51

Odp: Dlink DWR-921E

Tylko tyle że wgrałeś mu oryginalny soft od wdra. Openwrt mu wgraj...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

52

Odp: Dlink DWR-921E

AA ok ok. Bede próbował w takim razie

53

Odp: Dlink DWR-921E

*********************************************
*   U-Boot 1.1.4  (Nov 19 2014, 09:48:01)   *
*********************************************

DB120 (AR9344) U-Boot for TL-WDR3600/43x0

DRAM:   128 MB DDR2 32-bit
FLASH:  Unknown type (using only 8 MB)

Please, send request to add support
for your FLASH - JEDEC ID: 0xC84017

CLOCKS: 560/450/225/28 MHz (CPU/RAM/AHB/SPI)

LED on during eth initialization...

Hit any key to stop autobooting:  0

Booting image at: 0x9F020000

   Image name:   OpenWrt r7911-f65330
   Image type:   MIPS Linux Kernel Image (lzma compressed)
   Data size:    1385384 Bytes = 1.3 MB
   Load address: 0x80060000
   Entry point:  0x80060000

Uncompressing kernel image... OK!
Starting kernel...

[    0.000000] Linux version 4.9.199 (cezary@eko.one.pl) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7865-5880dd48d5) ) #0 Sun Nov 17 01:49:52 2019
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 3
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=TL-WDR4300  console=ttyS0,115200 rootfstype=squashfs noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 124940K/131072K available (3412K kernel code, 175K rwdata, 448K rodata, 308K init, 211K bss, 6132K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns
[    0.000010] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns
[    0.008714] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[    0.081675] pid_max: default: 32768 minimum: 301
[    0.086933] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094313] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.104881] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.115876] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.123886] NET: Registered protocol family 16
[    0.130330] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[    0.139682] ar724x-pci ar724x-pci: PCIe link is down
[    0.145219] registering PCI controller with io_map_base unset
[    0.407008] PCI host bridge to bus 0000:00
[    0.411587] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.419297] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.425508] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.433087] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.445184] clocksource: Switched to clocksource MIPS
[    0.451884] NET: Registered protocol family 2
[    0.457744] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.465571] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.472663] TCP: Hash tables configured (established 1024 bind 1024)
[    0.479836] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.486390] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.493611] NET: Registered protocol family 1
[    0.501259] Crashlog allocated RAM at address 0x3f00000
[    0.508486] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.522918] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.529462] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.549446] io scheduler noop registered
[    0.553824] io scheduler deadline registered (default)
[    0.560003] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.569910] console [ttyS0] disabled
[    0.593977] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[    0.603613] console [ttyS0] enabled
[    0.603613] console [ttyS0] enabled
[    0.611037] bootconsole [early0] disabled
[    0.611037] bootconsole [early0] disabled
[    0.625572] m25p80 spi0.0: found gd25q64, expected m25p80
[    0.632707] m25p80 spi0.0: gd25q64 (8192 Kbytes)
[    0.637726] 5 tp-link partitions found on MTD device spi0.0
[    0.643380] Creating 5 MTD partitions on "spi0.0":
[    0.648281] 0x000000000000-0x000000020000 : "u-boot"
[    0.655240] Reserved instruction in kernel code[#1]:
[    0.660293] CPU: 0 PID: 1 Comm: swapper Not tainted 4.9.199 #0
[    0.666210] task: 87c2c000 task.stack: 87c1a000
[    0.670798] $ 0   : 00000000 804a0000 00000000 523b05d3
[    0.676130] $ 4   : 00000000 00000003 00000001 00000000
[    0.681463] $ 8   : 00000001 001e0040 00000020 87cf7d00
[    0.686795] $12   : 00000001 001e0040 ffffff80 00000100
[    0.692128] $16   : 87d56200 87ddfb00 00000000 87c7ec18
[    0.697461] $20   : 80445330 80440000 00000005 8044533c
[    0.702794] $24   : 8042a834 523b05d3
[    0.708127] $28   : 87c1a000 87c1bca0 804d0000 804d0000
[    0.713460] Hi    : 0009a283
[    0.716383] Lo    : 1299edf4
[    0.719308] epc   : 804d0050 0x804d0050
[    0.723197] ra    : 804d0000 0x804d0000
[    0.727083] Status: 1100c403 KERNEL EXL IE
[    0.731353] Cause : 00800028 (ExcCode 0a)
[    0.735419] PrId  : 0001974c (MIPS 74Kc)
[    0.739392] Modules linked in:
[    0.742499] Process swapper (pid: 1, threadinfo=87c1a000, task=87c2c000, tls=00000000)
[    0.750525] Stack : 00000002 00000005 87d55880 00000007 00000000 00000000 80435274 00000005
[    0.759061]         00000000 80445530 87c7ec18 80405ea0 803f9218 80400000 87c1bd64 8025854c
[    0.767596]         00000000 00000005 803d9058 87d55880 803cc8ac 87ddfb00 00000005 80445530
[    0.776132]         87c7ec18 00000000 00000000 804d0000 804d0000 00000000 80453230 804a0000
[    0.784669]         804a0000 802548c4 804a0000 80435260 87d56000 87c7ec18 80435260 87d56000
[    0.793205]         ...
[    0.795695] Call Trace:[    0.798001] [<8025854c>] 0x8025854c
[    0.801545] [<80453230>] 0x80453230
[    0.805079] [<802548c4>] 0x802548c4
[    0.808618] [<80263e30>] 0x80263e30
[    0.812155] [<8023dcc8>] 0x8023dcc8
[    0.815694] [<8023e418>] 0x8023e418
[    0.819232] [<8023e55c>] 0x8023e55c
[    0.822768] [<8023c6cc>] 0x8023c6cc
[    0.826305] [<8023e4d8>] 0x8023e4d8
[    0.829843] [<8023c784>] 0x8023c784
[    0.833380] [<803a90dc>] 0x803a90dc
[    0.836918] [<8023c5d0>] 0x8023c5d0
[    0.840456] [<8023dab8>] 0x8023dab8
[    0.843993] [<801d3f10>] 0x801d3f10
[    0.847532] [<804784cc>] 0x804784cc
[    0.851068] [<8023ecc8>] 0x8023ecc8
[    0.854607] [<8047848c>] 0x8047848c
[    0.858144] [<804784cc>] 0x804784cc
[    0.861682] [<800609f4>] 0x800609f4
[    0.865220] [<80239e68>] 0x80239e68
[    0.868758] [<80097c9c>] 0x80097c9c
[    0.872294] [<800a3968>] 0x800a3968
[    0.875834] [<80453d10>] 0x80453d10
[    0.879370] [<80453230>] 0x80453230
[    0.882907] [<803afae8>] 0x803afae8
[    0.886446] [<803afaf8>] 0x803afaf8
[    0.889983] [<803afae8>] 0x803afae8
[    0.893519] [<80065f38>] 0x80065f38
[    0.897064]
[    0.898576] Code: 00000000  00000000  00000000 <65787061> 6e642033  322d6279  7465206b  c3739193  9e08af46
[    0.908529]
[    0.910077] ---[ end trace 54328c079823cf22 ]---
[    0.915951] Kernel panic - not syncing: Fatal exception
[    0.922363] Rebooting in 1 seconds..

54

Odp: Dlink DWR-921E

0.655240] Reserved instruction in kernel code[#1]:

Ciekawe, bo to by wynikało że procek spotkał jakiś kod którego nie potrafi zrobić/zinterpretować itd.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

55

Odp: Dlink DWR-921E

Cezary a powiedz. Da się tak zrobić żeby tego uboota od wdr3600 zaszczepić do flasza zamiast tamtego oryginalnego? Czy tamte posiakne logi z oryginalnego startu mówią w jakiej pozycji zaczyna ładować soft?

56

Odp: Dlink DWR-921E

Booting image at: 0x9F020000

Od 0x20000 masz we flash kernel i od tego adresu go uruchamia. Jak chcesz własny to zostawiasz pierwsze 0x20000 bajtów a dalej coś wgrywasz. W oryginalnej kości jeszcze gdzieś art pewnie miałeś.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.