Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Posty przez zbynex
passwd pomimo potwierdzenia zmiany hasła nie dało się nowym zalogować.
Po firstboot wszystko wróciło do normy IP i Password. Jest już chyba wszystko OK. Przycisk RESET z tyłu obudowy wciąż nie reaguje a na oryginalnym firmware działał.
Co do zachowania konfiguracji przy aktualizacji to GUI Kimax nie ma wyboru. Jest tylko przywrócenie domyślnej konfiguracji i update firmware.
Myślę że ten post może być pomocny innym użytkownikom którzy będą wgrywać gargoyle z poziomu gui kimax.
Dzięki za pomoc.
Interfejs podłączony. I to co wypluwa przy starcie:
U-Boot 1.1.3 (Jan 29 2015 - 15:00:12)
Board: Ralink APSoC DRAM: 128 MB
relocate_code Pointer at: 87fb8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.2.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->Phy)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: SPI Flash
Date:Jan 29 2015 Time:15:00:12
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =128 Mbytes
hylon find this is RTL8211E Gagi Phy!!!
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.187
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1572852 Bytes = 1.5 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:17fff4
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 4.14.187 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10707-75d11f665c)) #0 Fri Jul 10 11:55:54 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Kimax U35WF
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] random: get_random_bytes called from 0x80487740 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00067fe6
[ 0.000000] Readback ErrCtl register=00067fe6
[ 0.000000] Memory: 123796K/131072K available (3937K kernel code, 186K rwdata, 504K rodata, 1188K init, 215K bss, 7276K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015478] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087724] pid_max: default: 32768 minimum: 301
[ 0.097136] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110165] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.129217] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.148696] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.160880] pinctrl core: initialized pinctrl subsystem
[ 0.172509] NET: Registered protocol family 16
[ 0.204079] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.215116] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.227705] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.238708] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.251292] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.262120] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.279431] clocksource: Switched to clocksource systick
[ 0.291093] NET: Registered protocol family 2
[ 0.300664] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.314449] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.327038] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.339812] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.351342] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.364029] NET: Registered protocol family 1
[ 0.375429] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.388146] Crashlog allocated RAM at address 0x3f00000
[ 0.400327] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.419034] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.430539] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.460836] io scheduler noop registered
[ 0.468479] io scheduler deadline registered (default)
[ 0.479716] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.495105] console [ttyS0] disabled
[ 0.502167] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.521845] console [ttyS0] enabled
[ 0.521845] console [ttyS0] enabled
[ 0.535657] bootconsole [early0] disabled
[ 0.535657] bootconsole [early0] disabled
[ 0.559785] spi spi0.0: force spi mode3
[ 0.568209] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.578383] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.591056] Creating 4 MTD partitions on "spi0.0":
[ 0.600622] 0x000000000000-0x000000030000 : "u-boot"
[ 0.611448] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.622994] 0x000000040000-0x000000050000 : "factory"
[ 0.633995] 0x000000050000-0x000001000000 : "firmware"
[ 0.648170] 2 uimage-fw partitions found on MTD device firmware
[ 0.660039] Creating 2 MTD partitions on "firmware":
[ 0.669957] 0x000000000000-0x000000180034 : "kernel"
[ 0.680743] 0x000000180034-0x000000fb0000 : "rootfs"
[ 0.691521] mtd: device 5 (rootfs) set to be root filesystem
[ 0.704494] 1 squashfs-split partitions found on MTD device rootfs
[ 0.716884] 0x0000008e0000-0x000000fb0000 : "rootfs_data"
[ 0.729391] libphy: Fixed MDIO Bus: probed
[ 0.746474] gsw: setting port4 to ephy mode
[ 0.755142] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.767654] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 0.784823] rt2880_wdt 10000120.watchdog: Initialized
[ 0.796282] NET: Registered protocol family 10
[ 0.809816] Segment Routing with IPv6
[ 0.817223] NET: Registered protocol family 17
[ 0.826191] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.852039] 8021q: 802.1Q VLAN Support v1.8
[ 0.861980] hctosys: unable to open rtc device (rtc0)
[ 0.883772] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.904478] Freeing unused kernel memory: 1188K
[ 0.913534] This architecture does not have kernel memory protection.
[ 2.647742] init: Console is alive
[ 2.654927] init: - watchdog -
[ 2.661064] random: fast init done
[ 8.325180] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.757463] usbcore: registered new interface driver usbfs
[ 8.768560] usbcore: registered new interface driver hub
[ 8.779295] usbcore: registered new device driver usb
[ 8.823436] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.845713] SCSI subsystem initialized
[ 8.859041] ehci-platform: EHCI generic platform driver
[ 8.879882] phy phy-usbphy.0: remote usb device wakeup disabled
[ 8.891704] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 8.900589] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 8.912091] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 8.928014] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 8.950598] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 8.964117] hub 1-0:1.0: USB hub found
[ 8.972067] hub 1-0:1.0: 1 port detected
[ 8.983672] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.998079] ohci-platform: OHCI generic platform driver
[ 9.008858] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 9.022488] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 9.038395] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 9.079582] hub 2-0:1.0: USB hub found
[ 9.087516] hub 2-0:1.0: 1 port detected
[ 9.103885] usbcore: registered new interface driver usb-storage
[ 9.118722] usbcore: registered new interface driver uas
[ 9.130146] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 9.149012] init: - preinit -
[ 9.288589] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 9.689147] usb 1-1: device descriptor read/64, error -71
[ 10.239118] usb 1-1: device descriptor read/64, error -71
[ 10.808589] usb 1-1: new high-speed USB device number 3 using ehci-platform
[ 11.238081] usb 1-1: device descriptor read/64, error -71
[ 11.748761] usb 1-1: device descriptor read/64, error -71
[ 11.945991] usb usb1-port1: attempt power cycle
[ 12.132649] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3[ 12.294831] random: procd: uninitialized urandom read (4 bytes read)
] or [4] key and hit [enter] to select the debug level
[ 12.426667] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 12.586801] usb 1-1: device not accepting address 4, error -71
[ 12.730080] usb 1-1: new high-speed USB device number 5 using ehci-platform
[ 12.890216] usb 1-1: device not accepting address 5, error -71
[ 12.901910] usb usb1-port1: unable to enumerate USB device
[ 13.061358] usb 2-1: new full-speed USB device number 2 using ohci-platform
[ 13.162304] usb 2-1: not running at top speed; connect to a high speed hub
[ 13.179968] hub 2-1:1.0: USB hub found
[ 13.188311] hub 2-1:1.0: 4 ports detected
[ 13.307670] usb 2-1.1: new full-speed USB device number 3 using ohci-platform
[ 13.656071] mount_root: loading kmods from internal overlay
[ 13.769222] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 13.788370] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 14.296596] usb 2-1.1: not running at top speed; connect to a high speed hub
[ 14.328754] usb-storage 2-1.1:1.0: USB Mass Storage device detected
[ 14.354474] scsi host0: usb-storage 2-1.1:1.0
[ 15.541889] scsi 0:0:0:0: Direct-Access ASMT 2115 0 PQ: 0 ANSI: 6
[ 15.586935] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 16.474881] jffs2: notice: (456) jffs2_build_xattr_subsystem: complete building xattr subsystem, 26 of xdatum (3 unchecked, 23 orphan) and 58 of xref (23 dead, 2 orphan) found.
[ 16.507344] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 16.541336] block: extroot: not configured
[ 17.023568] jffs2: notice: (454) jffs2_build_xattr_subsystem: complete building xattr subsystem, 26 of xdatum (3 unchecked, 23 orphan) and 58 of xref (23 dead, 2 orphan) found.
[ 18.886197] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 18.913932] block: extroot: not configured
[ 18.923552] mount_root: switching to jffs2 overlay
[ 19.035831] overlayfs: upper fs does not support tmpfile.
[ 19.057604] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 19.194800] procd: - early -
[ 19.200657] procd: - watchdog -
[ 19.427429] procd: cannot set group dialout for /dev/ttyS11 (getgrnam: 0)
[ 19.444428] procd: cannot set group dialout for /dev/ttyS8 (getgrnam: 0)
[ 19.459575] procd: cannot set group dialout for /dev/ttyS6 (getgrnam: 0)
[ 19.485860] procd: cannot set group dialout for /dev/ttyS4 (getgrnam: 0)
[ 19.517541] procd: cannot set group dialout for /dev/ttyS2 (getgrnam: 0)
[ 19.540846] procd: cannot set group dialout for /dev/ttyS14 (getgrnam: 0)
[ 19.576118] procd: cannot set group dialout for /dev/ttyS0 (getgrnam: 0)
[ 19.651291] procd: cannot set group dialout for /dev/ttyS12 (getgrnam: 0)
[ 19.666408] procd: cannot set group dialout for /dev/ttyS9 (getgrnam: 0)
[ 19.681086] procd: cannot set group dialout for /dev/ttyS10 (getgrnam: 0)
[ 19.695880] procd: cannot set group dialout for /dev/ttyS7 (getgrnam: 0)
[ 19.725518] procd: cannot set group dialout for /dev/ttyS5 (getgrnam: 0)
[ 19.757812] procd: cannot set group dialout for /dev/ttyS3 (getgrnam: 0)
[ 19.787753] procd: cannot set group dialout for /dev/ttyS15 (getgrnam: 0)
[ 19.817407] procd: cannot set group dialout for /dev/ttyS1 (getgrnam: 0)
[ 19.847326] procd: cannot set group dialout for /dev/ttyS13 (getgrnam: 0)
[ 20.413834] procd: - watchdog -
[ 20.420419] procd: - ubus -
[ 20.706730] random: ubusd: uninitialized urandom read (4 bytes read)
[ 20.728264] random: ubusd: uninitialized urandom read (4 bytes read)
[ 20.746247] random: ubusd: uninitialized urandom read (4 bytes read)
[ 20.760072] procd: - init -
Please press Enter to activate this console.
[ 21.753825] urandom_read: 5 callbacks suppressed
[ 21.753834] random: jshn: uninitialized urandom read (4 bytes read)
[ 23.155230] kmodloader: loading kernel modules from /etc/modules.d/*
[ 23.551484] urngd: jent-rng init failed, err: 2
[ 23.616706] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[ 23.679477] Key type dns_resolver registered
[ 23.870068] RPC: Registered named UNIX socket transport module.
[ 23.881948] RPC: Registered udp transport module.
[ 23.891336] RPC: Registered tcp transport module.
[ 23.900720] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 23.989399] tun: Universal TUN/TAP device driver, 1.6
[ 24.050896] gre: GRE over IPv4 demultiplexor driver
[ 24.075869] ip_gre: GRE over IPv4 tunneling driver
[ 24.156311] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 24.212913] NFS: Registering the id_resolver key type
[ 24.223087] Key type id_resolver registered
[ 24.231446] Key type id_legacy registered
[ 24.296191] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 24.393380] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 24.853215] Mirror/redirect action on
[ 24.895485] u32 classifier
[ 24.900877] input device check on
[ 24.908230] Actions configured
[ 24.968065] GACT probability on
[ 25.000773] Simple TC action Loaded
[ 25.092860] fuse init (API version 7.26)
[ 25.182238] usbcore: registered new interface driver cdc_acm
[ 25.193603] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 25.384898] usbcore: registered new interface driver cdc_wdm
[ 25.422516] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[ 25.437867] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[ 25.525785] Ebtables v2.0 registered
[ 25.543815] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 26.339638] usbcore: registered new interface driver ums-alauda
[ 26.367284] usbcore: registered new interface driver ums-cypress
[ 26.400272] usbcore: registered new interface driver ums-datafab
[ 26.436329] usbcore: registered new interface driver ums-freecom
[ 26.466622] usbcore: registered new interface driver ums-isd200
[ 26.486930] usbcore: registered new interface driver ums-jumpshot
[ 26.526346] usbcore: registered new interface driver ums-karma
[ 26.555319] usbcore: registered new interface driver ums-sddr09
[ 26.586632] usbcore: registered new interface driver ums-sddr55
[ 26.617205] usbcore: registered new interface driver ums-usbat
[ 26.648011] usbcore: registered new interface driver usblp
[ 26.708993] usbcore: registered new interface driver usbserial
[ 26.720806] usbcore: registered new interface driver usbserial_generic
[ 26.733942] usbserial: USB Serial support registered for generic
[ 26.809644] wireguard: WireGuard 1.0.20200611 loaded. See www.wireguard.com for information.
[ 26.826540] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 26.990587] xt_time: kernel timezone is -0000
[ 27.017714] usbcore: registered new interface driver cdc_ether
[ 27.055796] usbcore: registered new interface driver cdc_ncm
[ 27.267377] usbcore: registered new interface driver huawei_cdc_ncm
[ 27.548657] PPP generic driver version 2.4.2
[ 27.575670] NET: Registered protocol family 24
[ 27.595296] PPTP driver version 0.8.5
[ 27.618372] usbcore: registered new interface driver qmi_wwan
[ 27.644910] usbcore: registered new interface driver rndis_host
[ 27.724699] usbcore: registered new interface driver sierra
[ 27.735959] usbserial: USB Serial support registered for Sierra USB modem
[ 27.787084] usbcore: registered new interface driver sierra_net
[ 27.827034] usbcore: registered new interface driver cdc_mbim
[ 27.866158] usbcore: registered new interface driver option
[ 27.877447] usbserial: USB Serial support registered for GSM modem (1-port)
[ 27.925415] usbcore: registered new interface driver qcserial
[ 27.937035] usbserial: USB Serial support registered for Qualcomm USB modem
[ 28.050398] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 28.064885] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 28.080355] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 28.154163] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 47.271340] 8021q: adding VLAN 0 to HW filter on device eth0
[ 47.314418] br-lan: port 1(eth0.1) entered blocking state
[ 47.325270] br-lan: port 1(eth0.1) entered disabled state
[ 47.336431] device eth0.1 entered promiscuous mode
[ 47.346025] device eth0 entered promiscuous mode
[ 47.441237] br-lan: port 1(eth0.1) entered blocking state
[ 47.452069] br-lan: port 1(eth0.1) entered forwarding state
[ 47.463415] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 48.314322] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 57.757956] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
[ 57.774577] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
[ 62.240133] ieee80211 phy0: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
[ 62.259628] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
[ 62.287581] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= f, phase=3d)
[ 62.306719] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
[ 62.334654] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= 1, phase=3e)
[ 62.352904] ieee80211 phy0: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
[ 62.606468] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=-2, Ph_rx=5
[ 62.629416] ieee80211 phy0: rt2800_rxiq_calibration: Warning - RXIQ calibration FAIL
[ 62.717401] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 62.750518] br-lan: port 2(wlan0) entered blocking state
[ 62.761190] br-lan: port 2(wlan0) entered disabled state
[ 62.772199] device wlan0 entered promiscuous mode
[ 63.721409] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 63.734378] br-lan: port 2(wlan0) entered blocking state
[ 63.745022] br-lan: port 2(wlan0) entered forwarding state
[ 79.520010] random: crng init doneCezary proszę poprowadż mnie krok po kroku żebym nie uwalił go do końca 
Diodą systemową tutaj jest znaczek wifi. Ale niestety nie reaguje na przycisk. Jutro podlutuje interfejs. Podpowiedz mi jeszcze jakie parametry serial dla bootloadera mają być ?
Jaka szansa odratowania go jest ?
Bo nie bardzo wiem gdzie serial w nim podpiąc.
W takim razie coś ten obraz firmware jest nie halo.
Router nie odpowiada na 192.168.1.1
Wgrałem dokładnie to: https://dl.eko.one.pl/gargoyle-pl/openw … pgrade.bin
Jak mogłem wgrać coś innego skoro wyświetla mi się strona logowania gargoyle z podanym adresem klienta tym co ja mam przydzielony.
Właśnie zrobiłem próbę połączenia się na LinuxMint i ta sama sytuacja.
No niestety nie reaguje na przycisk reset i nie można wejść w failsafe.
Natomiast router przydziela dla klienta wifi adres z puli 192.168.169.1
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : fdf5:eaf0:1a3d::52e(Preferred)
Lease Obtained. . . . . . . . . . : wtorek, 6 października 2020 19:55:11
Lease Expires . . . . . . . . . . : sobota, 13 listopada 2156 02:38:33
IPv6 Address. . . . . . . . . . . : fdf5:eaf0:1a3d:0:55c8:d288:ec89:1ec0(Preferred)
Temporary IPv6 Address. . . . . . : fdf5:eaf0:1a3d:0:956a:3b25:e224:fbb7(Preferred)
Link-local IPv6 Address . . . . . : fe80::55c8:d288:ec89:1ec0%13(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.169.150(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : wtorek, 6 października 2020 19:55:10
Lease Expires . . . . . . . . . . : środa, 7 października 2020 08:09:45
Default Gateway . . . . . . . . . : 192.168.169.1
DHCP Server . . . . . . . . . . . : 192.168.169.1
DHCPv6 IAID . . . . . . . . . . . : 90467945
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-21-6E-83-0F-98-29-A6-18-79-2D
DNS Servers . . . . . . . . . . . : fdf5:eaf0:1a3d::1
192.168.169.1
NetBIOS over Tcpip. . . . . . . . : EnabledAktualizowałem z oryginalnego firmware kimax
No niestety wygląda że przycisk reset nie reaguje z tym firmware.
Dalej odpowiada tylko na 192.168.169.1
Jakieś pomysły jak go uratować ?
Jest z tyłu ale jakby nie reagował. Ile go mam trzymać ?
Jak to mam zrobić ?
Połączony jestem na pewno z dobrą siecią wifi "gargoyle" bo jak go wyłączam to rozłącza połączenie. Na adres 192.168.1.1 nie odpowiada router natomiast 192.168.169.1 otwiera się strona logowania. Po kablu od strony wan tez sie nie oddzywa.
Czy ten firmware ktoś wcześniej już testował ?
Tak wgrałem gargoyle i niestety po podaniu hasła nawet nie wyświetla że złe tylko jakby ponownie chciał hasło.
Przez putty również nie można się zalogować. user: root password: password.
Obraz wgrał się bezproblemowo. Do sieci wifi "gargoyle" hasło "password" działa natomiast do gui jak w kólko chciał aby wprowadzać ponownie.
login as: root
root@192.168.169.1's password:
Access denied
root@192.168.169.1's password:Cezary a czy coś się zmieniło odnośnie domyślnego hasła do routera ?
Adres routera po połączeniu przez wifi jest jak w kimax 192.168.169.1 natomiast żadne z haseł nie wchodzi "password" "kimax" "12345678"
Jakie jest domyślne hasło do GUI ?
Wielkie dzięki.
Pozdrawiam
A które gargoyle bo nie znalazłem nigdzie linku ?
Można prosić o link do gargoyle ?
Witam
Chciałbym zapytać czy coś można poza czystym openwrt wgrać na ten sprzęt Blueendless BS - U35WF najlepiej z GUI ?
Jeżeli chodzi o MR3420V2 WR842V2 to są w 100% zgodne. Sam mam wgrane na kilku sztukach soft z 842V2 i wszystko jest zgodne.
Najprościej migrować na flash 16M jest poprzez bootloader Pepe2k. Zgrywasz z routera ART potem na nowy flash wgrywasz bootloader, lutujesz go do routera a reszta przez przeglądarkę i bootloader Pepe2k. Możesz kombinować do woli i zawsze w prosty sposób bez rozbierania routera postawisz go na nogi
W takim razie pozostaje mi czekać. Dzięki
A kiedy można spodziewać się pierwszej wersji z identyfikacją wielkości flasha ?
A jesteś w stanie zrobić kompilację na 16M ?
Czyli jeżeli rozumiem mógłbyś skompilować na wersję 842 v2. Jeżeli to możliwe to bardzo bym Cię prosił.
Przed chwilą wgrałem 1.13 na 842nV2 ale wskazuje brak miejsca na wireguard więc tylko wersja 16M. Jeszcze jest mały problem bo WiFi nie można włączyć.
Wersja 842Nv2 skompilowana na 16M też pewnie by działała na modowanym MR3420V2 bo obecnie na nie wgrywam właśnie soft z 842N.
Gdyby to nie był wielki problem dla Ciebie Cezary to w wolnej chwili proszę skompiluj taką wersję.
Witam
Posiadam WR842N V2 i WR842N V3 przerobiony MOD RAM 64M i Flash 16M i nie ma już na tą wersję Gargoyle 1.13 choć wersja modowana powinna bez problemu sobie z nim poradzić.
Jak w temacie chciałbym zapytać czy jest szansa zainstalowania Wireguard z GUI tak jak na gargoyle 1.13 ?
Niestety OpenVPN na tym sprzęcie strasznie obcina transfery.
Cezary czy jest jakaś szansa abyś skompilował najnowsze Gargoyle na modowany sprzęt ?
Już jest OK. Dzięki.
Router wstał ale po zalogowaniu w gui u góry ciągle komunikat:
Pamięć flash routera jest zapełniona (zamontowania w trybie tylko do odczytu) lub tymczasowo wykorzystywana jest pamięć RAM. Router nie będzie działać poprawnie lub powróci do stanu poprzedniego po ponownym uruchomieniu. Przywróć domyślną konfigurację lub wgraj nowe oprogramowanie (bez zachowania ustawień).Przywrócenie domyślnej konfiguracji nie pomaga.
Terminal wypluwa to:
U-Boot 1.1.3 (Jan 3 2014 - 09:12:42)
MAX Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
Warning: un-recognized chip ID, please update bootloader!
raspi_read: from:30000 len:1000
raspi_read: from:30000 len:1000
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 3 2014 Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-4.14.187
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1573070 Bytes = 1.5 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:1800ce
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 4.14.187 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10707-75d11f665c)) #0 Sun Aug 2 16:16:00 2020
[ 0.000000] Board has DDR1
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Nexx WT3020 (16M)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] random: get_random_bytes called from 0x80487740 with crng_init=0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00040005
[ 0.000000] Readback ErrCtl register=00040005
[ 0.000000] Memory: 58824K/65536K available (3937K kernel code, 186K rwdata, 504K rodata, 1188K init, 215K bss, 6712K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015470] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087713] pid_max: default: 32768 minimum: 301
[ 0.097119] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110148] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.129088] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.148561] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.160741] pinctrl core: initialized pinctrl subsystem
[ 0.172304] NET: Registered protocol family 16
[ 0.203114] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.214142] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.226720] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.237717] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.250292] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.261111] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.278193] clocksource: Switched to clocksource systick
[ 0.289814] NET: Registered protocol family 2
[ 0.299352] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.313130] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.325721] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.338492] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.350012] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.362693] NET: Registered protocol family 1
[ 0.373975] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.386658] Crashlog allocated RAM at address 0x3f00000
[ 0.398743] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.417447] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.428947] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.458886] io scheduler noop registered
[ 0.466528] io scheduler deadline registered (default)
[ 0.477644] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.493023] console [ttyS0] disabled
[ 0.500078] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.519755] console [ttyS0] enabled
[ 0.519755] console [ttyS0] enabled
[ 0.533573] bootconsole [early0] disabled
[ 0.533573] bootconsole [early0] disabled
[ 0.557226] spi spi0.0: force spi mode3
[ 0.575703] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.585144] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.597814] Creating 4 MTD partitions on "spi0.0":
[ 0.607381] 0x000000000000-0x000000030000 : "u-boot"
[ 0.618169] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.629707] 0x000000040000-0x000000050000 : "factory"
[ 0.640680] 0x000000050000-0x000001000000 : "firmware"
[ 0.654721] 2 uimage-fw partitions found on MTD device firmware
[ 0.666583] Creating 2 MTD partitions on "firmware":
[ 0.676498] 0x000000000000-0x00000018010e : "kernel"
[ 0.687264] 0x00000018010e-0x000000fb0000 : "rootfs"
[ 0.698014] mtd: device 5 (rootfs) set to be root filesystem
[ 0.710898] 1 squashfs-split partitions found on MTD device rootfs
[ 0.723279] 0x000000776000-0x000000fb0000 : "rootfs_data"
[ 0.735725] libphy: Fixed MDIO Bus: probed
[ 0.752487] gsw: setting port4 to ephy mode
[ 0.761096] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.773579] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 0.790715] rt2880_wdt 10000120.watchdog: Initialized
[ 0.802138] NET: Registered protocol family 10
[ 0.815393] Segment Routing with IPv6
[ 0.822870] NET: Registered protocol family 17
[ 0.831799] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.857641] 8021q: 802.1Q VLAN Support v1.8
[ 0.867523] hctosys: unable to open rtc device (rtc0)
[ 0.890948] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.911520] Freeing unused kernel memory: 1188K
[ 0.920575] This architecture does not have kernel memory protection.
[ 2.648194] random: fast init done
[ 2.659029] init: Console is alive
[ 2.666040] init: - watchdog -
[ 7.427567] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.790138] usbcore: registered new interface driver usbfs
[ 7.801235] usbcore: registered new interface driver hub
[ 7.811951] usbcore: registered new device driver usb
[ 7.853744] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.875730] SCSI subsystem initialized
[ 7.888793] ehci-platform: EHCI generic platform driver
[ 7.909574] phy phy-usbphy.0: remote usb device wakeup disabled
[ 7.921392] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 7.930274] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 7.941793] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 7.957706] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 7.979937] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 7.993413] hub 1-0:1.0: USB hub found
[ 8.001328] hub 1-0:1.0: 1 port detected
[ 8.017017] usbcore: registered new interface driver usb-storage
[ 8.031731] usbcore: registered new interface driver uas
[ 8.043066] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.061625] init: - preinit -
[ 10.239326] 8021q: adding VLAN 0 to HW filter on device eth0
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3[ 10.382783] random: procd: uninitialized urandom read (4 bytes read)
] or [4] key and hit [enter] to select the debug level
[ 11.634437] mount_root: loading kmods from internal overlay
[ 11.725453] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 11.744584] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 14.113063] block: attempting to load /etc/config/fstab
[ 14.125774] block: unable to load configuration (fstab: Entry not found)
[ 14.139297] block: no usable configuration
[ 14.148358] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 14.246524] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 14.383220] procd: - early -
[ 14.389064] procd: - watchdog -
[ 15.183485] procd: - watchdog -
[ 15.190186] procd: - ubus -
[ 15.484364] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.795776] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.822144] random: ubusd: uninitialized urandom read (4 bytes read)
[ 15.848953] procd: - init -
Please press Enter to activate this console.
[ 17.619070] kmodloader: loading kernel modules from /etc/modules.d/*
[ 18.064356] Key type dns_resolver registered
[ 18.190024] RPC: Registered named UNIX socket transport module.
[ 18.201883] RPC: Registered udp transport module.
[ 18.211267] RPC: Registered tcp transport module.
[ 18.220649] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 18.322050] tun: Universal TUN/TAP device driver, 1.6
[ 18.343798] urngd: jent-rng init failed, err: 2
[ 18.438656] gre: GRE over IPv4 demultiplexor driver
[ 18.491373] ip_gre: GRE over IPv4 tunneling driver
[ 18.629835] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 18.654803] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.700562] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 18.930161] fuse init (API version 7.26)
[ 18.969063] usbcore: registered new interface driver cdc_acm
[ 18.980420] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 19.031339] usbcore: registered new interface driver cdc_wdm
[ 19.057055] Loading modules backported from Linux version v4.19.120-0-gfdc072324f3c
[ 19.072380] Backport generated by backports.git v4.19.120-1-0-g60c3a249
[ 19.142673] Ebtables v2.0 registered
[ 19.161992] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.588689] usbcore: registered new interface driver ums-alauda
[ 19.618239] usbcore: registered new interface driver ums-cypress
[ 19.651808] usbcore: registered new interface driver ums-datafab
[ 19.678880] usbcore: registered new interface driver ums-freecom
[ 19.711803] usbcore: registered new interface driver ums-isd200
[ 19.734217] usbcore: registered new interface driver ums-jumpshot
[ 19.761579] usbcore: registered new interface driver ums-karma
[ 19.792553] usbcore: registered new interface driver ums-sddr09
[ 19.821603] usbcore: registered new interface driver ums-sddr55
[ 19.852175] usbcore: registered new interface driver ums-usbat
[ 19.882859] usbcore: registered new interface driver usblp
[ 19.935810] usbcore: registered new interface driver usbserial
[ 19.947590] usbcore: registered new interface driver usbserial_generic
[ 19.960730] usbserial: USB Serial support registered for generic
[ 20.118328] xt_time: kernel timezone is -0000
[ 20.135365] usbcore: registered new interface driver cdc_ether
[ 20.174682] usbcore: registered new interface driver cdc_ncm
[ 20.371249] usbcore: registered new interface driver huawei_cdc_ncm
[ 20.591004] PPP generic driver version 2.4.2
[ 20.621168] NET: Registered protocol family 24
[ 20.641016] PPTP driver version 0.8.5
[ 20.663618] usbcore: registered new interface driver qmi_wwan
[ 20.688359] usbcore: registered new interface driver rndis_host
[ 20.758843] usbcore: registered new interface driver sierra
[ 20.770131] usbserial: USB Serial support registered for Sierra USB modem
[ 20.809385] usbcore: registered new interface driver sierra_net
[ 20.852376] usbcore: registered new interface driver cdc_mbim
[ 20.881866] usbcore: registered new interface driver option
[ 20.893144] usbserial: USB Serial support registered for GSM modem (1-port)
[ 20.940993] usbcore: registered new interface driver qcserial
[ 20.952601] usbserial: USB Serial support registered for Qualcomm USB modem
[ 21.056861] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 21.071341] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 21.086804] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 21.146162] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 71.652461] 8021q: adding VLAN 0 to HW filter on device eth0
[ 71.686562] br-lan: port 1(eth0.1) entered blocking state
[ 71.697554] br-lan: port 1(eth0.1) entered disabled state
[ 71.708691] device eth0.1 entered promiscuous mode
[ 71.718278] device eth0 entered promiscuous mode
[ 71.808551] br-lan: port 1(eth0.1) entered blocking state
[ 71.819374] br-lan: port 1(eth0.1) entered forwarding state
[ 71.830720] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 72.700363] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 78.102869] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
[ 78.119455] ieee80211 phy0: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
[ 82.916713] ieee80211 phy0: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
[ 82.936201] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
[ 82.963696] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 1, phase=3b)
[ 82.982821] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Start!
[ 83.010752] ieee80211 phy0: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= 1, phase=3e)
[ 83.029003] ieee80211 phy0: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
[ 83.071492] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=0, Ph_rx=-2
[ 83.096862] ieee80211 phy0: rt2800_rxiq_calibration: Info - RXIQ G_imb=1, Ph_rx=0
[ 83.186664] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 83.237219] br-lan: port 2(wlan0) entered blocking state
[ 83.247880] br-lan: port 2(wlan0) entered disabled state
[ 83.258865] device wlan0 entered promiscuous mode
[ 85.149832] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 85.162760] br-lan: port 2(wlan0) entered blocking state
[ 85.173397] br-lan: port 2(wlan0) entered forwarding state
[ 96.250273] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 96.276221] jffs2_build_filesystem(): unlocking the mtd device...
[ 96.279756] done.
[ 96.295981] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 96.329724] random: crng init done
[ 96.351401] random: 6 urandom warning(s) missed due to ratelimitingeko.one.pl → Posty przez zbynex
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc