Wróciłem do konfiguracji pci-e dla 5ghz + mini pci-e 2,4ghz bo przynajmniej mam sieć 5ghz po rebootach.
Cezary - poniżej logi po włączeniu i wyłączeniu karty AR5B125, która nie rozgłasza ssid, mimo, że w gui wszystko wygląda ok.
Fri Mar 10 17:09:19 2017 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Fri Mar 10 17:09:19 2017 kern.info kernel: [36539.107434] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Fri Mar 10 17:09:19 2017 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Fri Mar 10 17:09:19 2017 daemon.err hostapd: Using interface wlan1 with hwaddr <mac mojej karty> and ssid "Rp24"
Fri Mar 10 17:09:19 2017 kern.info kernel: [36539.133972] device wlan1 entered promiscuous mode
Fri Mar 10 17:09:19 2017 kern.info kernel: [36539.189658] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Fri Mar 10 17:09:19 2017 kern.info kernel: [36539.189861] br-lan: port 3(wlan1) entered forwarding state
Fri Mar 10 17:09:19 2017 kern.info kernel: [36539.190025] br-lan: port 3(wlan1) entered forwarding state
Fri Mar 10 17:09:19 2017 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED
Fri Mar 10 17:09:19 2017 daemon.notice hostapd: wlan1: AP-ENABLED
Fri Mar 10 17:09:19 2017 daemon.notice netifd: Network device 'wlan1' link is up
Fri Mar 10 17:09:21 2017 kern.info kernel: [36541.188965] br-lan: port 3(wlan1) entered forwarding state
Fri Mar 10 17:15:45 2017 kern.info kernel: [36925.270679] device wlan1 left promiscuous mode
Fri Mar 10 17:15:45 2017 kern.info kernel: [36925.270834] br-lan: port 3(wlan1) entered disabled state
Fri Mar 10 17:15:45 2017 daemon.notice hostapd: wlan1: interface state ENABLED->DISABLED
Fri Mar 10 17:15:45 2017 daemon.notice hostapd: wlan1: AP-DISABLED
Fri Mar 10 17:15:45 2017 daemon.notice hostapd: wlan1: CTRL-EVENT-TERMINATING
Fri Mar 10 17:15:45 2017 daemon.notice hostapd: nl80211: deinit ifname=wlan1 disabled_11b_rates=0
Fri Mar 10 17:15:45 2017 daemon.notice hostapd: nl80211: Failed to remove interface wlan1 from bridge br-lan: Invalid argumentoraz info o samej karcie
TP-WN721N iw phy0 info
root@RobP:~# iw phy1 info
Wiphy phy1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x1 RX 0x1
Configured Antennas: TX 0x1 RX 0x1
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
* outside context of a BSS
Band 1:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-7
Frequencies:
* 2412 MHz [1] (16.0 dBm)
* 2417 MHz [2] (16.0 dBm)
* 2422 MHz [3] (16.0 dBm)
* 2427 MHz [4] (16.0 dBm)
* 2432 MHz [5] (16.0 dBm)
* 2437 MHz [6] (16.0 dBm)
* 2442 MHz [7] (16.0 dBm)
* 2447 MHz [8] (16.0 dBm)
* 2452 MHz [9] (16.0 dBm)
* 2457 MHz [10] (16.0 dBm)
* 2462 MHz [11] (16.0 dBm)
* 2467 MHz [12] (16.0 dBm)
* 2472 MHz [13] (16.0 dBm)
* 2484 MHz [14] (disabled)
valid interface combinations:
* #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
