Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Strony Poprzednia 1 … 39 40 41 42 43 … 50 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
sprawdzałem pare razy, zastanowiło mnie tylko ze na (289) po podlaczeniu swieci tylko dioda usb , a w 286 swieca usb tx i rx od razu , myslałem za gdzies zware robi ala nie..juz zdurniałem
mysle ze moze ktos juz tam grzebał. bo dal mi go kumpel.. i bylo widal lutowanie
To zobacz czy pady nie są odparzone po prostu.
sprawdze
Sam router wstaje? Nie pomyliłeś przypadkiem polaryzacji? Jeżeli obie diody świecą, to znaczy, że coś ściągnęło oba sygnały do masy.
wstaje ale normalnie laduje sie a za chwile mruga tylkko niebieska dioda i nic..
nie normalnie rx-tx i tx-rx na przemian
Wgrałem na ZTE MF286R Gargoyle 1.14
Chcę zrobić most bezprzewodowy.
1.przy konfiguracji nie skanuje żadnej sieci
2. co bym nie wpisał nie działa u mnie przycisk zapisz.
Czy na tym routerze można zrobić most bezprzewodowy?
Pozdrawiam
2. Uruchom w przegladarce konsolę js (w chrome to jest ctrl-shift-j, innych sobie poszukaj) i pokaz co tam wyświetla.
basic.sh:638 Uncaught SyntaxError: Invalid or unexpected token (at basic.sh:638:9)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at resetData (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:42255)
at basic.sh:1781:2
resetData @ basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
(anonymous) @ basic.sh:1781
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wpad_sae is not defined
at setBridgeVisibility (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:39174)
at HTMLInputElement.onclick (basic.sh:678:123)
setBridgeVisibility @ basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
onclick @ basic.sh:678
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setHwMode (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:83323)
at HTMLSelectElement.onchange (basic.sh:768:82)
setHwMode @ basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
onchange @ basic.sh:768
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setChannelWidth (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:72250)
at HTMLSelectElement.onchange (basic.sh:784:100)
setChannelWidth @ basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
onchange @ basic.sh:784
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setChannelWidth (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:72250)
at HTMLSelectElement.onchange (basic.sh:812:105)
setChannelWidth @ basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
onchange @ basic.sh:812
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: txPowerMax is not defined
at getMaxTxPower (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:88963)
at r (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:27721)
at proofreadText (common.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:27320)
at proofreadFields (common.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:12669)
at proofreadAll (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:29747)
at saveChanges (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:769)
at HTMLButtonElement.onclick (basic.sh:1773:82)
getMaxTxPower @ basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
r @ basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
proofreadText @ common.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
proofreadFields @ common.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
proofreadAll @ basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
saveChanges @ basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1
onclick @ basic.sh:1773
Zrestartuj router do ustawień domyślnych, zrestartuj, poczekaj cierpliwie z 5min po restarcie żeby zrobił sobie wszystko co trzeba i dopiero sprawdź skanowanie.
ok, to świeżo zainstalowana wersja, ustawiłem tylko hasło.
Zaraz napisze co i jak
Wykonałem
firsboot
reboot -f
samo zaznaczenie opcji "Most bezprzewodowy" dostaję komunikat
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wpad_sae is not defined
at setBridgeVisibility (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:39174)
at HTMLInputElement.onclick (basic.sh:678:123)
Pokaż wynik
cat /var/cached_basic_varsroot@Gargoyle:~# cat /var/cached_basic_vars
var isBcm94704 = false;
var allLanMacs = [];
allLanMacs.push("d4:72:26:37:d6:64");
allLanMacs.push("d4:72:26:37:d6:64");
allLanMacs.push("d4:72:26:39:d6:64");
allLanMacs.push("d4:72:26:39:d6:64");
var isRamips = false;
var wifiDevG=uciWirelessDevs.length > 0 ? uciWirelessDevs[0] : "";
var wifiDevA="";
var wirelessDriver="mac80211";
var mac80211Channels = [];
var mac80211ChFreqs = [];
var mac80211ChPwrs = [];
var nextCh=[];
var dualBandWireless=true;
nextCh = [];
nextChFreq = [];
nextChPwr = [];
wifiDevA="radio0";
var AwifiN = true;
var AwifiAC = true;
var AwifiAX = false;
var maxACwidth = "80" ;
var AC80P80 = false;
var maxAXwidth = "0" ;
var AX80P80 = false;
nextCh.push(36); nextChFreq[36] = "5180MHz"; nextChPwr[36] = 23;
nextCh.push(40); nextChFreq[40] = "5200MHz"; nextChPwr[40] = 23;
nextCh.push(44); nextChFreq[44] = "5220MHz"; nextChPwr[44] = 23;
nextCh.push(48); nextChFreq[48] = "5240MHz"; nextChPwr[48] = 23;
nextCh.push(52); nextChFreq[52] = "5260MHz"; nextChPwr[52] = 24;
nextCh.push(56); nextChFreq[56] = "5280MHz"; nextChPwr[56] = 24;
nextCh.push(60); nextChFreq[60] = "5300MHz"; nextChPwr[60] = 24;
nextCh.push(64); nextChFreq[64] = "5320MHz"; nextChPwr[64] = 24;
nextCh.push(100); nextChFreq[100] = "5500MHz"; nextChPwr[100] = 24;
nextCh.push(104); nextChFreq[104] = "5520MHz"; nextChPwr[104] = 24;
nextCh.push(108); nextChFreq[108] = "5540MHz"; nextChPwr[108] = 24;
nextCh.push(112); nextChFreq[112] = "5560MHz"; nextChPwr[112] = 24;
nextCh.push(116); nextChFreq[116] = "5580MHz"; nextChPwr[116] = 24;
nextCh.push(120); nextChFreq[120] = "5600MHz"; nextChPwr[120] = 24;
nextCh.push(124); nextChFreq[124] = "5620MHz"; nextChPwr[124] = 24;
nextCh.push(128); nextChFreq[128] = "5640MHz"; nextChPwr[128] = 24;
nextCh.push(132); nextChFreq[132] = "5660MHz"; nextChPwr[132] = 24;
nextCh.push(136); nextChFreq[136] = "5680MHz"; nextChPwr[136] = 24;
nextCh.push(140); nextChFreq[140] = "5700MHz"; nextChPwr[140] = 24;
nextCh.push(144); nextChFreq[144] = "5720MHz"; nextChPwr[144] = 24;
nextCh.push(149); nextChFreq[149] = "5745MHz"; nextChPwr[149] = 30;
nextCh.push(153); nextChFreq[153] = "5765MHz"; nextChPwr[153] = 30;
nextCh.push(157); nextChFreq[157] = "5785MHz"; nextChPwr[157] = 30;
nextCh.push(161); nextChFreq[161] = "5805MHz"; nextChPwr[161] = 30;
nextCh.push(165); nextChFreq[165] = "5825MHz"; nextChPwr[165] = 30;
nextCh.push(169); nextChFreq[169] = "5845MHz"; nextChPwr[169] = 27;
nextCh.push(173); nextChFreq[173] = "5865MHz"; nextChPwr[173] = 27;
mac80211Channels["A"] = nextCh ;
mac80211ChFreqs["A"] = nextChFreq ;
mac80211ChPwrs["A"] = nextChPwr ;
nextCh = [];
nextChFreq = [];
nextChPwr = [];
wifiDevG="radio1";
var GwifiN = true;
var GwifiAX = false;
nextCh.push(1); nextChFreq[1] = "2412MHz"; nextChPwr[1] = 25;
nextCh.push(2); nextChFreq[2] = "2417MHz"; nextChPwr[2] = 25;
nextCh.push(3); nextChFreq[3] = "2422MHz"; nextChPwr[3] = 25;
nextCh.push(4); nextChFreq[4] = "2427MHz"; nextChPwr[4] = 25;
nextCh.push(5); nextChFreq[5] = "2432MHz"; nextChPwr[5] = 25;
nextCh.push(6); nextChFreq[6] = "2437MHz"; nextChPwr[6] = 25;
nextCh.push(7); nextChFreq[7] = "2442MHz"; nextChPwr[7] = 25;
nextCh.push(8); nextChFreq[8] = "2447MHz"; nextChPwr[8] = 25;
nextCh.push(9); nextChFreq[9] = "2452MHz"; nextChPwr[9] = 25;
nextCh.push(10); nextChFreq[10] = "2457MHz"; nextChPwr[10] = 25;
nextCh.push(11); nextChFreq[11] = "2462MHz"; nextChPwr[11] = 25;
mac80211Channels["G"] = nextCh ;
mac80211ChFreqs["G"] = nextChFreq ;
mac80211ChPwrs["G"] = nextChPwr ;
var wpad_eap = true;
var wpad_sae = true;
var wpad_owe = true;
var wpad_sb192 = true;
var wpad_wep = false;
var distribTarget='ath79/nand';
Nie, u mnie wybranie opcji mostu działa normalnie. W sumie też wszystkie zmienne masz jakie trzeba.
próbuję na Firefox, Chrome, Microsoft Edge.
Jutro zmienię komputer lub odpalę linux-a
Wejdź w zakładkę konfiguracja/podstawowa, zrób podgląd źródła strony, skopiuj całość, wstaw na pastebin.com i daj tu linka.
Źródło strony
https://pastebin.com/ExXP2vFZ
błędy JS
basic.sh:638 Uncaught SyntaxError: Invalid or unexpected token
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at resetData (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:42255)
at basic.sh:1781:2
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: dualBandWireless is not defined
at setBridgeVisibility (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:41066)
at HTMLInputElement.onclick (basic.sh:674:125)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setGlobalVisibility (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:30627)
at HTMLSelectElement.onchange (basic.sh:973:89)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setGlobalVisibility (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:30627)
at HTMLSelectElement.onchange (basic.sh:1140:90)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setHwMode (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:83323)
at HTMLSelectElement.onchange (basic.sh:1322:80)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setChannelWidth (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:72250)
at HTMLSelectElement.onchange (basic.sh:1334:98)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: maxACwidth is not defined
at setHwMode (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:80670)
at HTMLSelectElement.onchange (basic.sh:1360:85)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setChannelWidth (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:72250)
at HTMLSelectElement.onchange (basic.sh:1373:103)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wpad_sae is not defined
at setWifiVisibility (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:34295)
at HTMLSelectElement.onchange (basic.sh:1502:124)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: txPowerMax is not defined
at getMaxTxPower (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:88963)
at r (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:27721)
at proofreadText (common.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:27320)
at proofreadFields (common.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:12669)
at proofreadAll (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:29343)
at saveChanges (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:769)
at HTMLButtonElement.onclick (basic.sh:1773:82)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setChannelWidth (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:72250)
at HTMLSelectElement.onchange (basic.sh:1334:98)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: wirelessDriver is not defined
at setChannelWidth (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:72250)
at HTMLSelectElement.onchange (basic.sh:1373:103)
basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1 Uncaught ReferenceError: txPowerMax is not defined
at getMaxTxPower (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:88963)
at r (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:27721)
at proofreadText (common.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:27320)
at proofreadFields (common.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:12669)
at proofreadAll (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:29343)
at saveChanges (basic.js?1.14.0.1--Built-20230623-1554-git-8e210b77-:1:769)
at HTMLButtonElement.onclick (basic.sh:1773:82)
cdcif = "usb0
usb1";
to jest problemem. Pokaż mi wyniki poleceń:
ls -al /sys/class/net/*/device/interface
cat /sys/class/net/*/device/interface
ls -al /sys/class/net/*/device/driverroot@Gargoyle:~# cat /sys/class/net/*/device/interface
CDC Ethernet Control Model (ECM)
RNDIS Communications Control
root@Gargoyle:~# ls -al /sys/class/net/*/device/interface
-r--r--r-- 1 root root 4096 Apr 28 04:07 /sys/class/net/usb0/device/interface
-r--r--r-- 1 root root 4096 Apr 28 04:07 /sys/class/net/usb1/device/interface
root@Gargoyle:~# cat /sys/class/net/*/device/interface
CDC Ethernet Control Model (ECM)
RNDIS Communications Control
root@Gargoyle:~# ls -al /sys/class/net/*/device/driver
lrwxrwxrwx 1 root root 0 Apr 28 04:07 /sys/class/net/eth0/device/driver -> ../../../../bus/platform/drivers/ag71xx
lrwxrwxrwx 1 root root 0 Apr 28 04:07 /sys/class/net/usb0/device/driver -> ../../../../../../../bus/usb/drivers/cdc_ether
lrwxrwxrwx 1 root root 0 Apr 28 04:07 /sys/class/net/usb1/device/driver -> ../../../../../../../bus/usb/drivers/rndis_host
lrwxrwxrwx 1 root root 0 Apr 28 04:07 /sys/class/net/wlan0/device/driver -> ../../../bus/pci/drivers/ath10k_pci
lrwxrwxrwx 1 root root 0 Apr 28 04:07 /sys/class/net/wlan1/device/driver -> ../../../../bus/platform/drivers/ath9k
root@Gargoyle:~#
Modem w MF286R wymaga specjalnego traktowania. Zaloguj się przez ssh i wykonaj to:
sed -i "s|echo \"hasNCM = false;\"|echo \"hasNCM = true;\"|" /www/basic.sh
sed -i "s|echo \"cdcif = .*|echo \"cdcif = \\\\\"\\\\\";\"|" /www/basic.shOdśwież później stronę, powinno pomóc.
Wiem, że te modemy są specjalnej troski.
Udostępniałem go jak nie można było uruchomić na nich komunikacji.
Po wprowadzeniu zmian można już bezproblemowo ustawiać most bezprzewodowy.
Dziękuję i pozdrawiam.
Po udanej instalacji OpenWrt wczoraj, powróciłem do oryginalnego firmware, aby uzyskać najnowszą wersję modemu. Ale dzisiaj dostaję błąd kernel panic podczas uruchamiania OpenWrt. Czy możesz mi pomóc?
[ 0.346780] printk: console [ttyS0] enabled
[ 0.346780] printk: console [ttyS0] enabled
[ 0.355842] printk: bootconsole [early0] disabled
[ 0.355842] printk: bootconsole [early0] disabled
[ 0.382257] spi-nand spi0.1: GigaDevice SPI NAND was found.
[ 0.388031] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[ 0.398845] 6 fixed-partitions partitions found on MTD device (null)
[ 0.405501] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[ 0.412385] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[ 0.419929] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[ 0.426832] OF: Bad cell count for /ahb/spi@1f000000/flash@1/partitions
[ 0.434406] Creating 6 MTD partitions on "(null)":
[ 0.439364] 0x000000000000-0x0000000a0000 : "fota-flag"
[ 0.448902] 0x0000000a0000-0x000000120000 : "art"
[ 0.456204] 0x000000120000-0x0000001a0000 : "mac"
[ 0.463580] 0x0000001a0000-0x000001800000 : "ubiconcat0"
[ 0.500452] 0x000001800000-0x000001c00000 : "kernel"
[ 0.512701] 0x000001c00000-0x000008000000 : "ubiconcat1"
[ 0.659362] spi-nor spi0.0: gd25q16 (2048 Kbytes)
[ 0.664321] 3 fixed-partitions partitions found on MTD device spi0.0
[ 0.670884] Creating 3 MTD partitions on "spi0.0":
[ 0.675863] 0x000000000000-0x0000000a0000 : "u-boot"
[ 0.682755] 0x0000000a0000-0x0000000c0000 : "u-boot-env"
[ 0.689170] 0x0000000c0000-0x000000200000 : "reserved1"
[ 0.698249] Concatenating MTD devices:
[ 0.702198] (0): "ubiconcat0"
[ 0.705259] (1): "ubiconcat1"
[ 0.708323] into device "ubi-concat"
[ 0.712056] 1 fixed-partitions partitions found on MTD device ubi-concat
[ 0.718971] Creating 1 MTD partitions on "ubi-concat":
[ 0.724298] 0x000000000000-0x000007a60000 : "ubi"
[ 1.425862] switch0: Atheros AR8337 rev. 2 switch registered on mdio.0
[ 2.083353] ag71xx 19000000.eth: connected to PHY at mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 2.094631] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode: sgmii
[ 2.103343] NET: Registered protocol family 10
[ 2.115439] Segment Routing with IPv6
[ 2.119347] NET: Registered protocol family 17
[ 2.124074] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 2.137468] 8021q: 802.1Q VLAN Support v1.8
[ 2.145761] PCI host bridge /ahb/pcie-controller@18250000 ranges:
[ 2.152132] MEM 0x0000000012000000..0x0000000013ffffff
[ 2.157529] IO 0x0000000000000000..0x0000000000000000
[ 2.163091] PCI host bridge to bus 0000:00
[ 2.167336] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 2.174468] pci_bus 0000:00: root bus resource [io 0x0000]
[ 2.180223] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 2.187244] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.195492] pci 0000:00:00.0: [168c:0056] type 00 class 0x028000
[ 2.201733] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 2.208884] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 2.215807] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 2.222713] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 2.235191] UBI: auto-attach mtd9
[ 2.238646] ubi0: attaching mtd9
[ 4.932686] ubi0: scanning is finished
[ 4.970553] ubi0: attached mtd9 (name "ubi", size 122 MiB)
[ 4.976279] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.983395] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.990398] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.997595] ubi0: good PEBs: 977, bad PEBs: 2, corrupted PEBs: 0
[ 5.003802] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.011259] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 799738486
[ 5.020605] ubi0: available PEBs: 0, total reserved PEBs: 977, PEBs reserved for bad PEB handling: 18
[ 5.030227] ubi0: background thread "ubi_bgt0d" started, PID 348
[ 5.039317] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.045043] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.075104] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.089334] Freeing unused kernel memory: 1244K
[ 5.094043] This architecture does not have kernel memory protection.
[ 5.100698] Run /sbin/init as init process
[ 5.904815] init: Console is alive
[ 5.908758] init: - watchdog -
[ 7.520620] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 7.659852] usbcore: registered new interface driver usbfs
[ 7.665655] usbcore: registered new interface driver hub
[ 7.671213] usbcore: registered new device driver usb
[ 7.685570] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.695317] fsl-ehci: Freescale EHCI Host controller driver
[ 7.703218] ehci-platform: EHCI generic platform driver
[ 7.708948] ehci-platform 1b000000.usb: EHCI Host Controller
[ 7.714879] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1
[ 7.723113] ehci-platform 1b000000.usb: irq 13, io mem 0x1b000000
[ 7.751882] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[ 7.759071] hub 1-0:1.0: USB hub found
[ 7.763764] hub 1-0:1.0: 1 port detected
[ 7.768573] ehci-platform 1b400000.usb: EHCI Host Controller
[ 7.774504] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2
[ 7.782758] ehci-platform 1b400000.usb: irq 14, io mem 0x1b400000
[ 7.811870] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
[ 7.819034] hub 2-0:1.0: USB hub found
[ 7.823736] hub 2-0:1.0: 1 port detected
[ 7.831111] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 7.849063] init: - preinit -
[ 8.763069] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 8.980461] random: procd: uninitialized urandom read (4 bytes read)
[ 9.249821] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.331523] random: jshn: uninitialized urandom read (4 bytes read)
[ 10.796130] eth0: link up (1000Mbps/Full duplex)
[ 10.800929] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 10.819764] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 15.166737] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 15.182496] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 494
[ 15.353800] UBIFS (ubi0:1): recovery needed
[ 15.652180] UBIFS (ubi0:1): recovery completed
[ 15.656868] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 15.664983] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 15.675231] UBIFS (ubi0:1): FS size: 115294208 bytes (109 MiB, 908 LEBs), journal size 5713920 bytes (5 MiB, 45 LEBs)
[ 15.686185] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB)
[ 15.693025] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID B5E9FD4B-B3FE-4324-84DB-5CFBB078BA91, small LPT model
[ 15.713201] mount_root: overlay filesystem has not been fully initialized yet
[ 15.726624] mount_root: switching to ubifs overlay
[ 15.752247] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 15.890362] eth0: link down
[ 15.911714] procd: - early -
[ 15.916244] procd: - watchdog -
[ 16.756693] procd: - watchdog -
[ 16.923795] procd: - ubus -
[ 17.352039] random: ubusd: uninitialized urandom read (4 bytes read)
[ 17.361179] random: ubusd: uninitialized urandom read (4 bytes read)
[ 17.385073] random: ubusd: uninitialized urandom read (4 bytes read)
[ 17.415658] procd: - init -
Please press Enter to activate this console.
[ 18.807334] random: jshn: uninitialized urandom read (4 bytes read)
[ 18.859179] random: ubusd: uninitialized urandom read (4 bytes read)
[ 18.871509] random: ubus: uninitialized urandom read (4 bytes read)
[ 19.473354] kmodloader: loading kernel modules from /etc/modules.d/*
[ 19.953646] urngd: v1.0.2 started.
[ 20.002582] cdc_acm 1-1:1.2: ttyACM0: USB ACM device
[ 20.022244] usbcore: registered new interface driver cdc_acm
[ 20.028113] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 20.072295] usbcore: registered new interface driver cdc_wdm
[ 20.096910] Loading modules backported from Linux version v5.15.92-0-ge515b9902f5f
[ 20.104782] Backport generated by backports.git v5.15.92-1-0-gdfe0f60c
[ 20.202559] usbcore: registered new interface driver usbserial_generic
[ 20.209374] usbserial: USB Serial support registered for generic
[ 20.253645] cdc_ether 1-1:1.6 usb0: register 'cdc_ether' at usb-1b000000.usb-1, ZTE CDC Ethernet Device, 1a:5a:00:9d:40:d8
[ 20.265311] usbcore: registered new interface driver cdc_ether
[ 20.294690] usbcore: registered new interface driver cdc_ncm
[ 20.351918] random: crng init done
[ 20.355447] random: 28 urandom warning(s) missed due to ratelimiting
[ 20.443393] usbcore: registered new interface driver huawei_cdc_ncm
[ 20.604007] PPP generic driver version 2.4.2
[ 20.623124] NET: Registered protocol family 24
[ 20.653211] rndis_host 1-1:1.0 usb1: register 'rndis_host' at usb-1b000000.usb-1, ZTE RNDIS device, be:63:4e:94:fd:85
[ 20.664450] usbcore: registered new interface driver rndis_host
[ 20.792576] ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x56.
[ 20.802010] ath10k_pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 20.808772] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 23.503492] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[ 23.513060] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 23.532240] ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
[ 23.873911] ath10k_pci 0000:00:00.0: Loading BDF type 0
[ 23.881253] ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=31 from ath10k/QCA9888/hw2.0/board-2.bin
[ 24.318083] ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
[ 24.327843] ath10k_pci 0000:00:00.0: failed to fetch board file: -12
[ 24.352083] ath10k_pci 0000:00:00.0: could not probe fw (-12)
[ 24.410325] usbcore: registered new interface driver option
[ 24.416237] usbserial: USB Serial support registered for GSM modem (1-port)
[ 24.482049] Data bus error, epc == 8033539c, ra == 820a2cf4
[ 24.487818] Oops[#1]:
[ 24.490168] CPU: 0 PID: 742 Comm: kmodloader Not tainted 5.10.176 #0
[ 24.496720] $ 0 : 00000000 00000001 deadc0de 00014000
[ 24.502130] $ 4 : b81143fc 000143fc 82001c14 00000004
[ 24.507533] $ 8 : 00000000 8039ae7c ffffffff ffffffff
[ 24.512936] $12 : ffffffff 00000020 00000000 ffffffff
[ 24.518340] $16 : 81f2c080 00000018 81b8bb44 81b8bb48
[ 24.523742] $20 : 81b8bf43 80000003 00010000 00014000
[ 24.529145] $24 : 00000000 8045d890
[ 24.534548] $28 : 81b8a000 81b8bad0 00031018 820a2cf4
[ 24.539951] Hi : 00004b5c
[ 24.542917] Lo : 4e910000
[ 24.545886] epc : 8033539c 0x8033539c
[ 24.549857] ra : 820a2cf4 0x820a2cf4 [ath9k_hw@7cee0de1+0x54ec0]
[ 24.556321] Status: 1100dc03 KERNEL EXL IE
[ 24.560649] Cause : 4080801c (ExcCode 07)
[ 24.564780] PrId : 00019750 (MIPS 74Kc)
[ 24.568828] Modules linked in: ath9k(+) ath9k_common pppoe ppp_async option nft_fib_inet nf_flow_table_ipv6 nf_flow_table_ipv4 nf_flow_table_inet ath9k_hw ath10k_pci ath10k_core ath usb_wwan rndis_host pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_objref nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_counter nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mac80211 huawei_cdc_ncm cfg80211 cdc_ncm cdc_ether usbserial usbnet slhc nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_ipv6 nf_log_ipv4 nf_log_common nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c hwmon crc_ccitt compat cdc_wdm cdc_acm sha256_generic libsha256 seqiv jitterentropy_rng drbg hmac cmac fsl_mph_dr_of ehci_platform ehci_fsl ehci_hcd gpio_button_hotplug phy_ar7100_usb usbcore nls_base usb_common mii crc32c_generic
[ 24.651446] Process kmodloader (pid: 742, threadinfo=bf02531a, task=7955bb43, tls=77eacdf0)
[ 24.660060] Stack : 00000005 00000003 00000dc0 00000000 81b8baec 00000000 00000220 000003ff
[ 24.668696] 81e71000 00008000 81f2c080 81f2c0a8 820a0000 81b8bbb4 820d0000 820a3e14
[ 24.677334] 00000000 81f2c080 00020000 00007000 ffffffe0 81f2c5b8 81f2c0a8 820d1f50
[ 24.685972] 80c98e4c 00000000 80c02d00 00000cc0 000186a0 ffffffff 81f2c080 820d0558
[ 24.694609] 99999999 00008000 00000100 81f2c0a8 00000000 81b8bbb4 820d0000 82095348
[ 24.703247] ...
[ 24.705774] Call Trace:
[ 24.705826] [<820a0000>] 0x820a0000 [ath9k_hw@7cee0de1+0x54ec0]
[ 24.714460] [<820a3e14>] 0x820a3e14 [ath9k_hw@7cee0de1+0x54ec0]
[ 24.720601] [<82095348>] 0x82095348 [ath9k_hw@7cee0de1+0x54ec0]
[ 24.726721] [<82086cd4>] 0x82086cd4 [ath9k_hw@7cee0de1+0x54ec0]
[ 24.732844] [<80416d68>] 0x80416d68
[ 24.736461] [<800a0000>] 0x800a0000
[ 24.740070] [<82002864>] 0x82002864 [ath9k@827bab61+0x192b0]
[ 24.745911] [<82004948>] 0x82004948 [ath9k@827bab61+0x192b0]
[ 24.751749] [<800c44e4>] 0x800c44e4
[ 24.755364] [<82010090>] 0x82010090 [ath9k@827bab61+0x192b0]
[ 24.761204] [<8023f8a0>] 0x8023f8a0
[ 24.764811] [<8039fdc0>] 0x8039fdc0
[ 24.768417] [<80241f80>] 0x80241f80
[ 24.772026] [<80414d9c>] 0x80414d9c
[ 24.775629] [<804129d8>] 0x804129d8
[ 24.779237] [<80413508>] 0x80413508
[ 24.782838] [<804150d8>] 0x804150d8
[ 24.786440] [<80384bb8>] 0x80384bb8
[ 24.790036] [<80413518>] 0x80413518
[ 24.793638] [<80413594>] 0x80413594
[ 24.797247] [<80413518>] 0x80413518
[ 24.800841] [<80410564>] 0x80410564
[ 24.804458] [<80411c7c>] 0x80411c7c
[ 24.808068] [<800ebd40>] 0x800ebd40
[ 24.811667] [<80413d78>] 0x80413d78
[ 24.815270] [<8201f000>] 0x8201f000 [ath9k@827bab61+0x192b0]
[ 24.821111] [<8201f018>] 0x8201f018 [ath9k@827bab61+0x192b0]
[ 24.826952] [<80060970>] 0x80060970
[ 24.830553] [<800ea170>] 0x800ea170
[ 24.834154] [<801a4164>] 0x801a4164
[ 24.837772] [<800ea190>] 0x800ea190
[ 24.841369] [<800ec150>] 0x800ec150
[ 24.844979] [<8006e1ac>] 0x8006e1ac
[ 24.848590]
[ 24.850128] Code: 0000000f 8c820000 0000000f <03e00008> 00000000 0000000f 94820000 3042ffff 0000000f
[ 24.860208]
[ 24.861794] ---[ end trace 196c38740f66603d ]---
[ 24.866581] Kernel panic - not syncing: Fatal exception
[ 24.871979] Rebooting in 1 seconds..Jaki obraz wgrałeś? Bo nie ma firmware od radia. Ponad to sterownik się wywalił. Nie jest to czasami initramfs wgrany do flash?
Wgrałem build OpenWrt. Najpierw uruchomiłem initramfs metodą TFTP. Następnie wszedłem w tryb failsafe i wykonałem sysupgrade. Po ponownym uruchomieniu uzyskałem ten sam wynik. W końcu stworzyłem root_uImage z initramfs i próbowałem załadować go przy pomocy TFTP recovery, ale z tym samym efektem.
Przy okazji mogę z powodzeniem uruchamiać oryginalne firmware (T-Mobile).
https://openwrt.org/toh/zte/mf286r
https://downloads.openwrt.org/releases/ … kernel.bin
https://downloads.openwrt.org/releases/ … pgrade.bin
Strony Poprzednia 1 … 39 40 41 42 43 … 50 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc