Udało mi się podłączyć pod urządzonko,
Na samym końcu log bez dotykania urzązenia, do końca procesu bootowania.
Pierwszy log to boot menager, pytanie - jaki obraz wrzucić, możecie coś polecić?
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.03.10 14:19:05 =~=~=~=~=~=~=~=~=~=~=~=
HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 5.38 for BCM96328 (32bit,SP,BE)
Build Date: Fri Jul 22 18:54:17 CST 2011 (cookiechen@SZ01007.DONGGUAN.CN)
Copyright (C) 2005-2010 SAGEM Corporation.
HS Serial flash device: name S25FL064, id 0x0116 size 8192KB
Total Flash size: 8192K with 128 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-5) : F@ST2704V2
Number of MAC Addresses (1-32) : 11
Base MAC Address : c0:ac:54:5c:29:b4
PSI Size (1-64) KBytes : 40
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 111
CFE>
web info: Waiting for connection on socket 0.[J
CFE> help
Available commands:
u change customer name.
d [d]isplay the content of [p]si or [b]ackup or [c]ustomer name or s[e]rial number or h[w] version of the [v]ersion of cfe.
w Write the whole image start from beginning of the flash
e Erase [n]vram or [a]ll flash except bootrom
r Run program from flash image or from host depend on [f/h] flag
f Write image to the flash
b Change board parameters
reset Reset the board
help Obtain help for CFE commands
For more information about a command, enter 'help command-name'
*** command status = 0
CFE> =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.03.10 14:06:35 =~=~=~=~=~=~=~=~=~=~=~=
HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 5.38 for BCM96328 (32bit,SP,BE)
Build Date: Fri Jul 22 18:54:17 CST 2011 (cookiechen@SZ01007.DONGGUAN.CN)
Copyright (C) 2005-2010 SAGEM Corporation.
HS Serial flash device: name S25FL064, id 0x0116 size 8192KB
Total Flash size: 8192K with 128 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-5) : F@ST2704V2
Number of MAC Addresses (1-32) : 11
Base MAC Address : c0:ac:54:5c:29:b4
PSI Size (1-64) KBytes : 40
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (cookiechen@SZ01007.DONGGUAN.CN) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Fri Jul 22 18:37:52 CST 2011
HS Serial flash device: name S25FL064, id 0x0116 size 8192KB
F@ST2704V2 prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 8031df20, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60384k/64512k available (2609k kernel code, 4108k reserved, 523k data, 124k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 816 bytes
NET: Registered protocol family 16
Total Flash size: 8192K with 128 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 117
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
generic_probe wake up Monitor!!
message received before monitor task is initialized kerSysSendtoMonitorTask
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
generic_probe wake up Monitor!!
message received before monitor task is initialized kerSysSendtoMonitorTask
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
brcmboard: brcm_board_init entry
kerSysScreenPciDevices: 0x14e4:0x6300:(slot 9) detected
kerSysScreenPciDevices: 0x14e4:0x6300:(slot 10) detected
kerSysScreenPciDevices: 0x14e4:0x6328:(slot 0) detected
kerSysScreenPciDevices: 0x14e4:0xa8d8:(slot 0) detected
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x800a is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Jul 22 2011 18:35:05
Broadcom Logger v0.1 Jul 22 2011 18:33:31
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 124k freed
init started: BusyBox v1.00 (2011.07.22-10:40+0000) multi-call binary
BusyBox v1.00 (2011.07.22-10:40+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Broadcom Packet Flow Cache Char Driver v2.1 Mar 18 2010 21:39:51 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Mar 18 2010 21:39:50
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6328B0 Ethernet Network Device v0.1 Jul 22 2011 18:33:38
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: C0:AC:54:5C:29:B4
eth1: MAC Address: C0:AC:54:5C:29:B4
eth2: MAC Address: C0:AC:54:5C:29:B4
eth3: MAC Address: C0:AC:54:5C:29:B4
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom strapped
wl:(srom strapped) probe/present=0
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43225_map.bin
wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.11.cpe4.406.4
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Broadcom 802.1Q VLAN Interface, v0.1
===== Release Version 5.38 (build timestamp 110722_1839) =====
Got primary config file from flash (len=34074), validating....
device eth2 entered promiscuous mode
ip_tables: (C) 2000-2006 Netfilter Core Team
device eth3 entered promiscuous mode
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
BcmAdsl_Initialize=0xC00D8178, g_pFnNotifyCallback=0xC0100B44
WLmngr Daemon is running
optarg=0 shmId=0
pSdramPHY=0xA3FFFFF8, 0x12AEC 0xDEADBEEF
*** XfaceOffset: 0x21F90 => 0x21F90 ***
wlevt_init@107: opened loopback socket 4
wlevt is ready for new msg...
*** PhySdramSize got adjusted: 0x82CBC => 0x98660 ***
AdslCoreSharedMemInit: shareMemAvailable=424320
AdslCoreHwReset: pLocSbSta=82de8000 bkupThreshold=1600
AdslCoreHwReset: AdslOemDataAddr = 0xA3F77D08
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ssk:error:12.543:rcl_wanDebugPortMirroringCfgObject:93:Fail to get iidStack for monitorInterface=atm1
ssk:error:12.544:mdm_activateObjects:620:rcl handler reports error=9002 on X_BROADCOM_COM_DebugPortMirroringCfg {27}
ssk:error:12.547:rcl_wanDebugPortMirroringCfgObject:93:Fail to get iidStack for monitorInterface=atm1
ssk:error:12.547:mdm_activateObjects:620:rcl handler reports error=9002 on X_BROADCOM_COM_DebugPortMirroringCfg {28}
insmod: cannot open module `/lib/modules/2.6.30/kernel/net/netfilter/nf_conntrack_sip.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.30/kernel/net/ipv4/netfilter/nf_nat_sip.ko': No such file or directory
/usr/twonkymedia/twonkymedia: /usr/twonkymedia/twonkymediaserver started, pid = 601
TWONKY started---/usr/twonkymedia/twonkymedia -inifile /var/twonkymedia/ini/twonky.ini
monitor task is initialized pid= 251
TwonkyMedia Version 4.4.18
LOG_SYSTEM: reading ini file: "/var/twonkymedia/ini/twonky.ini".
===> DecodedPPPDR:
wl0.1 (): not using net_device_ops yet
wl0.2 (): not using net_device_ops yet
wl0.3 (): not using net_device_ops yet
WLMNGR-DAEMON:error:19.692:rcl_l2BridgingFilterObject:329:unexpected change in bridge ref, from -1 to -1
WLMNGR-DAEMON:error:19.696:rcl_l2BridgingFilterObject:329:unexpected change in bridge ref, from -1 to -1
WLMNGR-DAEMON:error:19.701:rcl_l2BridgingFilterObject:329:unexpected change in bridge ref, from -1 to -1
WLMNGR-DAEMON:error:19.707:rcl_l2BridgingFilterObject:329:unexpected change in bridge ref, from -1 to -1
