Odp: Nexx WT3020 8MB - potrzebny bootloader
Cezary napisał/a:
PS. opcja 9 to ładowanie bootloadera.
wiem, ale pisałeś żeby wgrać go przez 4.
Inna sprawa, że też nie działa. Wyrzuca błąd "raspi_wait_ready: read_sr fail: e0" do wczoraj był fr zamiast e0, ale nie wiem czy to coś zmienia. Widziałem, że inni przy starcie mają zamiast tego "raspi_wait_ready" drugi raz "raspi_read: from:30000 len:1000".
You choosed 9
0
raspi_read: from:40028 len:6
raspi_wait_ready: read_sr fail: e0
9: System Load Boot Loader then write to Flash via TFTP.
Warning!! Erase Boot Loader in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (10.10.10.123) ==:10.10.10.123
Input server IP (10.10.10.3) ==:10.10.10.3
Input Uboot filename () ==:test.bin
netboot_common, argc= 3
NetTxPacket = 0x83FE4C80
KSEG1ADDR(NetTxPacket) = 0xA3FE4C80
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server 10.10.10.3; our IP address is 10.10.10.123
Filename 'test.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (00:00:00:00:00:89)
Got it
#######################################
done
Bytes transferred = 196608 (30000 hex)
NetBootFileXferSize= 00030000
raspi_erase_write: offs:0, count:30000
raspi_erase: offs:0 len:30000
raspi_wait_ready: read_sr fail: e0
U-Boot 1.1.3 (Jan 3 2014 - 09:12:42)
MAX Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
******************************
Software System Reset Occurred
******************************
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
raspi_read: from:30000 len:1000
raspi_wait_ready: read_sr fail: e0
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jan 3 2014 Time:09:12:42
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
raspi_wait_ready: read_sr fail: e0
Bad Magic Number,00000000 "Help me Obi-Wan Kenobi. You’re my only hope. " 
I jak tak to może od razu kość 16MB a nie 8?
