Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
usbstart=usb start
run_diag=yes
CASset=min
MALLOC_len=1
bootargs_end=:::orion:eth0:none
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
eth1addr=00:50:43:5a:1a:2d
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
netretry=no
rcvrip=169.254.100.100
autoload=no
iomega=123
nandEcc=1bit
ethprime=egiga0
ethact=egiga0
arcNumber=1682
uboot_start=0x0
uboot_size=0xc0000
env_start=0xa0000
env_size=0x20000
kernel_start=0x100000
kernel_size=0x300000
initrd_start=0x540000
initrd_size=0x300000
flash_load=run make_boot_args load1 load2 boot
load1=nand read.e 0x2000000 $(kernel_start) $(kernel_size)
load2=nand read.e 0x4500000 $(initrd_start) $(initrd_size)
boot=bootm 0x2000000 0x4500000
krn=run a b c
rd=run d e f
a=tftp 0x2000000 zImage
b=nand erase $(kernel_start) $(kernel_size)
c=nand write.e 0x2000000 $(kernel_start) $(kernel_size)
d=tftp 0x4500000 initrd
e=nand erase $(initrd_start) $(initrd_size)
f=nand write.e 0x4500000 $(initrd_start) $(initrd_size)
flashall=run krn rd
ethaddr=00:D0:B8:11:E0:E1
make_bootsetenv=make_boot_args setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:;setenv bootargs $(bootargs)$(uboot_size)@$(uboot_start)(uboot),;setenv bootargs $(bootargs)$(env_size)@$(env_start)(env),;setenv bootargs $(bootargs)$(kernel_size)@$(kernel_start)(zImage),;setenv bootargs $(bootargs)$(initrd_size)@$(initrd_start)(initrd),;setenv bootargs
bootargs=setenv bootargs console=ttyS0,115200
boot_starsetenv=boot_start 0x980000
boot_sizesetenv=boot_size 0x1f400000
MAPOWERENV=Ver. 1.1.27 English
make_boot_args=setenv bootargs console=ttyS0,115200 mtdparts=orion_nand:;setenv bootargs $(bootargs)$(uboot_size)@$(uboot_start)(uboot),;setenv bootargs $(bootargs)$(env_size)@$(env_start)(env),;setenv bootargs $(bootargs)$(kernel_size)@$(kernel_start)(zImage),;setenv bootargs $(bootargs)$(initrd_size)@$(initrd_start)(initrd),;setenv bootargs $(bootargs)$(boot_size)@$(boot_start)(boot)
boot_start=0x980000
boot_size=0x1f400000
ipaddr=192.168.1.1
serverip=192.168.1.166
loadaddr=0x2000000
console=console=ttyS0,115200 panic=30
bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw
image_name=openwrt-kirkwood-uImage
root_name=openwrt-kirkwood-Iconnect-squashfs.uimg
update_image=tftpboot $(loadaddr) $(image_name); nand erase 0x100000 0x200000; nand write $(loadaddr) 0x100000 0x200000
load_firmware=tftpboot $(loadaddr) $(root_name); setenv bootargs $(console) root=/dev/ram0 rw; bootm $(loadaddr)
bootcmd=setenv bootargs $(console) $(bootargs_root); nand read $(loadaddr) 0x100000 0x200000; bootm $(loadaddr)
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=yes
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
hddPowerCtrl=no
enaAutoRecovery=yes
pcieTune=no
Environment size: 3162/131068 bytes
Marvell>>
A to polecenia do uruchomienia ręcznego z flash i bootloag z openwrt
Marvell>> setenv bootargs 'console=ttyS0,115200 panic=30 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw'
Marvell>> nand read 0x2000000 0x100000 0x200000
NAND read: device 0 offset 0x100000, size 0x200000
2097152 bytes read: OK
Marvell>> bootm 0x2000000
## Booting image at 02000000 ...
Image Name: Linux-3.0.9
Created: 2011-11-22 22:11:58 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1009888 Bytes = 986.2 kB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.9 (cezary@eko.one.pl) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #5 Tue Nov 22 23:11:52 CET 2011
CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
CPU: VIVT data cache, VIVT instruction cache
Machine: Iomega iConnect Wireless Data Station
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyS0,115200 panic=30 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 257028k/257028k available, 5116k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xd0800000 - 0xfe800000 ( 736 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0025000 ( 116 kB)
.text : 0xc0025000 - 0xc029d000 (2528 kB)
.data : 0xc029e000 - 0xc02b66c0 ( 98 kB)
.bss : 0xc02b66e4 - 0xc02c3820 ( 53 kB)
NR_IRQS:114
sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
Calibrating delay loop... 789.70 BogoMIPS (lpj=3948544)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A0, TCLK=200000000.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
Kirkwood PCIe port 0:
link up
PCI: bus0 uses PCIe port 0
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe000ffff]
pci 0000:00:01.0: BAR 0: set to [mem 0xe0000000-0xe000ffff] (PCI address [0xe0000000-0xe000ffff])
bio: create slab <bio-0> at 0
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 502
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
brd: module loaded
ONFI flash detected
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 1453 at 0x00000b5a0000
Bad eraseblock 1455 at 0x00000b5e0000
Bad eraseblock 1457 at 0x00000b620000
Bad eraseblock 3075 at 0x000018060000
Bad eraseblock 3077 at 0x0000180a0000
Creating 3 MTD partitions on "orion_nand":
0x000000000000-0x000000100000 : "u-boot"
0x000000100000-0x000000300000 : "uImage"
0x000000300000-0x000020000000 : "rootfs"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: max. sequence number: 64
UBI: attached mtd2 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 509 MiB
UBI: number of good PEBs: 4067
UBI: number of bad PEBs: 5
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4067
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 20/10
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 673
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:b8:11:e0:e1
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
cpuidle: using governor ladder
TCP westwood registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8
rtc-mv rtc-mv: setting system clock to 2011-11-23 15:23:33 UTC (1322061813)
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 517128192 bytes (505008 KiB, 493 MiB, 4008 LEBs)
UBIFS: journal size: 25933824 bytes (25326 KiB, 24 MiB, 201 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 4952683 bytes (4836 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:11.
Freeing init memory: 116K
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -
Please press Enter to activate this console. Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
Backport based on wireless-testing.git master-2011-11-15
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Button Hotplug driver version 0.4.1
ip_tables: (C) 2000-2006 Netfilter Core Team
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
nf_conntrack version 0.5.0 (4017 buckets, 16068 max)
i2c /dev entries driver
input: gpio-keys as /devices/platform/gpio-keys/input/input0
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
fuse init (API version 7.16)
usb 1-1: new high speed USB device number 2 using orion-ehci
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
br-lan: mixed no checksumming and other settings.
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
br-lan: mixed no checksumming and other settings.
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
br-lan: mixed no checksumming and other settings.
BusyBox v1.19.3 (2011-11-19 09:25:24 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
ATTITUDE ADJUSTMENT (bleeding edge, r29292) ----------
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
-----------------------------------------------------
Teraz jest: 2011-11-23 16:24
Temperatura CPU: 26 st. C
Temperatura NIC: 26 st. C
-----------( by obsy, http://eko.one.pl )-----------
root@OpenWrt:/$