Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Posty przez stich86
Jak sobie wyłączyłeś wcześniej to po aktualizacji B12 znów to włączy bez twojej wiedzy. I trzeba znów wyłączyć.
Ok.. nice to know 
Okay. Or what exactly should I test. 5GHz radio right? I have to rip those partitions with tricks too, is it unnecessary?
No more, I’ve extracted them from mtd17 dump
Test if you are getting correct speed (866mbps @ 80mhz)
Tak informacyjnie - aktualizacja do B12 włącza sama agregację upload.
ULCA is started working from B03
Maybe on Vodafone BTS Cellock is not possible on any modem ?
I.E. in polish Play there is exacly the same issue , not posible to do CA with Cellock on any modem.
But MF289F module is working with CA and cell lock
A friend of mine has updated to B12, but CA with cell lock on Vodafone BTS still doesn’t work 
MiG25 napisał/a:ak ktoś ma plik upgrade.zip B11 na B12 , to niech wrzuci , sam modem sobie zupdejtuje dla zasady.
Thanks for sharing.. so I’ve to avoid doing all OTA stuff
Wg włochów i kolegi @stich86 żadnych widocznych zmian nie ma.
Jak ktoś ma plik upgrade.zip B11 na B12 , to niech wrzuci , sam modem sobie zupdejtuje dla zasady.
I’ll share it on Monday
Hope they have fix cell lock and CA..
describe this trick and I will try do
ok i was able to extract the ubifs, the 5G board data of your firmware is the same of VFDE dump (AT2 ver), so you should not have any issue on 5.8G band
Have you done other tests?
let me know
thanks
@stich86 i tried your last build ,and
- configs for @IceG extensions have still default ttyUSB0 ( i remember you tried to "personalize " it)
- Physically ports are mixed/crossed ( you have to connect to upper port to receive IP from router , while lower port is waiting for IP - is WAN) , WAN is assigned as eth1 - with should be LAN( should be eth1)....- did you figure out to reset modem without reseting router it self ?
- did ou notice ,that in MF286D and MF286F ,when you set a channel 132 clients are connecting onl in 40MHz wide ( router it self is saying that channel can be 80MHz) , same situation is on ofw's.... Seting channels like 100 , 149 are ok.
- Set of channel 165 is not possible (even when you set to US) ,so maybe there is a way to cut it from channels list....
i'll try to responde to each question:
- yes, i've configured using custom etc, but looks like it doesn't work.. shoud i dig why
- currently it's stock configuration as OpenWRT, also stock image of MF286D is configured in this way, only EKO build are configured correctly
- not yet, only way ATM is to use AT+CFUN=1 to reset the baseband and avoid all router reboot
- not tried, but here we have to do test on both AT1\AT2 becasue there is a QCA9984 that is very different from IPA4019 5.8G
- not tried, also there i'll check it with my other friends with AT2 rev
describe this trick and I will try do
Read my last msg 
In initram try to do:
ubiattach -m 17
Then backup /dev/ubi0_1 or something like that
Because with initramfs you have to do ubiattach
I’ll try to extract ubifs with tools..
Otherwise you have to do some tricks to backup under OFW
But in my version is only 0-19 mtd partition
I understand you mean this command should show all partition yes?
cat /proc/mtd
Please share a cat /proc/mtd
stich so mtd20 or mt21 you want?
Mtd21
And about name wifi and password from label where is on which partition?
They should be on mtd12 (cfg-param)
Does the mtd20 partition have sensitive mac imei etc data? I haven't analyzed it yet, that's why I am asking
No it’s the rootfs explosed from UBI inside mtd17
My fault it’s mtd21, mtd20 is the kernel
MAC data is inside ART (mtd9), IMEI is on the module not on the router
Też testowałem "kody krótkie" cokolwiek to miało znaczyć - rozumiem że w mniemaniu programisty miały to być USSD ale nie działają na mojej sztuce też. Nawet nie mrugnie żeby przejść na 3g. Bo nie wiem czy u nas w Polsce już zrobili obsługę ussd po lte. Na E3276 na pewno zrzuca do 3g a potem z automatu wraca. Pod openwrt przypuszczam że będzie lux. Jutro MiGu sprawdzę jeszcze raz ten tryb. Na razie z tydzień lub 2 ma mi wyświetlić uptime i stabilność. Jak będzie ok to mogę testować openwrt. Sprawdzałeś na swojej sztuce Rj11?
Please share also mtd20
Regarding RJ11 on VFIT/VFDE version is working but on IT it’s necessary to change a parameter on the module that is using VoIP and not CS
AT+ZCDRUN=E gives acutally , PID 0016....
You were right… my fault
We should digging on the module mode to understand why it uses this PID
stich86 napisał/a:if it's in three port 3 port mode without RDNIS yes, otherwise it's 1485
So you are able to change mode to be without RDNDIS ?
not on this modem (i'm talking about 1485), i'm talking about MF286D module.
Essentialy it's the command "AT+ZCDRUN=E\F" to switch modes (it deletes a file into EFS)
mtd16
https://www.easypaste.org/file/dItb30Yk … in?lang=pl
mtd17
https://www.easypaste.org/file/RKXiwn0f … in?lang=pl
trzeba wybrać wolny transfer żeby było za free
are you able to share also and mtd20 backup? so i've already the root fs without needs to install ubi_fs tools
smereka napisał/a:Przejrzałem wszystkie zakładki. Nie znalazłem trybu bridge
Szkoda... No powinien być tam do ustawienia , gdzie w MF286D , czyli na głównym panelu , z napisem tryb ,czy jakoś tak.
stich86 napisał/a:Cezary napisał/a:Jeżeli radio jest na ipq to z kolei jak AT2, czyli 2x2. Na qca miał radio 4x4.
ZTE si funny… so this is a third combination:
Modem PID/VID like MF289F AT1, but AT2 router board
May be is related to modem software (PID/VID are configured inside android os of the module)
I remember i had also MF286D , with PID also changed to 1432 , when it was connected to laptop....( in PCB of MF286D it was 1485..) , i didn't care at that time :
https://eko.one.pl/forum/viewtopic.php? … 13#p256213
if it's in three port 3 port mode without RDNIS yes, otherwise it's 1485
@stich86 , this is part of printenv:
lc=tftpboot 0x84000000 ${dir}cdt-AP.DK04.1-C1.bin&&sf probe&&sf erase 0xc0000 +$filesize&&sf write $fileaddr 0xc0000 $filesize lp=tftpboot 0x84000000 ${dir}norplusnand-system-partition-ipq40xx.bin&&sf probe&&sf erase 0x40000 +$filesize&&sf write $fileaddr 0x40000 $filesize lr=tftpboot 0x84000000 ${dir}root_uImage&&nand erase 0x1000000 0x800000 &&nand write_partition 0x84000000 0x1000000 0x800000 &&nand erase 0x1800000 0x1D00000 &&nand write_partition 0x84800000 0x1800000 0x1D00000 lrb=tftpboot 0x84000000 ${dir}delta.bin&&nand erase 0x3500000 0x1900000&&nand write $fileaddr 0x3500000 $filesize lrs=tftpboot 0x84000000 ${dir}root_uImage_s&&nand erase 0x1800000 0x1D00000&&nand write $fileaddr 0x1800000 $filesize lu=tftpboot 0x84000000 ${dir}uboot.bin&&sf probe&&sf erase 0xf0000 +$filesize&&sf write $fileaddr 0xf0000 $filesize lw=tftpboot 0x84000000 ${dir}web.img&&nand erase 0x1000000 0x800000&&nand write $fileaddr 0x1000000 $filesizeAs you can see for root_uImage there are two times erase ( first for web.img and second for root_uImage_s ) , and in your description there is only first one ( and comment "This will erase RootFS+Web" with is partial true
thx for information
i've changed descriptions on my git and on PR
Can you share some screenshot of the web interface?
Thx
Lucynka po ustawieniu wifi faktycznie pokazuje mi max 433 na 80MHz więcej tam ustawić nie mogę. Pewnie sysupgrade by rozwiązał sprawie. Right stich?
If think initramfs doesn’t have custom firmare, or you have a different board.
If you can share mtd17 I can check if the 5G firmware is equal to other AT2 version..
Jeżeli radio jest na ipq to z kolei jak AT2, czyli 2x2. Na qca miał radio 4x4.
ZTE si funny… so this is a third combination:
Modem PID/VID like MF289F AT1, but AT2 router board
May be is related to modem software (PID/VID are configured inside android os of the module)
eko.one.pl → Posty przez stich86
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc
