Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Strony Poprzednia 1 … 30 31 32 33 34 … 50 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
Niestety porazka jako zdalnie zarzadzany modem. jakakolwiek zmiana wymaga reboota trwajacy 5 minut i oczekiwanie czy aby na pewno połaczy sie.
No to wgrywaj oryginał i tyle zabawy.
Dla potomnych revert na factory sw"
- Na jakims systemie linux skleić root_uImage z partycji z backupu
cat mtd11.bin mtd12.bin mtd13.bin > root_uImage
- podłaczyc uart do routera
- ustawić na interfejsie serwera tftp IP 192.168.0.22 255.255.255.0
- Zabootowac z TFTP jakiś obraz openwrt-initramfs.bin przez uboot i UART:
tftpboot 0x81000000 openwrt-initramfs.bin
(tftpboot 0x81000000 mifi-22.03-snapshot-r19441-3cfe050c4a-zte_mf286r-initramfs-kernel.bin)
bootm 0x81000000
po tym wstanie openwrt "life"
- ustawic na interfejsie serwera tftp 192.0.0.1 255.0.0.0
i wystawic sklejany wczesniej plik root_uImage
kleimy przez:
cat mtd11 mtd12 mtd13 > root_uImage_restore_factory
- po uarcie sprawdzić jaki numerek mtd ma obecnie "kernel" przez:
cat /proc/mtd
W przypadku MF286R z openwrt jest to mtd4
- wymazac partycje z shell przez:
mtd erase /dev/mtd4
- na konsoli wydac komendę "reboot"
- w konsoli uart zobaczysz "nand write_partition ok
blank download is done. send fin to PC...
"
- zrobić reset prądowyt routera
- wstanie fabryczny softNo i niestety na fabrycznym sofcie migiem łaczy sie , reconnect z gui działa od razu i co ciekawe zauważam że agreguje bez problemu. Na mifi miało opory z agregacją
I jak dobrze wiesz to modem robi agregację z nie mifi czy openwrt, także - nie trafiona uwaga.
Wiem, że modem to osobny byt ale jednak to fakt.
Na mifi za cholerę nie połaczyło sie 2CA a na oryginale łączy sie 100/100.
Ogolnie wszystko działa duzo szybciej.
Także coś z obrazem MiFi dla 286R jest mocno nie halo - porównując do oryginału i sposobu działania 286A i 286D
Jasne 
Jest dokładnie taki sam jak dla innych modeli, wszak to tylko gui i samo w sobie nie zawiera żadnych "udoskonaleń" systemowych.
integracja R wyszla duzo gorzej
Wgraj sobie zwykły obraz openwrt, nawet nie mój tylko z openwrt.org. I zobacz jak się zachowuje.
Szybka akcja - poszedł w świat
uff, przebrnąłem przez wątek. nie znam się od strony technicznej, ale widzę ogrom pracy i wykonany kaaaawał dobrej roboty.
gratulacje!
będę miał 286R z plusa/polsatu w przyszłym tygodniu.
będę meldował co i jak
@geos Dumpnij firmware i podrzuć mi albo Cezaremu gdy to zrobisz ;-)
Te sprzęty nie mają generycznych i oficjalnych releasów, więc musimy jakoś sobie radzić.
ok, mam go w rękach. oryginalne oprogramowanie pokazuje wersję: CR_PKTPLMF286V1.0.0B09
nie ma aktualizacji.
walczę, aby wyjąć PCB z obudowy. na razie tylna klapa się poddała. wygląda na to, że przednia mocniej trzyma.
cztery wkręty na około + czasami jedna w środku.
Cezary, te srubki już opanowałem, tylko ta przednia część jest jakby sklejona oprócz tego, że ma zaczepy. walczę.
Zatrzaski po obu stronach obudowy były IIRC identycznie umiejscowione. Ja zazwyczaj zaczynałem otwieranie od góry i po obwodzie.
Co by było dziwne. Tylko zaczepy zostały, przynajmniej wg tego co już zdążyłem rozebrać. Więc użyj trochę siły po prostu.
sukces. tak to wygląda:
trup słał się gęsto:
jednak nie były sklejone, to ten plastik od piórek zostawiał ślad na czarnej obudowie i wyglądało jak klej.
jutro ciąg dalszy!
uname -a
Linux (none) 3.3.8 #1 Thu Sep 19 17:30:40 CST 2019 mips GNU/Linuxadmin@(none):~# cat /proc/cpuinfo
system type\0x09\0x09: Qualcomm Atheros QCA956X rev 0
machine\0x09\0x09\0x09: Qualcomm Atheros AP152 reference board
processor\0x09\0x09: 0
cpu model\0x09\0x09: MIPS 74Kc V5.0
BogoMIPS\0x09\0x09: 385.84
wait instruction\0x09: yes
microsecond timers\0x09: yes
tlb_entries\0x09\0x09: 32
extra interrupt vector\0x09: yes
hardware watchpoint\0x09: yes, count: 4, address/irw mask: [0x0000, 0x0ff8, 0x0ffb, 0x0ff8]
ASEs implemented\0x09: mips16 dsp
shadow register sets\0x09: 1
kscratch registers\0x09: 0
core\0x09\0x09\0x09: 0
VCED exceptions\0x09\0x09: not available
VCEI exceptions\0x09\0x09: not availableadmin@(none):~# cat /sys/kernel/debug/usb/devices
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8 ehci_hcd
S: Product=Generic Platform EHCI Controller
S: SerialNumber=ehci-platform.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8 ehci_hcd
S: Product=Generic Platform EHCI Controller
S: SerialNumber=ehci-platform.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=1489 Rev=ff.ff
S: Manufacturer=ZTE
S: Product=ZTE
S: SerialNumber=123456789ABCD
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 2mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
A: FirstIf#= 2 IfCount= 2 Cls=02(comm.) Sub=02 Prot=01
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=1ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=01 Driver=cdc_acm
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=ff Driver=(none)
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=usbfs
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0msadmin@(none):~# cat /proc/mtd
dev: size erasesize name
mtd0: 000a0000 00010000 "u-boot"
mtd1: 00020000 00010000 "u-boot-env"
mtd2: 00140000 00010000 "reserved1"
mtd3: 000a0000 00020000 "fota-flag"
mtd4: 00080000 00020000 "art"
mtd5: 00080000 00020000 "mac"
mtd6: 000c0000 00020000 "reserved2"
mtd7: 00400000 00020000 "cfg-param"
mtd8: 00400000 00020000 "log"
mtd9: 000a0000 00020000 "oops"
mtd10: 00500000 00020000 "reserved3"
mtd11: 00800000 00020000 "web"
mtd12: 00300000 00020000 "kernel"
mtd13: 01a00000 00020000 "rootfs"
mtd14: 01900000 00020000 "data"
mtd15: 03200000 00020000 "fota"
mtd16: 01d00000 00020000 "firmware"boot log:
U-Boot 1.1.4 (Jun 25 2019 - 11:21:44)
ap152 - Dragonfly 1.0DRAM:
ath_ddr_initial_config(278): (ddr2 init)
ath_sys_frequency: cpu 775 ddr 650 ahb 258
Tap values = (0xf, 0xf, 0xf, 0xf)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 409k for U-Boot at: 87f98000
Reserving 192k for malloc() at: 87f68000
Reserving 44 Bytes for Board Info at: 87f67fd4
Reserving 36 Bytes for Global Data at: 87f67fb0
Reserving 128k for boot params() at: 87f47fb0
Stack Pointer at: 87f47f98
Now running in RAM - U-Boot at: 87f98000
Flash Manuf Id 0xc8, DeviceId0 0x40, DeviceId1 0x15
flash size 2MB, sector count = 32
Flash: 2 MB
*** Warning - bad CRC, using default environment
Power up PLL with outdiv = 0 then switch to 3
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
athr_mgmt_init (MDC/MDIO config)::done
Dragonfly ----> S17 PHY *
athrs17_reg_init: complete
Max resets limit reached exiting...
athr_gmac_sgmii_setup SGMII done
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:ff:ff:ff
ath_gmac_phy_setup
eth0 up
eth0
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc.
ath_spi_nand_ecc: furture feat = 0x10
ath_spi_nand_ecc: middle feat = 0x10
zte ath_spi_nand_read_id 0xc8d1
zte ath_spi_nand_read_id 0xc8d1c8
zte debug gd 128 oob
====== NAND Parameters ======
sc addr = 0x87ff7290 page(write size) = 0x800 (erase size) block = 0x20000
Setting 0x181162c0 to 0x4b962100
Uaztemain: enter into !
zte_getHandOffState: read data=0xff from 0x0
Uaztemain: no need to update ''
Hit any key to stop autoboot: 2
Loading from device 0: ath-spi-nand (offset 0x1800000)
Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2019-09-19 9:31:28 UTC
Image Type: MIPS Linux Multi-File Image (lzma compressed)
Data Size: 1210411 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Contents:
Image 0: 1210403 Bytes = 1.2 MB
ath_spi_nand_page_read :status=0x1
## Booting image at 81000000 ...
Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2019-09-19 9:31:28 UTC
Image Type: MIPS Linux Multi-File Image (lzma compressed)
Data Size: 1210411 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Contents:
Image 0: 1210403 Bytes = 1.2 MB
Verifying Checksum at 0x81000040 ...OK
Uncompressing Multi-File Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (scl@scl_xa243_241) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Thu Sep 19 17:30:40 CST 2019
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019750 (MIPS 74Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA956X rev 0
[ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=AP152 console=ttyS0,115200 mtdparts=spi0.0:640k(u-boot),128k(u-boot-env),1280k(reserved1);spi0.1:640k(fota-flag),512k(art),512k(mac),768k(reserved2),4m(cfg-param),4m(log),640k(oops),5m(reserved3),8m(web),3m(kernel),26m(rootfs),25m(data),50m(fota),29m@0x1800000(firmware) mem=128M rootfstype=squashfs,jffs2 noinitrd crashkernel=10M@20M oops=panic
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125784k/131072k available (2574k kernel code, 5288k reserved, 687k data, 228k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.060000] Performance counters: mips/74K PMU enabled, 4 32-bit counters available to each CPU, irq 13
[ 0.070000] NET: Registered protocol family 16
[ 0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[ 0.080000] MIPS: machine is Qualcomm Atheros AP152 reference board
[ 0.090000]
[ 0.090000] WLAN firmware dump buffer allocation of 2097152 bytes @ address 0x87a00000- SUCCESS !!!
[ 0.100000] registering PCI controller with io_map_base unset
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.310000] PCI host bridge to bus 0000:00
[ 0.320000] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [io 0x0001]
[ 0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 0.330000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.340000] Switching to clocksource MIPS
[ 0.340000] NET: Registered protocol family 2
[ 0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.350000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.360000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.360000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.370000] TCP reno registered
[ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] NET: Registered protocol family 1
[ 0.400000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.400000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.410000] msgmni has been set to 245
[ 0.420000] io scheduler noop registered
[ 0.420000] io scheduler deadline registered (default)
[ 0.430000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.460000] console [ttyS0] enabled, bootconsole disabled
[ 0.460000] console [ttyS0] enabled, bootconsole disabled
[ 0.470000] m25p80 spi0.0: found gd25q16csig, expected m25p80
[ 0.480000] m25p80 spi0.0: gd25q16csig (2048 Kbytes)
[ 0.490000] 3 cmdlinepart partitions found on MTD device spi0.0
[ 0.490000] Creating 3 MTD partitions on "spi0.0":
[ 0.500000] 0x000000000000-0x0000000a0000 : "u-boot"
[ 0.500000] 0x0000000a0000-0x0000000c0000 : "u-boot-env"
[ 0.510000] 0x0000000c0000-0x000000200000 : "reserved1"
[ 0.520000] zte gd nand
[ 0.520000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Giga Device NAND 128MiB 3,3V 8-bit)
[ 0.530000] Scanning device for bad blocks
[ 0.560000] Bad eraseblock 127 at 0x000000fe0000
[ 0.750000] Bad eraseblock 1023 at 0x000007fe0000
[ 0.750000] 14 cmdlinepart partitions found on MTD device spi0.1
[ 0.760000] Creating 14 MTD partitions on "spi0.1":
[ 0.760000] 0x000000000000-0x0000000a0000 : "fota-flag"
[ 0.770000] 0x0000000a0000-0x000000120000 : "art"
[ 0.770000] 0x000000120000-0x0000001a0000 : "mac"
[ 0.780000] 0x0000001a0000-0x000000260000 : "reserved2"
[ 0.790000] 0x000000260000-0x000000660000 : "cfg-param"
[ 0.790000] 0x000000660000-0x000000a60000 : "log"
[ 0.800000] 0x000000a60000-0x000000b00000 : "oops"
[ 0.800000] 0x000000b00000-0x000001000000 : "reserved3"
[ 0.810000] 0x000001000000-0x000001800000 : "web"
[ 0.820000] 0x000001800000-0x000001b00000 : "kernel"
[ 0.820000] 0x000001b00000-0x000003500000 : "rootfs"
[ 0.830000] mtd: partition "rootfs" set to be root filesystem
[ 0.840000] 0x000003500000-0x000004e00000 : "data"
[ 0.840000] 0x000004e00000-0x000008000000 : "fota"
[ 0.850000] 0x000001800000-0x000003500000 : "firmware"
[ 0.990000] ag71xx_mdio: probed
[ 1.000000] zte_nand_local_read():Reading Flash for Calibraton data from 0x0 and partition name is mac
[ 1.010000] ***********************************************
[ 1.010000] AG71XX using MAC@ - using b4:1c:30:8a:82:ce
[ 1.020000] ***********************************************
[ 1.030000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.610000] eth0: Atheros AR8327 switch driver attached.
[ 4.500000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 4.510000] *************tian.zb test err=0***********************
[ 4.520000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 4.530000] zte gpio_keys_polled_check_state:report code=358 state=0
[ 4.530000] zte gpio_keys_polled_check_state:report code=352 state=0
[ 4.540000] zte gpio_keys_polled_check_state:report code=238 state=0
[ 4.550000] netem: version 1.3
[ 4.550000] u32 classifier
[ 4.550000] Performance counters on
[ 4.560000] input device check on
[ 4.560000] Actions configured
[ 4.560000] TCP cubic registered
[ 4.570000] NET: Registered protocol family 17
[ 4.570000] 8021q: 802.1Q VLAN Support v1.8
[ 4.580000] ### of_selftest(): No testcase data in device tree; not running tests
[ 4.610000] VFS: Mounted root (squashfs filesystem) readonly on device 31:13.
[ 4.620000] Freeing unused kernel memory: 228k freed
init started: BusyBox v1.19.4 (2019-09-19 15:57:04 CST)
*****************ZTE rcS********************
call startup scripts here\n
[ 11.470000] ssdk_plat_init start
[ 11.470000] Register QCA PHY driver
[ 11.480000] PHY ID is 0x4dd036
[ 11.580000] qca probe f1 phy driver succeeded!
[ 11.580000] qca-ssdk module init succeeded!
[ 12.130000] NET: Registered protocol family 10
[ 12.540000] SCSI subsystem initialized
[ 13.180000] usbcore: registered new interface driver usbfs
[ 13.180000] usbcore: registered new interface driver hub
[ 13.190000] usbcore: registered new device driver usb
[ 13.200000] Button Hotplug driver version 0.4.1
[ 13.540000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 13.870000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 14.300000] PPP generic driver version 2.4.2
[ 14.540000] tun: Universal TUN/TAP device driver, 1.6
[ 14.550000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 14.580000] NET: Registered protocol family 24
[ 14.660000] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 14.730000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.030000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 15.040000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[ 15.050000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 15.080000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 15.100000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 15.100000] hub 1-0:1.0: USB hub found
[ 15.110000] hub 1-0:1.0: 1 port detected
[ 15.110000] ehci-platform ehci-platform.1: Generic Platform EHCI Controller
[ 15.120000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 15.160000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 15.180000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 15.180000] hub 2-0:1.0: USB hub found
[ 15.190000] hub 2-0:1.0: 1 port detected
[ 15.430000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 15.530000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[ 15.910000] ZTE Generic Netlink Module Inserted without Lock
[ 15.960000] xt_time: kernel timezone is -0000
[ 16.380000] nf_conntrack_rtsp v0.6.21 loading
[ 16.400000] nf_nat_rtsp v0.6.21 loading
[ 16.470000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.630000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 16.920000] AR71XX_RESET_REG_WDOG_CTRL: 0x0
[ 16.920000]
[ 16.990000] cdc_acm 1-1:1.2: This device cannot do calls on its own. It is not a modem.
[ 17.000000] cdc_acm 1-1:1.2: ttyACM0: USB ACM device
[ 17.010000] usbcore: registered new interface driver cdc_acm
[ 17.010000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 17.100000] usbcore: registered new interface driver usbserial
[ 17.110000] USB Serial support registered for generic
[ 17.110000] usbcore: registered new interface driver usbserial_generic
[ 17.120000] usbserial: USB Serial Driver core
[ 17.170000] Initializing USB Mass Storage driver...
[ 17.180000] usbcore: registered new interface driver usb-storage
[ 17.190000] USB Mass Storage support registered.
[ 17.200000] usbcore: registered new interface driver cdc_ether
[ 17.280000] generic_rndis_bind: rx_urb_size: 0x3e80
[ 17.290000] generic_rndis_bind: data zero copy=1
[ 17.290000] driver_info->flags 3238 idVendor 19d2 idProduct 1489
[ 17.300000] rndis_host 1-1:1.0: usb0: register 'rndis_host' at usb-ehci-platform.0-1, RNDIS device, ee:cc:32:20:7d:c6
[ 17.310000] usbcore: registered new interface driver rndis_host
[ 17.380000] USB Serial support registered for GSM modem (1-port)
[ 17.380000] usbcore: registered new interface driver option
[ 17.390000] option: v0.7.2:USB Driver for GSM modems
[ 17.450000] fuse init (API version 7.18)
[ 18.250000] yaffs: dev is 32505864 name is "mtdblock8" rw
[ 18.250000] yaffs: passed flags ""
[ 18.320000] yaffs: dev is 32505871 name is "mtdblock15" rw
[ 18.320000] yaffs: passed flags ""
rm: can't remove '/etc_rw/fota/cp_failure_flag': No such file or directory
SOS: FLAG is mtdblock7
SOS: /etc_rw/fota/cfg_partiton_flag has [ 19.630000] yaffs: dev is 32505863 name is "mtdblock7" rw
content
[ 19.640000] yaffs: passed flags ""
space usage of /etc_rw/config is 27%
[ 19.800000] yaffs: dev is 32505866 name is "mtdblock10" rw
[ 19.810000] yaffs: passed flags ""
[ 19.840000] ath79_spinand_read_page ecc err status=0x2
SOS: /etc_rw/config use mtdblock7, /zte_backup use mtdblock10, now doing backup!
rm: can't remove '/zte_backup/lost+found': Directory not empty
[ 21.600000] Load cfg new driver...
[ 21.600000] cfg init, /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 577
[ 21.610000]
[ 21.620000] wifi_chip1_ssid2_acc
[ 21.620000] 776966695f63686970315f73736964325f616363
[ 21.720000]
[ 21.720000] cfg init end, /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 636
[ 21.730000] cfg init, /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 577
[ 21.740000]
[ 21.740000] TESTBITSIGNINFO=0000
[ 21.750000] 544553544249545349474e494e464f3d30303030
[ 21.750000]
[ 21.750000] cfg init end, /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/cfg-1.0/cfg_param.c 636
[ 21.790000] usbcore: registered new interface driver cdc_wdm
[ 22.250000] usbcore: registered new interface driver qmi_wwan
mkdir: can't create directory '/dev/net': File exists
mknod: dev/net/tun: File exists
killall: syslogd: no process killed
*************ZTE Init Script*************
insmod: can't insert '/lib/modules/3.3.8/xt_time.ko': File exists
rmmod: can't unload 'shortcut_fe_drv': unknown symbol in module, or unknown parameter
[ 23.480000] usbcore: registered new interface driver cdc_ncm
enter is_fota_update_successed.
find a good block.
last find blk_num = 0
****fota_update_flag in /dev/mtd3 is
****
Unable to open pidfile /var/run/nvramd.pid: No such file or directory
reboot_schedule is disabled
Create bridge br0..........
monitor:add@/devices/virtual/net/br0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/br0
monitor:SUBSYSTEM=net
monitor:DEVTYPE=bridge
monitor:INTERFACE=br0
monitor:IFINDEX=6
monitor:SEQNUM=625
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/br0/queues/tx-0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/br0/queues/tx-0
monitor:SUBSYSTEM=queues
monitor:SEQNUM=626
monitor:event { 'add', '' }
/etc/init.d/rcS: /etc/init.d/zte_init.sh: line 84: telnetd: not found
[ 26.850000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 28.690000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 28.700000] eth0: link up (1000Mbps/Full duplex)
[ 28.710000]
[ 28.710000] /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[177]: ERROR:Build msg struct failed, snd_pid=-1, genl_switch=1!
[ 29.730000] eth0: link up (1000Mbps/Full duplex)
[ 29.740000]
[ 29.740000] /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[177]: ERROR:Build msg struct failed, snd_pid=-1, genl_switch=1!
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
SSDK Init OK!
operate done.
monitor:add@/devices/virtual/net/eth0.1
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/eth0.1
monitor:SUBSYSTEM=net
monitor:INTERFACE=eth0.1
monitor:IFINDEX=7
monitor:SEQNUM=627
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/eth0.1/queues/tx-0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/eth0.1/queues/tx-0
monitor:SUBSYSTEM=queues
monitor:SEQNUM=628
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/eth0.2
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/eth0.2
monitor:SUBSYSTEM=net
monitor:INTERFACE=eth0.2
monitor:IFINDEX=8
monitor:SEQNUM=629
monitor:event { 'add', '' }
monitor:add@/devices/virtual/net/eth0.2/queues/tx-0
monitor:ACTION=add
monitor:DEVPATH=/devices/virtual/net/eth0.2/queues/tx-0
monitor:SUBSYSTEM=queues
monitor:SEQNUM=630
monitor:event { 'add', '' }
opms_wan_ifname=usb0
LanIfName=br0
CURRENT WAN MODE:PPP
dual_core_board_if= ....
ifconfig: SIOCSIFADDR: No such device
[ 35.350000]
[ 35.350000] /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[197]: INFO:Recv from userspace: [Connect request from userspace
[ 35.360000] ]
[ 35.370000]
[ 35.370000] /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[169]: INFO:send msg to user ok, cmd=1, msg=1000
[ 35.390000]
[ 35.390000] /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[169]: INFO:send msg to user ok, cmd=3, msg=
zte_wifi_dfs_status_process: dfs=[]
goahead initWebs info: webdir is /etc_ro/web/web!
webs: Listening for HTTP requests at address 192.168.0.1
Cannot find device "ecm0"
internet.sh is called, the argument is []
killall: pppoecd: no process killed
killall: udhcpc: no process killed
killall: zte_router: no process killed
killall: zte_trx_router: no process killed
killall: udhcpd: no process killed
killall: dnsmasq: no process killed
killall: miniupnpd: no process killed
passwd: no record of admin in /etc/shadow, using /etc/passwd
Changing password for admin
New password:
Retype password:
Password for admin changed by admin
call setPortAsAllLAN............
lan_ip: 192.168.0.1, lan_netmask: 255.255.255.0..........
[ 36.990000] device eth0.1 entered promiscuous mode
[ 36.990000] device eth0 entered promiscuous mode
[ 37.000000] br0: port 1(eth0.1) entered forwarding state
[ 37.000000] br0: port 1(eth0.1) entered forwarding state
[ 37.010000] device eth0.2 entered promiscuous mode
[ 37.020000] br0: port 2(eth0.2) entered forwarding state
[ 37.020000] br0: port 2(eth0.2) entered forwarding state
opms_wan_ifname=usb0
[ 37.100000] br0: port 1(eth0.1) entered forwarding state
[ 37.120000] br0: port 2(eth0.2) entered forwarding state
webs: Listening for HTTPS requests at port 443
opms_wan_ifname=usb0
LanIfName=br0
killall: udhcpd: no process killed
killall: dnsmasq: no process killed
* daemon not running. starting it now on port 5037 *
enter launch_server server_port is 5037
launch_server pipe path & pid: /usr/bin/adb, 849
launch_server pipe path & pid: /usr/bin/adb, 0
pid=0 and server_port is : 5037
launch_server temp value: O,K,
* daemon started successfully *
begin
middle
else section
mang_num: -1
list_first_item:
one_num: -1
###the format of mac_ip_list is valid###
begin
middle
else section
mang_num: -1
list_first_item:
one_num: -1
###the format of mac_ip_list is valid###
opms_wan_ifname=usb0
LanIfName=br0
#######start the mtu_set.sh##########
192.168.0.1255.255.255.0init_dns_ip:tmp_byte_netmask is 0
init_dns_ip:tmp_byte_netmask is 255
init_dns_ip:tmp_byte_netmask is 255
init_dns_ip:tmp_byte_netmask is 255
#######end the mtu_set.sh##########
iptables: Index of deletion too big.
enter setVoipPortAsLAN()...
zte_port_status_monitor_create_msg_queue(): msgid = [229383]
Sat Jan 1 00:00:00 UTC 2000
3 KB/s (146 bytes in 0.043s)
exit
opms_wan_ifname=usb0
LanIfName=br0
iptables v1.4.10: Couldn't load target `remote_mark':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
[ 44.100000] set 1
ip6tables: No chain/target/match by that name.
normal mode!
Please press Enter to activate this console. ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
/bin/sh: zte_user_connect: not found
opms_wan_ifname=usb0
LanIfName=br0
killall: miniupnpd: no process killed
opms_wan_ifname=usb0
LanIfName=br0
iptables: No chain/target/match by that name.
3 KB/s (150 bytes in 0.043s)
3 KB/s (150 bytes in 0.041s)
2 KB/s (150 bytes in 0.052s)
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
[ 47.700000] +++++++http_redirect load, g_web_redirect_gateway=[192.168.0.1]...
[ 47.700000] +++++++http_redirect load, g_web_redirect_mode=[http]...
monitor:add@/module/zte_http_redirect
monitor:ACTION=add
monitor:DEVPATH=/module/zte_http_redirect
monitor:SUBSYSTEM=module
monitor:SEQNUM=631
monitor:event { 'add', '' }
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
iptables v1.4.10: Couldn't load target `MINIUPNPD':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
/dev/mtdblock15 on /etc_rw/fota type yaffs2 (rw,relatime)
mtdblock15 already mounted!
/etc/miniupnpd.conf already exist!
[ 47.870000]
[ 47.870000] /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[197]: INFO:Recv from userspace: [5]
[ 48.080000]
[ 48.080000] /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[197]: INFO:Recv from userspace: [5]
[ 48.140000]
[ 48.140000] /home/scl/ci/workspace/Soft4_MF286R1_TMOPL_CPE/qsdk/build_dir/linux-ar71xx_generic/zte_genl_kernel-1.0/zte_genl_kernel_main.c[197]: INFO:Recv from userspace: [5]
/etc/miniupnpd.conf already exist!
opms_wan_ifname=usb0
LanIfName=br0
path: etc_rw...
enter the wifi_create_0 function
path: etc_rw...
enter the wifi_create_2 function
path: etc_rw...
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
path: etc_rw...
enter the wifi_create_3 function
enter the wifi_create_1 function
Jan 1 00:00:08 miniupnpd[1353]: HTTP listening on port 10010
Jan 1 00:00:08 miniupnpd[1353]: Listening for NAT-PMP/PCP traffic on port 5351
************start dos_attack_defender.sh*****************
iptables: No chain/target/match by that name.
iptables v1.4.10: Couldn't load target `dosattack_filter':File not found
Try `iptables -h' or 'iptables --help' for more information.
iptables: No chain/target/match by that name.
************end dos_attack_defender.sh*****************
insmod: can't insert '/lib/modules/3.3.8/nf_conntrack_sip.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_nat_sip.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_conntrack_pptp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_nat_pptp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_conntrack_ftp.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/nf_nat_ftp.ko': File exists
opms_wan_ifname=usb0
LanIfName=br0
iptables: No chain/target/match by that name.
iptables: Chain already exists.
ip6tables: Chain already exists.
qrcode_text = WIFI:T:WPA;S:MF286_8A83CE;P:2Y2432C6N6;
opms_wan_ifname=usb0
LanIfName=br0
opms_wan_ifname=usb0
LanIfName=br0
iptables: No chain/target/match by that name.
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
iptables: No chain/target/match by that name.
/etc/miniupnpd.conf already exist!
/etc/miniupnpd.conf already exist!
route: SIOCADDRT: File exists
opms_wan_ifname=usb0
LanIfName=br0
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Jan 1 00:00:10 miniupnpd[1533]: HTTP listening on port 10010
Jan 1 00:00:10 miniupnpd[1533]: Listening for NAT-PMP/PCP traffic on port 5351
************start dos_attack_defender.sh*****************
iptables: No chain/target/match by that name.
************end dos_attack_defender.sh*****************
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
qrcode_text = WIFI:T:WPA;S:MF286_8A83CE_2;P:2BDD2N7Q2R;
qrcode_text = WIFI:T:WPA;S:MF286_5G_8A83CE_2;P:2BDD2N7Q2R;
qrcode_text = WIFI:T:WPA;S:MF286_5G_8A83CE;P:2Y2432C6N6;
Reading chip1_ssid1_qr .
Reading chip1_ssid1_qr o
Read OK chip1_ssid1_qr
Reading chip1_ssid2_qr .
Reading chip1_ssid2_qr o
Read OK chip1_ssid2_qr
Writing chip1_ssid1_qr
OK chip1_ssid1_qr
Writing chip1_ssid2_qr
OK chip1_ssid2_qr
Reading chip2_ssid2_qr .
Reading chip2_ssid2_qr o
Read OK chip2_ssid2_qr
Writing chip2_ssid2_qr
OK chip2_ssid2_qr
Reading chip2_ssid1_qr .
Reading chip2_ssid1_qr o
Read OK chip2_ssid1_qr
Writing chip2_ssid1_qr
OK chip2_ssid1_qr
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
whitelist=[]
enter add_remote_mgr_fw_items()
add remote manager done.
enter add_telnet()
disable telnetd on lan side
00:00:11 UP>>[update_control.c:2870]########---Update_Control Start---########
00:00:11 UP>>[update_control.c:2872]modem is ASR_MODEM
firewall_sys_fw done
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe-ipv6.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe-cm.ko': File exists
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe-ipv6.ko': File exists
insmod: can't insert '/lib/modules/3.3.8/shortcut-fe-cm.ko': File exists
speed limit is disabled, so we need to enable SFE,clear iptable and tc rules
iptables: No chain/target/match by that name.
iptables: No chain/target/match by that name.
RTNETLINK answers: Invalid argument
RTNETLINK answers: Invalid argument
/sbin/second_ssid_access_control.sh: line 17: ebtables: not found
/sbin/second_ssid_access_control.sh: line 18: ebtables: not found
/sbin/second_ssid_access_control.sh: line 19: ebtables: not found
/sbin/second_ssid_access_control.sh: line 20: ebtables: not found
/sbin/second_ssid_access_control.sh: line 21: ebtables: not found
/sbin/second_ssid_access_control.sh: line 83: ebtables: not found
/sbin/second_ssid_access_control.sh: line 83: ebtables: not found
/sbin/second_ssid_access_control.sh: line 83: ebtables: not found
/sbin/second_ssid_access_control.sh: line 83: ebtables: not found
/sbin/second_ssid_access_control.sh: line 83: ebtables: not found
/sbin/second_ssid_access_control.sh: line 83: ebtables: not found
/sbin/second_ssid_access_control.sh: line 83: ebtables: not found
/sbin/second_ssid_access_control.sh: line 83: ebtables: not found
BusyBox v1.19.4 (2019-09-19 15:57:04 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
MM NM MMMMMMM M M
$MMMMM MMMMM MMMMMMMMMMM MMM MMM
MMMMMMMM MM MMMMM. MMMMM:MMMMMM: MMMM MMMMM
MMMM= MMMMMM MMM MMMM MMMMM MMMM MMMMMM MMMM MMMMM'
MMMM= MMMMM MMMM MM MMMMM MMMM MMMM MMMMNMMMMM
MMMM= MMMM MMMMM MMMMM MMMM MMMM MMMMMMMM
MMMM= MMMM MMMMMM MMMMM MMMM MMMM MMMMMMMMM
MMMM= MMMM MMMMM, NMMMMMMMM MMMM MMMM MMMMMMMMMMM
MMMM= MMMM MMMMMM MMMMMMMM MMMM MMMM MMMM MMMMMM
MMMM= MMMM MM MMMM MMMM MMMM MMMM MMMM MMMM
MMMM$ ,MMMMM MMMMM MMMM MMM MMMM MMMMM MMMM MMMM
MMMMMMM: MMMMMMM M MMMMMMMMMMMM MMMMMMM MMMMMMM
MMMMMM MMMMN M ten kod uruchomiłem gdy system już wstał i sobie podmontował po swojemu
for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16; do echo "partycja $i"; cat /dev/mtd$i > /tmp/usb_disk/mtd$i; sync; echo "partycja $i zrobiona" ; doneadmin@(none):~# mount
rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime,size=63008k)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
tmpfs on /etc type tmpfs (rw,relatime)
/dev/mtdblock11 on /etc_ro/web type cramfs (ro,relatime)
/dev/mtdblock8 on /etc_rw/log type yaffs2 (rw,relatime)
/dev/mtdblock15 on /etc_rw/fota type yaffs2 (rw,relatime)
/dev/mtdblock7 on /etc_rw/config type yaffs2 (rw,relatime)
/dev/mtdblock10 on /zte_backup type yaffs2 (rw,relatime)
none on /sys/kernel/debug type debugfs (rw,relatime)jeśli trzeba to zrobić inaczej to dajcie znać proszę.
obrazy partycji, wszystkie w zipie
geos.ct8.pl/geos.mtd.zip
wracam teraz do pracy, ale jak coś porzeba więcej to napiszcie, wieczorem popatrzę.
Podaj jeszcze wersję softu która to była to wstawię do siebie.
Czy to "Soft4_MF286R1_TMOPL_CPE" sugeruje , że to jest MF286R1 i to też jakaś podwersja ?
@Cezary, czy chodzi o to co w poście 788 czy o coś innego?
Tak, może być. Przegapiłem to.
Umieściłem to na https://dl.eko.one.pl/orig/zte_mf286r/PLUS/
Strony Poprzednia 1 … 30 31 32 33 34 … 50 Następna
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Sprzęt / Hardware → ZTE MF286R - OpenWrt
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc