Linux version 2.6.32.14 (xury@fedora.domowa) (gcc version 4.3.3 (GCC) ) #2 Fri May 28 22:52:05 CEST 2010
bootconsole [early0] enabled
CPU revision is: 0001800b (MIPS 4Kc)
SoC      : ADM5120P rev 8, running at 175.000 MHz
Bootdev  : NOR flash
Prom     : Generic
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 802a9fc0, node_mem_map 802e9000
  Normal zone: 32 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
Kernel command line: console=ttyS0,115200 root=/dev/sda1 init=/etc/preinit ro rootdelay=10
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13260k/16384k available (2295k kernel code, 3124k reserved, 430k data, 144k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:24
Calibrating delay loop... 173.05 BogoMIPS (lpj=346112)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is Edimax BR-6104KP
PCI: not available on ADM5120P
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  �© 2001-2006 Red Hat, Inc.
yaffs May 28 2010 22:37:56 Installing. 
msgmni has been set to 25
io scheduler noop registered
io scheduler deadline registered (default)
Serial: AMBA driver
apb:uart0: ttyS0 at MMIO 0x12600000 (irq = 9) is a AMBA
console [ttyS0] enabled, bootconsole disabled
apb:uart1: ttyS1 at MMIO 0x12800000 (irq = 10) is a AMBA
adm5120-flash.0: probing at 0x1FC00000, size:2048KiB, width:16 bits
adm5120-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
adm5120-flash.0: found at 0x1FC00000, size:2048KiB, width:16 bits
adm5120-flash.0: adding static partitions
Creating 3 MTD partitions on "adm5120-flash.0":
0x000000000000-0x000000008000 : "admboot"
0x000000008000-0x000000010000 : "config"
0x000000010000-0x000000200000 : "firmware"
ADM5120 built-in ethernet switch driver version 0.1.1
admhc-hcd: ADMtek USB 1.1 Host Controller Driver version 0.27.0
admhc-hcd: block sizes: ed 64 td 64
adm5120-hcd adm5120-hcd: ADM5120 built-in USB 1.1 Host Controller
adm5120-hcd adm5120-hcd: new USB bus registered, assigned bus number 1
adm5120-hcd adm5120-hcd: irq 11, io mem 0x11200000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
adm5120_wdt: Watchdog Timer version 0.1
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Waiting 10sec before mounting root device...
usb 1-1: new full speed USB device using adm5120-hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 1-2: new full speed USB device using adm5120-hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
scsi 0:0:0:0: Direct-Access     OTi      Flash Disk       2.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 256000 512-byte logical blocks: (131 MB/125 MiB)
usb-storage: device scan complete
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
Freeing unused kernel memory: 144k freed
Please be patient, while OpenWrt loads ...
Registered led device: power
Registered led device: usb1
Registered led device: usb2
Registered led device: wan_speed
Registered led device: wan_lnkact
Registered led device: lan1_speed
Registered led device: lan1_lnkact
Registered led device: lan2_speed
Registered led device: lan2_lnkact
Registered led device: lan3_speed
Registered led device: lan3_lnkact
Registered led device: lan4_speed
Registered led device: lan4_lnkact
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering forwarding state
Compat-wireless backport release: compat-wireless-20100517-18-gd05dc6f
Backport based on wireless-2.6.git v2.6.34-51706-gdbc5893
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
phy0: Selected rate control algorithm 'minstrel'
Registered led device: rt73usb-phy0::radio
Registered led device: rt73usb-phy0::assoc
Registered led device: rt73usb-phy0::quality
usbcore: registered new interface driver rt73usb
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (209 buckets, 836 max)
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
br-lan: port 2(wlan0) entering disabled state
br-lan: port 1(eth0) entering disabled state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device eth0 left promiscuous mode
br-lan: port 1(eth0) entering disabled state
device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering forwarding state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state