko /lib/modules/3.10.49/sierra.ko
/lib/modules/3.10.49/act_skbedit.ko /lib/modules/3.10.49/ipt_MASQUERADE.ko /lib/modules/3.10.49/slhc.ko
/lib/modules/3.10.49/aead.ko /lib/modules/3.10.49/ipt_REJECT.ko /lib/modules/3.10.49/ts_bm.ko
/lib/modules/3.10.49/arc4.ko /lib/modules/3.10.49/iptable_filter.ko /lib/modules/3.10.49/ts_fsm.ko
/lib/modules/3.10.49/b43.ko /lib/modules/3.10.49/iptable_mangle.ko /lib/modules/3.10.49/ts_kmp.ko
/lib/modules/3.10.49/bcma.ko /lib/modules/3.10.49/iptable_nat.ko /lib/modules/3.10.49/usb-common.ko
/lib/modules/3.10.49/button-hotplug.ko /lib/modules/3.10.49/iptable_raw.ko /lib/modules/3.10.49/usb-storage.ko
/lib/modules/3.10.49/cdc-acm.ko /lib/modules/3.10.49/ipv6.ko /lib/modules/3.10.49/usb_wwan.ko
/lib/modules/3.10.49/cdc-wdm.ko /lib/modules/3.10.49/jbd2.ko /lib/modules/3.10.49/usbcore.ko
/lib/modules/3.10.49/cdc_ether.ko /lib/modules/3.10.49/l2tp_core.ko /lib/modules/3.10.49/usblp.ko
/lib/modules/3.10.49/cdc_ncm.ko /lib/modules/3.10.49/l2tp_netlink.ko /lib/modules/3.10.49/usbnet.ko
/lib/modules/3.10.49/cfg80211.ko /lib/modules/3.10.49/l2tp_ppp.ko /lib/modules/3.10.49/usbserial.ko
/lib/modules/3.10.49/cls_flow.ko /lib/modules/3.10.49/ledtrig-usbdev.ko /lib/modules/3.10.49/vfat.ko
/lib/modules/3.10.49/cls_fw.ko /lib/modules/3.10.49/mac80211.ko /lib/modules/3.10.49/x_tables.ko
/lib/modules/3.10.49/cls_route.ko /lib/modules/3.10.49/mbcache.ko /lib/modules/3.10.49/xt_CLASSIFY.ko
/lib/modules/3.10.49/cls_tcindex.ko /lib/modules/3.10.49/nf_conntrack.ko /lib/modules/3.10.49/xt_CT.ko
/lib/modules/3.10.49/cls_u32.ko /lib/modules/3.10.49/nf_conntrack_ftp.ko /lib/modules/3.10.49/xt_DSCP.ko
/lib/modules/3.10.49/compat.ko /lib/modules/3.10.49/nf_conntrack_ipv4.ko /lib/modules/3.10.49/xt_HL.ko
/lib/modules/3.10.49/crc-ccitt.ko /lib/modules/3.10.49/nf_conntrack_ipv6.ko /lib/modules/3.10.49/xt_LOG.ko
/lib/modules/3.10.49/crc16.ko /lib/modules/3.10.49/nf_conntrack_irc.ko /lib/modules/3.10.49/xt_REDIRECT.ko
/lib/modules/3.10.49/crypto_blkcipher.ko /lib/modules/3.10.49/nf_conntrack_rtcache.ko /lib/modules/3.10.49/xt_TCPMSS.ko
/lib/modules/3.10.49/crypto_hash.ko /lib/modules/3.10.49/nf_defrag_ipv
/lib/modules/3.10.49/ecb.ko /lib/modules/3.10.49/nf_defrag_ipv
/lib/modules/3.10.49/ehci-hcd.ko /lib/modules/3.10.49/nf_nat.ko
/lib/modules/3.10.49/ehci-platform.ko /lib/modules/3.10.49/nf_nat_ftp.ko
/lib/modules/3.10.49/em_u32.ko /lib/modules/3.10.49/nf_nat_ipv4.k
/lib/modules/3.10.49/ext4.ko /lib/modules/3.10.49/nf_nat_irc.ko
/lib/modules/3.10.49/fat.ko /lib/modules/3.10.49/nls_base.ko
/lib/modules/3.10.49/fuse.ko /lib/modules/3.10.49/nls_cp437.ko
/lib/modules/3.10.49/gpio-button-hotplug.ko /lib/modules/3.10.49/nls_iso8859-1
/lib/modules/3.10.49/gpio_keys_polled.ko /lib/modules/3.10.49/ohci-hcd.ko
/lib/modules/3.10.49/gre.ko /lib/modules/3.10.49/option.ko
/lib/modules/3.10.49/i2c-core.ko /lib/modules/3.10.49/ppp_async.ko
/lib/modules/3.10.49/i2c-dev.ko /lib/modules/3.10.49/ppp_generic.k
/lib/modules/3.10.49/ifb.ko /lib/modules/3.10.49/ppp_mppe.ko
/lib/modules/3.10.49/input-core.ko /lib/modules/3.10.49/pppoe.ko
/lib/modules/3.10.49/input-polldev.ko /lib/modules/3.10.49/pppox.ko
/lib/modules/3.10.49/ip6_tables.ko /lib/modules/3.10.49/pptp.ko
/lib/modules/3.10.49/ip6t_REJECT.ko /lib/modules/3.10.49/qmi_wwan.ko
/lib/modules/3.10.49/ip6table_filter.ko /lib/modules/3.10.49/rndis_host.ko
/lib/modules/3.10.49/ip6table_mangle.ko /lib/modules/3.10.49/sch_hfsc.ko
/lib/modules/3.10.49/ip6table_raw.ko /lib/modules/3.10.49/sch_ingress.k
/lib/modules/3.10.49/ip_gre.ko /lib/modules/3.10.49/scsi_mod.ko
/lib/modules/3.10.49/ip_tables.ko /lib/modules/3.10.49/sd_mod.ko
root@OpenWrt:~# opkg list_installed | grep usb
kmod-ledtrig-usbdev - 3.10.49-1
kmod-usb-acm - 3.10.49-1
kmod-usb-core - 3.10.49-1
kmod-usb-net - 3.10.49-1
kmod-usb-net-cdc-ether - 3.10.49-1
kmod-usb-net-cdc-ncm - 3.10.49-1
kmod-usb-net-qmi-wwan - 3.10.49-1
kmod-usb-net-rndis - 3.10.49-1
kmod-usb-ohci - 3.10.49-1
kmod-usb-printer - 3.10.49-1
kmod-usb-serial - 3.10.49-1
kmod-usb-serial-option - 3.10.49-1
kmod-usb-serial-sierrawireless - 3.10.49-1
kmod-usb-serial-wwan - 3.10.49-1
kmod-usb-storage - 3.10.49-1
kmod-usb-wdm - 3.10.49-1
kmod-usb2 - 3.10.49-1
libusb-1.0 - 1.0.9-1
usb-modeswitch - 2014-07-18-01ecc3b9764d1dd89cf36ede0a2d98f9adb0cd33
root@OpenWrt:~#usb oczywiście działa
chciałbym zweryfikować że to co jest w pamięci routera odpowiada plikowi który wgrałem
jak zrzucić pamięć do pliku?
Odp: Chętny z Huawei HG553/HG556 potrzebny
Całą partycję firmware możesz zrzucić, choć takie porównywanie nic nie da.
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
Pokaż jeszcze cat /proc/cpuinfo
Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.
Odp: Chętny z Huawei HG553/HG556 potrzebny
root@OpenWrt:~# cat /proc/cpuinfo
system type : bcm63xx/HW553 (0x6358/0xA1)
machine : Unknown
processor : 0
cpu model : Broadcom BMIPS4350 V1.0
BogoMIPS : 297.98
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : no
isa : mips1 mips2 mips32r1
ASEs implemented :
shadow register sets : 1
kscratch registers : 0
core : 0
VCED exceptions : not available
VCEI exceptions : not availablePosty: 1 do 25 z 72
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → Chętny z Huawei HG553/HG556 potrzebny
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc