FAQ o OpenWrt | Sprzedam różne routery | Oddam

2020-04-09 18:09:25

Cezary napisał/a:

Ustaw w fstabie opcję check_fs na 1. Przecież o to się pytałeś a nie o zrobienie extroota.

Szefie, ale ja tam mam ustawione check_fs na 1. Nie wpadł bym że o to chodzi. Ja ciągle się uczę i chwała Ci za Twoją Cierpliwość :-)

tak mam bez pendraka włożonego. Chociaż tu nie grzebałem wcześniej. (etc/config/fstab)

config global
        option anon_swap '0'
        option anon_mount '0'
        option auto_swap '1'
        option auto_mount '1'
        option delay_root '5'
        option check_fs '1'

config mount
        option target '/overlay'
        option uuid 'b495985b-337a-xxxx-86a8-214259458817'
        option fstype 'ext4'
        option options 'rw,noatime'
        option enabled '1'

2020-04-09 17:22:33

Cezary napisał/a:

https://eko.one.pl/?p=openwrt-externalr … szewydania opcja check_fs='1'. Tylko pamiętaj że masz to zrobić we flash (czyli odłącz extroota, uruchom bez pendrive i we flash ustaw) a nie na samym extroocie.

Nie mogę zaskoczyć co miał bym zrobić ? extroota już mam, w routerze siedzi kostka 16MB. Czytając to wydaje mi się że to instrukcja jak zrobić extroota..

2020-04-09 14:29:40

Cezary napisał/a:

Sobie jeszcze fsck ustaw na starce we flash jak nie masz.

A co to takiego i jak to zrobić?

2020-04-09 14:16:54

Cezary napisał/a:

Nie, nie wywalaj. Po prostu zmień option handler 'logger reboot ; /sbin/wifionoff ;' na option handler 'sync; poweroff;' i to wszystko...

Więc zmieniłem jak napisałeś ostatecznie , podłączyłem się jeszcze w międzyczasie pod serial aby widzieć co sie dzieje po przyciśnięciu wps

 Port /dev/ttyUSB0, 14:05:36

Wciśnij CTRL-A Z po po+-----------------------------------+
                      |                                   |
[  914.699241] br-lan:|  Nie mogę otworzyć /dev/ttyUSB0!  |
[  914.704870] br-lan:|                                   |
[  914.710357] br-lan:+-----------------------------------+e
[  914.753943] device eth0.1 left promiscuous mode
[  914.759540] device eth0 left promiscuous mode
[  914.765939] br-lan: port 1(eth0.1) entered disabled state
[  914.794823] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[  914.814716] device wlan0 left promiscuous mode
[  914.820387] br-lan: port 3(wlan0) entered disabled state
[  914.876169] device wlan1 left promiscuous mode
[  914.882644] br-lan: port 2(wlan1) entered disabled state
[  915.145911] eth0: link down
[  919.878546] reboot: Power down

Z tym portem tak krzyczał już po fakcie jak wyciągłem wtykę usb

a tym pliku /etc/config/system mam teraz tak (mam nadzieję że literówki nie zrobiłem) bo dygam aby napewno się poprawnie zamknął żeby extroot się nie wysypywał w przyszłości..

config button 'wps_button'
        option button 'wps'
        option action 'released'
        option handler 'sync; poweroff;'
        option min '0'
        option max '2'

i jeszcze apropo wysypywania sie extrota. Zanim zrobiłem kopię pendraka poprzez DD kilka razy zdaje się wcześniej wyłaczyłem go na szybko
bez sync && poweroff ale na tej kopi wstaje za każdym razem. Więc chyba powinienem być spokojny skoro działa i nic się nie sypie?

2020-04-09 12:51:20

Cezary napisał/a:

Ma być nazwa przycisku, wps jeżeli jest wpis.
A wifi ci wyłącza bo pewnie masz /etc/rc.button/wps i tam masz kod od wifi. Więc nie rób tego w /etc/hotplug.d/button/00-button
tylko zobacz co masz w /etc/rc.button/wps, wywal to i wstaw swój kod.

w /etc/rc.button/wps mam

#!/bin/sh

. /lib/functions.sh
do_button () {
        local button
        local action
        local handler
        local min
        local max

        config_get button $1 button
        config_get action $1 action
        config_get handler $1 handler
        config_get min $1 min
        config_get max $1 max

        [ "$ACTION" = "$action" -a "$BUTTON" = "$button" -a -n "$handler" ] && {
                [ -z "$min" -o -z "$max" ] && eval $handler
                [ -n "$min" -a -n "$max" ] && {
                        [ $min -le $SEEN -a $max -ge $SEEN ] && eval $handler
                }
        }
}

config_load system
config_foreach do_button button

ale przeglądając wcześniej /etc/config jest tam też coś takiego

config button 'wps_button'
        option button 'wps'
        option action 'released'
        option handler 'logger reboot ; /sbin/wifionoff ;'
        option min '0'
        option max '2'

więc zobaczyłem co jest w /sbin/wifionoff
i tam też jest jakiś skrypt

#!/bin/sh

IFACE=$(uci -q get wireless.@wifi-iface[0])
[ -z $IFACE ] && exit

W=$(iwinfo)
if [ -z "$W" ]; then
        wifi up
else
        wifi down
fi

exit 0

pytałem o ten reset wczęsniej bo w logu też się to pojawiło pomimo że naciskałem jeden przycisk

Thu Apr  9 11:59:26 2020 user.notice root: wps
Thu Apr  9 11:59:26 2020 user.notice root: pressed
Thu Apr  9 11:59:26 2020 user.notice root: reboot
Thu Apr  9 11:59:27 2020 user.notice root: wps
Thu Apr  9 11:59:27 2020 user.notice root: released

Póki co zrobię jak karzesz, wywalam z /etc/rc.button/wps i wstawię swój może się uda..

2020-04-09 12:27:13

Cezary napisał/a:

Nie. Napisałem w poprzednim poście - sterujesz ledami a nie bezpośrednio gpio, więc dajesz odpowiednią ścieżkę do ledów a nie do gpio.
Opis działania przycisków jest na eko.one.pl, możesz sobie podpiąć tam dowolną akcję, także poweroff. Czytaj: https://eko.one.pl/?p=openwrt-button#ba … ripniejsze

sterowanie przez usb_relay trzema diodami w routerze działa wyśmienicie.

tylko nie rozumiem za bardzo tych obsługi przycisków

stworzyłem katalog button
odczytałem po logread nazwę moich przycisków (jeden)

Thu Apr  9 11:59:26 2020 user.notice root: wps
Thu Apr  9 11:59:26 2020 user.notice root: pressed
Thu Apr  9 11:59:26 2020 user.notice root: reboot
Thu Apr  9 11:59:27 2020 user.notice root: wps
Thu Apr  9 11:59:27 2020 user.notice root: released

utworzyłem w katalogu /etc/hotplug.d/button plik 00-button
i w tym pliku mam tak zrobić ?

    if [ "$ACTION" = "pressed" ]; then
        if [ "$BUTTON" = "wps" ]; then
         sync && poweroff
        fi
    fi

Tylko teraz czy to po if [ "$BUTTON" = ma być wps, czy reboot ? no i jeśli miało by to zadziałać - to jak to się ma z działaniem dotychczasowym, tzn jak nacisnąłem przycisk to wyłączyłem WiFi ,jak nacisnąłem jeszcze raz to WiFi się włączyło.

Czy wystarczy z uci

    # uci add system button
    # uci set system.@button[-1].button=wps
    # uci set system.@button[-1].action=pressed
    # uci set system.@button[-1].handler='sync && poweroff'
    # uci commit system

2020-04-09 10:27:43

Cezary napisał/a:

Nie sterowanie masą tylko stanem aktywnym jest stan niski, zrobiłeś skrót myślowy.
Możesz podłączyć się pod te diody które nie są wykorzystywane przez system. qss nie jest, usb jak wywalisz z /etc/config/system definicje. Inne już wymagają rekompilacji systemu.

Czyli edytowałem plik system i usunałem całkiem te sekcje

config led 'led_usb1'
    option name 'USB1'
    option sysfs 'tp-link:green:usb1'
    option trigger 'usbdev'
    option interval '50'
    option dev '1-1.1'

config led 'led_usb2'
    option name 'USB2'
    option sysfs 'tp-link:green:usb2'
    option trigger 'usbdev'
    option interval '50'
    option dev '1-1.2'

czy teraz posiłkując się tym

root@Gargoyle:~# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 0-31, parent: platform/ath79-gpio, ath79-gpio:
 gpio-11  (                    |tp-link:green:usb1  ) out lo    
 gpio-12  (                    |tp-link:green:usb2  ) out lo    
 gpio-13  (                    |tp-link:blue:wlan2g ) out hi    
 gpio-14  (                    |tp-link:blue:system ) out lo    
 gpio-15  (                    |tp-link:blue:qss    ) out hi    
 gpio-16  (                    |QSS button          ) in  hi    
 gpio-17  (                    |RFKILL switch       ) in  lo    
 gpio-18  (                    |external LNA0       ) out hi    
 gpio-19  (                    |external LNA1       ) out hi    
 gpio-21  (                    |USB2 power          ) out hi    
 gpio-22  (                    |USB1 power          ) out hi    

gpiochip2: GPIOs 473-488, ath9k-phy1:
 gpio-473 (                    |ath9k-phy1          ) out lo    

gpiochip1: GPIOs 489-511, ath9k-phy0:
 gpio-490 (                    |ath9k-phy0          ) in  lo    
root@Gargoyle:~#

uznaje ze za sterowanie diodami USB są odpowiedzialne GPIO-11 i GPIO-12
i wystarczy że zmienię w tych liniach
LED2="/sys/class/gpio/gpio18/value" z 18na 11
LED3="/sys/class/gpio/gpio7/value" z 7 na 12 i powinno grać??

---

mam jeszcze sprawę odnośnie resetu ( czy też wyłączania) urządzenia z extrootem. Czy można by dopisać gdzieś w
config button 'reboot_button' zeby wykonał taką akcje "sync && poweroff" np po naciśnięciu w specyficzny sposób przycisku?
bo doszedłem do wniosku że wcześniejsze problemy z restartami wiązały się z wyłaczaniem urządzenia jak zwykle i wysypywał się system na extroocie. Po przywróceniu obrazu systemu na USB znowu jest stabilny.

2020-04-09 07:56:59

Cezary napisał/a:

Co ty z tym "sterowaniu masą"? Bo stanowczo mylisz pojęcia lub używasz je w nieprawidłowym kontekście. Co właściwie chcesz osiągnąć?
Tak, zamiast /sys/class/gpio/gpioX/value podstaw ścieżkę do diody, /sys/class/leds/wrt160nl:blue:wps/brightness (wg przykładu, ty podstaw swoje).
PS. Za dolara lub mniej kupisz na aliexpresie lub allegro gotowe moduły przekaźników do arduno/esp8266 itp. Nawet nie opłaca ci się tego robić samemu.

właśnie chodzi o to że mam teki moduł 4 kanałowy i używam go już w alarmie przy sterowaniu GSM i tam sterowanie wyjściami odbywa się masą i w tym module też mam tak ustawione zworkami - bo ustawienie jest do wszystkich 4 kanałów. Dlatego o tej masie gadam. To chodziło by pod wspólnym zasilaniem, więc teoretycznie włączając diodę qss podał bym masę przez ten optotriak na wolny kanał tego modułu i go załączył.

a odnośnie usb relay to widzę że są teraz tam 3 przyciski - szkoda było by dwóch które pozostaną nie wykorzystać w przyszłości.
w WDR3600 prócz tego qss co bys polecił aby wykorzystać do pozostałych dwóch przycisków usb relay?

2020-04-09 07:35:47

Cezary napisał/a:

Podmienić skrypt. Nawet przykład masz w linku który podałem...

Więc sterowanie diodą qss poprzez polecenia dają żądany efekt
echo "255" > /sys/class/leds/tp-link:blue:qss/brightness
echo "0" > /sys/class/leds/tp-link:blue:qss/brightness

w temacie OpenWrt GPIO / Sterowanie przekaźnikiem są podane linki do możliwych schematów, działa tylko ten http://fabrizio.zellini.org/wp-content/ … fonera.png

Jeśli ja chce sterować masą i wykorzystam to "moc3020m" to wystarczy że na jego wyjściu podłącze masę, a drugi pin do przekaźnika gdzie podaje na wejsciu masę? Czy diodę qss mogę zostawić do sygnalizownia stanu. czy lepiej ją wywalić?

No i teraz ten skrypt (podmieniłem już na ten od sterowania GPIO)

LED1="/sys/class/gpio/gpio2/value"
LED2="/sys/class/gpio/gpio18/value"
LED3="/sys/class/gpio/gpio7/value"

case "$1" in
    off)
        case $2 in
            1)
            echo "0" > $LED1
            ;;
            2)
            echo "0" > $LED2
            ;;
            3)
            echo "0" > $LED3
            ;;
        esac
        ;;
    on)
        case $2 in
            1)
            echo "1" > $LED1
            ;;
            2)
            echo "1" > $LED2
            ;;
            3)
            echo "1" > $LED3
            ;;
        esac
        ;;
    status)
        echo -n "1:"
        [ $(cat $LED1) -eq "0" ] && echo "off" || echo "on"
        echo -n "2:"
        [ $(cat $LED2) -eq "0" ] && echo "off" || echo "on"
        echo -n "3:"
        [ $(cat $LED3) -eq "0" ] && echo "off" || echo "on"
        ;;
esac

exit 0

Co trzeba zrobić aby sterować tą diodą poprzez usb relay? wiem żę edytować skrypt, ale nie mam pojęcia jak?

pewnie nie wystarczy w którymś z tych wierszy zmienić nr GPIO odpowiedzialny za sterowanie diodą qss ?

LED1="/sys/class/gpio/gpio2/value"
LED2="/sys/class/gpio/gpio18/value"
LED3="/sys/class/gpio/gpio7/value"

2020-04-08 22:52:27

Cezary napisał/a:

Żeby wykorzystać gpio w jtagu musiał byś najpierw zamienić jtag na gpio, a to się wiąże z kompilacją całości.
Sterujesz linią gpio a nie masą. Tak, zamiast diody.
usbrelay to ogólna nazwa pluginu. On wykorzystywał dodatkowy skrypt, a czy skrypt steruje przekaźnikiem na usb czy liniami gpio to już zależy jaki skrypt zrobisz.
Nie wiem jak patrzyłeś, ale ustawienia czasowe tam są: https://eko.one.pl/forum/viewtopic.php?pid=99432#p99432
EDIT: to jest oczywiście plugin do gargoyle jak by coś.

Jeśli chciałbym posłużyć się usb relay to wówczas po instalacji musiałbym podmienić skrypt czy też go edytować ?

Dziękuje Ci za cenne wskazówki. Pogłówkuje nad tym i spróbuje w wolnej chwili coś stworzyć..

2020-04-08 22:24:27

Cezary napisał/a:

Podłącz się pod led qss, ona nie jest wykorzystywana. O włączeniu/wyłączeniu diody masz tu: https://eko.one.pl/?p=openwrt-leds#wczeniediody (poćwicz to - tylko pamiętaj że dioda inaczej sie nazywa niż w poradniku!), zaś samo włączenie możesz zrealizować przez crona ( https://eko.one.pl/?p=openwrt-cron ). Harmonogramu wifi nie przerobisz do takich celów, ale możesz zastosować mój usb realy ( skrypty do sterowania przez gpio też były na forum).

Okej z diodą z pewnością poćwiczę a powiedz te GPIO w tym JTAG to nie aktualna sprawa ? ( mam u-boot mod)
Pytam o te szpilki bo pewnie łatwiej było by mi się podlutować..
bo diody to rozumiem, że centralnie zamiast diody wyprowadzam przewody? Mogę w ten sposób sterować masą ?

a druga sprawa - to Twój usb relay mógł bym wykorzystać do sterownia tych GPIO przez mnie zdefiniowanych ? Bo swoje USB wszystkie mam zajęte.
Jeśli tak to domyślam się, najpierw zainstalować i potem zmienić w plikach konfiguracyjnych usb relay - ustawić żądane GPIO. Ale na zrzutach ekranu tego pluginu widziałem fajne sterownie ze strony, ale ustawień czasowych tam chyba niema ?

2020-04-08 22:03:40

Witam, Gdzieś wyczytałem że WDR3600 są wolne GPIO na płycie w szpilkach JTAG. (ewentualnie GPIO diody usb) Chciałbym narazie, chociaż jednym sterować - tzn aby zawsze włączało się o danej godzinie i wyłączało też o konkretnej godzinie.
Ze względu że pisanie skryptów, to dla mnie magia (nigdy nie pisałem itp) to pomyślałem, czy nie mógł bym pozmieniać troszkę w plikach konfiguracyjnych (tylko których i co zmienić?) Aby wykorzystać w gargoyle plugin "Harmonogram WiFi" tzn WiFi mieć włączone na stałe a przez ten plugin sterować którymś GPIO?

(ps mam też zainstalowany domoticz na tym routerze ale w obecnym projekcie chcę bezpośrednio sterować przekaźnikiem tzn bez esp itp.)

Pomożecie?

2020-04-06 21:23:11

Cezary napisał/a:

Cała instrukcja to zawsze: załadować kernel i ma działać z wewnętrznego flash: https://docs.embeddedarm.com/TS-7250#Boot_Sequence
I tak chyba ci się uruchamia. Sprawdź na drugiej konsoli (wygląda na to że są dwie) co tam jest.

Co masz na myśli "druga konsola"?nie bardzo wiem jak to zrobić..
Gdzieś tam wcześniej wyczytałem że za pomocą zworki można wybrać sposób rozruchu. (chyba pierwsza zworka, której teraz niema)
z tą zworką i resztę sprawdzę przy wolne chwili.

2020-04-06 20:51:10

Cezary napisał/a:

Tak to jest bootloader. Wpisz nazwę tego sprzętu w google, w pierwszym linku który tworzysz jest link do ftp na którym są źródła do tego z 2015r. Źle nie jest.

Takie coś znalazłem
ftp://ftp.embeddedarm.com/ts-arm-sbc/ts-7250-linux

w pliku gs_tslinux.pdf zdaje się jest instrukcja jak to wgrać itp
Mógł byś rzucić okiem i naprowadzić mnie trochę, który plik i jakim sposobem, aby było najprościej ?
Dziś już nie mam sił..jutro i pojutrze też nie zapowiada się ciekawie w pracy.. Ale wciąga ciekawość i te linuksowe polecenia..
Jak mi "trochę" pomożesz to spróbuje wgrać.

2020-04-06 20:36:22

Cezary napisał/a:

Wg mnie obecnie ma cenę złomu. Pobawić się możesz a to tak jak zabawa ze sprzętem klasy linksysa wrt54gl obecnie - sztuka dla sztuki.

A to co się zgłasza teraz ten RedBoot>
to coś w rodzaju uboota (jak grub w linuxie)?

Pewnie wgrać debiana, a przede wszystkim jeszcze go znaleźć na tą maszynę, to chyba też nie taka prosta sprawa? Czy raczej z tym nie było by problemu.. Jak myślisz?

2020-04-06 17:56:38

Cezary napisał/a:

Cokolwiek powinien wypisać na konsoli. Bez konsoli nie wiele z nim zrobisz.
Niestety, to ma 200MHz i starego debiana. Uzyskanie czegoś współczesnego będzie cię kosztowało trochę pracy, o ile płytka w ogóle działa.

udało mi się zagadać z nim po com. Musiałem podpiąć com oparty na max 3232, bo dotychczasowe przejściówki nie trybiły.

Teraz daje tak

 
>> TS-NANDBOOT, Rev 1.00 - built 10:14:31, Mar  7 2005
>> Copyright (C) 2004, Technologic Systems


>> TS-BOOTROM, Rev 1.08 - built 16:18:21, Jun  5 2006
>> Copyright (C) 2006, Technologic Systems
>> TS-7250: Rev >E1 CPU, Rev B PLD, 32MB SDRAM

+Ethernet eth0: MAC address 00:d0:12:40:b8:3a
IP: 192.168.0.50/255.255.255.0, Gateway: 192.168.0.1
Default server: 192.168.0.1

RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version current-TS_5 - built 11:25:50, May  2 2007

Platform: TS-7250 Board (ARM920T) Rev A
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

RAM: 0x00000000-0x02000000, [0x00052c90-0x01ff9000] available
FLASH: 0x60000000 - 0x62000000, 2048 blocks of 0x00004000 bytes each.
== Executing boot script in 0.100 seconds - enter ^C to abort
RedBoot> fis load vmlinux
RedBoot> exec -c "console=ttyAM2,115200 root=/dev/mtdblock1"
Using base address 0x00218000 and length 0x000c0000

a jak wcisnę przy bootowaniu ^C wyskakuje znak zachęty i po wpisaniu help jest tak:

RedBoot> help
Manage aliases kept in FLASH memory
   alias name [value]
Manage machine caches
   cache [ON | OFF]
Display/switch console channel
   channel [<channel number>]
Compute a 32bit checksum [POSIX algorithm] for a range of memory
   cksum -b <location> -l <length>
Display (hex dump) a range of memory
   dump -b <location> [-l <length>] [-s] [-1|2|4]
Execute an image - with MMU off
   exec [-w timeout] [-b <load addr> [-l <length>]]
        [-r <ramdisk addr> [-s <ramdisk length>]]
        [-c "kernel command line"] [<entry_point>]
Manage FLASH images
   fis {cmds}
Manage configuration kept in FLASH memory
   fconfig [-i] [-l] [-n] [-f] [-d] | [-d] nickname [value]
Execute code at a location
   go [-w <timeout>] [-c] [-n] [entry]
Help about help?
   help [<topic>]
Display command history
   history
Set/change IP addresses
   ip_address [-l <local_ip_address>[/<mask_len>]] [-h <server_address>]
Load a file
   load [-r] [-v] [-h <host>] [-p <TCP port>][-m <varies>] [-c <channel_number>]
        [-b <base_address>] <file_name>
Compare two blocks of memory
   mcmp -s <location> -d <location> -l <length> [-1|-2|-4]
Copy memory from one address to another
   mcopy -s <location> -d <location> -l <length> [-1|-2|-4]
Fill a block of memory with a pattern
   mfill -b <location> -l <length> -p <pattern> [-1|-2|-4]
Network connectivity test
   ping [-v] [-n <count>] [-l <length>] [-t <timeout>] [-r <rate>]
        [-i <IP_addr>] -h <IP_addr>
Reset the system
   reset
Display RedBoot version information
   version
Display (hex dump) a range of memory
   x -b <location> [-l <length>] [-s] [-1|2|4]

Chciałbym się pobawić edukacyjnie - jeśli kiedyś była by chwila wolnego..
Co mógł bym z tym zrobić ? biorąc pod uwagę te parametry

200MHz ARM9 processor with MMU
2 standard serial ports with 16Byte FIFOs
Watchdog timer unit
32MB of high-speed SDRAM
32MB (128MB optional) flash disk used for RedBoot boot-loader, Linux kernel, and root file system
USB flash drive supported
10/100 Ethernet interface - autosense, LED indicators
2 USB 2.0 Compatible OHCI ports (12Mbit/s Max)
20 DIO lines - plus one output capable of switching 1 Amp at 30V
5 channel 12-bit A/D converter
PC/104 8/16 bit bus
SPI bus header
Rugged quick-release terminal strips used for power
Dimensions are 3.8 " x 4.5 " (PC/104 mounting holes)
Power requirements are 5V DC @ 400mA
Standard Operating Temperature Range: Fanless -40° to +70° full-speed; +85°C with CPU @1 66MHz
Optional Battery Backed Real Time Clock
Optional RS-485 support on COM2 (full or half duplex) with fully automatic TX enable control
Optional 8 channel 12-bit A/D converter with selectable input ranges
Optional on-board temperature sensor

Wiem że słaby procek - ale może jakies sterowanie gpio czy spi bus czy mógł bym któreś z tych interfejsów które posiada jakoś wykorzystać, choćby edukacyjnie?

jeśli jednak okazało by się nie na moje umiejętności, to czy takie coś jeszcze ktoś by zechciał kupić? Czy to po prostu już nic właściwie jest niewarte?

2020-04-05 09:31:27

Tak jak myślałem,długo nie było spokojnie.
Znowu zaczęło wyłaczać sie radio

  42.914232] eth0: link up (1000Mbps/Full duplex)
[   42.932360] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   42.970421] br-lan: port 1(eth0.1) entered blocking state
[   42.975956] br-lan: port 1(eth0.1) entered forwarding state
[   42.981805] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   43.072786] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   45.807041] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   51.087921] 3g-wan: renamed from ppp0
[   52.267851] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   98.351511] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[   98.358804]                old minutes west=0, new minutes west=-120
[  144.880775] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  144.902937] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[  144.946888] br-lan: port 2(wlan1) entered blocking state
[  144.952725] br-lan: port 2(wlan1) entered disabled state
[  144.958706] device wlan1 entered promiscuous mode
[  144.963859] br-lan: port 2(wlan1) entered blocking state
[  144.969342] br-lan: port 2(wlan1) entered forwarding state
[  145.013359] br-lan: port 3(wlan0) entered blocking state
[  145.018977] br-lan: port 3(wlan0) entered disabled state
[  145.026005] device wlan0 entered promiscuous mode
[  145.951138] br-lan: port 2(wlan1) entered disabled state
[  146.490643] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  146.497632] br-lan: port 2(wlan1) entered blocking state
[  146.503122] br-lan: port 2(wlan1) entered forwarding state
[  146.561154] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  146.568163] br-lan: port 3(wlan0) entered blocking state
[  146.573668] br-lan: port 3(wlan0) entered forwarding state
[  157.074433] device wlan0 left promiscuous mode
[  157.080766] br-lan: port 3(wlan0) entered disabled state
[  157.093689] device wlan1 left promiscuous mode
[  157.099424] br-lan: port 2(wlan1) entered disabled state
[  159.720810] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[  159.779802] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  159.841328] br-lan: port 2(wlan1) entered blocking state
[  159.846981] br-lan: port 2(wlan1) entered disabled state
[  159.853137] device wlan1 entered promiscuous mode
[  159.927522] br-lan: port 3(wlan0) entered blocking state
[  159.933412] br-lan: port 3(wlan0) entered disabled state
[  159.939493] device wlan0 entered promiscuous mode
[  159.944766] br-lan: port 3(wlan0) entered blocking state
[  159.950275] br-lan: port 3(wlan0) entered forwarding state
[  160.829722] br-lan: port 3(wlan0) entered disabled state
[  161.523050] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  161.530038] br-lan: port 2(wlan1) entered blocking state
[  161.535491] br-lan: port 2(wlan1) entered forwarding state
[  161.652605] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  161.659524] br-lan: port 3(wlan0) entered blocking state
[  161.665084] br-lan: port 3(wlan0) entered forwarding state
[  960.184984] device wlan1 left promiscuous mode
[  960.189920] br-lan: port 2(wlan1) entered disabled state
[  960.202368] device wlan0 left promiscuous mode
[  960.207266] br-lan: port 3(wlan0) entered disabled state
[  990.023202] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  990.107638] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[  990.145707] br-lan: port 2(wlan0) entered blocking state
[  990.151497] br-lan: port 2(wlan0) entered disabled state
[  990.157728] device wlan0 entered promiscuous mode
[  990.215918] br-lan: port 3(wlan1) entered blocking state
[  990.223555] br-lan: port 3(wlan1) entered disabled state
[  990.231449] device wlan1 entered promiscuous mode
[  990.238514] br-lan: port 3(wlan1) entered blocking state
[  990.244037] br-lan: port 3(wlan1) entered forwarding state
[  991.051419] br-lan: port 3(wlan1) entered disabled state
[  991.908089] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  991.915006] br-lan: port 2(wlan0) entered blocking state
[  991.920485] br-lan: port 2(wlan0) entered forwarding state
[  991.991357] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  991.998560] br-lan: port 3(wlan1) entered blocking state
[  992.004099] br-lan: port 3(wlan1) entered forwarding state
[ 1002.511564] device wlan0 left promiscuous mode
[ 1002.517566] br-lan: port 2(wlan0) entered disabled state
[ 1002.531846] device wlan1 left promiscuous mode
[ 1002.538693] br-lan: port 3(wlan1) entered disabled state
[ 1005.172458] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 1005.229127] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1005.290966] br-lan: port 2(wlan1) entered blocking state
[ 1005.296761] br-lan: port 2(wlan1) entered disabled state
[ 1005.302902] device wlan1 entered promiscuous mode
[ 1005.383834] br-lan: port 3(wlan0) entered blocking state
[ 1005.389571] br-lan: port 3(wlan0) entered disabled state
[ 1005.395619] device wlan0 entered promiscuous mode
[ 1005.400883] br-lan: port 3(wlan0) entered blocking state
[ 1005.406389] br-lan: port 3(wlan0) entered forwarding state
[ 1006.251389] br-lan: port 3(wlan0) entered disabled state
[ 1006.979330] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 1006.986326] br-lan: port 2(wlan1) entered blocking state
[ 1006.991845] br-lan: port 2(wlan1) entered forwarding state
[ 1007.103464] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1007.110498] br-lan: port 3(wlan0) entered blocking state
[ 1007.116029] br-lan: port 3(wlan0) entered forwarding state
[ 1028.955321] device wlan0 left promiscuous mode
[ 1028.960374] br-lan: port 3(wlan0) entered disabled state
[ 1028.972347] device wlan1 left promiscuous mode
[ 1028.977315] br-lan: port 2(wlan1) entered disabled state
[ 1038.761384] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1038.809913] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 1038.880488] br-lan: port 2(wlan0) entered blocking state
[ 1038.886241] br-lan: port 2(wlan0) entered disabled state
[ 1038.892666] device wlan0 entered promiscuous mode
[ 1038.930285] br-lan: port 3(wlan1) entered blocking state
[ 1038.936210] br-lan: port 3(wlan1) entered disabled state
[ 1038.942395] device wlan1 entered promiscuous mode
[ 1038.947555] br-lan: port 3(wlan1) entered blocking state
[ 1038.953075] br-lan: port 3(wlan1) entered forwarding state
[ 1039.770948] br-lan: port 3(wlan1) entered disabled state
[ 1040.600171] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1040.607020] br-lan: port 2(wlan0) entered blocking state
[ 1040.612532] br-lan: port 2(wlan0) entered forwarding state
[ 1040.663214] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 1040.670179] br-lan: port 3(wlan1) entered blocking state
[ 1040.675702] br-lan: port 3(wlan1) entered forwarding state

Jest jeszcze nadzieja aby coś zrobić bez ponwnej konfiguracji i wgrywania na nowo?

2020-04-05 08:58:04

Cezary napisał/a:

Wszystko jest dobrze z sdc1. Nie przejmuj się tymi wpisami.

No to chyba się pospieszyłem z tym że jest okej (wcześniej) nie mam internetu teraz. tzn dioda modemu świeci ciągle. Środków nie brakło (wczoraj było 65GB i nie używałem właściwie) a jedyne zmiany jakie zrobiłem to, usunąłem te pliki które wyżej wskazywałeś i zaznaczyłem w gui Polska.
Edytowałem kilkakrotnie po zmianach.

później przywróciłem kopie obrazu pendraiwa z extrootem ale usunąłem też te pliki odrazu (z usr/data/bwmon) Router się uruchomił, internet był.
Ale zauważyłem że przerywa połączenie z WiFi taj jak by się wyłączało radio (diody na chwilę od radia gasły) i za chwile wifi znowu było.
tu log z tego rozłączania - końcowa część logu

  
 864.577983] 
[  864.579501] ---[ end trace d2d374dce5b9fcee ]---
[  870.663794] device wlan1 left promiscuous mode
[  870.668587] br-lan: port 2(wlan1) entered disabled state
[  870.680337] device wlan0 left promiscuous mode
[  870.685211] br-lan: port 3(wlan0) entered disabled state
[  899.853719] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  899.887380] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[  899.920750] br-lan: port 2(wlan0) entered blocking state
[  899.926316] br-lan: port 2(wlan0) entered disabled state
[  899.932266] device wlan0 entered promiscuous mode
[  899.959949] br-lan: port 3(wlan1) entered blocking state
[  899.965417] br-lan: port 3(wlan1) entered disabled state
[  899.971424] device wlan1 entered promiscuous mode
[  899.976381] br-lan: port 3(wlan1) entered blocking state
[  899.981839] br-lan: port 3(wlan1) entered forwarding state
[  900.912120] br-lan: port 3(wlan1) entered disabled state
[  901.558747] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  901.565494] br-lan: port 2(wlan0) entered blocking state
[  901.570897] br-lan: port 2(wlan0) entered forwarding state
[  901.665683] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  901.672422] br-lan: port 3(wlan1) entered blocking state
[  901.677825] br-lan: port 3(wlan1) entered forwarding state
[  904.112100] usb 1-1.1: new high-speed USB device number 8 using ehci-platform
[  904.299794] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:0766)
[  904.334396] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platform/usb1/1-1/1-1.1/1-1.1:1.0/input/input1
[  912.122843] device wlan0 left promiscuous mode
[  912.127829] br-lan: port 2(wlan0) entered disabled state
[  912.144655] device wlan1 left promiscuous mode
[  912.149530] br-lan: port 3(wlan1) entered disabled state
[  914.742310] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[  914.809573] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  914.841372] br-lan: port 2(wlan1) entered blocking state
[  914.847119] br-lan: port 2(wlan1) entered disabled state
[  914.853117] device wlan1 entered promiscuous mode
[  914.929542] br-lan: port 3(wlan0) entered blocking state
[  914.935426] br-lan: port 3(wlan0) entered disabled state
[  914.941472] device wlan0 entered promiscuous mode
[  914.946804] br-lan: port 3(wlan0) entered blocking state
[  914.952328] br-lan: port 3(wlan0) entered forwarding state
[  915.792046] br-lan: port 3(wlan0) entered disabled state
[  916.504194] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  916.511090] br-lan: port 2(wlan1) entered blocking state
[  916.516597] br-lan: port 2(wlan1) entered forwarding state
[  916.617886] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  916.625489] br-lan: port 3(wlan0) entered blocking state
[  916.630964] br-lan: port 3(wlan0) entered forwarding state

------------------------------------------------------------------

  864.577983] 
[  864.579501] ---[ end trace d2d374dce5b9fcee ]---
[  870.663794] device wlan1 left promiscuous mode
[  870.668587] br-lan: port 2(wlan1) entered disabled state
[  870.680337] device wlan0 left promiscuous mode
[  870.685211] br-lan: port 3(wlan0) entered disabled state
[  899.853719] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  899.887380] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[  899.920750] br-lan: port 2(wlan0) entered blocking state
[  899.926316] br-lan: port 2(wlan0) entered disabled state
[  899.932266] device wlan0 entered promiscuous mode
[  899.959949] br-lan: port 3(wlan1) entered blocking state
[  899.965417] br-lan: port 3(wlan1) entered disabled state
[  899.971424] device wlan1 entered promiscuous mode
[  899.976381] br-lan: port 3(wlan1) entered blocking state
[  899.981839] br-lan: port 3(wlan1) entered forwarding state
[  900.912120] br-lan: port 3(wlan1) entered disabled state
[  901.558747] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  901.565494] br-lan: port 2(wlan0) entered blocking state
[  901.570897] br-lan: port 2(wlan0) entered forwarding state
[  901.665683] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  901.672422] br-lan: port 3(wlan1) entered blocking state
[  901.677825] br-lan: port 3(wlan1) entered forwarding state
[  904.112100] usb 1-1.1: new high-speed USB device number 8 using ehci-platform
[  904.299794] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:0766)
[  904.334396] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platform/usb1/1-1/1-1.1/1-1.1:1.0/input/input1
[  912.122843] device wlan0 left promiscuous mode
[  912.127829] br-lan: port 2(wlan0) entered disabled state
[  912.144655] device wlan1 left promiscuous mode
[  912.149530] br-lan: port 3(wlan1) entered disabled state
[  914.742310] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[  914.809573] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  914.841372] br-lan: port 2(wlan1) entered blocking state
[  914.847119] br-lan: port 2(wlan1) entered disabled state
[  914.853117] device wlan1 entered promiscuous mode
[  914.929542] br-lan: port 3(wlan0) entered blocking state
[  914.935426] br-lan: port 3(wlan0) entered disabled state
[  914.941472] device wlan0 entered promiscuous mode
[  914.946804] br-lan: port 3(wlan0) entered blocking state
[  914.952328] br-lan: port 3(wlan0) entered forwarding state
[  915.792046] br-lan: port 3(wlan0) entered disabled state
[  916.504194] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  916.511090] br-lan: port 2(wlan1) entered blocking state
[  916.516597] br-lan: port 2(wlan1) entered forwarding state
[  916.617886] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  916.625489] br-lan: port 3(wlan0) entered blocking state
[  916.630964] br-lan: port 3(wlan0) entered forwarding state
[ 2607.520599] device wlan1 left promiscuous mode
[ 2607.525540] br-lan: port 2(wlan1) entered disabled state
[ 2607.537870] device wlan0 left promiscuous mode
[ 2607.542775] br-lan: port 3(wlan0) entered disabled state
[ 2610.099152] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2610.176899] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2610.240483] br-lan: port 2(wlan0) entered blocking state
[ 2610.246278] br-lan: port 2(wlan0) entered disabled state
[ 2610.252396] device wlan0 entered promiscuous mode
[ 2610.273248] br-lan: port 3(wlan1) entered blocking state
[ 2610.278990] br-lan: port 3(wlan1) entered disabled state
[ 2610.285041] device wlan1 entered promiscuous mode
[ 2610.290168] br-lan: port 3(wlan1) entered blocking state
[ 2610.295623] br-lan: port 3(wlan1) entered forwarding state
[ 2611.126221] br-lan: port 3(wlan1) entered disabled state
[ 2611.901574] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2611.908521] br-lan: port 2(wlan0) entered blocking state
[ 2611.913988] br-lan: port 2(wlan0) entered forwarding state
[ 2611.954830] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2611.961739] br-lan: port 3(wlan1) entered blocking state
[ 2611.967256] br-lan: port 3(wlan1) entered forwarding state
[ 2622.331410] device wlan1 left promiscuous mode
[ 2622.336288] br-lan: port 3(wlan1) entered disabled state
[ 2622.343867] device wlan0 left promiscuous mode
[ 2622.349126] br-lan: port 2(wlan0) entered disabled state
[ 2624.318715] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2624.351387] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2624.445871] br-lan: port 2(wlan0) entered blocking state
[ 2624.451617] br-lan: port 2(wlan0) entered disabled state
[ 2624.457722] device wlan0 entered promiscuous mode
[ 2624.462975] br-lan: port 2(wlan0) entered blocking state
[ 2624.468476] br-lan: port 2(wlan0) entered forwarding state
[ 2624.474587] br-lan: port 2(wlan0) entered disabled state
[ 2624.500827] br-lan: port 3(wlan1) entered blocking state
[ 2624.507099] br-lan: port 3(wlan1) entered disabled state
[ 2624.513062] device wlan1 entered promiscuous mode
[ 2626.101808] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2626.108837] br-lan: port 2(wlan0) entered blocking state
[ 2626.114296] br-lan: port 2(wlan0) entered forwarding state
[ 2626.155291] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2626.162203] br-lan: port 3(wlan1) entered blocking state
[ 2626.167698] br-lan: port 3(wlan1) entered forwarding state
[ 2633.456976] device wlan1 left promiscuous mode
[ 2633.461828] br-lan: port 3(wlan1) entered disabled state
[ 2633.479350] device wlan0 left promiscuous mode
[ 2633.484231] br-lan: port 2(wlan0) entered disabled state
[ 2636.071230] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2636.127497] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2636.188518] br-lan: port 2(wlan1) entered blocking state
[ 2636.194215] br-lan: port 2(wlan1) entered disabled state
[ 2636.201896] device wlan1 entered promiscuous mode
[ 2636.209029] br-lan: port 2(wlan1) entered blocking state
[ 2636.214531] br-lan: port 2(wlan1) entered forwarding state
[ 2636.231321] br-lan: port 3(wlan0) entered blocking state
[ 2636.236972] br-lan: port 3(wlan0) entered disabled state
[ 2636.243023] device wlan0 entered promiscuous mode
[ 2637.126149] br-lan: port 2(wlan1) entered disabled state
[ 2637.500864] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2637.507881] br-lan: port 3(wlan0) entered blocking state
[ 2637.513367] br-lan: port 3(wlan0) entered forwarding state
[ 2637.602312] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2637.609331] br-lan: port 2(wlan1) entered blocking state
[ 2637.614788] br-lan: port 2(wlan1) entered forwarding state
[ 2648.046253] device wlan0 left promiscuous mode
[ 2648.051211] br-lan: port 3(wlan0) entered disabled state
[ 2648.071076] device wlan1 left promiscuous mode
[ 2648.075886] br-lan: port 2(wlan1) entered disabled state
[ 2650.250321] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2650.392214] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2650.405820] br-lan: port 2(wlan0) entered blocking state
[ 2650.411581] br-lan: port 2(wlan0) entered disabled state
[ 2650.417570] device wlan0 entered promiscuous mode
[ 2650.481409] br-lan: port 3(wlan1) entered blocking state
[ 2650.487237] br-lan: port 3(wlan1) entered disabled state
[ 2650.493234] device wlan1 entered promiscuous mode
[ 2650.498371] br-lan: port 3(wlan1) entered blocking state
[ 2650.503861] br-lan: port 3(wlan1) entered forwarding state
[ 2651.286097] br-lan: port 3(wlan1) entered disabled state
[ 2651.845642] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2651.852589] br-lan: port 2(wlan0) entered blocking state
[ 2651.858080] br-lan: port 2(wlan0) entered forwarding state
[ 2651.921342] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2651.930219] br-lan: port 3(wlan1) entered blocking state
[ 2651.935689] br-lan: port 3(wlan1) entered forwarding state
[ 2704.431482] device wlan1 left promiscuous mode
[ 2704.436386] br-lan: port 3(wlan1) entered disabled state
[ 2704.448865] device wlan0 left promiscuous mode
[ 2704.453769] br-lan: port 2(wlan0) entered disabled state
[ 2754.549678] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2754.618876] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2754.639241] br-lan: port 2(wlan0) entered blocking state
[ 2754.644981] br-lan: port 2(wlan0) entered disabled state
[ 2754.651053] device wlan0 entered promiscuous mode
[ 2754.671362] br-lan: port 3(wlan1) entered blocking state
[ 2754.677006] br-lan: port 3(wlan1) entered disabled state
[ 2754.683358] device wlan1 entered promiscuous mode
[ 2754.689393] br-lan: port 3(wlan1) entered blocking state
[ 2754.694894] br-lan: port 3(wlan1) entered forwarding state
[ 2755.604659] br-lan: port 3(wlan1) entered disabled state
[ 2756.514748] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2756.521581] br-lan: port 2(wlan0) entered blocking state
[ 2756.527104] br-lan: port 2(wlan0) entered forwarding state
[ 2756.584661] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2756.591716] br-lan: port 3(wlan1) entered blocking state
[ 2756.597245] br-lan: port 3(wlan1) entered forwarding state
[ 2757.973878] device wlan1 left promiscuous mode
[ 2757.978900] br-lan: port 3(wlan1) entered disabled state
[ 2757.989421] device wlan0 left promiscuous mode
[ 2757.994269] br-lan: port 2(wlan0) entered disabled state
[ 2760.835395] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2760.895165] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2760.962942] br-lan: port 2(wlan1) entered blocking state
[ 2760.968609] br-lan: port 2(wlan1) entered disabled state
[ 2760.974856] device wlan1 entered promiscuous mode
[ 2760.979905] br-lan: port 2(wlan1) entered blocking state
[ 2760.985430] br-lan: port 2(wlan1) entered forwarding state
[ 2761.020065] br-lan: port 3(wlan0) entered blocking state
[ 2761.025718] br-lan: port 3(wlan0) entered disabled state
[ 2761.031910] device wlan0 entered promiscuous mode
[ 2761.844461] br-lan: port 2(wlan1) entered disabled state
[ 2763.004868] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2763.011779] br-lan: port 2(wlan1) entered blocking state
[ 2763.017289] br-lan: port 2(wlan1) entered forwarding state
[ 2763.061901] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2763.068978] br-lan: port 3(wlan0) entered blocking state
[ 2763.074511] br-lan: port 3(wlan0) entered forwarding state
[ 2770.214688] device wlan1 left promiscuous mode
[ 2770.219483] br-lan: port 2(wlan1) entered disabled state
[ 2770.241721] device wlan0 left promiscuous mode
[ 2770.246879] br-lan: port 3(wlan0) entered disabled state
[ 2773.515118] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2773.624465] br-lan: port 2(wlan0) entered blocking state
[ 2773.630161] br-lan: port 2(wlan0) entered disabled state
[ 2773.636274] device wlan0 entered promiscuous mode
[ 2773.670186] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2773.762635] br-lan: port 3(wlan1) entered blocking state
[ 2773.768262] br-lan: port 3(wlan1) entered disabled state
[ 2773.774394] device wlan1 entered promiscuous mode
[ 2773.779528] br-lan: port 3(wlan1) entered blocking state
[ 2773.785056] br-lan: port 3(wlan1) entered forwarding state
[ 2774.563529] br-lan: port 3(wlan1) entered disabled state
[ 2775.252286] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2775.259308] br-lan: port 2(wlan0) entered blocking state
[ 2775.264829] br-lan: port 2(wlan0) entered forwarding state
[ 2775.370724] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2775.377618] br-lan: port 3(wlan1) entered blocking state
[ 2775.383093] br-lan: port 3(wlan1) entered forwarding state
[ 2785.653479] device wlan0 left promiscuous mode
[ 2785.658295] br-lan: port 2(wlan0) entered disabled state
[ 2785.689620] device wlan1 left promiscuous mode
[ 2785.694652] br-lan: port 3(wlan1) entered disabled state
[ 2787.677408] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2787.752846] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 2787.796599] br-lan: port 2(wlan0) entered blocking state
[ 2787.802258] br-lan: port 2(wlan0) entered disabled state
[ 2787.808440] device wlan0 entered promiscuous mode
[ 2787.836774] br-lan: port 3(wlan1) entered blocking state
[ 2787.842407] br-lan: port 3(wlan1) entered disabled state
[ 2787.848645] device wlan1 entered promiscuous mode
[ 2787.853766] br-lan: port 3(wlan1) entered blocking state
[ 2787.859260] br-lan: port 3(wlan1) entered forwarding state
[ 2788.802731] br-lan: port 3(wlan1) entered disabled state
[ 2789.323385] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2789.330170] br-lan: port 2(wlan0) entered blocking state
[ 2789.335694] br-lan: port 2(wlan0) entered forwarding state
[ 2789.400084] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2789.407095] br-lan: port 3(wlan1) entered blocking state
[ 2789.412559] br-lan: port 3(wlan1) entered forwarding state

Więc dziś rano przywróciłem znowu te pliki (miałem ich kopie) i narazie działa nic nie resetuje. Ale mam wrażenie że to jakiś przypadek że jeszcze nie resetuje. Obecnie jest tak jak po kopi obrazu pendraiwa, Ale wiem że wcześniej też zdarzały się resety.

teraz wygląda to tek

                                                                                 
Booting image from 0x9F020000...                                                
                                                                                
   Vendor/image name:    OpenWrt r7935-d08a63770c                               
   Hardware ID:          0x36000001                                             
   Whole image size:     7.8 MB (8126464 bytes)                                 
   Kernel size:          1.3 MB (1385806 bytes)                                 
   Rootfs size:          5.7 MB (5958384 bytes)                                 
   Kernel load address:  0x80060000                                             
   Kernel entry point:   0x80060000                                             
                                                                                
   Header CRC...  skipped                                                       
   Data CRC...    skipped                                                       
                                                                                
Stopping network... OK!                                                         
Uncompressing Kernel... OK!                                                     
Starting kernel...                                                              
                                                                                
[    0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (Op9
[    0.000000] bootconsole [early0] enabled                                     
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)                           
[    0.000000] SoC: Atheros AR9344 rev 2                                        
[    0.000000] Determined physical RAM map:                                     
[    0.000000]  memory: 08000000 @ 00000000 (usable)                            
[    0.000000] Initrd not found or empty - disabling initrd                     
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.  
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32s
[    0.000000] Zone ranges:                                                     
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]           
[    0.000000] Movable zone start for each node                                 
[    0.000000] Early memory node ranges                                         
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]          
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pa2
[    0.000000] Kernel command line:  board=TL-WDR4300  console=ttyS0,115200 rood
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)              
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)   
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)     
[    0.000000] Writing ErrCtl register=00000000                                 
[    0.000000] Readback ErrCtl register=00000000                                
[    0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdat)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1       
[    0.000000] NR_IRQS:51                                                       
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.0z
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_s
[    0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809s
[    0.008721] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)          
[    0.081683] pid_max: default: 32768 minimum: 301                             
[    0.086951] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)      
[    0.094340] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) 
[    0.105224] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
[    0.116230] futex hash table entries: 256 (order: -1, 3072 bytes)            
[    0.124381] NET: Registered protocol family 16                               
[    0.130970] MIPS: machine is TP-LINK TL-WDR3600/4300/4310                    
[    0.140734] registering PCI controller with io_map_base unset                
[    0.396064] PCI host bridge to bus 0000:00                                   
[    0.400699] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]   
[    0.408362] pci_bus 0000:00: root bus resource [io  0x0000]                  
[    0.414588] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]    
[    0.422153] pci_bus 0000:00: No busn resource found for root bus, will use []
[    0.431042] pci 0000:00:00.0: invalid calibration data                       
[    0.437223] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64b]
[    0.445431] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pre]
[    0.453491] pci 0000:00:00.0: using irq 40 for pin 1                         
[    0.462679] clocksource: Switched to clocksource MIPS                        
[    0.469511] NET: Registered protocol family 2                                
[    0.475411] TCP established hash table entries: 1024 (order: 0, 4096 bytes)  
[    0.483251] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)         
[    0.490350] TCP: Hash tables configured (established 1024 bind 1024)         
[    0.497536] UDP hash table entries: 256 (order: 0, 4096 bytes)               
[    0.504104] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)          
[    0.511357] NET: Registered protocol family 1                                
[    0.519438] Crashlog allocated RAM at address 0x3f00000                      
[    0.526547] workingset: timestamp_bits=30 max_order=15 bucket_order=0        
[    0.541135] squashfs: version 4.0 (2009/01/31) Phillip Lougher               
[    0.547681] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORI.
[    0.569051] io scheduler noop registered                                     
[    0.573478] io scheduler deadline registered (default)                       
[    0.579673] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled         
[    0.589709] console [ttyS0] disabled                                         
[    0.613805] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 25A
[    0.623443] console [ttyS0] enabled                                          
[    0.623443] console [ttyS0] enabled                                          
[    0.630857] bootconsole [early0] disabled                                    
[    0.630857] bootconsole [early0] disabled                                    
[    0.646123] m25p80 spi0.0: found w25q128, expected m25p80                    
[    0.660756] m25p80 spi0.0: w25q128 (16384 Kbytes)                            
[    0.665904] 5 tp-link partitions found on MTD device spi0.0                  
[    0.671558] Creating 5 MTD partitions on "spi0.0":                           
[    0.676460] 0x000000000000-0x000000020000 : "u-boot"                         
[    0.683647] 0x000000020000-0x000000172750 : "kernel"                         
[    0.690884] 0x000000172750-0x000000ff0000 : "rootfs"                         
[    0.697737] mtd: device 2 (rootfs) set to be root filesystem                 
[    0.703574] 1 squashfs-split partitions found on MTD device rootfs           
[    0.709849] 0x000000730000-0x000000ff0000 : "rootfs_data"                    
[    0.717715] 0x000000ff0000-0x000001000000 : "art"                            
[    0.724788] 0x000000020000-0x000000ff0000 : "firmware"                       
[    0.733390] libphy: Fixed MDIO Bus: probed                                   
[    0.748891] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.415836] libphy: ag71xx_mdio: probed                                      
[    2.044084] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd]
[    2.055655] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII            
[    2.064144] NET: Registered protocol family 10                               
[    2.073174] NET: Registered protocol family 17                               
[    2.077747] bridge: filtering via arp/ip/ip6tables is no longer available by.
[    2.091041] 8021q: 802.1Q VLAN Support v1.8                                  
[    2.097309] hctosys: unable to open rtc device (rtc0)                        
[    2.106208] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. 
[    2.115062] Freeing unused kernel memory: 308K                               
[    2.119571] This architecture does not have kernel memory protection.        
[    2.562699] random: fast init done                                           
[    2.791358] init: Console is alive                                           
[    2.795108] init: - watchdog -                                               
[    5.115486] kmodloader: loading kernel modules from /etc/modules-boot.d/*    
[    5.400949] usbcore: registered new interface driver usbfs                   
[    5.406681] usbcore: registered new interface driver hub                     
[    5.412187] usbcore: registered new device driver usb                        
[    5.456240] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver       
[    5.472855] SCSI subsystem initialized                                       
[    5.482577] ehci-platform: EHCI generic platform driver                      
[    5.488044] ehci-platform ehci-platform: EHCI Host Controller                
[    5.493937] ehci-platform ehci-platform: new USB bus registered, assigned bu1
[    5.504088] ehci-platform ehci-platform: irq 3, io mem 0x1b000000            
[    5.532776] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00          
[    5.540099] hub 1-0:1.0: USB hub found                                       
[    5.544372] hub 1-0:1.0: 1 port detected                                     
[    5.553779] usbcore: registered new interface driver usb-storage             
[    5.569238] usbcore: registered new interface driver uas                     
[    5.575527] kmodloader: done loading kernel modules from /etc/modules-boot.d*
[    5.585348] init: - preinit -                                                
[    6.105554] usb 1-1: new high-speed USB device number 2 using ehci-platform  
[    6.306852] hub 1-1:1.0: USB hub found                                       
[    6.385687] hub 1-1:1.0: 4 ports detected                                    
[    6.467790] random: procd: uninitialized urandom read (4 bytes read)         
[    6.766401] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready               
Press the [f] key and hit [enter] to enter fails[    6.842769] usb 1-1.1: new hm
afe mode                                                                        
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level    
[    7.122699] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[    7.289511] usb-storage 1-1.2:1.0: USB Mass Storage device detected          
[    7.296853] scsi host0: usb-storage 1-1.2:1.0                                
[    7.402703] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[    7.558193] usb-storage 1-1.3:1.0: USB Mass Storage device detected          
[    7.566011] usb-storage 1-1.3:1.1: USB Mass Storage device detected          
[    7.573762] usb-storage 1-1.3:1.2: USB Mass Storage device detected          
[    7.581449] usb-storage 1-1.3:1.3: USB Mass Storage device detected          
[    7.589231] usb-storage 1-1.3:1.4: USB Mass Storage device detected          
[    7.596965] usb-storage 1-1.3:1.5: USB Mass Storage device detected          
[    7.604570] scsi host1: usb-storage 1-1.3:1.5                                
[    7.609863] usb-storage 1-1.3:1.6: USB Mass Storage device detected          
[    7.619816] scsi host2: usb-storage 1-1.3:1.6                                
[    7.722698] usb 1-1.4: new high-speed USB device number 6 using ehci-platform
[    7.793938] eth0: link up (1000Mbps/Full duplex)                             
[    7.798709] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready          
[    8.674630] scsi 2:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 P2
[    8.685021] scsi 1:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 P2
[    8.697214] sd 2:0:0:0: [sda] Attached SCSI removable disk                   
[    8.976538] usb-storage 1-1.4:1.0: USB Mass Storage device detected          
[    8.983836] scsi host3: usb-storage 1-1.4:1.0                                
[   10.039415] mount_root: loading kmods from internal overlay                  
[   10.046174] scsi 3:0:0:0: Direct-Access     ADATA    USB Flash Drive  1100 PS
[   10.057647] sd 3:0:0:0: [sdb] 7925760 512-byte logical blocks: (4.06 GB/3.78)
[   10.072967] sd 3:0:0:0: [sdb] Write Protect is off                           
[   10.092806] sd 3:0:0:0: [sdb] No Caching mode page found                     
[   10.098214] sd 3:0:0:0: [sdb] Assuming drive cache: write through            
[   10.118128]  sdb: sdb1 sdb2                                                  
[   10.135443] sd 3:0:0:0: [sdb] Attached SCSI removable disk                   
[   10.186113] kmodloader: loading kernel modules from //etc/modules-boot.d/*   
[   10.202017] kmodloader: done loading kernel modules from //etc/modules-boot.*
[   10.941000] scsi 0:0:0:0: Direct-Access     Wilk     USB DISK 2.0     PMAP P6
[   10.955847] sd 0:0:0:0: [sdc] 30322688 512-byte logical blocks: (15.5 GB/14.)
[   10.967643] sd 0:0:0:0: [sdc] Write Protect is off                           
[   10.974652] sd 0:0:0:0: [sdc] No Caching mode page found                     
[   10.980119] sd 0:0:0:0: [sdc] Assuming drive cache: write through            
[   11.000171]  sdc: sdc1                                                       
[   11.011152] sd 0:0:0:0: [sdc] Attached SCSI removable disk                   
[   11.206797] jffs2: notice: (552) jffs2_build_xattr_subsystem: complete build.
[   11.223051] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab   
/dev/sdb1: recovering journal                                                   
/dev/sdb1: clean, 2572/185840 files, 40559/742784 blocks                        
[   11.922585] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: 
[   12.030034] mount_root: switched to extroot                                  
[   12.039030] urandom-seed: Seeding with /etc/urandom.seed                     
[   12.202300] eth0: link down                                                  
[   12.219221] procd: - early -                                                 
[   12.222251] procd: - watchdog -                                              
[   12.886107] procd: - watchdog -                                              
[   12.889553] procd: - ubus -                                                  
[   13.282018] random: ubusd: uninitialized urandom read (4 bytes read)         
[   13.300514] random: ubusd: uninitialized urandom read (4 bytes read)         
[   13.311106] random: jshn: uninitialized urandom read (4 bytes read)          
[   13.319223] procd: - init -                                                  
Please press Enter to activate this console.                                    
[   14.902614] kmodloader: loading kernel modules from /etc/modules.d/*         
[   15.075282] Key type dns_resolver registered                                 
[   15.109764] RPC: Registered named UNIX socket transport module.              
[   15.115831] RPC: Registered udp transport module.                            
[   15.120603] RPC: Registered tcp transport module.                            
[   15.125388] RPC: Registered tcp NFSv4.1 backchannel transport module.        
[   15.150344] tun: Universal TUN/TAP device driver, 1.6                        
[   15.155550] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>           
[   15.178953] gre: GRE over IPv4 demultiplexor driver                          
[   15.186729] ip_gre: GRE over IPv4 tunneling driver                           
[   15.232612] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).         
[   15.260783] i2c /dev entries driver                                          
[   15.280545] Linux video capture interface: v2.00                             
[   15.318496] u32 classifier                                                   
[   15.321279]     input device check on                                        
[   15.325028]     Actions configured                                           
[   15.332199] Mirror/redirect action on                                        
[   15.382494] fuse init (API version 7.26)                                     
[   15.448328] usbcore: registered new interface driver cdc_acm                 
[   15.454160] cdc_acm: USB Abstract Control Model driver for USB modems and ISs
[   15.510297] usbcore: registered new interface driver cdc_wdm                 
[   15.542895] Loading modules backported from Linux version wt-2017-11-01-0-gf0
[   15.551020] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d     
[   15.602418] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1          
[   15.609029] usbcore: registered new interface driver cpia2                   
[   15.660524] Ebtables v2.0 registered                                         
[   15.692820] ip_tables: (C) 2000-2006 Netfilter Core Team                     
[   15.733550] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)              
[   16.356686] usbcore: registered new interface driver ums-alauda              
[   16.379166] usbcore: registered new interface driver ums-cypress             
[   16.404562] usbcore: registered new interface driver ums-datafab             
[   16.442646] usbcore: registered new interface driver ums-freecom             
[   16.478485] usbcore: registered new interface driver ums-isd200              
[   16.505951] usbcore: registered new interface driver ums-jumpshot            
[   16.525487] usbcore: registered new interface driver ums-karma               
[   16.537258] usbcore: registered new interface driver ums-sddr09              
[   16.557283] usbcore: registered new interface driver ums-sddr55              
[   16.586709] usbcore: registered new interface driver ums-usbat               
[   16.626946] usbcore: registered new interface driver usblp                   
[   16.752911] usbcore: registered new interface driver usbserial               
[   16.758941] usbcore: registered new interface driver usbserial_generic       
[   16.765723] usbserial: USB Serial support registered for generic             
[   17.097479] xt_time: kernel timezone is -0000                                
[   17.114789] cdc_ether 1-1.3:1.1 wwan0: register 'cdc_ether' at usb-ehci-plat0
[   17.127485] usbcore: registered new interface driver cdc_ether               
[   17.162161] usbcore: registered new interface driver cdc_ncm                 
[   17.287717] gspca_main: v2.14.0 registered                                   
[   17.312480] usbcore: registered new interface driver mars                    
[   17.332369] usbcore: registered new interface driver mr97310a                
[   17.352638] usbcore: registered new interface driver ov519                   
[   17.375897] usbcore: registered new interface driver ov534                   
[   17.398547] usbcore: registered new interface driver ov534_9                 
[   17.413198] usbcore: registered new interface driver pac207                  
[   17.435843] usbcore: registered new interface driver pac7311                 
[   17.456035] usbcore: registered new interface driver se401                   
[   17.470884] usbcore: registered new interface driver gspca_sn9c20x           
[   17.489689] usbcore: registered new interface driver sonixb                  
[   17.510963] usbcore: registered new interface driver sonixj                  
[   17.555737] usbcore: registered new interface driver spca500                 
[   17.585439] usbcore: registered new interface driver spca501                 
[   17.605326] usbcore: registered new interface driver spca506                 
[   17.625271] usbcore: registered new interface driver spca508                 
[   17.655806] usbcore: registered new interface driver spca561                 
[   17.675141] usbcore: registered new interface driver sq905                   
[   17.701199] usbcore: registered new interface driver sq905c                  
[   17.745194] usbcore: registered new interface driver stk014                  
[   17.773768] usbcore: registered new interface driver STV06xx                 
[   17.795847] usbcore: registered new interface driver sunplus                 
[   17.816315] usbcore: registered new interface driver t613                    
[   17.829256] usbcore: registered new interface driver tv8532                  
[   17.848382] usbcore: registered new interface driver vc032x                  
[   17.879140] usbcore: registered new interface driver gspca_zc3xx             
[   17.930430] usbcore: registered new interface driver huawei_cdc_ncm          
[   18.339467] PPP generic driver version 2.4.2                                 
[   18.355420] NET: Registered protocol family 24                               
[   18.374700] PPTP driver version 0.8.5                                        
[   18.392406] usbcore: registered new interface driver Philips webcam          
[   18.424173] usbcore: registered new interface driver qmi_wwan                
[   18.446818] usbcore: registered new interface driver rndis_host              
[   18.467615] usbcore: registered new interface driver sierra                  
[   18.473457] usbserial: USB Serial support registered for Sierra USB modem    
[   18.506577] usbcore: registered new interface driver sierra_net              
[   18.555521] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:0)
[   18.593443] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platfo0
[   18.604418] usbcore: registered new interface driver uvcvideo                
[   18.610252] USB Video Class driver (1.1.1)                                   
[   18.750272] usbcore: registered new interface driver cdc_mbim                
[   18.768660] usbcore: registered new interface driver conex                   
[   18.788813] usbcore: registered new interface driver etoms                   
[   18.825756] usbcore: registered new interface driver finepix                 
[   18.857334] usbcore: registered new interface driver gspca_gl860             
[   18.886495] usbcore: registered new interface driver jeilinj                 
[   18.917307] usbcore: registered new interface driver konica                  
[   18.948238] usbcore: registered new interface driver ALi m5602               
[   18.981255] usbcore: registered new interface driver option                  
[   18.987097] usbserial: USB Serial support registered for GSM modem (1-port)  
[   18.995046] option 1-1.3:1.0: GSM modem (1-port) converter detected          
[   19.001714] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB0  
[   19.009293] option 1-1.3:1.3: GSM modem (1-port) converter detected          
[   19.015995] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB1  
[   19.023159] option 1-1.3:1.4: GSM modem (1-port) converter detected          
[   19.029837] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB2  
[   19.134601] usbcore: registered new interface driver qcserial                
[   19.140558] usbserial: USB Serial support registered for Qualcomm USB modem  
[   19.257159] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47      
[   19.264117] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)                 
[   19.289519] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40      
[   19.593499] kmodloader: done loading kernel modules from /etc/modules.d/*    
[   26.989905] random: crng init done                                           
[   26.993375] random: 6 urandom warning(s) missed due to ratelimiting          
[   32.294358] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:)
[   35.178366] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:)
[   38.268245] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:)
[   40.008371] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:)
[   41.758388] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:)
[   41.890751] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready               
[   41.912773] br-lan: port 1(eth0.1) entered blocking state                    
[   41.918266] br-lan: port 1(eth0.1) entered disabled state                    
[   41.924194] device eth0.1 entered promiscuous mode                           
[   41.929067] device eth0 entered promiscuous mode                             
[   41.964091] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready             
[   42.035897] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready             
[   42.914233] eth0: link up (1000Mbps/Full duplex)                             
[   42.919029] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready          
[   43.002849] br-lan: port 1(eth0.1) entered blocking state                    
[   43.008345] br-lan: port 1(eth0.1) entered forwarding state                  
[   43.014215] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready        
[   43.112986] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready        
[   46.633118] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:)
[   48.089226] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready              
[   48.215370] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready              
[   48.308501] br-lan: port 2(wlan0) entered blocking state                     
[   48.313959] br-lan: port 2(wlan0) entered disabled state                     
[   48.319835] device wlan0 entered promiscuous mode                            
[   48.349358] br-lan: port 3(wlan1) entered blocking state                     
[   48.354915] br-lan: port 3(wlan1) entered disabled state                     
[   48.360753] device wlan1 entered promiscuous mode                            
[   48.365677] br-lan: port 3(wlan1) entered blocking state                     
[   48.371097] br-lan: port 3(wlan1) entered forwarding state                   
[   49.509091] br-lan: port 3(wlan1) entered disabled state                     
[   51.793032] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready         
[   51.799729] br-lan: port 2(wlan0) entered blocking state                     
[   51.805196] br-lan: port 2(wlan0) entered forwarding state                   
[   51.904265] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready         
[   51.911017] br-lan: port 3(wlan1) entered blocking state                     
[   51.916502] br-lan: port 3(wlan1) entered forwarding state                   
[   54.007635] 3g-wan: renamed from ppp0                                        
[   55.808463] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:)
[   98.635169] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting 
[   98.642482]                old minutes west=0, new minutes west=-120

2020-04-04 22:48:03

Cezary napisał/a:

Usuń dane z katalogu usr/data/bwmon na pendrivie z extroota.

usunąłem narazie działa na extroocie bez resetów..
teraz wygląda to tak - w międzyczasie zmieniłem w gui Kraj na Poland, bo nie było tam nic ustawione i chciałem ustawić modem na jakieś stałe usb, ale on chyba robi to automatycznie (teraz jest usb0)

Booting image from 0x9F020000...

   Vendor/image name:    OpenWrt r7935-d08a63770c
   Hardware ID:          0x36000001
   Whole image size:     7.8 MB (8126464 bytes)
   Kernel size:          1.3 MB (1385806 bytes)
   Rootfs size:          5.7 MB (5958384 bytes)
   Kernel load address:  0x80060000
   Kernel entry point:   0x80060000

   Header CRC...  skipped
   Data CRC...    skipped

Stopping network... OK!
Uncompressing Kernel... OK!
Starting kernel...

[    0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7865-5880dd48d5) ) #0 Wed Dec 11 21:46:13 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=TL-WDR4300  console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata, 448K rodata, 308K init, 211K bss, 6132K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6950037990 ns
[    0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809031678ns
[    0.008721] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)
[    0.081683] pid_max: default: 32768 minimum: 301
[    0.086951] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094340] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.105231] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.116239] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.124391] NET: Registered protocol family 16
[    0.130978] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[    0.140745] registering PCI controller with io_map_base unset
[    0.396050] PCI host bridge to bus 0000:00
[    0.400682] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.408345] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.414562] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.422127] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.431016] pci 0000:00:00.0: invalid calibration data
[    0.437199] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[    0.445405] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[    0.453464] pci 0000:00:00.0: using irq 40 for pin 1
[    0.462658] clocksource: Switched to clocksource MIPS
[    0.469499] NET: Registered protocol family 2
[    0.475402] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.483242] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.490341] TCP: Hash tables configured (established 1024 bind 1024)
[    0.497526] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.504086] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.511339] NET: Registered protocol family 1
[    0.519418] Crashlog allocated RAM at address 0x3f00000
[    0.526529] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.541132] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.547681] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.569023] io scheduler noop registered
[    0.573452] io scheduler deadline registered (default)
[    0.579647] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.589694] console [ttyS0] disabled
[    0.613789] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.623427] console [ttyS0] enabled
[    0.623427] console [ttyS0] enabled
[    0.630842] bootconsole [early0] disabled
[    0.630842] bootconsole [early0] disabled
[    0.646124] m25p80 spi0.0: found w25q128, expected m25p80
[    0.660796] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.665950] 5 tp-link partitions found on MTD device spi0.0
[    0.671605] Creating 5 MTD partitions on "spi0.0":
[    0.676506] 0x000000000000-0x000000020000 : "u-boot"
[    0.683687] 0x000000020000-0x000000172750 : "kernel"
[    0.690919] 0x000000172750-0x000000ff0000 : "rootfs"
[    0.697769] mtd: device 2 (rootfs) set to be root filesystem
[    0.703612] 1 squashfs-split partitions found on MTD device rootfs
[    0.709896] 0x000000730000-0x000000ff0000 : "rootfs_data"
[    0.717760] 0x000000ff0000-0x000001000000 : "art"
[    0.724825] 0x000000020000-0x000000ff0000 : "firmware"
[    0.733426] libphy: Fixed MDIO Bus: probed
[    0.748867] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.415795] libphy: ag71xx_mdio: probed
[    2.044064] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    2.055635] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.064121] NET: Registered protocol family 10
[    2.073139] NET: Registered protocol family 17
[    2.077714] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.091009] 8021q: 802.1Q VLAN Support v1.8
[    2.097277] hctosys: unable to open rtc device (rtc0)
[    2.106174] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.115025] Freeing unused kernel memory: 308K
[    2.119538] This architecture does not have kernel memory protection.
[    2.562680] random: fast init done
[    2.791140] init: Console is alive
[    2.794891] init: - watchdog -
[    5.115406] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.399771] usbcore: registered new interface driver usbfs
[    5.405503] usbcore: registered new interface driver hub
[    5.411001] usbcore: registered new device driver usb
[    5.454954] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.471509] SCSI subsystem initialized
[    5.481266] ehci-platform: EHCI generic platform driver
[    5.486736] ehci-platform ehci-platform: EHCI Host Controller
[    5.492601] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.502777] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.532755] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.540158] hub 1-0:1.0: USB hub found
[    5.544384] hub 1-0:1.0: 1 port detected
[    5.553936] usbcore: registered new interface driver usb-storage
[    5.569347] usbcore: registered new interface driver uas
[    5.575629] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.585455] init: - preinit -
[    6.104022] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.313304] hub 1-1:1.0: USB hub found
[    6.321438] hub 1-1:1.0: 4 ports detected
[    6.466345] random: procd: uninitialized urandom read (4 bytes read)
[    6.763988] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press [    6.842740] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.616553] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[    7.623916] scsi host0: usb-storage 1-1.1:1.0
[    7.722678] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[    7.793918] eth0: link up (1000Mbps/Full duplex)
[    7.798690] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.889590] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    7.896883] scsi host1: usb-storage 1-1.2:1.0
[    8.002677] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[    8.272677] usb 1-1.4: new high-speed USB device number 6 using ehci-platform
[    8.427417] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    8.434604] scsi host2: usb-storage 1-1.4:1.0
[    8.439906] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[    8.447575] scsi host3: usb-storage 1-1.4:1.1
[    8.673910] scsi 0:0:0:0: Direct-Access     ADATA    USB Flash Drive  1100 PQ: 0 ANSI: 0 CCS
[    8.685403] sd 0:0:0:0: [sda] 7925760 512-byte logical blocks: (4.06 GB/3.78 GiB)
[    8.693816] sd 0:0:0:0: [sda] Write Protect is off
[    8.699427] sd 0:0:0:0: [sda] No Caching mode page found
[    8.704892] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.716724]  sda: sda1 sda2
[    8.723811] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    9.033040] mount_root: loading kmods from internal overlay
[    9.125332] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    9.141376] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    9.597586] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[    9.607342] scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[    9.619989] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   10.139935] jffs2: notice: (520) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orph.
[   10.156176] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
/dev/sda1: recovering journal
[   11.510179] scsi 1:0:0:0: Direct-Access     Wilk     USB DISK 2.0     PMAP PQ: 0 ANSI: 6
[   11.523743] sd 1:0:0:0: [sdc] 30322688 512-byte logical blocks: (15.5 GB/14.5 GiB)
[   11.533699] sd 1:0:0:0: [sdc] Write Protect is off
[   11.540181] sd 1:0:0:0: [sdc] No Caching mode page found
[   11.545643] sd 1:0:0:0: [sdc] Assuming drive cache: write through
[   11.564483]  sdc: sdc1
[   11.575067] sd 1:0:0:0: [sdc] Attached SCSI removable disk
/dev/sda1: clean, 2999/185840 files, 44200/742784 blocks
[   11.890225] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: 
[   11.998466] mount_root: switched to extroot
[   12.007343] urandom-seed: Seeding with /etc/urandom.seed
[   12.184697] eth0: link down
[   12.201631] procd: - early -
[   12.204803] procd: - watchdog -
[   12.868677] procd: - watchdog -
[   12.872132] procd: - ubus -
[   13.261809] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.280431] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.291018] random: jshn: uninitialized urandom read (4 bytes read)
[   13.299009] procd: - init -
Please press Enter to activate this console.
[   14.727900] usb 1-1.4: USB disconnect, device number 6
[   14.912962] kmodloader: loading kernel modules from /etc/modules.d/*
[   15.087441] Key type dns_resolver registered
[   15.122499] RPC: Registered named UNIX socket transport module.
[   15.128568] RPC: Registered udp transport module.
[   15.133350] RPC: Registered tcp transport module.
[   15.138118] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   15.163096] tun: Universal TUN/TAP device driver, 1.6
[   15.168233] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   15.191567] gre: GRE over IPv4 demultiplexor driver
[   15.199318] ip_gre: GRE over IPv4 tunneling driver
[   15.245571] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   15.273548] i2c /dev entries driver
[   15.292888] Linux video capture interface: v2.00
[   15.330769] u32 classifier
[   15.333584]     input device check on
[   15.337296]     Actions configured
[   15.344499] Mirror/redirect action on
[   15.425623] fuse init (API version 7.26)
[   15.541093] usbcore: registered new interface driver cdc_acm
[   15.546923] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   15.577724] usbcore: registered new interface driver cdc_wdm
[   15.596870] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   15.605069] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   15.625752] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[   15.632312] usbcore: registered new interface driver cpia2
[   15.678784] Ebtables v2.0 registered
[   15.716032] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.754138] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   16.397780] usbcore: registered new interface driver ums-alauda
[   16.415565] usbcore: registered new interface driver ums-cypress
[   16.436188] usbcore: registered new interface driver ums-datafab
[   16.446065] usbcore: registered new interface driver ums-freecom
[   16.463862] usbcore: registered new interface driver ums-isd200
[   16.484551] usbcore: registered new interface driver ums-jumpshot
[   16.531675] usbcore: registered new interface driver ums-karma
[   16.573754] usbcore: registered new interface driver ums-sddr09
[   16.628729] usbcore: registered new interface driver ums-sddr55
[   16.678849] usbcore: registered new interface driver ums-usbat
[   16.742475] usbcore: registered new interface driver usblp
[   16.854522] usbcore: registered new interface driver usbserial
[   16.860547] usbcore: registered new interface driver usbserial_generic
[   16.867344] usbserial: USB Serial support registered for generic
[   17.073995] xt_time: kernel timezone is -0000
[   17.083137] usbcore: registered new interface driver cdc_ether
[   17.109414] usbcore: registered new interface driver cdc_ncm
[   17.250174] gspca_main: v2.14.0 registered
[   17.285225] usbcore: registered new interface driver mars
[   17.294377] usbcore: registered new interface driver mr97310a
[   17.314219] usbcore: registered new interface driver ov519
[   17.345731] usbcore: registered new interface driver ov534
[   17.364505] usbcore: registered new interface driver ov534_9
[   17.373956] usbcore: registered new interface driver pac207
[   17.391738] usbcore: registered new interface driver pac7311
[   17.412181] usbcore: registered new interface driver se401
[   17.457031] usbcore: registered new interface driver gspca_sn9c20x
[   17.485834] usbcore: registered new interface driver sonixb
[   17.516629] usbcore: registered new interface driver sonixj
[   17.545665] usbcore: registered new interface driver spca500
[   17.557838] usbcore: registered new interface driver spca501
[   17.587740] usbcore: registered new interface driver spca506
[   17.609897] usbcore: registered new interface driver spca508
[   17.650921] usbcore: registered new interface driver spca561
[   17.672629] usbcore: registered new interface driver sq905
[   17.695287] usbcore: registered new interface driver sq905c
[   17.715872] usbcore: registered new interface driver stk014
[   17.727913] usbcore: registered new interface driver STV06xx
[   17.747510] usbcore: registered new interface driver sunplus
[   17.765855] usbcore: registered new interface driver t613
[   17.811307] usbcore: registered new interface driver tv8532
[   17.853214] usbcore: registered new interface driver vc032x
[   17.907928] usbcore: registered new interface driver gspca_zc3xx
[   17.969180] usbcore: registered new interface driver huawei_cdc_ncm
[   18.281365] PPP generic driver version 2.4.2
[   18.304972] NET: Registered protocol family 24
[   18.311927] PPTP driver version 0.8.5
[   18.336066] usbcore: registered new interface driver Philips webcam
[   18.367379] usbcore: registered new interface driver qmi_wwan
[   18.388316] usbcore: registered new interface driver rndis_host
[   18.417573] usbcore: registered new interface driver sierra
[   18.423419] usbserial: USB Serial support registered for Sierra USB modem
[   18.445885] usbcore: registered new interface driver sierra_net
[   18.498922] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:0766)
[   18.543753] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platform/usb1/1-1/1-1.3/1-1.3:1.0/input/input0
[   18.554670] usbcore: registered new interface driver uvcvideo
[   18.560499] USB Video Class driver (1.1.1)
[   18.716694] usbcore: registered new interface driver cdc_mbim
[   18.745831] usbcore: registered new interface driver conex
[   18.775747] usbcore: registered new interface driver etoms
[   18.805727] usbcore: registered new interface driver finepix
[   18.818653] usbcore: registered new interface driver gspca_gl860
[   18.850873] usbcore: registered new interface driver jeilinj
[   18.877387] usbcore: registered new interface driver konica
[   18.915147] usbcore: registered new interface driver ALi m5602
[   18.945760] usbcore: registered new interface driver option
[   18.951562] usbserial: USB Serial support registered for GSM modem (1-port)
[   18.988875] usbcore: registered new interface driver qcserial
[   18.994890] usbserial: USB Serial support registered for Qualcomm USB modem
[   19.064112] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[   19.071016] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   19.096583] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[   19.172733] usb 1-1.4: new high-speed USB device number 7 using ehci-platform
[   19.300661] kmodloader: done loading kernel modules from /etc/modules.d/*
[   19.348896] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[   19.376186] option 1-1.4:1.0: GSM modem (1-port) converter detected
[   19.382964] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB0
[   19.390602] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[   19.505361] cdc_ether 1-1.4:1.1 wwan0: register 'cdc_ether' at usb-ehci-platform-1.4, Mobile Broadband Network Device, 02:50:f3:00:00:00
[   19.518666] usb-storage 1-1.4:1.3: USB Mass Storage device detected
[   19.546294] option 1-1.4:1.3: GSM modem (1-port) converter detected
[   19.553092] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB1
[   19.560675] usb-storage 1-1.4:1.4: USB Mass Storage device detected
[   19.576666] option 1-1.4:1.4: GSM modem (1-port) converter detected
[   19.583438] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB2
[   19.590992] usb-storage 1-1.4:1.5: USB Mass Storage device detected
[   19.624658] scsi host2: usb-storage 1-1.4:1.5
[   19.629975] usb-storage 1-1.4:1.6: USB Mass Storage device detected
[   19.653304] scsi host3: usb-storage 1-1.4:1.6
[   20.679191] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[   20.689233] scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[   20.702936] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   25.372752] random: crng init done
[   25.376219] random: 6 urandom warning(s) missed due to ratelimiting
[   32.848600] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   36.258206] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   38.908195] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   40.648323] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   41.931882] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   41.947381] br-lan: port 1(eth0.1) entered blocking state
[   41.952970] br-lan: port 1(eth0.1) entered disabled state
[   41.958861] device eth0.1 entered promiscuous mode
[   41.963801] device eth0 entered promiscuous mode
[   41.972059] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   42.043717] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   42.807381] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   42.994227] eth0: link up (1000Mbps/Full duplex)
[   42.998987] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   43.085783] br-lan: port 1(eth0.1) entered blocking state
[   43.091276] br-lan: port 1(eth0.1) entered forwarding state
[   43.097163] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   43.223309] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   48.081108] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   48.109343] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   48.251802] br-lan: port 2(wlan1) entered blocking state
[   48.257262] br-lan: port 2(wlan1) entered disabled state
[   48.263104] device wlan1 entered promiscuous mode
[   48.268110] br-lan: port 2(wlan1) entered blocking state
[   48.273584] br-lan: port 2(wlan1) entered forwarding state
[   48.306549] br-lan: port 3(wlan0) entered blocking state
[   48.312050] br-lan: port 3(wlan0) entered disabled state
[   48.317940] device wlan0 entered promiscuous mode
[   48.583020] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   49.342904] br-lan: port 2(wlan1) entered disabled state
[   52.096998] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   52.103696] br-lan: port 3(wlan0) entered blocking state
[   52.109099] br-lan: port 3(wlan0) entered forwarding state
[   52.196720] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   52.203510] br-lan: port 2(wlan1) entered blocking state
[   52.208934] br-lan: port 2(wlan1) entered forwarding state
[   53.883749] 3g-wan: renamed from ppp0
[   56.090901] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   78.751230] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   81.709755] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   84.014011] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   99.750655] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[   99.757898]                old minutes west=0, new minutes west=-120
[  230.413257] br-lan: port 3(wlan0) entered disabled state
[  230.418894] br-lan: port 2(wlan1) entered disabled state
[  230.424372] br-lan: port 1(eth0.1) entered disabled state
[  230.520432] device eth0.1 left promiscuous mode
[  230.525355] device eth0 left promiscuous mode
[  230.530137] br-lan: port 1(eth0.1) entered disabled state
[  230.597463] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[  230.629389] device wlan0 left promiscuous mode
[  230.634230] br-lan: port 3(wlan0) entered disabled state
[  230.709655] device wlan1 left promiscuous mode
[  230.714825] br-lan: port 2(wlan1) entered disabled state
[  231.009153] eth0: link down
[  244.402525] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[  244.443580] br-lan: port 1(eth0.1) entered blocking state
[  244.449335] br-lan: port 1(eth0.1) entered disabled state
[  244.455427] device eth0.1 entered promiscuous mode
[  244.460596] device eth0 entered promiscuous mode
[  244.523862] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[  244.633215] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[  245.471254] eth0: link up (1000Mbps/Full duplex)
[  245.476228] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  245.565783] br-lan: port 1(eth0.1) entered blocking state
[  245.571366] br-lan: port 1(eth0.1) entered forwarding state
[  245.577514] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[  245.710350] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[  250.077697] 3g-wan: renamed from ppp0
[  253.442231] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[  253.489102] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  253.580123] br-lan: port 2(wlan1) entered blocking state
[  253.585979] br-lan: port 2(wlan1) entered disabled state
[  253.667454] device wlan1 entered promiscuous mode
[  253.673901] br-lan: port 3(wlan0) entered blocking state
[  253.679497] br-lan: port 3(wlan0) entered disabled state
[  253.730608] device wlan0 entered promiscuous mode
[  253.737652] br-lan: port 3(wlan0) entered blocking state
[  253.743182] br-lan: port 3(wlan0) entered forwarding state
[  254.510308] br-lan: port 3(wlan0) entered disabled state
[  255.743454] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  255.751315] br-lan: port 2(wlan1) entered blocking state
[  255.756793] br-lan: port 2(wlan1) entered forwarding state
[  255.859730] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  255.869628] br-lan: port 3(wlan0) entered blocking state
[  255.875161] br-lan: port 3(wlan0) entered forwarding state

a z tym sdc1 chyba też mu coś nie pasuje?

   53.883749] 3g-wan: renamed from ppp0
[   56.090901] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   78.751230] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   81.709755] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   84.014011] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   99.750655] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[   99.757898]                old minutes west=0, new minutes west=-120
[  230.413257] br-lan: port 3(wlan0) entered disabled state

2020-04-04 22:16:40

Cezary napisał/a:

Albo masz zepsutą bazę bandwidth. Odepnij extroota, uruchom bez niego i zobacz czy będzie działał.

odłączyłem extroot i narazie jest okej. (chociaż wiadomo nawet połączenia niema bez extroota)

a o co chodzi z tym sdc1 ? przecież niby u mnie, nie było sdc1, bo po dołączeniu drugiego pena (na fotki z motion) był pod sdb1
to

[   54.770761] 3g-wan: renamed from ppp0
[   56.633101] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   95.624769] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[   95.632022]                old minutes west=0, new minutes west=-120

albo tu

    33.294775] EXT4-fs (sdc1): recovery complete
[   33.299221] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   36.208298] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   39.258398] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   40.978397] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   42.718434] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)

i co mogę zrobić z tą bazą bandwidth? parę dni temu też zdażały sie resety potem ustały - można to naprawić bez konfiguracji na nowo?

2020-04-04 21:43:47

tu dalsza część logu

*          Build: 2018-02-23          *
***************************************

** Warning: bad env CRC, using default,
   use 'saveenv' to save it in FLASH

** Warning: reset caused by watchdog!

  BOARD: TP-Link TL-WDR3600 v1
    SOC: AR9344 rev. 2
    CPU: MIPS 74Kc
    RAM: 128 MB DDR2 32-bit CL3-4-4-10
  FLASH: 16 MB Winbond W25Q128
   PCIe: 168C:0033
    MAC: 64:70:02:D1:67:62
 CLOCKS: CPU/RAM/AHB/SPI/REF
         550/400/200/ 25/ 40 MHz

Hit any key to stop booting:  0

Booting image from 0x9F020000...

   Vendor/image name:    OpenWrt r7935-d08a63770c
   Hardware ID:          0x36000001
   Whole image size:     7.8 MB (8126464 bytes)
   Kernel size:          1.3 MB (1385806 bytes)
   Rootfs size:          5.7 MB (5958384 bytes)
   Kernel load address:  0x80060000
   Kernel entry point:   0x80060000

]

2020-04-04 21:42:19

Modem wpięty jest zawsze w to samo gniazdo (USB-mod ) zasilanie tego gniazda jest przez przetwornicę LM2596 taką
https://abc-rc.pl/product-pol-5375-Prze … o-FPV.html jest raczje wystarczająca (2A do 3 z radiatorem) A modem to też słabiutki Huawei E173 i pod te gnaizdo też kamerka USB

ostatni raz się uruchomił ale właśnie akurat modem nie złapał połączenia (dioda miga)

a później odłączyłem modem i podłączyłem znowu ( cięgle wpięty pod serial) router najpierw się uruchomił, modem też załapał połaczenie i za chwilę reset - dotkłem w tym czasie akurat tego LM2596s aby sprawdzić czy ciepły - ale to chyba przypadek. Układ letni tylko.

***************************************
*     U-Boot 1.1.4-7a540a78-clean     *
*          Build: 2018-02-23          *
***************************************

** Warning: bad env CRC, using default,
   use 'saveenv' to save it in FLASH

  BOARD: TP-Link TL-WDR3600 v1
    SOC: AR9344 rev. 2
    CPU: MIPS 74Kc
    RAM: 128 MB DDR2 32-bit CL3-4-4-10
  FLASH: 16 MB Winbond W25Q128                                                  
   PCIe: 168C:0033                                                              
    MAC: 64:70:02:D1:67:62                                                      
 CLOCKS: CPU/RAM/AHB/SPI/REF                                                    
         550/400/200/ 25/ 40 MHz                                                
                                                                                
Hit any key to stop booting:  0                                                 
                                                                                
Booting image from 0x9F020000...                                                
                                                                                
   Vendor/image name:    OpenWrt r7935-d08a63770c                               
   Hardware ID:          0x36000001                                             
   Whole image size:     7.8 MB (8126464 bytes)                                 
   Kernel size:          1.3 MB (1385806 bytes)                                 
   Rootfs size:          5.7 MB (5958384 bytes)                                 
   Kernel load address:  0x80060000                                             
   Kernel entry point:   0x80060000                                             
                                                                                
   Header CRC...  skipped                                                       
   Data CRC...    skipped                                                       
                                                                                
Stopping network... OK!                                                         
Uncompressing Kernel...                                                         
                                                                                
***************************************                                         
*     U-Boot 1.1.4-7a540a78-clean     *                                         
*          Build: 2018-02-23          *                                         
***************************************                                         
                                                                                
** Warning: bad env CRC, using default,                                         
   use 'saveenv' to save it in FLASH                                            
                                                                                
  BOARD: TP-Link TL-WDR3600 v1                                                  
    SOC: AR9344 rev. 2                                                          
    CPU: MIPS 74Kc                                                              
    RAM: 128 MB DDR2 32-bit CL3-4-4-10                                          
  FLASH: 16 MB Winbond W25Q128                                                  
   PCIe: 168C:0033                                                              
    MAC: 64:70:02:D1:67:62                                                      
 CLOCKS: CPU/RAM/AHB/SPI/REF                                                    
         550/400/200/ 25/ 40 MHz                                                
                                                                                
Hit any key to stop booting:  0                                                 
                                                                                
Booting image from 0x9F020000...                                                
                                                                                
   Vendor/image name:    OpenWrt r7935-d08a63770c                               
   Hardware ID:          0x36000001                                             
   Whole image size:     7.8 MB (8126464 bytes)                                 
   Kernel size:          1.3 MB (1385806 bytes)                                 
   Rootfs size:          5.7 MB (5958384 bytes)                                 
   Kernel load address:  0x80060000                                             
   Kernel entry point:   0x80060000                                             
                                                                                
   Header CRC...  skipped                                                       
   Data CRC...    skipped                                                       
                                                                                
Stopping network... OK!                                                         
Uncompressing Kernel... OK!                                                     
Starting kernel...                                                              
                                                                                
[    0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (Op9
[    0.000000] bootconsole [early0] enabled                                     
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)                           
[    0.000000] SoC: Atheros AR9344 rev 2                                        
[    0.000000] Determined physical RAM map:                                     
[    0.000000]  memory: 08000000 @ 00000000 (usable)                            
[    0.000000] Initrd not found or empty - disabling initrd                     
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.  
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32s
[    0.000000] Zone ranges:                                                     
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]           
[    0.000000] Movable zone start for each node                                 
[    0.000000] Early memory node ranges                                         
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]          
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pa2
[    0.000000] Kernel command line:  board=TL-WDR4300  console=ttyS0,115200 rood
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)              
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)   
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)     
[    0.000000] Writing ErrCtl register=00000000                                 
[    0.000000] Readback ErrCtl register=00000000                                
[    0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdat)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1       
[    0.000000] NR_IRQS:51                                                       
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.0z
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_s
[    0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809s
[    0.008722] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)          
[    0.081684] pid_max: default: 32768 minimum: 301                             
[    0.086950] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)      
[    0.094339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) 
[    0.105222] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
[    0.116230] futex hash table entries: 256 (order: -1, 3072 bytes)            
[    0.124386] NET: Registered protocol family 16                               
[    0.130977] MIPS: machine is TP-LINK TL-WDR3600/4300/4310                    
[    0.140737] registering PCI controller with io_map_base unset                
[    0.396059] PCI host bridge to bus 0000:00                                   
[    0.400690] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]   
[    0.408354] pci_bus 0000:00: root bus resource [io  0x0000]                  
[    0.414580] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]    
[    0.422144] pci_bus 0000:00: No busn resource found for root bus, will use []
[    0.431033] pci 0000:00:00.0: invalid calibration data                       
[    0.437215] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64b]
[    0.445422] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pre]
[    0.453482] pci 0000:00:00.0: using irq 40 for pin 1                         
[    0.462664] clocksource: Switched to clocksource MIPS                        
[    0.469499] NET: Registered protocol family 2                                
[    0.475403] TCP established hash table entries: 1024 (order: 0, 4096 bytes)  
[    0.483242] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)         
[    0.490341] TCP: Hash tables configured (established 1024 bind 1024)         
[    0.497527] UDP hash table entries: 256 (order: 0, 4096 bytes)               
[    0.504086] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)          
[    0.511340] NET: Registered protocol family 1                                
[    0.519425] Crashlog allocated RAM at address 0x3f00000                      
[    0.526528] workingset: timestamp_bits=30 max_order=15 bucket_order=0        
[    0.541129] squashfs: version 4.0 (2009/01/31) Phillip Lougher               
[    0.547681] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORI.
[    0.569076] io scheduler noop registered                                     
[    0.573506] io scheduler deadline registered (default)                       
[    0.579696] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled         
[    0.589731] console [ttyS0] disabled                                         
[    0.613833] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 25A
[    0.623471] console [ttyS0] enabled                                          
[    0.623471] console [ttyS0] enabled                                          
[    0.630886] bootconsole [early0] disabled                                    
[    0.630886] bootconsole [early0] disabled                                    
[    0.646161] m25p80 spi0.0: found w25q128, expected m25p80                    
[    0.660744] m25p80 spi0.0: w25q128 (16384 Kbytes)                            
[    0.665896] 5 tp-link partitions found on MTD device spi0.0                  
[    0.671551] Creating 5 MTD partitions on "spi0.0":                           
[    0.676454] 0x000000000000-0x000000020000 : "u-boot"                         
[    0.683638] 0x000000020000-0x000000172750 : "kernel"                         
[    0.690881] 0x000000172750-0x000000ff0000 : "rootfs"                         
[    0.697736] mtd: device 2 (rootfs) set to be root filesystem                 
[    0.703576] 1 squashfs-split partitions found on MTD device rootfs           
[    0.709861] 0x000000730000-0x000000ff0000 : "rootfs_data"                    
[    0.717728] 0x000000ff0000-0x000001000000 : "art"                            
[    0.724804] 0x000000020000-0x000000ff0000 : "firmware"                       
[    0.733401] libphy: Fixed MDIO Bus: probed                                   
[    0.748848] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.415780] libphy: ag71xx_mdio: probed                                      
[    2.044069] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd]
[    2.055634] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII            
[    2.064115] NET: Registered protocol family 10                               
[    2.073138] NET: Registered protocol family 17                               
[    2.077715] bridge: filtering via arp/ip/ip6tables is no longer available by.
[    2.091008] 8021q: 802.1Q VLAN Support v1.8                                  
[    2.097280] hctosys: unable to open rtc device (rtc0)                        
[    2.106173] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. 
[    2.115023] Freeing unused kernel memory: 308K                               
[    2.119538] This architecture does not have kernel memory protection.        
[    2.562687] random: fast init done                                           
[    2.791125] init: Console is alive                                           
[    2.794873] init: - watchdog -                                               
[    5.116028] kmodloader: loading kernel modules from /etc/modules-boot.d/*    









































[    5.400651] usbcore: registered new interface driver usbfs
[    5.406384] usbcore: registered new interface driver hub
[    5.411890] usbcore: registered new device driver usb
[    5.455740] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.472229] SCSI subsystem initialized
[    5.481980] ehci-platform: EHCI generic platform driver
[    5.487449] ehci-platform ehci-platform: EHCI Host Controller
[    5.493339] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.503493] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.532760] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.540111] hub 1-0:1.0: USB hub found
[    5.544380] hub 1-0:1.0: 1 port detected
[    5.553795] usbcore: registered new interface driver usb-storage
[    5.569229] usbcore: registered new interface driver uas
[    5.575506] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.585326] init: - preinit -
[    6.103770] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.306821] hub 1-1:1.0: USB hub found
[    6.321577] hub 1-1:1.0: 4 ports detected
[    6.510733] random: procd: uninitialized urandom read (4 bytes read)
[    6.764757] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press [    6.842778] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.606397] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[    7.613800] scsi host0: usb-storage 1-1.1:1.0
[    7.712685] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[    7.793924] eth0: link up (1000Mbps/Full duplex)
[    7.798702] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.879537] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    7.886843] scsi host1: usb-storage 1-1.2:1.0
[    7.992683] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[    8.262683] usb 1-1.4: new high-speed USB device number 6 using ehci-platform
[    8.417620] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    8.424834] scsi host2: usb-storage 1-1.4:1.0
[    8.430141] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[    8.437779] scsi host3: usb-storage 1-1.4:1.1
[    8.673873] scsi 0:0:0:0: Direct-Access     ADATA    USB Flash Drive  1100 PQ: 0 ANSI: 0 CCS
[    8.685185] sd 0:0:0:0: [sda] 7925760 512-byte logical blocks: (4.06 GB/3.78 GiB)
[    8.693662] sd 0:0:0:0: [sda] Write Protect is off
[    8.699266] sd 0:0:0:0: [sda] No Caching mode page found
[    8.704729] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.716557]  sda: sda1 sda2
[    8.723646] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    9.474651] scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[    9.485429] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[    9.498741] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   10.037290] mount_root: loading kmods from internal overlay
[   10.129495] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.145582] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   11.097710] jffs2: notice: (536) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orph.
[   11.113935] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   11.516162] scsi 1:0:0:0: Direct-Access     Wilk     USB DISK 2.0     PMAP PQ: 0 ANSI: 6
[   11.544233] sd 1:0:0:0: [sdc] 30322688 512-byte logical blocks: (15.5 GB/14.5 GiB)
[   11.586881] sd 1:0:0:0: [sdc] Write Protect is off
[   11.593431] sd 1:0:0:0: [sdc] No Caching mode page found
[   11.598837] sd 1:0:0:0: [sdc] Assuming drive cache: write through
[   11.688428]  sdc: sdc1
/dev/sda1: recov[   11.699058] sd 1:0:0:0: [sdc] Attached SCSI removable disk
ering journal
/dev/sda1: clean, 2932/185840 files, 43382/742784 blocks
[   12.803640] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: 
[   12.911438] mount_root: switched to extroot
[   12.920304] urandom-seed: Seeding with /etc/urandom.seed
[   13.096700] eth0: link down
[   13.113624] procd: - early -
[   13.116661] procd: - watchdog -
[   13.778548] procd: - watchdog -
[   13.781994] procd: - ubus -
[   14.178783] random: ubusd: uninitialized urandom read (4 bytes read)
[   14.197141] random: ubusd: uninitialized urandom read (4 bytes read)
[   14.207938] random: jshn: uninitialized urandom read (4 bytes read)
[   14.216033] procd: - init -
Please press Enter to activate this console.
[   15.753253] usb 1-1.4: USB disconnect, device number 6
[   15.835764] kmodloader: loading kernel modules from /etc/modules.d/*
[   16.017119] Key type dns_resolver registered
[   16.052729] RPC: Registered named UNIX socket transport module.
[   16.058739] RPC: Registered udp transport module.
[   16.063532] RPC: Registered tcp transport module.
[   16.068304] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   16.093577] tun: Universal TUN/TAP device driver, 1.6
[   16.098727] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   16.122031] gre: GRE over IPv4 demultiplexor driver
[   16.129761] ip_gre: GRE over IPv4 tunneling driver
[   16.175737] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   16.265183] i2c /dev entries driver
[   16.287652] Linux video capture interface: v2.00
[   16.406501] u32 classifier
[   16.409303]     input device check on
[   16.413053]     Actions configured
[   16.435881] Mirror/redirect action on
[   16.518485] fuse init (API version 7.26)
[   16.597282] usbcore: registered new interface driver cdc_acm
[   16.603097] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   16.635120] usbcore: registered new interface driver cdc_wdm
[   16.650243] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   16.658426] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   16.681493] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[   16.688066] usbcore: registered new interface driver cpia2
[   16.746005] Ebtables v2.0 registered
[   16.779043] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.830122] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   17.716145] usbcore: registered new interface driver ums-alauda
[   17.735597] usbcore: registered new interface driver ums-cypress
[   17.755988] usbcore: registered new interface driver ums-datafab
[   17.775592] usbcore: registered new interface driver ums-freecom
[   17.790699] usbcore: registered new interface driver ums-isd200
[   17.811275] usbcore: registered new interface driver ums-jumpshot
[   17.825480] usbcore: registered new interface driver ums-karma
[   17.847072] usbcore: registered new interface driver ums-sddr09
[   17.865936] usbcore: registered new interface driver ums-sddr55
[   17.886580] usbcore: registered new interface driver ums-usbat
[   17.907085] usbcore: registered new interface driver usblp
[   17.954121] usbcore: registered new interface driver usbserial
[   17.960195] usbcore: registered new interface driver usbserial_generic
[   17.966976] usbserial: USB Serial support registered for generic
[   18.151538] xt_time: kernel timezone is -0000
[   18.162984] usbcore: registered new interface driver cdc_ether
[   18.196614] usbcore: registered new interface driver cdc_ncm
[   18.410489] gspca_main: v2.14.0 registered
[   18.449163] usbcore: registered new interface driver mars
[   18.475618] usbcore: registered new interface driver mr97310a
[   18.496267] usbcore: registered new interface driver ov519
[   18.513687] usbcore: registered new interface driver ov534
[   18.533548] usbcore: registered new interface driver ov534_9
[   18.565626] usbcore: registered new interface driver pac207
[   18.591699] usbcore: registered new interface driver pac7311
[   18.639949] usbcore: registered new interface driver se401
[   18.690105] usbcore: registered new interface driver gspca_sn9c20x
[   18.753766] usbcore: registered new interface driver sonixb
[   18.807150] usbcore: registered new interface driver sonixj
[   18.865263] usbcore: registered new interface driver spca500
[   18.905366] usbcore: registered new interface driver spca501
[   18.938148] usbcore: registered new interface driver spca506
[   18.965241] usbcore: registered new interface driver spca508
[   18.995077] usbcore: registered new interface driver spca561
[   19.005844] usbcore: registered new interface driver sq905
[   19.019520] usbcore: registered new interface driver sq905c
[   19.035871] usbcore: registered new interface driver stk014
[   19.057451] usbcore: registered new interface driver STV06xx
[   19.075800] usbcore: registered new interface driver sunplus
[   19.096030] usbcore: registered new interface driver t613
[   19.112190] usbcore: registered new interface driver tv8532
[   19.136439] usbcore: registered new interface driver vc032x
[   19.157926] usbcore: registered new interface driver gspca_zc3xx
[   19.174893] usbcore: registered new interface driver huawei_cdc_ncm
[   19.351856] PPP generic driver version 2.4.2
[   19.375002] NET: Registered protocol family 24
[   19.384750] PPTP driver version 0.8.5
[   19.416180] usbcore: registered new interface driver Philips webcam
[   19.437346] usbcore: registered new interface driver qmi_wwan
[   19.461281] usbcore: registered new interface driver rndis_host
[   19.507642] usbcore: registered new interface driver sierra
[   19.513474] usbserial: USB Serial support registered for Sierra USB modem
[   19.566489] usbcore: registered new interface driver sierra_net
[   19.622139] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:0766)
[   19.693451] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platform/usb1/1-1/1-1.3/1-1.3:1.0/input/input0
[   19.704357] usbcore: registered new interface driver uvcvideo
[   19.710184] USB Video Class driver (1.1.1)
[   19.912760] usb 1-1.4: new high-speed USB device number 7 using ehci-platform
[   19.924124] usbcore: registered new interface driver cdc_mbim
[   19.956017] usbcore: registered new interface driver conex
[   19.985998] usbcore: registered new interface driver etoms
[   20.010841] usbcore: registered new interface driver finepix
[   20.047518] usbcore: registered new interface driver gspca_gl860
[   20.078530] usbcore: registered new interface driver jeilinj
[   20.097397] usbcore: registered new interface driver konica
[   20.109969] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[   20.135182] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[   20.147704] usbcore: registered new interface driver ALi m5602
[   20.164071] cdc_ether 1-1.4:1.1 wwan0: register 'cdc_ether' at usb-ehci-platform-1.4, Mobile Broadband Network Device, 02:50:f3:00:00:00
[   20.177364] usb-storage 1-1.4:1.3: USB Mass Storage device detected
[   20.187906] usbcore: registered new interface driver option
[   20.193757] usbserial: USB Serial support registered for GSM modem (1-port)
[   20.203834] option 1-1.4:1.3: GSM modem (1-port) converter detected
[   20.210535] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB0
[   20.218132] usb-storage 1-1.4:1.4: USB Mass Storage device detected
[   20.226913] option 1-1.4:1.4: GSM modem (1-port) converter detected
[   20.233679] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB1
[   20.241203] usb-storage 1-1.4:1.5: USB Mass Storage device detected
[   20.249968] scsi host2: usb-storage 1-1.4:1.5
[   20.255314] usb-storage 1-1.4:1.6: USB Mass Storage device detected
[   20.263719] scsi host3: usb-storage 1-1.4:1.6
[   20.269486] option 1-1.4:1.0: GSM modem (1-port) converter detected
[   20.276319] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB2
[   20.344591] usbcore: registered new interface driver qcserial
[   20.350537] usbserial: USB Serial support registered for Qualcomm USB modem
[   20.459559] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[   20.466520] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   20.491903] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[   20.573415] kmodloader: done loading kernel modules from /etc/modules.d/*
[   21.322952] scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[   21.332886] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[   21.346470] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   23.616989] random: crng init done
[   23.620459] random: 6 urandom warning(s) missed due to ratelimiting
[   33.294775] EXT4-fs (sdc1): recovery complete
[   33.299221] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   36.208298] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   39.258398] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   40.978397] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   42.718434] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   42.906862] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   42.919421] br-lan: port 1(eth0.1) entered blocking state
[   42.924982] br-lan: port 1(eth0.1) entered disabled state
[   42.930874] device eth0.1 entered promiscuous mode
[   42.935785] device eth0 entered promiscuous mode
[   42.974087] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   43.041874] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   43.954185] eth0: link up (1000Mbps/Full duplex)
[   43.958973] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   44.042811] br-lan: port 1(eth0.1) entered blocking state
[   44.048300] br-lan: port 1(eth0.1) entered forwarding state
[   44.054165] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   44.187271] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   47.590193] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   49.204507] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   49.229496] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   49.327913] br-lan: port 2(wlan1) entered blocking state
[   49.333380] br-lan: port 2(wlan1) entered disabled state
[   49.339336] device wlan1 entered promiscuous mode
[   49.430959] br-lan: port 3(wlan0) entered blocking state
[   49.436427] br-lan: port 3(wlan0) entered disabled state
[   49.442350] device wlan0 entered promiscuous mode
[   52.672738] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   52.679436] br-lan: port 2(wlan1) entered blocking state
[   52.684916] br-lan: port 2(wlan1) entered forwarding state
[   52.962864] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   52.969580] br-lan: port 3(wlan0) entered blocking state
[   52.975036] br-lan: port 3(wlan0) entered forwarding state
[   55.198542] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   79.181779] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   81.621987] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   84.503089] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 1759.113308] usb 1-1.4: USB disconnect, device number 7
[ 1759.119141] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 1759.127747] option 1-1.4:1.0: device disconnected
[ 1759.133117] cdc_ether 1-1.4:1.1 wwan0: unregister 'cdc_ether' usb-ehci-platform-1.4, Mobile Broadband Network Device
[ 1759.245669] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 1759.254380] option 1-1.4:1.3: device disconnected
[ 1759.259798] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 1759.268391] option 1-1.4:1.4: device disconnected
[ 1769.811086] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)


***************************************
*     U-Boot 1.1.4-7a540a78-clean     *
*          Build: 2018-02-23          *
***************************************

** Warning: bad env CRC, using default,
   use 'saveenv' to save it in FLASH

  BOARD: TP-Link TL-WDR3600 v1
    SOC: AR9344 rev. 2
    CPU: MIPS 74Kc
    RAM: 128 MB DDR2 32-bit CL3-4-4-10
  FLASH: 16 MB Winbond W25Q128
   PCIe: 168C:0033
    MAC: 64:70:02:D1:67:62
 CLOCKS: CPU/RAM/AHB/SPI/REF
         550/400/200/ 25/ 40 MHz

Hit any key to stop booting:  0

Booting image from 0x9F020000...

   Vendor/image name:    OpenWrt r7935-d08a63770c
   Hardware ID:          0x36000001
   Whole image size:     7.8 MB (8126464 bytes)
   Kernel size:          1.3 MB (1385806 bytes)
   Rootfs size:          5.7 MB (5958384 bytes)
   Kernel load address:  0x80060000
   Kernel entry point:   0x80060000

   Header CRC...  skipped
   Data CRC...    skipped

Stopping network... OK!
Uncompressing Kernel... OK!
Starting kernel...

[    0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7865-5880dd48d5) ) #0 Wed Dec 11 21:46:13 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=TL-WDR4300  console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata, 448K rodata, 308K init, 211K bss, 6132K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6950037990 ns
[    0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809031678ns
[    0.008721] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)
[    0.081683] pid_max: default: 32768 minimum: 301
[    0.086951] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094340] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.105231] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.116239] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.124391] NET: Registered protocol family 16
[    0.130978] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[    0.140745] registering PCI controller with io_map_base unset
[    0.396084] PCI host bridge to bus 0000:00
[    0.400718] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.408380] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.414606] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.422171] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.431059] pci 0000:00:00.0: invalid calibration data
[    0.437238] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[    0.445440] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[    0.453500] pci 0000:00:00.0: using irq 40 for pin 1
[    0.462686] clocksource: Switched to clocksource MIPS
[    0.469523] NET: Registered protocol family 2
[    0.475424] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.483259] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.490359] TCP: Hash tables configured (established 1024 bind 1024)
[    0.497545] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.504104] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.511357] NET: Registered protocol family 1
[    0.519439] Crashlog allocated RAM at address 0x3f00000
[    0.526546] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.541139] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.547690] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.569063] io scheduler noop registered
[    0.573487] io scheduler deadline registered (default)
[    0.579681] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.589714] console [ttyS0] disabled
[    0.613814] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.623451] console [ttyS0] enabled
[    0.623451] console [ttyS0] enabled
[    0.630866] bootconsole [early0] disabled
[    0.630866] bootconsole [early0] disabled
[    0.646116] m25p80 spi0.0: found w25q128, expected m25p80
[    0.660795] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.665948] 5 tp-link partitions found on MTD device spi0.0
[    0.671602] Creating 5 MTD partitions on "spi0.0":
[    0.676504] 0x000000000000-0x000000020000 : "u-boot"
[    0.683689] 0x000000020000-0x000000172750 : "kernel"
[    0.690929] 0x000000172750-0x000000ff0000 : "rootfs"
[    0.697778] mtd: device 2 (rootfs) set to be root filesystem
[    0.703619] 1 squashfs-split partitions found on MTD device rootfs
[    0.709903] 0x000000730000-0x000000ff0000 : "rootfs_data"
[    0.717776] 0x000000ff0000-0x000001000000 : "art"
[    0.724842] 0x000000020000-0x000000ff0000 : "firmware"
[    0.733441] libphy: Fixed MDIO Bus: probed
[    0.748873] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.415797] libphy: ag71xx_mdio: probed
[    2.044091] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    2.055662] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.064153] NET: Registered protocol family 10
[    2.073172] NET: Registered protocol family 17
[    2.077747] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.091041] 8021q: 802.1Q VLAN Support v1.8
[    2.097315] hctosys: unable to open rtc device (rtc0)
[    2.106205] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.115076] Freeing unused kernel memory: 308K
[    2.119589] This architecture does not have kernel memory protection.
[    2.562704] random: fast init done
[    2.791453] init: Console is alive
[    2.795205] init: - watchdog -
[    5.115340] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.399274] usbcore: registered new interface driver usbfs
[    5.405009] usbcore: registered new interface driver hub
[    5.410515] usbcore: registered new device driver usb
[    5.452413] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.469598] SCSI subsystem initialized
[    5.479336] ehci-platform: EHCI generic platform driver
[    5.484805] ehci-platform ehci-platform: EHCI Host Controller
[    5.490662] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.500808] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.532786] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.540176] hub 1-0:1.0: USB hub found
[    5.544398] hub 1-0:1.0: 1 port detected
[    5.553957] usbcore: registered new interface driver usb-storage
[    5.569373] usbcore: registered new interface driver uas
[    5.575654] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.585477] init: - preinit -
[    6.105564] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.306836] hub 1-1:1.0: USB hub found
[    6.384931] hub 1-1:1.0: 4 ports detected
[    6.466937] random: procd: uninitialized urandom read (4 bytes read)
[    6.766384] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter fails[    6.842776] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
afe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.576614] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[    7.584021] scsi host0: usb-storage 1-1.1:1.0
[    7.682706] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[    7.793955] eth0: link up (1000Mbps/Full duplex)
[    7.798728] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.849636] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    7.856982] scsi host1: usb-storage 1-1.2:1.0
[    7.962719] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[    8.593971] scsi 0:0:0:0: Direct-Access     ADATA    USB Flash Drive  1100 PQ: 0 ANSI: 0 CCS
[    8.605443] sd 0:0:0:0: [sda] 7925760 512-byte logical blocks: (4.06 GB/3.78 GiB)
[    8.613875] sd 0:0:0:0: [sda] Write Protect is off
[    8.619487] sd 0:0:0:0: [sda] No Caching mode page found
[    8.624951] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.636904]  sda: sda1 sda2
[    8.643997] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   10.038875] mount_root: loading kmods from internal overlay
[   10.131621] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.147735] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   11.125003] jffs2: notice: (507) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orph.
[   11.141188] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   11.540776] scsi 1:0:0:0: Direct-Access     Wilk     USB DISK 2.0     PMAP PQ: 0 ANSI: 6
[   11.568829] sd 1:0:0:0: [sdb] 30322688 512-byte logical blocks: (15.5 GB/14.5 GiB)
[   11.611464] sd 1:0:0:0: [sdb] Write Protect is off
[   11.618152] sd 1:0:0:0: [sdb] No Caching mode page found
[   11.623632] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[   11.710057]  sdb: sdb1
[   11.721056] sd 1:0:0:0: [sdb] Attached SCSI removable disk
/dev/sda1: recovering journal
/dev/sda1: clean, 3007/185840 files, 44208/742784 blocks
[   12.080043] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: 
[   12.187677] mount_root: switched to extroot
[   12.196533] urandom-seed: Seeding with /etc/urandom.seed
[   12.373330] eth0: link down
[   12.390164] procd: - early -
[   12.393321] procd: - watchdog -
[   13.048876] procd: - watchdog -
[   13.052323] procd: - ubus -
[   13.443708] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.462253] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.472796] random: jshn: uninitialized urandom read (4 bytes read)
[   13.481836] procd: - init -
Please press Enter to activate this console.
[   15.066994] kmodloader: loading kernel modules from /etc/modules.d/*
[   15.239311] Key type dns_resolver registered
[   15.275640] RPC: Registered named UNIX socket transport module.
[   15.281654] RPC: Registered udp transport module.
[   15.286477] RPC: Registered tcp transport module.
[   15.291245] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   15.316205] tun: Universal TUN/TAP device driver, 1.6
[   15.321341] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   15.344851] gre: GRE over IPv4 demultiplexor driver
[   15.352609] ip_gre: GRE over IPv4 tunneling driver
[   15.398575] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   15.426791] i2c /dev entries driver
[   15.446299] Linux video capture interface: v2.00
[   15.508479] u32 classifier
[   15.511235]     input device check on
[   15.515002]     Actions configured
[   15.560386] Mirror/redirect action on
[   15.682551] fuse init (API version 7.26)
[   15.768281] usbcore: registered new interface driver cdc_acm
[   15.774110] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   15.805149] usbcore: registered new interface driver cdc_wdm
[   15.818855] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   15.827043] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   15.856696] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[   15.863267] usbcore: registered new interface driver cpia2
[   15.916271] Ebtables v2.0 registered
[   15.940186] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.986862] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   16.746611] usbcore: registered new interface driver ums-alauda
[   16.805589] usbcore: registered new interface driver ums-cypress
[   16.877830] usbcore: registered new interface driver ums-datafab
[   16.905437] usbcore: registered new interface driver ums-freecom
[   16.934825] usbcore: registered new interface driver ums-isd200
[   16.975965] usbcore: registered new interface driver ums-jumpshot
[   16.995522] usbcore: registered new interface driver ums-karma
[   17.020991] usbcore: registered new interface driver ums-sddr09
[   17.045756] usbcore: registered new interface driver ums-sddr55
[   17.066370] usbcore: registered new interface driver ums-usbat
[   17.085798] usbcore: registered new interface driver usblp
[   17.132869] usbcore: registered new interface driver usbserial
[   17.138907] usbcore: registered new interface driver usbserial_generic
[   17.145692] usbserial: USB Serial support registered for generic
[   17.315834] xt_time: kernel timezone is -0000
[   17.337041] usbcore: registered new interface driver cdc_ether
[   17.359254] usbcore: registered new interface driver cdc_ncm
[   17.513822] gspca_main: v2.14.0 registered
[   17.545312] usbcore: registered new interface driver mars
[   17.575609] usbcore: registered new interface driver mr97310a
[   17.598260] usbcore: registered new interface driver ov519
[   17.622945] usbcore: registered new interface driver ov534
[   17.649970] usbcore: registered new interface driver ov534_9
[   17.685221] usbcore: registered new interface driver pac207
[   17.716519] usbcore: registered new interface driver pac7311
[   17.745845] usbcore: registered new interface driver se401
[   17.757109] usbcore: registered new interface driver gspca_sn9c20x
[   17.778520] usbcore: registered new interface driver sonixb
[   17.796674] usbcore: registered new interface driver sonixj
[   17.815690] usbcore: registered new interface driver spca500
[   17.863272] usbcore: registered new interface driver spca501
[   17.896937] usbcore: registered new interface driver spca506
[   17.947382] usbcore: registered new interface driver spca508
[   17.985825] usbcore: registered new interface driver spca561
[   18.042023] usbcore: registered new interface driver sq905
[   18.098114] usbcore: registered new interface driver sq905c
[   18.161780] usbcore: registered new interface driver stk014
[   18.196037] usbcore: registered new interface driver STV06xx
[   18.235585] usbcore: registered new interface driver sunplus
[   18.256071] usbcore: registered new interface driver t613
[   18.275211] usbcore: registered new interface driver tv8532
[   18.306461] usbcore: registered new interface driver vc032x
[   18.327975] usbcore: registered new interface driver gspca_zc3xx
[   18.344945] usbcore: registered new interface driver huawei_cdc_ncm
[   18.513257] PPP generic driver version 2.4.2
[   18.538854] NET: Registered protocol family 24
[   18.550597] PPTP driver version 0.8.5
[   18.574488] usbcore: registered new interface driver Philips webcam
[   18.616226] usbcore: registered new interface driver qmi_wwan
[   18.638105] usbcore: registered new interface driver rndis_host
[   18.667582] usbcore: registered new interface driver sierra
[   18.673424] usbserial: USB Serial support registered for Sierra USB modem
[   18.703157] usbcore: registered new interface driver sierra_net
[   18.744507] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:0766)
[   18.814924] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platform/usb1/1-1/1-1.3/1-1.3:1.0/input/input0
[   18.825829] usbcore: registered new interface driver uvcvideo
[   18.831660] USB Video Class driver (1.1.1)
[   19.036706] usbcore: registered new interface driver cdc_mbim
[   19.048271] usbcore: registered new interface driver conex
[   19.065676] usbcore: registered new interface driver etoms
[   19.085612] usbcore: registered new interface driver finepix
[   19.133500] usbcore: registered new interface driver gspca_gl860
[   19.174939] usbcore: registered new interface driver jeilinj
[   19.226728] usbcore: registered new interface driver konica
[   19.291331] usbcore: registered new interface driver ALi m5602
[   19.353913] usbcore: registered new interface driver option
[   19.359721] usbserial: USB Serial support registered for GSM modem (1-port)
[   19.463277] usbcore: registered new interface driver qcserial
[   19.469223] usbserial: USB Serial support registered for Qualcomm USB modem
[   19.571410] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[   19.578388] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   19.603960] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[   19.693432] kmodloader: done loading kernel modules from /etc/modules.d/*
[   26.298123] random: crng init done
[   26.301589] random: 6 urandom warning(s) missed due to ratelimiting
[   30.293113] EXT4-fs (sdb1): recovery complete
[   30.297557] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[   32.327919] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[   36.128244] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[   38.138259] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[   40.068255] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[   41.697227] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   41.724910] br-lan: port 1(eth0.1) entered blocking state
[   41.730405] br-lan: port 1(eth0.1) entered disabled state
[   41.736383] device eth0.1 entered promiscuous mode
[   41.741249] device eth0 entered promiscuous mode
[   41.774136] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   41.843972] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   42.754279] eth0: link up (1000Mbps/Full duplex)
[   42.759045] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   42.856427] br-lan: port 1(eth0.1) entered blocking state
[   42.861918] br-lan: port 1(eth0.1) entered forwarding state
[   42.867792] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   43.012794] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   47.824949] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   47.862654] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   47.916602] br-lan: port 2(wlan1) entered blocking state
[   47.922005] br-lan: port 2(wlan1) entered disabled state
[   47.927896] device wlan1 entered promiscuous mode
[   48.006643] br-lan: port 3(wlan0) entered blocking state
[   48.012045] br-lan: port 3(wlan0) entered disabled state
[   48.017915] device wlan0 entered promiscuous mode
[   48.022842] br-lan: port 3(wlan0) entered blocking state
[   48.028238] br-lan: port 3(wlan0) entered forwarding state
[   48.883831] br-lan: port 3(wlan0) entered disabled state
[   50.393764] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   50.400435] br-lan: port 2(wlan1) entered blocking state
[   50.405928] br-lan: port 2(wlan1) entered forwarding state
[   50.478989] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   50.485786] br-lan: port 3(wlan0) entered blocking state
[   50.491223] br-lan: port 3(wlan0) entered forwarding state
[   53.648424] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[  160.682748] usb 1-1.4: new high-speed USB device number 6 using ehci-platform
[  160.858132] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[  160.882791] scsi host2: usb-storage 1-1.4:1.0
[  160.888321] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[  160.923579] scsi host3: usb-storage 1-1.4:1.1
[  161.960050] scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[  161.971257] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[  161.989451] sd 3:0:0:0: [sdc] Attached SCSI removable disk
[  162.439237] usb 1-1.4: USB disconnect, device number 6
[  166.260662] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[  166.574338] usb 1-1.4: new high-speed USB device number 7 using ehci-platform
[  166.772080] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[  166.788908] option 1-1.4:1.0: GSM modem (1-port) converter detected
[  166.797271] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB0
[  166.805337] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[  166.858738] cdc_ether 1-1.4:1.1 wwan0: register 'cdc_ether' at usb-ehci-platform-1.4, Mobile Broadband Network Device, 02:50:f3:00:00:00
[  166.872517] usb-storage 1-1.4:1.3: USB Mass Storage device detected
[  166.916218] option 1-1.4:1.3: GSM modem (1-port) converter detected
[  166.925135] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB1
[  166.933820] usb-storage 1-1.4:1.4: USB Mass Storage device detected
[  167.025766] option 1-1.4:1.4: GSM modem (1-port) converter detected
[  167.032909] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB2
[  167.042085] usb-storage 1-1.4:1.5: USB Mass Storage device detected
[  167.158201] scsi host2: usb-storage 1-1.4:1.5
[  167.163823] usb-storage 1-1.4:1.6: USB Mass Storage device detected
[  167.189933] scsi host3: usb-storage 1-1.4:1.6
[  168.199255] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[  168.277382] scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[  168.294890] sd 3:0:0:0: [sdc] Attached SCSI removable disk
[  168.568566] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[  170.890780] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[  184.446821] 3g-wan: renamed from ppp0
[  188.625714] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[  191.299794] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[  195.129403] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[  202.468689] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[  202.476011]                old minutes west=0, new minutes west=-120
[  229.957556] CPU 0 Unable to handle kernel paging request at virtual address 7a561d40, epc == 8745bd00, ra == 8745bda4
[  229.968345] Oops[#1]:
[  229.970657] CPU: 0 PID: 5688 Comm: bw_set Not tainted 4.9.206 #0
[  229.976751] task: 8521ca70 task.stack: 852dc000
[  229.981339] $ 0   : 00000000 7fc7ca94 f3ff9d44 7a561d40
[  229.986680] $ 4   : 00000001 00000001 00000001 860eb280
[  229.992012] $ 8   : 000318c7 000318c6 860eb680 6d6f6e2f
[  229.997345] $12   : 00000000 0a886034 00000007 00000000
[  230.002678] $16   : 861a5e00 86568000 860eb600 f3ff9d40
[  230.008011] $20   : 5e87ce00 00000000 5e891f80 5e7ff388
[  230.013344] $24   : 00000002 80313760                  
[  230.018677] $28   : 852dc000 852dde20 5e88ecad 8745bda4
[  230.024010] Hi    : 00000000
[  230.026932] Lo    : 000047b4
[  230.029955] epc   : 8745bd00 0x8745bd00 [ipt_bandwidth@87458000+0x45a0]
[  230.036731] ra    : 8745bda4 0x8745bda4 [ipt_bandwidth@87458000+0x45a0]
[  230.043441] Status: 1100dc03 KERNEL EXL IE 
[  230.047720] Cause : 00800008 (ExcCode 02)
[  230.051783] BadVA : 7a561d40
[  230.054706] PrId  : 0001974c (MIPS 74Kc)
[  230.058681] Modules linked in: ath9k ath9k_common qcserial pppoe ppp_async option gspca_m5602 gspca_konica gspca_jeilinj gspca_gl860 gspca_finepix gspca_etoms gsph
[  230.323675] Process bw_set (pid: 5688, threadinfo=852dc000, task=8521ca70, tls=77dd3dc0)
[  230.331877] Stack : 8626d958 8626d7e8 77dc6000 00000054 00000002 00000000 5e7ff388 80430000
[  230.340412]         87460000 87460000 1fffffff 87460000 8521ca70 00000018 00000000 00000018
[  230.348948]         010170a0 00000000 62646973 74342d64 6f776e6c 6f61642d 6461792d 33310000
[  230.357484]         00000021 00000041 2f757372 2f646174 612f6277 6d6f6e2f 62000000 319e0c67
[  230.366020]         8745c330 00000800 87d28500 7fc78a94 00004000 77dc8000 77dc8000 00000000
[  230.374557]         ...
[  230.377047] Call Trace:[  230.379513] [<87460000>] 0x87460000 [hfsplus@87460000+0x13f00]
[  230.385562] [<87460000>] 0x87460000 [hfsplus@87460000+0x13f00]
[  230.391608] [<87460000>] 0x87460000 [hfsplus@87460000+0x13f00]
[  230.397665] [<802e4594>] 0x802e4594
[  230.401207] [<80293b78>] 0x80293b78
[  230.404837] [<80295510>] 0x80295510
[  230.408380] [<80102804>] 0x80102804
[  230.411919] [<8006f4cc>] 0x8006f4cc
[  230.415456] [<8006f680>] 0x8006f680
[  230.418991] [<80117ed8>] 0x80117ed8
[  230.422531] 
[  230.424039] Code: 00000000  02331821  26620004 <8c750000> 1080009c  02221021  8e040000  8c420000  afa20018 
[  230.433991] 
[  230.435552] ---[ end trace 86cecfa5ff278f19 ]---
[  230.443973] Kernel panic - not syncing: Fatal exception in interrupt
[  230.452618] Rebooting in 3 seconds..


***************************************

2020-04-04 20:32:11

Witam, mój WDR 3600 czasem łapie jakieś resety, jeszcze niedawno myślałem że to wina zasilania ponieważ brałem go na działkę gdzie czasami (przez solar) mam 14V ,
ale po powrocie do domu resety też są. Postanowiłem podłączyć się przez serial i oto co widać (poniżej)
Dwa razy się zresetował sam, pierwszym razem chyba sie w pełni uruchomił, drugim już nie zdążył a za trzecim razem już sam go wyłączyłem.

Sprzęt WDR3600 USB-Mod Gargoyle 1.12 + gsm ,kamerka ,extroot + dodatkowy pendraiw na zdjęcia z kamerki.

 

***************************************
*     U-Boot 1.1.4-7a540a78-clean     *
*          Build: 2018-02-23          *
***************************************

** Warning: bad env CRC, using default,
   use 'saveenv' to save it in FLASH

  BOARD: TP-Link TL-WDR3600 v1
    SOC: AR9344 rev. 2
    CPU: MIPS 74Kc
    RAM: 128 MB DDR2 32-bit CL3-4-4-10
  FLASH: 16 MB Winbond W25Q128
   PCIe: 168C:0033
    MAC: 64:70:02:D1:67:62
 CLOCKS: CPU/RAM/AHB/SPI/REF
         550/400/200/ 25/ 40 MHz

Hit any key to stop booting:  0

Booting image from 0x9F020000...

   Vendor/image name:    OpenWrt r7935-d08a63770c
   Hardware ID:          0x36000001
   Whole image size:     7.8 MB (8126464 bytes)
   Kernel size:          1.3 MB (1385806 bytes)
   Rootfs size:          5.7 MB (5958384 bytes)
   Kernel load address:  0x80060000
   Kernel entry point:   0x80060000

   Header CRC...  skipped
   Data CRC...    skipped

Stopping network... OK!
Uncompressing Kernel... OK!
Starting kernel...

[    0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7865-5880dd48d5) ) #0 Wed Dec 11 21:46:13 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=TL-WDR4300  console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata, 448K rodata, 308K init, 211K bss, 6132K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6950037990 ns
[    0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 7809031678ns
[    0.008721] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)
[    0.081683] pid_max: default: 32768 minimum: 301
[    0.086950] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.105229] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.116238] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.124386] NET: Registered protocol family 16
[    0.130976] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[    0.140736] registering PCI controller with io_map_base unset
[    0.396084] PCI host bridge to bus 0000:00
[    0.400716] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.408380] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.414607] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.422171] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.431060] pci 0000:00:00.0: invalid calibration data
[    0.437239] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[    0.445439] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[    0.453499] pci 0000:00:00.0: using irq 40 for pin 1
[    0.462680] clocksource: Switched to clocksource MIPS
[    0.469511] NET: Registered protocol family 2
[    0.475414] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.483251] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.490349] TCP: Hash tables configured (established 1024 bind 1024)
[    0.497536] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.504094] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.511349] NET: Registered protocol family 1
[    0.519432] Crashlog allocated RAM at address 0x3f00000
[    0.526536] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.541137] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.547690] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.569078] io scheduler noop registered
[    0.573505] io scheduler deadline registered (default)
[    0.579697] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.589736] console [ttyS0] disabled
[    0.613833] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.623470] console [ttyS0] enabled
[    0.623470] console [ttyS0] enabled
[    0.630885] bootconsole [early0] disabled
[    0.630885] bootconsole [early0] disabled
[    0.646141] m25p80 spi0.0: found w25q128, expected m25p80
[    0.660741] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.665895] 5 tp-link partitions found on MTD device spi0.0
[    0.671551] Creating 5 MTD partitions on "spi0.0":
[    0.676452] 0x000000000000-0x000000020000 : "u-boot"
[    0.683642] 0x000000020000-0x000000172750 : "kernel"
[    0.690872] 0x000000172750-0x000000ff0000 : "rootfs"
[    0.697722] mtd: device 2 (rootfs) set to be root filesystem
[    0.703557] 1 squashfs-split partitions found on MTD device rootfs
[    0.709833] 0x000000730000-0x000000ff0000 : "rootfs_data"
[    0.717696] 0x000000ff0000-0x000001000000 : "art"
[    0.724771] 0x000000020000-0x000000ff0000 : "firmware"
[    0.733373] libphy: Fixed MDIO Bus: probed
[    0.748880] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.415835] libphy: ag71xx_mdio: probed
[    2.044086] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    2.055653] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.064135] NET: Registered protocol family 10
[    2.073146] NET: Registered protocol family 17
[    2.077723] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    2.091014] 8021q: 802.1Q VLAN Support v1.8
[    2.097273] hctosys: unable to open rtc device (rtc0)
[    2.106163] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.115015] Freeing unused kernel memory: 308K
[    2.119527] This architecture does not have kernel memory protection.
[    2.562699] random: fast init done
[    2.791351] init: Console is alive
[    2.795103] init: - watchdog -
[    5.115975] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.400632] usbcore: registered new interface driver usbfs
[    5.406365] usbcore: registered new interface driver hub
[    5.411871] usbcore: registered new device driver usb
[    5.455918] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.472451] SCSI subsystem initialized
[    5.482220] ehci-platform: EHCI generic platform driver
[    5.487685] ehci-platform ehci-platform: EHCI Host Controller
[    5.493577] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.503729] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.532777] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.540101] hub 1-0:1.0: USB hub found
[    5.544375] hub 1-0:1.0: 1 port detected
[    5.553773] usbcore: registered new interface driver usb-storage
[    5.569232] usbcore: registered new interface driver uas
[    5.575514] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    5.585337] init: - preinit -
[    6.104103] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.306753] hub 1-1:1.0: USB hub found
[    6.384317] hub 1-1:1.0: 4 ports detected
[    6.466738] random: procd: uninitialized urandom read (4 bytes read)
[    6.764924] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press [    6.842768] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.566501] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[    7.573860] scsi host0: usb-storage 1-1.1:1.0
[    7.672702] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[    7.793959] eth0: link up (1000Mbps/Full duplex)
[    7.798739] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.839542] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    7.846831] scsi host1: usb-storage 1-1.2:1.0
[    7.952705] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[    8.222700] usb 1-1.4: new high-speed USB device number 6 using ehci-platform
[    8.377743] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    8.384905] scsi host2: usb-storage 1-1.4:1.0
[    8.390208] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[    8.397966] scsi host3: usb-storage 1-1.4:1.1
[    8.593985] scsi 0:0:0:0: Direct-Access     ADATA    USB Flash Drive  1100 PQ: 0 ANSI: 0 CCS
[    8.605269] sd 0:0:0:0: [sda] 7925760 512-byte logical blocks: (4.06 GB/3.78 GiB)
[    8.613769] sd 0:0:0:0: [sda] Write Protect is off
[    8.619376] sd 0:0:0:0: [sda] No Caching mode page found
[    8.624827] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.636669]  sda: sda1 sda2
[    8.643634] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    9.394242] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[    9.474241] scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[    9.503778] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   10.037430] mount_root: loading kmods from internal overlay
[   10.130170] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.146311] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   11.105735] jffs2: notice: (535) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   11.121918] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   11.522142] scsi 1:0:0:0: Direct-Access     Wilk     USB DISK 2.0     PMAP PQ: 0 ANSI: 6
[   11.550237] sd 1:0:0:0: [sdc] 30322688 512-byte logical blocks: (15.5 GB/14.5 GiB)
[   11.592942] sd 1:0:0:0: [sdc] Write Protect is off
[   11.599667] sd 1:0:0:0: [sdc] No Caching mode page found
[   11.605126] sd 1:0:0:0: [sdc] Assuming drive cache: write through
[   11.691435]  sdc: sdc1
[   11.702421] sd 1:0:0:0: [sdc] Attached SCSI removable disk
/dev/sda1: recovering journal
/dev/sda1: clean, 2932/185840 files, 43382/742784 blocks
[   12.844558] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[   12.951550] mount_root: switched to extroot
[   12.960420] urandom-seed: Seeding with /etc/urandom.seed
[   13.137832] eth0: link down
[   13.154876] procd: - early -
[   13.157905] procd: - watchdog -
[   13.819518] procd: - watchdog -
[   13.823060] procd: - ubus -
[   14.220196] random: ubusd: uninitialized urandom read (4 bytes read)
[   14.238521] random: ubusd: uninitialized urandom read (4 bytes read)
[   14.249333] random: jshn: uninitialized urandom read (4 bytes read)
[   14.257399] procd: - init -
Please press Enter to activate this console.
[   15.754024] usb 1-1.4: USB disconnect, device number 6
[   15.847617] kmodloader: loading kernel modules from /etc/modules.d/*
[   16.029069] Key type dns_resolver registered
[   16.063586] RPC: Registered named UNIX socket transport module.
[   16.069597] RPC: Registered udp transport module.
[   16.074426] RPC: Registered tcp transport module.
[   16.079201] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   16.104152] tun: Universal TUN/TAP device driver, 1.6
[   16.109285] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   16.132594] gre: GRE over IPv4 demultiplexor driver
[   16.140324] ip_gre: GRE over IPv4 tunneling driver
[   16.185865] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   16.213754] i2c /dev entries driver
[   16.233467] Linux video capture interface: v2.00
[   16.271202] u32 classifier
[   16.274022]     input device check on
[   16.277733]     Actions configured
[   16.284920] Mirror/redirect action on
[   16.340701] fuse init (API version 7.26)
[   16.442992] usbcore: registered new interface driver cdc_acm
[   16.448746] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   16.511548] usbcore: registered new interface driver cdc_wdm
[   16.527520] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   16.535723] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   16.566905] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[   16.573526] usbcore: registered new interface driver cpia2
[   16.619846] Ebtables v2.0 registered
[   16.655954] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.694673] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   17.339104] usbcore: registered new interface driver ums-alauda
[   17.365816] usbcore: registered new interface driver ums-cypress
[   17.375848] usbcore: registered new interface driver ums-datafab
[   17.385805] usbcore: registered new interface driver ums-freecom
[   17.403645] usbcore: registered new interface driver ums-isd200
[   17.424375] usbcore: registered new interface driver ums-jumpshot
[   17.473402] usbcore: registered new interface driver ums-karma
[   17.512256] usbcore: registered new interface driver ums-sddr09
[   17.565861] usbcore: registered new interface driver ums-sddr55
[   17.629099] usbcore: registered new interface driver ums-usbat
[   17.678890] usbcore: registered new interface driver usblp
[   17.801967] usbcore: registered new interface driver usbserial
[   17.808069] usbcore: registered new interface driver usbserial_generic
[   17.814848] usbserial: USB Serial support registered for generic
[   18.003143] xt_time: kernel timezone is -0000
[   18.026859] usbcore: registered new interface driver cdc_ether
[   18.059372] usbcore: registered new interface driver cdc_ncm
[   18.179554] gspca_main: v2.14.0 registered
[   18.205263] usbcore: registered new interface driver mars
[   18.225606] usbcore: registered new interface driver mr97310a
[   18.244481] usbcore: registered new interface driver ov519
[   18.263908] usbcore: registered new interface driver ov534
[   18.285835] usbcore: registered new interface driver ov534_9
[   18.305820] usbcore: registered new interface driver pac207
[   18.319829] usbcore: registered new interface driver pac7311
[   18.335899] usbcore: registered new interface driver se401
[   18.357058] usbcore: registered new interface driver gspca_sn9c20x
[   18.408671] usbcore: registered new interface driver sonixb
[   18.438579] usbcore: registered new interface driver sonixj
[   18.465689] usbcore: registered new interface driver spca500
[   18.495400] usbcore: registered new interface driver spca501
[   18.513300] usbcore: registered new interface driver spca506
[   18.539767] usbcore: registered new interface driver spca508
[   18.575842] usbcore: registered new interface driver spca561
[   18.609043] usbcore: registered new interface driver sq905
[   18.624851] usbcore: registered new interface driver sq905c
[   18.645885] usbcore: registered new interface driver stk014
[   18.667486] usbcore: registered new interface driver STV06xx
[   18.685997] usbcore: registered new interface driver sunplus
[   18.704783] usbcore: registered new interface driver t613
[   18.721947] usbcore: registered new interface driver tv8532
[   18.766438] usbcore: registered new interface driver vc032x
[   18.827937] usbcore: registered new interface driver gspca_zc3xx
[   18.894942] usbcore: registered new interface driver huawei_cdc_ncm
[   19.221338] PPP generic driver version 2.4.2
[   19.243745] NET: Registered protocol family 24
[   19.250700] PPTP driver version 0.8.5
[   19.278901] usbcore: registered new interface driver Philips webcam
[   19.307431] usbcore: registered new interface driver qmi_wwan
[   19.328354] usbcore: registered new interface driver rndis_host
[   19.357665] usbcore: registered new interface driver sierra
[   19.363500] usbserial: USB Serial support registered for Sierra USB modem
[   19.383454] usbcore: registered new interface driver sierra_net
[   19.436890] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:0766)
[   19.483829] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platform/usb1/1-1/1-1.3/1-1.3:1.0/input/input0
[   19.494735] usbcore: registered new interface driver uvcvideo
[   19.500566] USB Video Class driver (1.1.1)
[   19.656702] usbcore: registered new interface driver cdc_mbim
[   19.685860] usbcore: registered new interface driver conex
[   19.715767] usbcore: registered new interface driver etoms
[   19.745898] usbcore: registered new interface driver finepix
[   19.771932] usbcore: registered new interface driver gspca_gl860
[   19.796749] usbcore: registered new interface driver jeilinj
[   19.837349] usbcore: registered new interface driver konica
[   19.870110] usbcore: registered new interface driver ALi m5602
[   19.892798] usb 1-1.4: new high-speed USB device number 7 using ehci-platform
[   19.903443] usbcore: registered new interface driver option
[   19.909265] usbserial: USB Serial support registered for GSM modem (1-port)
[   19.944823] usbcore: registered new interface driver qcserial
[   19.950797] usbserial: USB Serial support registered for Qualcomm USB modem
[   20.061888] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[   20.068862] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   20.094362] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[   20.110466] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[   20.163509] option 1-1.4:1.0: GSM modem (1-port) converter detected
[   20.170213] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB0
[   20.177909] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[   20.226361] cdc_ether 1-1.4:1.1 wwan0: register 'cdc_ether' at usb-ehci-platform-1.4, Mobile Broadband Network Device, 02:50:f3:00:00:00
[   20.239680] usb-storage 1-1.4:1.3: USB Mass Storage device detected
[   20.293535] option 1-1.4:1.3: GSM modem (1-port) converter detected
[   20.300236] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB1
[   20.307827] usb-storage 1-1.4:1.4: USB Mass Storage device detected
[   20.343460] kmodloader: done loading kernel modules from /etc/modules.d/*
[   20.363357] option 1-1.4:1.4: GSM modem (1-port) converter detected
[   20.370049] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB2
[   20.377643] usb-storage 1-1.4:1.5: USB Mass Storage device detected
[   20.520741] scsi host2: usb-storage 1-1.4:1.5
[   20.526075] usb-storage 1-1.4:1.6: USB Mass Storage device detected
[   20.578877] scsi host3: usb-storage 1-1.4:1.6
[   21.583621] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
[   21.640117] scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[   21.654533] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   24.962775] random: crng init done
[   24.966242] random: 6 urandom warning(s) missed due to ratelimiting
[   33.414634] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   36.298287] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   39.348394] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   41.078285] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   42.736627] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   42.748729] br-lan: port 1(eth0.1) entered blocking state
[   42.754282] br-lan: port 1(eth0.1) entered disabled state
[   42.760193] device eth0.1 entered promiscuous mode
[   42.765109] device eth0 entered promiscuous mode
[   42.772146] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   42.821037] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   43.773161] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   43.794230] eth0: link up (1000Mbps/Full duplex)
[   43.798992] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   43.906898] br-lan: port 1(eth0.1) entered blocking state
[   43.912391] br-lan: port 1(eth0.1) entered forwarding state
[   43.918277] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   44.076749] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   48.874709] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   48.921815] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   48.976508] br-lan: port 2(wlan1) entered blocking state
[   48.981941] br-lan: port 2(wlan1) entered disabled state
[   48.987822] device wlan1 entered promiscuous mode
[   49.137650] br-lan: port 3(wlan0) entered blocking state
[   49.143116] br-lan: port 3(wlan0) entered disabled state
[   49.148960] device wlan0 entered promiscuous mode
[   49.153899] br-lan: port 3(wlan0) entered blocking state
[   49.159315] br-lan: port 3(wlan0) entered forwarding state
[   49.643134] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   50.192821] br-lan: port 3(wlan0) entered disabled state
[   52.792443] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   52.799254] br-lan: port 2(wlan1) entered blocking state
[   52.804732] br-lan: port 2(wlan1) entered forwarding state
[   52.967739] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   52.974473] br-lan: port 3(wlan0) entered blocking state
[   52.979877] br-lan: port 3(wlan0) entered forwarding state
[   54.732467] 3g-wan: renamed from ppp0
[   56.923784] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   79.367615] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[   81.891546] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   84.151602] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[  100.211672] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[  100.218952]                old minutes west=0, new minutes west=-120
[  127.752069] CPU 0 Unable to handle kernel paging request at virtual address 7
[  127.762855] Oops[#1]:
[  127.765166] CPU: 0 PID: 5426 Comm: bw_set Not tainted 4.9.206 #0
[  127.771260] task: 85a8df50 task.stack: 85a26000
[  127.775849] $ 0   : 00000000 7fedee14 f3ff9d44 7aba5d40
[  127.781190] $ 4   : 00000001 00000001 00000001 865be180
[  127.786523] $ 8   : 0002f72d 0002f72c 865bec80 6d6f6e2f
[  127.791855] $12   : 00000000 0a886034 00000007 00000000
[  127.797188] $16   : 863a8100 86bac000 865beb80 f3ff9d40
[  127.802521] $20   : 5e87ce00 00000000 5e891f80 5e7ff388
[  127.807854] $24   : 00000002 80313760
[  127.813187] $28   : 85a26000 85a27e20 5e88eb00 87733da4
[  127.818520] Hi    : 00000000
[  127.821442] Lo    : 000047b4
[  127.824465] epc   : 87733d00 0x87733d00 [ipt_bandwidth@87730000+0x45a0]
[  127.831242] ra    : 87733da4 0x87733da4 [ipt_bandwidth@87730000+0x45a0]
[  127.837950] Status: 1100dc03 KERNEL EXL IE
[  127.842220] Cause : 00800008 (ExcCode 02)
[  127.846285] BadVA : 7aba5d40
[  127.849207] PrId  : 0001974c (MIPS 74Kc)
[  127.853182] Modules linked in: ath9k ath9k_common qcserial pppoe ppp_async opet sierra rndis_host qmi_wwan pwc pptp pppox ppp_generic nf_nat_pptp nf_conntracsunplus gspca_stv06xx gspca_stk014 gspca_sq905c gspca_sq905 gspca_spca561 gspca_ gspca_ov534 gspca_ov519 gspca_mr97310a gspca_mars gspca_main ebtable_nat ebtablta xt_pkttype xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_xt_NETMAP xt_LOG xt_HL xt_DSCP xt_CT xt_CLASSIFY videobuf2_v4l2 usbserial usbneteject_ipv4 nf_nat_tftp nf_nat_snmp_basic nf_nat_sip nf_nat_redirect nf_nat_protodefrag_ipv6 nf_defrag_ipv4 nf_conntrack_tftp nf_conntrack_snmp nf_conntrack_sip[f_conntrack_amanda nf_conntrack iptable_mangle iptable_filter ipt_ECN ip_tables  cdc_acm fuse sch_multiq em_nbyte sch_dsmark sch_pie sch_gred sch_teql em_cmp clw cls_route cls_fw sch_tbf sch_htb sch_hfsc sch_ingress videobuf2_vmalloc videobos[  128.070146]  ip_gre gre ip_tunnel rpcsec_gss_krb5 auth_rpcgss oid_registry ls_cp852 nls_cp850 nls_cp775 nls_cp437 nls_cp1251 nls_cp1250 dma_shared_buffer sore nls_base usb_common crc16 exportfs mii aead crypto_null cryptomgr crc32c_gen
[  128.118175] Process bw_set (pid: 5426, threadinfo=85a26000, task=85a8df50, tl
[  128.126377] Stack : 861ff7a0 861ff0b0 77a98000 00000054 00000002 00000000 5e7
[  128.134913]         87730000 87730000 1fffffff 87730000 85a8df50 00000018 000
[  128.143449]         01019c80 00000000 62646973 74342d64 6f776e6c 6f61642d 646
[  128.151985]         00000021 00000041 2f757372 2f646174 612f6277 6d6f6e2f 620
[  128.160521]         87734330 00000800 87d28500 7fedae14 00004000 77a9a000 77a
[  128.169058]         ...
[  128.171548] Call Trace:[  128.174003] [<87730000>] 0x87730000 [ipt_bandwidth@
[  128.180478] [<87730000>] 0x87730000 [ipt_bandwidth@87730000+0x45a0]
[  128.186955] [<87730000>] 0x87730000 [ipt_bandwidth@87730000+0x45a0]
[  128.193460] [<802e4594>] 0x802e4594
[  128.197001] [<80293b78>] 0x80293b78
[  128.200625] [<80295510>] 0x80295510
[  128.204165] [<80102804>] 0x80102804
[  128.207704] [<8006f4cc>] 0x8006f4cc
[  128.211242] [<8006f680>] 0x8006f680
[  128.214777] [<80117ed8>] 0x80117ed8
[  128.218317]
[  128.219825] Code: 00000000  02331821  26620004 <8c750000> 1080009c  02221021
[  128.229778]
[  128.231347] ---[ end trace aa7954265135c613 ]---
[  128.239723] Kernel panic - not syncing: Fatal exception in interrupt
[  128.248292] Rebooting in 3 seconds..


***************************************
*     U-Boot 1.1.4-7a540a78-clean     *
*          Build: 2018-02-23          *
***************************************

** Warning: bad env CRC, using default,
   use 'saveenv' to save it in FLASH

** Warning: reset caused by watchdog!

  BOARD: TP-Link TL-WDR3600 v1
    SOC: AR9344 rev. 2
    CPU: MIPS 74Kc
    RAM: 128 MB DDR2 32-bit CL3-4-4-10
  FLASH: 16 MB Winbond W25Q128
   PCIe: 168C:0033
    MAC: 64:70:02:D1:67:62
 CLOCKS: CPU/RAM/AHB/SPI/REF
         550/400/200/ 25/ 40 MHz

Hit any key to stop booting:  0

Booting image from 0x9F020000...

   Vendor/image name:    OpenWrt r7935-d08a63770c
   Hardware ID:          0x36000001
   Whole image size:     7.8 MB (8126464 bytes)
   Kernel size:          1.3 MB (1385806 bytes)
   Rootfs size:          5.7 MB (5958384 bytes)
   Kernel load address:  0x80060000
   Kernel entry point:   0x80060000

   Header CRC...  skipped
   Data CRC...    skipped

Stopping network... OK!
Uncompressing Kernel... OK!
Starting kernel...

[    0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (Ope
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
[    0.000000] Kernel command line:  board=TL-WDR4300  console=ttyS0,115200 root
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.00
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i
[    0.000011] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 78090
[    0.008721] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)
[    0.081683] pid_max: default: 32768 minimum: 301
[    0.086950] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.105222] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma
[    0.116230] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.124382] NET: Registered protocol family 16
[    0.130969] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[    0.140736] registering PCI controller with io_map_base unset
[    0.396064] PCI host bridge to bus 0000:00
[    0.400699] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.408362] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.414588] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.422153] pci_bus 0000:00: No busn resource found for root bus, will use [b
[    0.431042] pci 0000:00:00.0: invalid calibration data
[    0.437223] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bi
[    0.445430] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref
[    0.453491] pci 0000:00:00.0: using irq 40 for pin 1
[    0.462670] clocksource: Switched to clocksource MIPS
[    0.469507] NET: Registered protocol family 2
[    0.475410] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.483250] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.490350] TCP: Hash tables configured (established 1024 bind 1024)
[    0.497535] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.504094] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.511348] NET: Registered protocol family 1
[    0.519426] Crashlog allocated RAM at address 0x3f00000
[    0.526822] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.541420] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.547973] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
[    0.569236] io scheduler noop registered
[    0.573664] io scheduler deadline registered (default)
[    0.579860] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.589903] console [ttyS0] disabled
[    0.613998] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 250
[    0.623630] console [ttyS0] enabled
[    0.623630] console [ttyS0] enabled
[    0.631045] bootconsole [early0] disabled
[    0.631045] bootconsole [early0] disabled
[    0.646356] m25p80 spi0.0: found w25q128, expected m25p80
[    0.660978] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.666125] 5 tp-link partitions found on MTD device spi0.0
[    0.671781] Creating 5 MTD partitions on "spi0.0":
[    0.676682] 0x000000000000-0x000000020000 : "u-boot"
[    0.683853] 0x000000020000-0x000000172750 : "kernel"
[    0.691087] 0x000000172750-0x000000ff0000 : "rootfs"
[    0.697974] mtd: device 2 (rootfs) set to be root filesystem
[    0.703814] 1 squashfs-split partitions found on MTD device rootfs
[    0.710090] 0x000000730000-0x000000ff0000 : "rootfs_data"
[    0.717923] 0x000000ff0000-0x000001000000 : "art"
[    0.725003] 0x000000020000-0x000000ff0000 : "firmware"
[    0.733588] libphy: Fixed MDIO Bus: probed
[    0.748779] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[    1.415951] libphy: ag71xx_mdio: probed
[    2.044076] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd0
[    2.055650] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.064142] NET: Registered protocol family 10
[    2.073163] NET: Registered protocol family 17
[    2.077731] bridge: filtering via arp/ip/ip6tables is no longer available by
[    2.091027] 8021q: 802.1Q VLAN Support v1.8
[    2.097325] hctosys: unable to open rtc device (rtc0)
[    2.106216] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.115065] Freeing unused kernel memory: 308K
[    2.119573] This architecture does not have kernel memory protection.
[    2.562686] random: fast init done
[    2.791197] init: Console is alive
[    2.794939] init: - watchdog -
[    5.115655] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.400775] usbcore: registered new interface driver usbfs
[    5.406507] usbcore: registered new interface driver hub
[    5.412012] usbcore: registered new device driver usb
[    5.456055] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.472612] SCSI subsystem initialized
[    5.482376] ehci-platform: EHCI generic platform driver
[    5.487846] ehci-platform ehci-platform: EHCI Host Controller
[    5.493736] ehci-platform ehci-platform: new USB bus registered, assigned bus
[    5.503890] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.532770] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.540099] hub 1-0:1.0: USB hub found
[    5.544374] hub 1-0:1.0: 1 port detected
[    5.553788] usbcore: registered new interface driver usb-storage
[    5.569222] usbcore: registered new interface driver uas
[    5.575500] kmodloader: done loading kernel modules from /etc/modules-boot.d/
[    5.585317] init: - preinit -
[    6.104945] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.306752] hub 1-1:1.0: USB hub found
[    6.384483] hub 1-1:1.0: 4 ports detected
[    6.466628] random: procd: uninitialized urandom read (4 bytes read)
[    6.763958] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3[    6.842770] usb 1-1.1: new high-speed USB device number
] or [4] key and hit [enter] to select the debug level
[    7.616412] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[    7.623773] scsi host0: usb-storage 1-1.1:1.0
[    7.722691] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[    7.793936] eth0: link up (1000Mbps/Full duplex)
[    7.798708] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.889573] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    7.896862] scsi host1: usb-storage 1-1.2:1.0
[    8.002691] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[    8.272691] usb 1-1.4: new full-speed USB device number 6 using ehci-platform
[    8.472693] usb 1-1.4: new high-speed USB device number 7 using ehci-platform
[    8.628373] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    8.636191] usb-storage 1-1.4:1.1: USB Mass Storage device detected
[    8.643931] usb-storage 1-1.4:1.2: USB Mass Storage device detected
[    8.651653] usb-storage 1-1.4:1.3: USB Mass Storage device detected
[    8.659429] usb-storage 1-1.4:1.4: USB Mass Storage device detected
[    8.667185] usb-storage 1-1.4:1.5: USB Mass Storage device detected
[    8.675172] scsi host2: usb-storage 1-1.4:1.5
[    8.680489] usb-storage 1-1.4:1.6: USB Mass Storage device detected
[    8.687898] scsi 0:0:0:0: Direct-Access     ADATA    USB Flash Drive  1100 PQ
[    8.699094] sd 0:0:0:0: [sda] 7925760 512-byte logical blocks: (4.06 GB/3.78
[    8.707664] sd 0:0:0:0: [sda] Write Protect is off
[    8.713332] sd 0:0:0:0: [sda] No Caching mode page found
[    8.718777] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.726150] scsi host3: usb-storage 1-1.4:1.6
[    8.736332]  sda: sda1 sda2
[    8.743554] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    9.720584] scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ
[    9.794279] scsi 3:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ
[    9.808688] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[   10.043940] mount_root: loading kmods from internal overlay
[   10.136778] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   10.152893] kmodloader: done loading kernel modules from //etc/modules-boot.d
[   11.117483] jffs2: notice: (551) jffs2_build_xattr_subsystem: complete buildi
[   11.133717] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   11.535596] scsi 1:0:0:0: Direct-Access     Wilk     USB DISK 2.0     PMAP PQ
[   11.564189] sd 1:0:0:0: [sdc] 30322688 512-byte logical blocks: (15.5 GB/14.5
[   11.606892] sd 1:0:0:0: [sdc] Write Protect is off
[   11.622768] sd 1:0:0:0: [sdc] No Caching mode page found
[   11.628203] sd 1:0:0:0: [sdc] Assuming drive cache: write through
[   11.708325]  sdc: sdc1
/dev/sda1: recov[   11.719081] sd 1:0:0:0: [sdc] Attached SCSI removable disk
ering journal
/dev/sda1: clean, 2932/185840 files, 43382/742784 blocks
[   12.878835] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[   12.987324] mount_root: switched to extroot
[   12.996212] urandom-seed: Seeding with /etc/urandom.seed
[   13.172862] eth0: link down
[   13.189824] procd: - early -
[   13.192992] procd: - watchdog -
[   13.852990] procd: - watchdog -
[   13.856434] procd: - ubus -
[   14.253640] random: ubusd: uninitialized urandom read (4 bytes read)
[   14.271917] random: ubusd: uninitialized urandom read (4 bytes read)
[   14.282629] random: jshn: uninitialized urandom read (4 bytes read)
[   14.290686] procd: - init -
Please press Enter to activate this console.
[   15.879327] kmodloader: loading kernel modules from /etc/modules.d/*
[   16.058673] Key type dns_resolver registered
[   16.094418] RPC: Registered named UNIX socket transport module.
[   16.100434] RPC: Registered udp transport module.
[   16.105257] RPC: Registered tcp transport module.
[   16.110025] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   16.135102] tun: Universal TUN/TAP device driver, 1.6
[   16.140237] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   16.163689] gre: GRE over IPv4 demultiplexor driver
[   16.171348] ip_gre: GRE over IPv4 tunneling driver
[   16.217007] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   16.245207] i2c /dev entries driver
[   16.264634] Linux video capture interface: v2.00
[   16.302437] u32 classifier
[   16.305250]     input device check on
[   16.308965]     Actions configured
[   16.316168] Mirror/redirect action on
[   16.366358] fuse init (API version 7.26)
[   16.469905] usbcore: registered new interface driver cdc_acm
[   16.475736] cdc_acm: USB Abstract Control Model driver for USB modems and ISD
[   16.547458] usbcore: registered new interface driver cdc_wdm
[   16.564735] Loading modules backported from Linux version wt-2017-11-01-0-gfe
[   16.572915] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   16.588948] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[   16.595556] usbcore: registered new interface driver cpia2
[   16.644903] Ebtables v2.0 registered
[   16.675971] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.714735] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   17.340123] usbcore: registered new interface driver ums-alauda
[   17.373836] usbcore: registered new interface driver ums-cypress
[   17.394488] usbcore: registered new interface driver ums-datafab
[   17.415438] usbcore: registered new interface driver ums-freecom
[   17.435868] usbcore: registered new interface driver ums-isd200
[   17.449376] usbcore: registered new interface driver ums-jumpshot
[   17.467063] usbcore: registered new interface driver ums-karma
[   17.488580] usbcore: registered new interface driver ums-sddr09
[   17.535780] usbcore: registered new interface driver ums-sddr55
[   17.596405] usbcore: registered new interface driver ums-usbat
[   17.636903] usbcore: registered new interface driver usblp
[   17.772832] usbcore: registered new interface driver usbserial
[   17.778863] usbcore: registered new interface driver usbserial_generic
[   17.785653] usbserial: USB Serial support registered for generic
[   18.053746] xt_time: kernel timezone is -0000
[   18.071555] cdc_ether 1-1.4:1.1 wwan0: register 'cdc_ether' at usb-ehci-platf
[   18.084258] usbcore: registered new interface driver cdc_ether
[   18.119424] usbcore: registered new interface driver cdc_ncm
[   18.244024] gspca_main: v2.14.0 registered
[   18.271181] usbcore: registered new interface driver mars
[   18.285550] usbcore: registered new interface driver mr97310a
[   18.314786] usbcore: registered new interface driver ov519
[   18.329717] usbcore: registered new interface driver ov534
[   18.355670] usbcore: registered new interface driver ov534_9
[   18.375593] usbcore: registered new interface driver pac207
[   18.389827] usbcore: registered new interface driver pac7311
[   18.405831] usbcore: registered new interface driver se401
[   18.427083] usbcore: registered new interface driver gspca_sn9c20x
[   18.468723] usbcore: registered new interface driver sonixb
[   18.506675] usbcore: registered new interface driver sonixj
[   18.535654] usbcore: registered new interface driver spca500
[   18.565427] usbcore: registered new interface driver spca501
[   18.575356] usbcore: registered new interface driver spca506
[   18.605274] usbcore: registered new interface driver spca508
[   18.627200] usbcore: registered new interface driver spca561
[   18.665277] usbcore: registered new interface driver sq905
[   18.691580] usbcore: registered new interface driver sq905c
[   18.711906] usbcore: registered new interface driver stk014
[   18.737236] usbcore: registered new interface driver STV06xx
[   18.755827] usbcore: registered new interface driver sunplus
[   18.769524] usbcore: registered new interface driver t613
[   18.787198] usbcore: registered new interface driver tv8532
[   18.805873] usbcore: registered new interface driver vc032x
[   18.855969] usbcore: registered new interface driver gspca_zc3xx
[   18.916643] usbcore: registered new interface driver huawei_cdc_ncm
[   19.287203] PPP generic driver version 2.4.2
[   19.314987] NET: Registered protocol family 24
[   19.321924] PPTP driver version 0.8.5
[   19.346370] usbcore: registered new interface driver Philips webcam
[   19.375509] usbcore: registered new interface driver qmi_wwan
[   19.398196] usbcore: registered new interface driver rndis_host
[   19.427633] usbcore: registered new interface driver sierra
[   19.433476] usbserial: USB Serial support registered for Sierra USB modem
[   19.456643] usbcore: registered new interface driver sierra_net
[   19.504953] uvcvideo: Found UVC 1.00 device Microsoft LifeCam VX-800 (045e:07
[   19.551406] input: Microsoft LifeCam VX-800 as /devices/platform/ehci-platfor
[   19.562372] usbcore: registered new interface driver uvcvideo
[   19.568251] USB Video Class driver (1.1.1)
[   19.706703] usbcore: registered new interface driver cdc_mbim
[   19.737266] usbcore: registered new interface driver conex
[   19.765735] usbcore: registered new interface driver etoms
[   19.795698] usbcore: registered new interface driver finepix
[   19.827269] usbcore: registered new interface driver gspca_gl860
[   19.856413] usbcore: registered new interface driver jeilinj
[   19.881962] usbcore: registered new interface driver konica
[   19.916148] usbcore: registered new interface driver ALi m5602
[   19.964587] usbcore: registered new interface driver option
[   19.970355] usbserial: USB Serial support registered for GSM modem (1-port)
[   19.978417] option 1-1.4:1.0: GSM modem (1-port) converter detected
[   19.985139] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB0
[   19.992719] option 1-1.4:1.3: GSM modem (1-port) converter detected
[   19.999380] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB1
[   20.006566] option 1-1.4:1.4: GSM modem (1-port) converter detected
[   20.013278] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB2
[   20.156481] usbcore: registered new interface driver qcserial
[   20.162440] usbserial: USB Serial support registered for Qualcomm USB modem
[   20.327332] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[   20.334297] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   20.359766] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[   20.573473] kmodloader: done loading kernel modules from /etc/modules.d/*
[   26.532753] random: crng init done
[   26.536218] random: 6 urandom warning(s) missed due to ratelimiting
[   33.290987] EXT4-fs (sdc1): recovery complete
[   33.295464] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   36.215220] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   39.308305] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   41.028295] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   42.738481] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   42.850104] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   42.872650] br-lan: port 1(eth0.1) entered blocking state
[   42.878204] br-lan: port 1(eth0.1) entered disabled state
[   42.884130] device eth0.1 entered promiscuous mode
[   42.889000] device eth0 entered promiscuous mode
[   42.931178] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   43.004818] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   43.874202] eth0: link up (1000Mbps/Full duplex)
[   43.879008] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   43.952855] br-lan: port 1(eth0.1) entered blocking state
[   43.958347] br-lan: port 1(eth0.1) entered forwarding state
[   43.964216] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   44.085268] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   47.767819] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   49.161597] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   49.190766] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   49.316602] br-lan: port 2(wlan1) entered blocking state
[   49.322006] br-lan: port 2(wlan1) entered disabled state
[   49.328006] device wlan1 entered promiscuous mode
[   49.332933] br-lan: port 2(wlan1) entered blocking state
[   49.338331] br-lan: port 2(wlan1) entered forwarding state
[   49.397067] br-lan: port 3(wlan0) entered blocking state
[   49.402523] br-lan: port 3(wlan0) entered disabled state
[   49.408506] device wlan0 entered promiscuous mode
[   50.364264] br-lan: port 2(wlan1) entered disabled state
[   52.782720] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   52.789371] br-lan: port 3(wlan0) entered blocking state
[   52.794838] br-lan: port 3(wlan0) entered forwarding state
[   52.981483] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   52.988332] br-lan: port 2(wlan1) entered blocking state
[   52.993783] br-lan: port 2(wlan1) entered forwarding state
[   54.770761] 3g-wan: renamed from ppp0
[   56.633101] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[   95.624769] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[   95.632022]                old minutes west=0, new minutes west=-120


***************************************
*     U-Boot 1.1.4-7a540a78-clean     *
*          Build: 2018-02-23          *
***************************************

** Warning: bad env CRC, using default,
   use 'saveenv' to save it in FLASH

** Warning: reset caused by watchdog!

  BOARD: TP-Link TL-WDR3600 v1
    SOC: AR9344 rev. 2
    CPU: MIPS 74Kc
    RAM: 128 MB DDR2 32-bit CL3-4-4-10
  FLASH: 16 MB Winbond W25Q128
   PCIe: 168C:0033
    MAC: 64:70:02:D1:67:62
 CLOCKS: CPU/RAM/AHB/SPI/REF
         550/400/200/ 25/ 40 MHz

Hit any key to stop booting:  0

Booting image from 0x9F020000...

   Vendor/image name:    OpenWrt r7935-d08a63770c
   Hardware ID:          0x36000001
   Whole image size:     7.8 MB (8126464 bytes)
   Kernel size:          1.3 MB (1385806 bytes)
   Rootfs size:          5.7 MB (5958384 bytes)
   Kernel load address:  0x80060000
   Kernel entry point:   0x80060000

   Header CRC...  skipped
   Data CRC...    skipped

Stopping network... OK!
Uncompressing Kernel... OK!
Starting kernel...

[    0.000000] Linux version 4.9.206 (cezary@eko.one.pl) (gcc version 7.3.0 (Ope
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag
[    0.000000] Kernel command line:  board=TL-WDR4300  console=ttyS0,115200 root
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.00
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i
[    0.000010] sched_clock: 32 bits at 275MHz, resolution 3ns, wraps every 78090
[    0.008721] Calibrating delay loop... 274.02 BogoMIPS (lpj=1370112)
[    0.081683] pid_max: default: 32768 minimum: 301
[    0.086950] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.105220] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma
[    0.116230] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.124381] NET: Registered protocol family 16
[    0.130974] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[    0.140733] registering PCI controller with io_map_base unset
[    0.396049] PCI host bridge to bus 0000:00
[    0.400681] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.408345] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.414571] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.422136] pci_bus 0000:00: No busn resource found for root bus, will use [b
[    0.431024] pci 0000:00:00.0: invalid calibration data
[    0.437204] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bi
[    0.445405] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref
[    0.453465] pci 0000:00:00.0: using irq 40 for pin 1
[    0.462639] clocksource: Switched to clocksource MIPS
[    0.469471] NET: Registered protocol family 2
[    0.475377] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.483215] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.490315] TCP: Hash tables configured (established 1024 bind 1024)
[    0.497501] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.504060] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.511315] NET: Registered protocol family 1
[    0.519394] Crashlog allocated RAM at address 0x3f00000
[    0.526503] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.541099] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.547646] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT
[    0.569036] io scheduler noop registered
[    0.573461] io scheduler deadline registered (default)
[    0.579656] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.589699] console [ttyS0] disabled
[    0.613796] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 250
[    0.623434] console [ttyS0] enabled
[    0.623434] console [ttyS0] enabled
[    0.630849] bootconsole [early0] disabled
[    0.630849] bootconsole [early0] disabled
[    0.646131] m25p80 spi0.0: found w25q128, expected m25p80
[    0.660776] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.665930] 5 tp-link partitions found on MTD device spi0.0
[    0.671585] Creating 5 MTD partitions on "spi0.0":
[    0.676487] 0x000000000000-0x000000020000 : "u-boot"
[    0.683668] 0x000000020000-0x000000172750 : "kernel"
[    0.690903] 0x000000172750-0x000000ff0000 : "rootfs"
[    0.697751] mtd: device 2 (rootfs) set to be root filesystem
[    0.703592] 1 squashfs-split partitions found on MTD device rootfs
[    0.709877] 0x000000730000-0x000000ff0000 : "rootfs_data"
[    0.717741] 0x000000ff0000-0x000001000000 : "art"
[    0.724809] 0x000000020000-0x000000ff0000 : "firmware"
[    0.733402] libphy: Fixed MDIO Bus: probed
[    0.748834] switch0: Atheros AR8327 rev. 4 switch registered o

Co poradzicie?

2020-04-02 22:43:37

Witam, wpadł mi w ręce taki stary minikomputer (nie mam pojęcia czy sprawny)
https://www.embeddedarm.com/products/TS-7250

Jak podłącze zasilanie świeci się na płytce zielona dioda czesem mignie czerwona. W instrukcji udało mi się wyczytać że aby cokolwiek w nim zobaczyć/ skonfigurować trzeba się podłączyć przez złącze com (db9) jak podłącze się z zalecanymi ustawianiami w terminalu minicom po podłączeniu zasilania zmienia sie status na online, ale konsola zupełnie nic nie wypisuje.
wyczytałem między innymi że zworką 1 można ustawić czy ma być boot automatycznie z debian lub też nie.
Ma port rj45 ale router go nie wykrywa, diody też ciemne (może trzeba skonfigurować Ethernet (w instrukcji coś b←ło o konfiguracji sieci)

Czy raczej do kosza?
tu jest instrukcja https://www.embeddedarm.com/documentati … manual.pdf
Ja niestety muszę sie posiłkować tłumaczem Google więc całej nawet nie próbuje przeczytać.

Może ktoś z Was miał styczność z czymś podobnym i wie czy raczej trup, czy można jeszcze się dostać jakoś do tej konsoli ?

2020-04-02 04:45:29

steel_rat napisał/a:

drk napisał/a:
steel_rat napisał/a:
Mój patent jest taki, że buduję sam sobie openwrt z potrzebnymi pakietami (mam taki duży flash). Zaznaczam opcję zachowania danych i tyle.
Niestety przy zwykłej instalacji i aktualizacji openwrt już ten myk nie będzie działał. Ponieważ niektóre pakiety wymagają konkretnej wersji buildu. Nie zadziałają one na innej.
Mam kilka routerów więc budowanie dla każdego osobnego openwrt to trochę za grubo dla mnie, poza tym zakładam, że w buildach od Cezarego nic nie brakuje, a ja bym na pewno coś spartolił i coś by mi nie działało
steel_rat napisał/a:
Dlatego lepiej sobie zrobić listę i zainstalować z listy
że na papierze tudzież w notatniku?
Czemu nie. Robisz listę jakie pakiety masz typu
opkg update
opkg install nano
opkg install vi
...
Wklejasz w terminal i instalujesz.

A jeśli bym zainstalował całkiem nową i inną wersję openwrt ale ze starej skopiował pliki dla dodatkowych pakietów i tych standardowych (z /etc/config) To te zastępując plik np motion. conf lub innego pakietu to wówczas może się coś pochrzanić?

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Opcje wyszukiwania (Strona 8 z 14)

Znalezione posty: 176 do 200 z 345

176 Odpowiedź przez arek1194 2020-04-09 18:09:25

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

177 Odpowiedź przez arek1194 2020-04-09 17:22:33

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

178 Odpowiedź przez arek1194 2020-04-09 14:29:40

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

179 Odpowiedź przez arek1194 2020-04-09 14:16:54

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

180 Odpowiedź przez arek1194 2020-04-09 12:51:20

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

181 Odpowiedź przez arek1194 2020-04-09 12:27:13

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

182 Odpowiedź przez arek1194 2020-04-09 10:27:43

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

183 Odpowiedź przez arek1194 2020-04-09 07:56:59

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

184 Odpowiedź przez arek1194 2020-04-09 07:35:47

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

185 Odpowiedź przez arek1194 2020-04-08 22:52:27

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

186 Odpowiedź przez arek1194 2020-04-08 22:24:27

Odp: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

187 Temat przez arek1194 2020-04-08 22:03:40

Temat: WDR3600 i sterowanie GPIO (40 odpowiedzi, napisanych Sprzęt / Hardware)

188 Odpowiedź przez arek1194 2020-04-06 21:23:11

Odp: Bus embedded TS-7250 stary minikomputer. Czy da się to uruchomić (9 odpowiedzi, napisanych Mini komputery)

189 Odpowiedź przez arek1194 2020-04-06 20:51:10

Odp: Bus embedded TS-7250 stary minikomputer. Czy da się to uruchomić (9 odpowiedzi, napisanych Mini komputery)

190 Odpowiedź przez arek1194 2020-04-06 20:36:22

Odp: Bus embedded TS-7250 stary minikomputer. Czy da się to uruchomić (9 odpowiedzi, napisanych Mini komputery)

191 Odpowiedź przez arek1194 2020-04-06 17:56:38

Odp: Bus embedded TS-7250 stary minikomputer. Czy da się to uruchomić (9 odpowiedzi, napisanych Mini komputery)

192 Odpowiedź przez arek1194 2020-04-05 09:31:27

Odp: WDR 3600 resetuje się (nie zawsze) Proszę spojrzeć na log (10 odpowiedzi, napisanych Sprzęt / Hardware)

193 Odpowiedź przez arek1194 2020-04-05 08:58:04

Odp: WDR 3600 resetuje się (nie zawsze) Proszę spojrzeć na log (10 odpowiedzi, napisanych Sprzęt / Hardware)

194 Odpowiedź przez arek1194 2020-04-04 22:48:03

Odp: WDR 3600 resetuje się (nie zawsze) Proszę spojrzeć na log (10 odpowiedzi, napisanych Sprzęt / Hardware)

195 Odpowiedź przez arek1194 2020-04-04 22:16:40

Odp: WDR 3600 resetuje się (nie zawsze) Proszę spojrzeć na log (10 odpowiedzi, napisanych Sprzęt / Hardware)

196 Odpowiedź przez arek1194 2020-04-04 21:43:47

Odp: WDR 3600 resetuje się (nie zawsze) Proszę spojrzeć na log (10 odpowiedzi, napisanych Sprzęt / Hardware)

197 Odpowiedź przez arek1194 2020-04-04 21:42:19

Odp: WDR 3600 resetuje się (nie zawsze) Proszę spojrzeć na log (10 odpowiedzi, napisanych Sprzęt / Hardware)

198 Temat przez arek1194 2020-04-04 20:32:11

Temat: WDR 3600 resetuje się (nie zawsze) Proszę spojrzeć na log (10 odpowiedzi, napisanych Sprzęt / Hardware)

199 Temat przez arek1194 2020-04-02 22:43:37

Temat: Bus embedded TS-7250 stary minikomputer. Czy da się to uruchomić (9 odpowiedzi, napisanych Mini komputery)

200 Odpowiedź przez arek1194 2020-04-02 04:45:29

Odp: Jak aktualizować OpenWRT, żeby zachować konfigurację i ekstra pakiety? (12 odpowiedzi, napisanych Oprogramowanie / Software)

Znalezione posty: 176 do 200 z 345