Hejka
Wygrzebałem z szafy iconnecta w którym było wgrane alternatywne oprogramowanie.
Niestety nie pamiętam czy było to Openwrt czy Debian.

Po uruchomieniu iconnecta nie można się do niego zalogować dioda zasilania pali się na niebiesko i mruga na czerwono.
Podłączyłem adapter USB do płytki i niestety na terminalu wyświetlają się krzaki.
Próbowałem wgrać oryginalny software ale operacja kończy się na ciągłym świeceniu na czerwono diody zasilania.
Czy można jeszcze coś zrobić czy awaria jest nieodwracalna?

Pozdrawiam

Podłączyłeś gnd dobrze?

Do 3 pinu zgodnie z https://wiki.openwrt.org/toh/iomega/iconnect

Masz krzaki, więc albo prędkość masz złą, albo nie styka coś.

Po ponownym podłączeniu to i krzaków brak (kilka resetów zrobiłem i baterię na chwilę odłączyłem).
Prędkość to 9600?

115200

Po zmianie prędkości nastała jasność czyli komunikaty są jak poniżej

"
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25

Mapower version: iConnect 2.1 (512MB) (2010/02/02)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x200000
2097152 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-3.0.17
Created: 2012-03-01 17:42:02 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1005360 Bytes = 981.8 kB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 3.0.17 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Thu Mar 1 18:42:00 CET 2012
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Iomega iConnect Wireless Data Station
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 panic=30 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 257044k/257044k available, 5100k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xfe800000 ( 736 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0025000 ( 116 kB)
[ 0.000000] .text : 0xc0025000 - 0xc029a000 (2516 kB)
[ 0.000000] .data : 0xc029a000 - 0xc02b2740 ( 98 kB)
[ 0.000000] .bss : 0xc02b2764 - 0xc02bf8d8 ( 53 kB)
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 6.834959] Calibrating delay loop... 990.41 BogoMIPS (lpj=4952064)
[ 6.874930] pid_max: default: 32768 minimum: 301
[ 6.875090] Mount-cache hash table entries: 512
[ 6.875433] CPU: Testing write buffer coherency: ok
[ 6.878021] NET: Registered protocol family 16
[ 6.880187] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 6.880203] Feroceon L2: Enabling L2
[ 6.880244] Feroceon L2: Cache support initialised.
[ 6.882689] Kirkwood PCIe port 0:
[ 6.882699] link up
[ 6.882707] PCI: bus0 uses PCIe port 0
[ 6.883174] PCI: bus0: Fast back to back transfers disabled
[ 6.883565] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff]
[ 6.883587] pci 0000:00:01.0: BAR 0: set to [mem 0xe0000000-0xe000ffff] (PCI address [0xe0000000-0xe000ffff])
[ 6.886278] bio: create slab <bio-0> at 0
[ 6.887915] Switching to clocksource orion_clocksource
[ 6.889672] NET: Registered protocol family 2
[ 6.889799] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 6.890108] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 6.890330] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 6.890444] TCP: Hash tables configured (established 8192 bind 8192)
[ 6.890455] TCP reno registered
[ 6.890467] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 6.890494] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 6.890747] NET: Registered protocol family 1
[ 6.896804] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 6.896822] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 6.897179] msgmni has been set to 502
[ 6.897490] io scheduler noop registered
[ 6.897501] io scheduler deadline registered (default)
[ 7.063417] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 7.085130] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 7.413730] console [ttyS0] enabled
[ 7.425619] brd: module loaded
[ 7.429723] ONFI flash detected
[ 7.433048] NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
[ 7.441556] Scanning device for bad blocks
[ 7.584411] Bad eraseblock 2372 at 0x000012880000
[ 7.657001] Bad eraseblock 3533 at 0x00001b9a0000
[ 7.694606] Creating 3 MTD partitions on "orion_nand":
[ 7.699782] 0x000000000000-0x000000100000 : "u-boot"
[ 7.706181] 0x000000100000-0x000000300000 : "uImage"
[ 7.712446] 0x000000300000-0x000020000000 : "rootfs"
[ 7.719731] UBI: attaching mtd2 to ubi0
[ 7.723593] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 7.729912] UBI: logical eraseblock size: 129024 bytes
[ 7.735334] UBI: smallest flash I/O unit: 2048
[ 7.740071] UBI: sub-page size: 512
[ 7.744710] UBI: VID header offset: 512 (aligned 512)
[ 7.750578] UBI: data offset: 2048
[ 8.149371] UBI: max. sequence number: 4474878
[ 8.164293] UBI: attached mtd2 to ubi0
[ 8.168104] UBI: MTD device name: "rootfs"
[ 8.173175] UBI: MTD device size: 509 MiB
[ 8.178173] UBI: number of good PEBs: 4070
[ 8.182897] UBI: number of bad PEBs: 2
[ 8.187361] UBI: number of corrupted PEBs: 0
[ 8.191835] UBI: max. allowed volumes: 128
[ 8.196474] UBI: wear-leveling threshold: 4096
[ 8.201209] UBI: number of internal volumes: 1
[ 8.205674] UBI: number of user volumes: 1
[ 8.210147] UBI: available PEBs: 0
[ 8.214611] UBI: total number of reserved PEBs: 4070
[ 8.219608] UBI: number of PEBs reserved for bad PEB handling: 38
[ 8.225730] UBI: max/mean erase counter: 8203/4647
[ 8.230551] UBI: image sequence number: 0
[ 8.234804] UBI: background thread "ubi_bgt0d" started, PID 673
[ 8.241888] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 8.248928] mv643xx_eth smi: probed
[ 8.254243] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:b8:12:02:5a
[ 8.263949] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 8.270265] cpuidle: using governor ladder
[ 8.276120] TCP westwood registered
[ 8.279659] NET: Registered protocol family 17
[ 8.284197] Bridge firewalling registered
[ 8.288477] 802.1Q VLAN Support v1.8
[ 8.293636] rtc-mv rtc-mv: setting system clock to 2014-06-16 21:13:14 UTC (1402953194)
[ 8.321558] UBIFS: recovery needed
[ 8.384946] UBIFS: recovery completed
[ 8.388655] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 8.394692] UBIFS: file system size: 517773312 bytes (505638 KiB, 493 MiB, 4013 LEBs)
[ 8.402743] UBIFS: journal size: 25933824 bytes (25326 KiB, 24 MiB, 201 LEBs)
[ 8.410448] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 8.416306] UBIFS: default compressor: lzo
[ 8.420432] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 8.426527] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 8.432630] Freeing init memory: 116K
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -

Please press Enter to activate this console. [ 13.115797] Compat-wireless backport release: compat-wireless-2012-02-23-9-g3e5b1f0
[ 13.123527] Backport based on wireless-testing.git master-2012-02-27
[ 13.156056] cfg80211: Calling CRDA to update world regulatory domain
[ 13.229124] cfg80211: World regulatory domain updated:
[ 13.234289] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.242536] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.250331] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.258125] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.265912] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.273698] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.327916] SCSI subsystem initialized
[ 13.356987] usbcore: registered new interface driver usbfs
[ 13.362629] usbcore: registered new interface driver hub
[ 13.369492] usbcore: registered new device driver usb
[ 13.489880] Button Hotplug driver version 0.4.1
[ 13.597727] PPP generic driver version 2.4.2
[ 13.661501] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.771173] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 13.777804] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 13.783168] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 13.817983] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 13.837954] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 13.844545] hub 1-0:1.0: USB hub found
[ 13.848349] hub 1-0:1.0: 1 port detected
[ 13.870909] nf_conntrack version 0.5.0 (4018 buckets, 16072 max)
[ 14.099876] xt_time: kernel timezone is -0000
[ 14.168043] usb 1-1: new high speed USB device number 2 using orion-ehci
[ 14.226085] i2c /dev entries driver
[ 14.262720] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 14.284275] usbcore: registered new interface driver usbserial
[ 14.290248] USB Serial support registered for generic
[ 14.329333] hub 1-1:1.0: USB hub found
[ 14.333854] hub 1-1:1.0: 4 ports detected
[ 14.338874] usbcore: registered new interface driver usbserial_generic
[ 14.345435] usbserial: USB Serial Driver core
[ 14.367281] Initializing USB Mass Storage driver...
[ 14.372368] usbcore: registered new interface driver usb-storage
[ 14.378419] USB Mass Storage support registered.
[ 14.406760] USB Serial support registered for GSM modem (1-port)
[ 14.413008] usbcore: registered new interface driver option
[ 14.418621] option: v0.7.2:USB Driver for GSM modems
[ 14.441258] fuse init (API version 7.16)
[ 15.582806] device eth0 entered promiscuous mode
[ 16.509390] UBIFS error (pid 1883): ubifs_read_node: bad node type (255 but expected 1)
[ 16.517443] UBIFS error (pid 1883): ubifs_read_node: bad node at LEB 54:33448, LEB mapping status 0
[ 16.526574] UBIFS error (pid 1883): do_readpage: cannot read page 18 of inode 1404, error -22
[ 16.535172] UBIFS error (pid 1883): ubifs_read_node: bad node type (255 but expected 1)
[ 16.543232] UBIFS error (pid 1883): ubifs_read_node: bad node at LEB 54:33448, LEB mapping status 0
[ 16.552333] UBIFS error (pid 1883): do_readpage: cannot read page 18 of inode 1404, error -22
[ 16.694874] UBIFS error (pid 1909): ubifs_read_node: bad node type (255 but expected 1)
[ 16.702971] UBIFS error (pid 1909): ubifs_read_node: bad node at LEB 54:33448, LEB mapping status 0
[ 16.712170] UBIFS error (pid 1909): do_readpage: cannot read page 18 of inode 1404, error -22
[ 16.740223] UBIFS error (pid 1912): ubifs_read_node: bad node type (255 but expected 1)
[ 16.748309] UBIFS error (pid 1912): ubifs_read_node: bad node at LEB 54:33448, LEB mapping status 0
[ 16.757400] UBIFS error (pid 1912): do_readpage: cannot read page 18 of inode 1404, error -22
[ 17.796402] UBIFS error (pid 1977): ubifs_read_node: bad node type (255 but expected 1)
[ 17.804498] UBIFS error (pid 1977): ubifs_read_node: bad node at LEB 54:33448, LEB mapping status 0
[ 17.813698] UBIFS error (pid 1977): do_readpage: cannot read page 18 of inode 1404, error -22
[ 17.826517] UBIFS error (pid 1979): ubifs_read_node: bad node type (255 but expected 1)
[ 17.834607] UBIFS error (pid 1979): ubifs_read_node: bad node at LEB 54:33448, LEB mapping status 0
[ 17.843718] UBIFS error (pid 1979): do_readpage: cannot read page 18 of inode 1404, error -22
[ 17.866304] UBIFS error (pid 1981): ubifs_read_node: bad node type (255 but expected 1)
[ 17.874401] UBIFS error (pid 1981): ubifs_read_node: bad node at LEB 54:33448, LEB mapping status 0
[ 17.883509] UBIFS error (pid 1981): do_readpage: cannot read page 18 of inode 1404, error -22
[ 17.919028] UBIFS error (pid 1986): ubifs_read_node: bad node type (255 but expected 1)
[ 17.927075] UBIFS error (pid 1986): ubifs_read_node: bad node at LEB 54:33448, LEB mapping status 0
[ 17.936207] UBIFS error (pid 1986): do_readpage: cannot read page 18 of inode 1404, error -22
[ 18.659073] device wlan0 entered promiscuous mode
[ 18.664467] br-lan: port 2(wlan0) entering listening state
[ 18.670013] br-lan: port 2(wlan0) entering listening state
[ 18.676607] cfg80211: Calling CRDA for country: PL
[ 21.130271] UBIFS error (pid 2221): ubifs_read_node: bad node type (255 but expected 1)
[ 21.138358] UBIFS error (pid 2221): ubifs_read_node: bad node at LEB 54:33448, LEB mapping status 0
[ 21.147450] UBIFS error (pid 2221): do_readpage: cannot read page 18 of inode 1404, error -22
[ 21.838048] cfg80211: Calling CRDA to update world regulatory domain
[ 29.446410] UBIFS error (pid 2928): ubifs_read_node: bad node type (255 but expected 1)
[ 29.454504] UBIFS error (pid 2928): ubifs_read_node: bad node at LEB 54:116376, LEB mapping status 0
[ 29.463699] UBIFS error (pid 2928): do_readpage: cannot read page 0 of inode 1412, error -22
[ 33.717949] br-lan: port 2(wlan0) entering learning state
[ 48.757970] br-lan: topology change detected, propagating
[ 48.763415] br-lan: port 2(wlan0) entering forwarding state
[ 73.922747] cfg80211: World regulatory domain updated:
[ 73.927926] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 73.936188] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 73.943982] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 73.951775] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 73.959561] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 73.967339] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)"

Czyli działa .
Chciałbym używać iconnecta jako NAS i do torentów.
Poprzednio służył jako router.
Czy procedura powrotu do fabrycznego firmware jest teraz inna?

Jeżeli nie zmieniałeś bootloadera to powrót do fabrycznego jest nadal taki sam jak tam gdzieś kiedyś opisywałem.

Próbowałem wedle tego poradnika

viewtopic.php?f=39&t=1219

Pytanie jest kiedy odpuścić przycisk reset?

Jak dioda będzie czerwona...

Powtórzyłem reset do oprogramowania fabrycznego dwa razy.
Dioda miga na niebiesko

komunikat o restarcie o co chodzi?

Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
Marvell>>
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25

Mapower version: iConnect 2.1 (512MB) (2010/02/02)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x200000
2097152 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.30.9
Created: 2010-01-25 19:00:21 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1990916 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................................................. done, booting the kernel.
Linux version 2.6.30.9 (soho@bsoho084.lss.emc.com) (gcc version 4.3.2 (crosstool-NG-1.3.1) ) #1 PREEMPT Mon Jan 25 13:57:26 EST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell RD-88F6281 Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 panic=30 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw
NR_IRQS:114
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 254848KB available (3632K code, 901K data, 124K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 992.87 BogoMIPS (lpj=4964352)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
PCI: bus0: Fast back to back transfers disabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 498
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:d0:b8:12:02:5a
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 2372 at 0x000012880000
Bad eraseblock 3533 at 0x00001b9a0000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000300000 : "uImage"
0x000000300000-0x000020000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd2 to ubi0
UBI: MTD device name: "root"
UBI: MTD device size: 509 MiB
UBI: number of good PEBs: 4070
UBI: number of bad PEBs: 2
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 71
UBI: total number of reserved PEBs: 3999
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 5/1
UBI: background thread "ubi_bgt0d" started, PID 394
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
input: gpio-keys as /class/input/input0
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
Registered led device: led_level
Registered led device: power_blue_led
Registered led device: power_red_led
Registered led device: usb_1_led
Registered led device: usb_2_led
Registered led device: usb_3_led
Registered led device: usb_4_led
Registered led device: otb_led
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2014-06-16 22:14:05 UTC (1402956845)
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi0:rootfs", error -19
VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00 1024 mtdblock0 (driver?)
1f01 2048 mtdblock1 (driver?)
1f02 521216 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c002c834>] (unwind_backtrace+0x0/0xdc) from [<c02e493c>] (panic+0x48/0x12c)
[<c02e493c>] (panic+0x48/0x12c) from [<c0009050>] (mount_block_root+0x25c/0x2b4)
[<c0009050>] (mount_block_root+0x25c/0x2b4) from [<c00091a0>] (prepare_namespace+0x8c/0x1c8)
[<c00091a0>] (prepare_namespace+0x8c/0x1c8) from [<c00085ac>] (kernel_init+0xbc/0xec)
[<c00085ac>] (kernel_init+0xbc/0xec) from [<c003b730>] (do_exit+0x0/0x6e0)
[<c003b730>] (do_exit+0x0/0x6e0) from [<cf81a300>] (0xcf81a300)
Rebooting in 30 seconds..
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25

Mapower version: iConnect 2.1 (512MB) (2010/02/02)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 333Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
!!!Mapower: Enter another working environment!!!
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
Marvell>>

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25

Mapower version: iConnect 2.1 (512MB) (2010/02/02)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x200000
2097152 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.30.9
Created: 2010-01-25 19:00:21 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1990916 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................................................. done, booting the kernel.
Linux version 2.6.30.9 (soho@bsoho084.lss.emc.com) (gcc version 4.3.2 (crosstool-NG-1.3.1) ) #1 PREEMPT Mon Jan 25 13:57:26 EST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell RD-88F6281 Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 panic=30 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw
NR_IRQS:114
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 254848KB available (3632K code, 901K data, 124K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 992.87 BogoMIPS (lpj=4964352)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
PCI: bus0: Fast back to back transfers disabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 498
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:d0:b8:12:02:5a
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 2372 at 0x000012880000
Bad eraseblock 3533 at 0x00001b9a0000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000300000 : "uImage"
0x000000300000-0x000020000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd2 to ubi0
UBI: MTD device name: "root"
UBI: MTD device size: 509 MiB
UBI: number of good PEBs: 4070
UBI: number of bad PEBs: 2
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 71
UBI: total number of reserved PEBs: 3999
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 5/1
UBI: background thread "ubi_bgt0d" started, PID 394
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
input: gpio-keys as /class/input/input0
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
Registered led device: led_level
Registered led device: power_blue_led
Registered led device: power_red_led
Registered led device: usb_1_led
Registered led device: usb_2_led
Registered led device: usb_3_led
Registered led device: usb_4_led
Registered led device: otb_led
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2014-06-16 22:23:10 UTC (1402957390)
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi0:rootfs", error -19
VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00 1024 mtdblock0 (driver?)
1f01 2048 mtdblock1 (driver?)
1f02 521216 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c002c834>] (unwind_backtrace+0x0/0xdc) from [<c02e493c>] (panic+0x48/0x12c)
[<c02e493c>] (panic+0x48/0x12c) from [<c0009050>] (mount_block_root+0x25c/0x2b4)
[<c0009050>] (mount_block_root+0x25c/0x2b4) from [<c00091a0>] (prepare_namespace+0x8c/0x1c8)
[<c00091a0>] (prepare_namespace+0x8c/0x1c8) from [<c00085ac>] (kernel_init+0xbc/0xec)
[<c00085ac>] (kernel_init+0xbc/0xec) from [<c003b730>] (do_exit+0x0/0x6e0)
[<c003b730>] (do_exit+0x0/0x6e0) from [<cf81a300>] (0xcf81a300)
Rebooting in 30 seconds..
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25

Mapower version: iConnect 2.1 (512MB) (2010/02/02)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 500Mhz
SysClock = 333Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
!!!Mapower: Enter another working environment!!!
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
1 Storage Device(s) found
reading uImage_nasplug_2.6.30.9_ramdisk
...
...
......................................................................................................................................................................................................................
..

2217300 bytes read
reading uboot.ramfs.gz
...
.........................................................................................................................................................................................................................................................................................................

3055699 bytes read
## Booting image at 02000000 ...
Image Name: Linux-2.6.30.9
Created: 2010-02-05 13:33:31 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2217236 Bytes = 2.1 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02300000 ...
Image Name: myram.gz
Created: 2010-04-23 3:38:51 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 3055635 Bytes = 2.9 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux................................................................................................................................................... done, booting the kernel.
Linux version 2.6.30.9 (root@flash) (gcc version 4.2.1) #8 PREEMPT Fri Feb 5 21:33:18 CST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell RD-88F6281 Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 ramdisk=32768 mtdparts=orion_nand:0xc0000@0x0(uboot),0x20000@0xa0000(env),0x300000@0x100000(zImage),0x300000@0x540000(initrd),0x1f400000@0x980000(boot)
NR_IRQS:114
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 251264KB available (4064K code, 922K data, 128K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 992.87 BogoMIPS (lpj=4964352)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
PCI: bus0: Fast back to back transfers disabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 2984K
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 497
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:d0:b8:12:02:5a
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 2372 at 0x000012880000
Bad eraseblock 3533 at 0x00001b9a0000
5 cmdlinepart partitions found on MTD device orion_nand
Creating 5 MTD partitions on "orion_nand":
0x000000000000-0x0000000c0000 : "uboot"
0x0000000a0000-0x0000000c0000 : "env"
0x000000100000-0x000000400000 : "zImage"
0x000000540000-0x000000840000 : "initrd"
0x000000980000-0x00001fd80000 : "boot"
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
mice: PS/2 mouse device common for all mice
input: gpio-keys as /devices/platform/gpio-keys/input/input0
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
Registered led device: led_level
Registered led device: power_blue_led
Registered led device: power_red_led
Registered led device: usb_1_led
Registered led device: usb_2_led
Registered led device: usb_3_led
Registered led device: usb_4_led
Registered led device: otb_led
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2014-06-16 22:23:54 UTC (1402957434)
RAMDISK: gzip image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem) on device 1:0.
usb 1-1: new high speed USB device using orion-ehci and address 2
init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
starting pid 463, tty '': '/etc/init.d/rcS'
mount: mounting /dev/sda1 on /mnt failed: No such device or address
mount: mounting /dev/sda1 on /mnt failed: No such device or address
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
mount: mounting /dev/sda1 on /mnt failed: No such device or address
usb 1-1.1: new high speed USB device using orion-ehci and address 3
usb 1-1.1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
mount: mounting /dev/sda1 on /mnt failed: No such device or address
mount: mounting /dev/sda1 on /mnt failed: No such device or address
mount: mounting /dev/sda1 on /mnt failed: No such device or address
mount: mounting /dev/sda1 on /mnt failed: No such device or address
mount: mounting /dev/sda1 on /mnt failed: No such device or address
scsi 0:0:0:0: Direct-Access CBM Flash Disk 5.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 4072448 512-byte hardware sectors: (2.08 GB/1.94 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
UBI: attaching mtd4 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: empty MTD device detected
UBI: create volume table (copy #1)
UBI: create volume table (copy #2)
UBI: attached mtd4 to ubi0
UBI: MTD device name: "boot"
UBI: MTD device size: 500 MiB
UBI: number of good PEBs: 3998
UBI: number of bad PEBs: 2
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 3955
UBI: total number of reserved PEBs: 43
UBI: number of PEBs reserved for bad PEB handling: 39
UBI: max/mean erase counter: 0/0
UBI: background thread "ubi_bgt0d" started, PID 705
UBI device number 0, total 3998 LEBs (515837952 bytes, 491.9 MiB), available 3955 LEBs (510289920 bytes, 486.7 MiB), LEB size 129024 bytes (126.0 KiB)
Set volume size to 510289920
Volume ID 0, size 3955 LEBs (510289920 bytes, 486.7 MiB), LEB size 129024 bytes (126.0 KiB), dynamic, name "boot", alignment 1
UBIFS: default file-system created
UBIFS: mounted UBI device 0, volume 0, name "boot"
UBIFS: file system size: 508354560 bytes (496440 KiB, 484 MiB, 3940 LEBs)
UBIFS: journal size: 25417728 bytes (24822 KiB, 24 MiB, 197 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 4952683 bytes (4836 KiB)
UBIFS: un-mount UBI device 0, volume 0
!!!!!!!!!!!!!!!!!!!
/tmp/nandwrite1.log
!!!!!!!!!!!!!!!!!!!


!!!!!!!!!!!!!!!!!!!
/tmp/nandwrite2.log
!!!!!!!!!!!!!!!!!!!

Writing data to block 0
Writing data to block 20000
Writing data to block 40000
Writing data to block 60000
Writing data to block 80000
Writing data to block a0000
Writing data to block c0000
Writing data to block e0000
Writing data to block 100000
Writing data to block 120000
Writing data to block 140000
Writing data to block 160000
Writing data to block 180000
Writing data to block 1a0000
Writing data to block 1c0000
Writing data to block 1e0000

!!!!!!!!!!!!!!!!!!!
/tmp/nandwrite3.log
!!!!!!!!!!!!!!!!!!!

Writing data to block 0
Writing data to block 20000
Writing data to block 40000
Writing data to block 60000
Writing data to block 80000
Writing data to block a0000
Writing data to block c0000
Writing data to block e0000
Writing data to block 100000
Writing data to block 120000
Writing data to block 140000
Writing data to block 160000
Writing data to block 180000
Writing data to block 1a0000
starting pid 720, tty '': '/bin/sh'
-sh-3.2# reboot
The system is going down NOW!
Sending SIGTERM to all processes
Requesting system reboot
Restarting system.

__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25

Mapower version: iConnect 2.1 (512MB) (2010/02/02)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x200000
2097152 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.30.9
Created: 2010-01-25 19:00:21 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1990916 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................................................. done, booting the kernel.
Linux version 2.6.30.9 (soho@bsoho084.lss.emc.com) (gcc version 4.3.2 (crosstool-NG-1.3.1) ) #1 PREEMPT Mon Jan 25 13:57:26 EST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell RD-88F6281 Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 panic=30 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw
NR_IRQS:114
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 254848KB available (3632K code, 901K data, 124K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 992.87 BogoMIPS (lpj=4964352)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
PCI: bus0: Fast back to back transfers disabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 498
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:d0:b8:12:02:5a
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 2372 at 0x000012880000
Bad eraseblock 3533 at 0x00001b9a0000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000300000 : "uImage"
0x000000300000-0x000020000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd2 to ubi0
UBI: MTD device name: "root"
UBI: MTD device size: 509 MiB
UBI: number of good PEBs: 4070
UBI: number of bad PEBs: 2
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 71
UBI: total number of reserved PEBs: 3999
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 5/1
UBI: background thread "ubi_bgt0d" started, PID 394
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
input: gpio-keys as /class/input/input0
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
Registered led device: led_level
Registered led device: power_blue_led
Registered led device: power_red_led
Registered led device: usb_1_led
Registered led device: usb_2_led
Registered led device: usb_3_led
Registered led device: usb_4_led
Registered led device: otb_led
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2014-06-16 22:26:01 UTC (1402957561)
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi0:rootfs", error -19
VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00 1024 mtdblock0 (driver?)
1f01 2048 mtdblock1 (driver?)
1f02 521216 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c002c834>] (unwind_backtrace+0x0/0xdc) from [<c02e493c>] (panic+0x48/0x12c)
[<c02e493c>] (panic+0x48/0x12c) from [<c0009050>] (mount_block_root+0x25c/0x2b4)
[<c0009050>] (mount_block_root+0x25c/0x2b4) from [<c00091a0>] (prepare_namespace+0x8c/0x1c8)
[<c00091a0>] (prepare_namespace+0x8c/0x1c8) from [<c00085ac>] (kernel_init+0xbc/0xec)
[<c00085ac>] (kernel_init+0xbc/0xec) from [<c003b730>] (do_exit+0x0/0x6e0)
[<c003b730>] (do_exit+0x0/0x6e0) from [<cf81a300>] (0xcf81a300)
Rebooting in 30 seconds..
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: RD-88F6281A LE

U-Boot 1.1.4 (Feb 2 2010 - 10:13:16) Marvell version: 3.4.25

Mapower version: iConnect 2.1 (512MB) (2010/02/02)

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1000Mhz L2 running @ 333Mhz
SysClock = 333Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII
Module 1 is TDM

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x100000, size 0x200000
2097152 bytes read: OK
## Booting image at 02000000 ...
Image Name: Linux-2.6.30.9
Created: 2010-01-25 19:00:21 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1990916 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................................................. done, booting the kernel.
Linux version 2.6.30.9 (soho@bsoho084.lss.emc.com) (gcc version 4.3.2 (crosstool-NG-1.3.1) ) #1 PREEMPT Mon Jan 25 13:57:26 EST 2010
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Marvell RD-88F6281 Reference Board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 panic=30 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw
NR_IRQS:114
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 254848KB available (3632K code, 901K data, 124K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 992.87 BogoMIPS (lpj=4964352)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
PCI: bus0: Fast back to back transfers disabled
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
msgmni has been set to 498
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:d0:b8:12:02:5a
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 2372 at 0x000012880000
Bad eraseblock 3533 at 0x00001b9a0000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000300000 : "uImage"
0x000000300000-0x000020000000 : "root"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd2 to ubi0
UBI: MTD device name: "root"
UBI: MTD device size: 509 MiB
UBI: number of good PEBs: 4070
UBI: number of bad PEBs: 2
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 71
UBI: total number of reserved PEBs: 3999
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 5/1
UBI: background thread "ubi_bgt0d" started, PID 394
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
mice: PS/2 mouse device common for all mice
input: gpio-keys as /class/input/input0
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
Registered led device: led_level
Registered led device: power_blue_led
Registered led device: power_red_led
Registered led device: usb_1_led
Registered led device: usb_2_led
Registered led device: usb_3_led
Registered led device: usb_4_led
Registered led device: otb_led
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
oprofile: using timer interrupt.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
rtc-mv rtc-mv: setting system clock to 2014-06-16 22:26:50 UTC (1402957610)
UBIFS error (pid 1): ubifs_get_sb: cannot open "ubi0:rootfs", error -19
VFS: Cannot open root device "ubi0:rootfs" or unknown-block(0,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00 1024 mtdblock0 (driver?)
1f01 2048 mtdblock1 (driver?)
1f02 521216 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[<c002c834>] (unwind_backtrace+0x0/0xdc) from [<c02e493c>] (panic+0x48/0x12c)
[<c02e493c>] (panic+0x48/0x12c) from [<c0009050>] (mount_block_root+0x25c/0x2b4)
[<c0009050>] (mount_block_root+0x25c/0x2b4) from [<c00091a0>] (prepare_namespace+0x8c/0x1c8)
[<c00091a0>] (prepare_namespace+0x8c/0x1c8) from [<c00085ac>] (kernel_init+0xbc/0xec)
[<c00085ac>] (kernel_init+0xbc/0xec) from [<c003b730>] (do_exit+0x0/0x6e0)
[<c003b730>] (do_exit+0x0/0x6e0) from [<cf81a300>] (0xcf81a300)
Rebooting in 30 seconds..

Chyba zmienne środowiskowe uboota musisz przywrócić standardowe bo nie może flasha zamontować (jest partycja o nazwie root a nie rootfs)

A jak tego dokonać?

Chyba popsułem
napisałem polecenie resetenv potem reset i mam komunikat

## Loading Ramdisk Image at 04500000 ...
Bad Magic Number

A to z kolei z braku zmiennej lub złego ustawienia arcNumber

Jakie polecenie napisać?

setenv arcNumber XXXX
saveenv

Za XXXX musisz podstawić liczbę, jaką - nie pamiętam, poszukaj jaka była w oryginalnym sofcie.

PS - tu masz jak wyglądają oryginalne zmienne: viewtopic.php?f=39&t=1219

Dla potomnych arcNumber 1682

ale komunikat dalej
## Loading Ramdisk Image at 04500000 ...
Bad Magic Number