26

Odp: Netgear R6220 instalacje OpenWrt

Napisz który wiersz uważasz za błąd? Serio się pytam.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

27

Odp: Netgear R6220 instalacje OpenWrt

Przepraszam....moja wina i brak wiedzy.
Rzuć proszę okiem na to:

root@OpenWrt:~# dmesg
[    0.000000] Linux version 4.14.109 (er2de2@Lenovo) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7628-61323d22c0)) #0 SMP Fri Mar 29 17:04:39 2019
[    0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] MIPS: machine is Netgear R6220
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] VPE topology {2} total 2
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000]   HighMem  empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 80552020, node_mem_map 81003000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] random: get_random_bytes called from 0x80555740 with crng_init=0
[    0.000000] percpu: Embedded 14 pages/cpu @8110f000 s26256 r8192 d22896 u57344
[    0.000000] pcpu-alloc: s26256 r8192 d22896 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00041450
[    0.000000] Readback ErrCtl register=00041450
[    0.000000] Memory: 123780K/131072K available (4639K kernel code, 236K rwdata, 572K rodata, 236K init, 254K bss, 7292K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 256
[    0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[    0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[    0.015491] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[    0.087799] pid_max: default: 32768 minimum: 301
[    0.097097] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110114] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.125634] Hierarchical SRCU implementation.
[    0.134886] smp: Bringing up secondary CPUs ...
[    0.144363] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.144372] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.144383] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.144513] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.204377] Synchronize counters for CPU 1: done.
[    0.264040] smp: Brought up 1 node, 2 CPUs
[    0.275507] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.294976] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.307195] pinctrl core: initialized pinctrl subsystem
[    0.318117] NET: Registered protocol family 16
[    0.333538] FPU Affinity set after 11720 emulations
[    0.334367] pull PCIe RST: RALINK_RSTCTRL = 0
[    0.643319] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.653392] ***** Xtal 40MHz *****
[    0.660115] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.670323] Port 0 N_FTS = 1b105000
[    0.677218] Port 1 N_FTS = 1b102800
[    0.684143] Port 2 N_FTS = 1b105000
[    1.842597] PCIE1 no card, disable it(RST&CLK)
[    1.851289]  -> 12007f2
[    1.856105] PCIE0 enabled
[    1.861302] PCIE2 enabled
[    1.866484] PCI host bridge /pcie@1e140000 ranges:
[    1.876013]  MEM 0x0000000060000000..0x000000006fffffff
[    1.886366]   IO 0x000000001e160000..0x000000001e16ffff
[    1.896737] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[    1.922704] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.934178] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.945392] mt7621_gpio 1e000600.gpio: registering 32 gpios
[    1.957709] PCI host bridge to bus 0000:00
[    1.965736] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.979389] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    1.991126] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    2.004608] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    2.020377] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[    2.020418] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    2.020430] pci 0000:00:00.0: reg 0x14: [mem 0x60300000-0x6030ffff]
[    2.020493] pci 0000:00:00.0: supports D1
[    2.020502] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    2.020781] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[    2.020819] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    2.020840] pci 0000:00:01.0: reg 0x14: [mem 0x60310000-0x6031ffff]
[    2.020911] pci 0000:00:01.0: supports D1
[    2.020925] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[    2.021432] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[    2.021501] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[    2.021559] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[    2.021658] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    2.021863] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    2.022114] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
[    2.022175] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[    2.022322] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[    2.022549] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[    2.022573] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
[    2.022648] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    2.035678] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.049493] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[    2.062624] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[    2.076453] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    2.089927] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref]
[    2.104271] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff]
[    2.117752] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[    2.131231] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[    2.144727] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    2.159234] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref]
[    2.173561] pci 0000:00:00.0: PCI bridge to [bus 01]
[    2.183402] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    2.196893] pci 0000:00:00.0:   bridge window [mem 0x60100000-0x601fffff pref]
[    2.211238] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff]
[    2.224715] pci 0000:00:01.0: PCI bridge to [bus 02]
[    2.234548] pci 0000:00:01.0:   bridge window [mem 0x60200000-0x602fffff]
[    2.249625] clocksource: Switched to clocksource GIC
[    2.261039] NET: Registered protocol family 2
[    2.270416] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    2.284152] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    2.296762] TCP: Hash tables configured (established 1024 bind 1024)
[    2.309481] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    2.320977] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    2.333612] NET: Registered protocol family 1
[    2.342191] PCI: CLS 0 bytes, default 32
[    2.579572] 4 CPUs re-calibrate udelay(lpj = 2924544)
[    2.590625] Crashlog allocated RAM at address 0x3f00000
[    2.601243] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    2.622256] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.633758] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.657025] io scheduler noop registered
[    2.664763] io scheduler deadline registered (default)
[    2.675928] gpio-export gpio_export: 1 gpio(s) exported
[    2.687121] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    2.703517] console [ttyS0] disabled
[    2.710600] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 14, base_baud = 3125000) is a 16550A
[    2.728505] console [ttyS0] enabled
[    2.742301] bootconsole [early0] disabled
[    2.759002] cacheinfo: Failed to find cpu0 device node
[    2.769282] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    2.782346] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[    2.796338] Enable NFI Clock
[    2.802115] # MTK NAND # : Use HW ECC
[    2.809407] Device not found, ID: c2f1
[    2.816861] Not Support this Device!
[    2.824321] chip_mode=00000001
[    2.830399] Support this Device in MTK table! c2f1
[    2.840288] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[    2.853153] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[    2.865795] nand: Macronix NAND 128MiB 3,3V 8-bit
[    2.875156] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    2.890240] Scanning device for bad blocks
[    3.064211] Bad eraseblock 700 at 0x000005780000
[    3.149929] 6 fixed-partitions partitions found on MTD device MT7621-NAND
[    3.163439] Creating 6 MTD partitions on "MT7621-NAND":
[    3.173844] 0x000000000000-0x000000100000 : "u-boot"
[    3.184871] 0x000000100000-0x000000200000 : "SC PID"
[    3.195790] 0x000000200000-0x000000600000 : "kernel"
[    3.206765] 0x000000600000-0x000002200000 : "ubi"
[    3.217357] 0x000002e00000-0x000002f00000 : "factory"
[    3.228484] 0x000004200000-0x000007e00000 : "reserved"
[    3.240281] [mtk_nand] probe successfully!
[    3.249128] Signature matched and data read!
[    3.257626] load_fact_bbt success 1023
[    3.265852] libphy: Fixed MDIO Bus: probed
[    3.342186] libphy: mdio: probed
[    4.748220] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[    4.760752] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 16
[    4.780138] NET: Registered protocol family 10
[    4.790363] Segment Routing with IPv6
[    4.797729] NET: Registered protocol family 17
[    4.806698] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    4.832493] 8021q: 802.1Q VLAN Support v1.8
[    4.844050] UBI: auto-attach mtd3
[    4.850696] ubi0: attaching mtd3
[    5.114374] ubi0: scanning is finished
[    5.136911] ubi0: attached mtd3 (name "ubi", size 28 MiB)
[    5.147685] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    5.161375] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    5.174883] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    5.188741] ubi0: good PEBs: 224, bad PEBs: 0, corrupted PEBs: 0
[    5.200701] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[    5.215076] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 2007613359
[    5.233258] ubi0: available PEBs: 0, total reserved PEBs: 224, PEBs reserved for bad PEB handling: 20
[    5.251631] ubi0: background thread "ubi_bgt0d" started, PID 354
[    5.253471] block ubiblock0_0: created from ubi0:0(rootfs)
[    5.274549] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[    5.288419] hctosys: unable to open rtc device (rtc0)
[    5.305053] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    5.319963] Freeing unused kernel memory: 236K
[    5.328810] This architecture does not have kernel memory protection.
[    5.381201] random: fast init done
[    5.880221] init: Console is alive
[    5.887238] init: - watchdog -
[    6.436424] mtk_soc_eth 1e100000.ethernet eth0: port 0 link up
[    6.860048] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    6.958954] usbcore: registered new interface driver usbfs
[    6.970075] usbcore: registered new interface driver hub
[    6.980801] usbcore: registered new device driver usb
[    7.014696] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.033982] SCSI subsystem initialized
[    7.044786] ehci-platform: EHCI generic platform driver
[    7.062902] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    7.073575] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[    7.099812] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[    7.118133] xhci-mtk 1e1c0000.xhci: irq 15, io mem 0x1e1c0000
[    7.130625] hub 1-0:1.0: USB hub found
[    7.138164] hub 1-0:1.0: 2 ports detected
[    7.146811] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[    7.157444] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[    7.172374] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0  SuperSpeed
[    7.185387] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    7.202420] hub 2-0:1.0: USB hub found
[    7.209989] hub 2-0:1.0: 1 port detected
[    7.223581] usbcore: registered new interface driver usb-storage
[    7.237029] usbcore: registered new interface driver uas
[    7.247879] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    7.280084] init: - preinit -
[    7.799743] usb 1-2: new high-speed USB device number 2 using xhci-mtk
[    8.013696] mtk_soc_eth 1e100000.ethernet: PPE started
[    8.099450] hub 1-2:1.0: USB hub found
[    8.107609] hub 1-2:1.0: 4 ports detected
[    8.118293] random: procd: uninitialized urandom read (4 bytes read)
[    8.439622] usb 1-2.2: new high-speed USB device number 3 using xhci-mtk
[    8.657510] usb-storage 1-2.2:1.2: USB Mass Storage device detected
[    8.670520] scsi host0: usb-storage 1-2.2:1.2
[    9.750922] scsi 0:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
[    9.769471] sd 0:0:0:0: [sda] Optimal transfer size 0 bytes < PAGE_SIZE (4096 bytes)
[    9.786324] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   11.263674] mount_root: loading kmods from internal overlay
[   11.293273] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[   11.308542] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   11.728367] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 500
[   11.801263] UBIFS (ubi0:1): recovery needed
[   11.951326] UBIFS (ubi0:1): recovery completed
[   11.960325] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   11.975914] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   11.995655] UBIFS (ubi0:1): FS size: 21078016 bytes (20 MiB, 166 LEBs), journal size 1015809 bytes (0 MiB, 8 LEBs)
[   12.016258] UBIFS (ubi0:1): reserved for root: 995566 bytes (972 KiB)
[   12.029086] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 1679E461-F1D6-472C-A4F1-2503CE2778B6, small LPT model
[   12.053645] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   12.076367] block: extroot: not configured
[   12.129856] UBIFS (ubi0:1): un-mount UBI device 0
[   12.139236] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[   12.157567] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 503
[   12.328569] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[   12.344220] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[   12.363964] UBIFS (ubi0:1): FS size: 21078016 bytes (20 MiB, 166 LEBs), journal size 1015809 bytes (0 MiB, 8 LEBs)
[   12.384567] UBIFS (ubi0:1): reserved for root: 995566 bytes (972 KiB)
[   12.397396] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 1679E461-F1D6-472C-A4F1-2503CE2778B6, small LPT model
[   12.629316] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[   12.650946] block: extroot: not configured
[   12.702428] mount_root: switching to ubifs overlay
[   12.739376] urandom-seed: Seeding with /etc/urandom.seed
[   12.821973] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[   12.843681] procd: - early -
[   12.849508] procd: - watchdog -
[   13.315666] random: jshn: uninitialized urandom read (4 bytes read)
[   13.475919] random: jshn: uninitialized urandom read (4 bytes read)
[   13.529903] procd: - watchdog -
[   13.536554] procd: - ubus -
[   13.557364] random: ubusd: uninitialized urandom read (4 bytes read)
[   13.604113] procd: - init -
[   14.162766] kmodloader: loading kernel modules from /etc/modules.d/*
[   14.193721] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.215983] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[   14.232031] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   14.248117] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.268433] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[   14.341071] xt_time: kernel timezone is -0000
[   14.382970] cdc_ether 1-2.2:1.0 eth1: register 'cdc_ether' at usb-1e1c0000.xhci-2.2, CDC Ethernet Device, 0c:5b:8f:27:9a:64
[   14.405679] usbcore: registered new interface driver cdc_ether
[   14.500173] bus=0x2, slot = 0x1, irq=0xff
[   14.508391] mt7603e 0000:02:00.0: ASIC revision: 76030010
[   15.550877] mt7603e 0000:02:00.0: Firmware Version: ap_pcie
[   15.562053] mt7603e 0000:02:00.0: Build Time: 20160107100755
[   15.609625] mt7603e 0000:02:00.0: firmware init done
[   15.784950] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   15.803002] bus=0x1, slot = 0x0, irq=0xff
[   15.811294] mt76x2e 0000:01:00.0: ASIC revision: 76120044
[   16.480218] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
[   16.495919] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
[   16.506875] mt76x2e 0000:01:00.0: Build: 1
[   16.515033] mt76x2e 0000:01:00.0: Build Time: 201507311614____
[   16.549629] mt76x2e 0000:01:00.0: Firmware running!
[   16.560704] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[   16.572747] PPP generic driver version 2.4.2
[   16.584326] NET: Registered protocol family 24
[   16.597343] kmodloader: done loading kernel modules from /etc/modules.d/*
[   22.853029] mtk_soc_eth 1e100000.ethernet: PPE started
[   22.869444] device eth0 entered promiscuous mode
[   22.885951] br-lan: port 1(eth0.1) entered blocking state
[   22.897148] br-lan: port 1(eth0.1) entered disabled state
[   22.908416] device eth0.1 entered promiscuous mode
[   22.924588] br-lan: port 1(eth0.1) entered blocking state
[   22.935432] br-lan: port 1(eth0.1) entered forwarding state
[   22.946969] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   22.984038] cdc_ether 1-2.2:1.0 eth1: kevent 12 may have been dropped
[   22.985403] cdc_ether 1-2.2:1.0 eth1: kevent 11 may have been dropped
[   23.910213] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   26.477503] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   26.499012] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   26.511381] br-lan: port 2(wlan1) entered blocking state
[   26.522158] br-lan: port 2(wlan1) entered disabled state
[   26.533344] device wlan1 entered promiscuous mode
[   26.548659] br-lan: port 3(wlan0) entered blocking state
[   26.559363] br-lan: port 3(wlan0) entered disabled state
[   26.570594] device wlan0 entered promiscuous mode
[   26.580402] br-lan: port 3(wlan0) entered blocking state
[   26.591060] br-lan: port 3(wlan0) entered forwarding state
[   27.002521] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   27.667200] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   27.680181] br-lan: port 2(wlan1) entered blocking state
[   27.690810] br-lan: port 2(wlan1) entered forwarding state
[   61.595656] random: crng init done
[   61.602437] random: 6 urandom warning(s) missed due to ratelimiting
Netgear R6220 + HUAWEI E3372 Hilink

28

Odp: Netgear R6220 instalacje OpenWrt

To jest to co poprzednio. I  nadal się pytam: które linie?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

29

Odp: Netgear R6220 instalacje OpenWrt

Wszystko ok, naczytałam się o problemach z wifi, o problemach z podziałem partycji itd,itd, dlatego wrzucilam te logi,żeby kompetentna osoba
sprawdziła, czy wszystko gra.
Teraz wiem, że jest ok. Dziękuję szefie:)

Netgear R6220 + HUAWEI E3372 Hilink

30

Odp: Netgear R6220 instalacje OpenWrt

Napisałaś "Niestety są też błędy w logach." więc pytam się co uważasz za błędy, bo to normalny bootlog jest.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

31

Odp: Netgear R6220 instalacje OpenWrt

Napisałam tak, bo jestem zielona..... napisałam na tej podstawie......proszę się nie śmiać:)

root@OpenWrt:~# logread | grep err
Mon Apr  1 15:51:52 2019 kern.err kernel: [    2.759002] cacheinfo: Failed to find cpu0 device node
Mon Apr  1 15:51:52 2019 kern.warn kernel: [    2.782346] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
Mon Apr  1 15:51:56 2019 daemon.err block: /dev/ubiblock0_0 is already mounted on /rom
Mon Apr  1 15:51:56 2019 daemon.err block: /dev/ubi0_1 is already mounted on /overlay
Mon Apr  1 15:51:58 2019 kern.err kernel: [   22.984038] cdc_ether 1-2.2:1.0 eth1: kevent 12 may have been dropped
Mon Apr  1 15:51:58 2019 kern.err kernel: [   22.985403] cdc_ether 1-2.2:1.0 eth1: kevent 11 may have been dropped
Mon Apr  1 15:51:58 2019 daemon.err odhcp6c[1495]: Failed to send RS (Address not available)
Mon Apr  1 15:52:01 2019 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Mon Apr  1 15:52:01 2019 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Mon Apr  1 15:52:01 2019 daemon.err hostapd: Using interface wlan0 with hwaddr 9c:3d:cf:c7:16:18 and ssid "Netgear_R6220"
Mon Apr  1 15:52:01 2019 daemon.err hostapd: Using interface wlan1 with hwaddr 9c:3d:cf:c7:16:1c and ssid "Netgear_R6220"
Netgear R6220 + HUAWEI E3372 Hilink

32

Odp: Netgear R6220 instalacje OpenWrt

Nie, wszystko gra. Ostatnie 4 są błędnie kwalifikowane jako .err, powinny być jako info, odhcpd nie działa bo ipv6 nie używasz, sterownik od ncm wali debugiem od eventów który dostaje, partycje ubifs są już wcześniej zamontowane bo ten router z nich od razu korzysta itd.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

33 (edytowany przez karolinka 2019-04-02 05:02:29)

Odp: Netgear R6220 instalacje OpenWrt

Jeszcze raz dziękuję.
Jeszcze jedna kwestia, nie mogę ustawić wyższego kanału niż 48 na 5ghz.
Jeśli ustawię kanał np 100, nie mam radia 5ghz

root@OpenWrt:~# iw phy1 info
Wiphy phy1
        max # scan SSIDs: 4
        max scan IEs length: 2247 bytes
        max # sched scan SSIDs: 0
        max # match sets: 0
        max # scan plans: 1
        max scan plan interval: -1
        max scan plan iterations: 0
        Retry short limit: 7
        Retry long limit: 4
        Coverage class: 0 (up to 0m)
        Available Antennas: TX 0x3 RX 0x3
        Configured Antennas: TX 0x3 RX 0x3
        Supported interface modes:
                 * IBSS
                 * managed
                 * AP
                 * AP/VLAN
                 * monitor
                 * mesh point
        Band 2:
                Capabilities: 0x1ff
                        RX LDPC
                        HT20/HT40
                        SM Power Save disabled
                        RX Greenfield
                        RX HT20 SGI
                        RX HT40 SGI
                        TX STBC
                        RX STBC 1-stream
                        Max AMSDU length: 3839 bytes
                        No DSSS/CCK HT40
                Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
                Minimum RX AMPDU time spacing: 4 usec (0x05)
                HT TX/RX MCS rate indexes supported: 0-15
                VHT Capabilities (0x018001b0):
                        Max MPDU length: 3895
                        Supported Channel Width: neither 160 nor 80+80
                        RX LDPC
                        short GI (80 MHz)
                        TX STBC
                VHT RX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: not supported
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT RX highest supported: 0 Mbps
                VHT TX MCS set:
                        1 streams: MCS 0-9
                        2 streams: MCS 0-9
                        3 streams: not supported
                        4 streams: not supported
                        5 streams: not supported
                        6 streams: not supported
                        7 streams: not supported
                        8 streams: not supported
                VHT TX highest supported: 0 Mbps
                Frequencies:
                        * 5180 MHz [36] (20.0 dBm)
                        * 5200 MHz [40] (20.0 dBm)
                        * 5220 MHz [44] (20.0 dBm)
                        * 5240 MHz [48] (20.0 dBm)
                        * 5260 MHz [52] (20.0 dBm) (radar detection)
                        * 5280 MHz [56] (20.0 dBm) (radar detection)
                        * 5300 MHz [60] (20.0 dBm) (radar detection)
                        * 5320 MHz [64] (20.0 dBm) (radar detection)
                        * 5500 MHz [100] (27.0 dBm) (radar detection)
                        * 5520 MHz [104] (27.0 dBm) (radar detection)
                        * 5540 MHz [108] (27.0 dBm) (radar detection)
                        * 5560 MHz [112] (27.0 dBm) (radar detection)
                        * 5580 MHz [116] (27.0 dBm) (radar detection)
                        * 5600 MHz [120] (27.0 dBm) (radar detection)
                        * 5620 MHz [124] (27.0 dBm) (radar detection)
                        * 5640 MHz [128] (27.0 dBm) (radar detection)
                        * 5660 MHz [132] (27.0 dBm) (radar detection)
                        * 5680 MHz [136] (27.0 dBm) (radar detection)
                        * 5700 MHz [140] (27.0 dBm) (radar detection)
                        * 5745 MHz [149] (disabled)
                        * 5765 MHz [153] (disabled)
                        * 5785 MHz [157] (disabled)
                        * 5805 MHz [161] (disabled)
                        * 5825 MHz [165] (disabled)
        valid interface combinations:
                 * #{ IBSS } <= 1, #{ managed, AP, mesh point } <= 8,
                   total <= 8, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz }

        HT Capability overrides:
                 * MCS: ff ff ff ff ff ff ff ff ff ff
                 * maximum A-MSDU length
                 * supported channel width
                 * short GI for 40 MHz
                 * max A-MPDU length exponent
                 * min MPDU start spacing
        Device supports VHT-IBSS.
config wifi-device 'radio1'
        option type 'mac80211'
        option channel '36'
        option hwmode '11a'
        option path 'pci0000:00/0000:00:00.0/0000:01:00.0'
        option htmode 'VHT80'
        option disabled '0'
        option country 'PL'

config wifi-iface 'default_radio1'
        option device 'radio1'
        option network 'lan'
        option mode 'ap'
        option ssid 'Netgear_R6220'
        option encryption 'psk2'
Netgear R6220 + HUAWEI E3372 Hilink

34

Odp: Netgear R6220 instalacje OpenWrt

Ponawiam prośbę, za "stratę czasu" się jakoś odwdzięczę. smile

secam7 napisał/a:

Niestety to znalazłem już po moich eksperymentach z powiększaniem ubi:
https://forum.openwrt.org/t/netgear-r62 … tion/10889

Dlatego zrobiłem sobie tylko kopię z oryginalnego softu partycji "Factory",
no i obecnie ani na oryginalnym sofcie, ani na openwrt nie mam prawidłowych/oryginalnych mac .
Może ktoś ma dostęp do takiego Netgear R6220 i skopiuje dla mnie z firmowego softu:

mtd10: 00100000 00020000 "Factory"
mtd11: 00100000 00020000 "SC Private Data"
mtd15: 00200000 00020000 "SC Nvram"

Pomożecie??

Dzięki temu spróbuję jakoś skleić coś pasującego do mojego egzemplarza.

35

Odp: Netgear R6220 instalacje OpenWrt

Podłaczę się pod temat, gdyż nie chciałbym nowego nabytku od razu uwalić.
Który plik wrzucić na pena:
...-initramfs-kernel.bin
...-squashfs-kernel.bin   ???
Czym one się różnią?

36

Odp: Netgear R6220 instalacje OpenWrt

nesus napisał/a:

Podłaczę się pod temat, gdyż nie chciałbym nowego nabytku od razu uwalić.
Który plik wrzucić na pena:
...-initramfs-kernel.bin
...-squashfs-kernel.bin   ???
Czym one się różnią?

Hmm, a przeczytałeś ten wątek od początku? https://eko.one.pl/forum/viewtopic.php? … 99#p218799

GUI jest przereklamowane

ASUS WL-500gP v2, TP-Link TL-MR3420 v2, TP-Link TL-WR1043ND v3, TP-Link TL-WDR4300 v1, D-Link DWR-921 C3,
Netgear R6220

37

Odp: Netgear R6220 instalacje OpenWrt

Gr4nd0 napisał/a:
nesus napisał/a:

Podłaczę się pod temat, gdyż nie chciałbym nowego nabytku od razu uwalić.
Który plik wrzucić na pena:
...-initramfs-kernel.bin
...-squashfs-kernel.bin   ???
Czym one się różnią?

Hmm, a przeczytałeś ten wątek od początku? https://eko.one.pl/forum/viewtopic.php? … 99#p218799

Czytać czytałem ale chyba nie do końca zrozumiałem smile (nigdy nie wgrywałem w ten sposób oprogramowania)
Mam rozumieć, że muszę wrzucić wszystkie pliki ...krenel.bin ?

38

Odp: Netgear R6220 instalacje OpenWrt

Jakie wszystkie, tylko ten squashfs-kernel.bin. No i rootfs, jak instalować masz tutaj: https://github.com/openwrt/openwrt/comm … 9cfc8cf267

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

39

Odp: Netgear R6220 instalacje OpenWrt

Cezary napisał/a:

Jakie wszystkie, tylko ten squashfs-kernel.bin. No i rootfs, jak instalować masz tutaj: https://github.com/openwrt/openwrt/comm … 9cfc8cf267

Trochę zamieszania z tymi plikami "kernel" ale reszta już poszła gładko.
Dzięki za pomoc.

40

Odp: Netgear R6220 instalacje OpenWrt

Niestety szczęście przedwczesne.
Gargoyle się zgłosiło, zmieniłem hasło, wyłączyłem wifi, zatrzymałem router komendą halt i ....
już się nie podnosi, wpada w ciągły restart. Nie mogę wprowadzić go w failsafe.
Podpowiedzcie co jeszcze mogę zrobić by go postawić na nogi.

41

Odp: Netgear R6220 instalacje OpenWrt

nmrpflash can be used to recover to the netgear firmware if a broken
image was flashed.

Wgraj po prostu soft jeszcze raz.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

42

Odp: Netgear R6220 instalacje OpenWrt

ale jak, jak on się ciągle resetuje?

43

Odp: Netgear R6220 instalacje OpenWrt

Czytałeś instrukcję? https://github.com/jclehner/nmrpflash

Uruchom program i włącz netgeara do prądu. Samo się znajdzie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

44

Odp: Netgear R6220 instalacje OpenWrt

Jak go reanimujesz to wrzuć pliki dla @secam7

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

45

Odp: Netgear R6220 instalacje OpenWrt

Nikt nie mówił, że będzie łatwo.... wink

Który obraz próbować wrzucić? Oryginalny Netgara czy Gargoyle?


Cezary napisał/a:

Jak go reanimujesz to wrzuć pliki dla @secam7

tego nie rozumiem... możesz wyjaśnić

46

Odp: Netgear R6220 instalacje OpenWrt

Najpierw go reanimuj potem dostaniesz instrukcję co i jak.

Oryginalny netgeara.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

47

Odp: Netgear R6220 instalacje OpenWrt

Ciągle pod górę...

Ustaliłem na sztywno adres kart sieciowej w kompie.
Zainstalowałem Npcap w trybie kompatybilności WinPcap (bo mam Win10), wpisywałem komendy:

c:\netgar>nmrpflash -L
net0   0.0.0.0          b2:35:9f:xx:xx:xx  (Po│╣czenie lokalne* 2)
net3   0.0.0.0          b0:35:9f:xx:xx:xx  (Po│╣czenie lokalne* 1)
net5   192.168.1.2      80:fa:xx:xx:xx:xx  (Ethernet)
net6   192.168.2.13     b0:35:xx:xx:xx:xx  (Wi-Fi)

c:\netgar>nmrpflash.exe -i net5 -f R6220-V1.1.0.86.img
Failed to bind after 5 seconds: bind: »╣dany adres jest nieprawid│owy w tym kontekťcie.

c:\netgar>nmrpflash -i net5 -a 192.168.1.1 -f R6220-V1.1.0.86.img -c 'ifconfig eth0 192.168.1.2'
Advertising NMRP server on net5 ... /
No response after 60 seconds. Bailing out.

*xx:xx:xx moje wpisy

i mojego przypadku instrukcja nie przewiduje.
Co mogę dalej zrobić?

48

Odp: Netgear R6220 instalacje OpenWrt

"No response after 60 seconds. Bailing out."
The router did not respond. Try rebooting the device and run nmrpflash again. You could also try running nmrpflash with -m and specify your router's MAC address. It's also possible that your device does not support the NMRP protocol.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

49

Odp: Netgear R6220 instalacje OpenWrt

OK, udało się. Przywróciłem firmware producenta.
Cały problem to w odpowiednim momencie włączyć router do przywracania.

Co dalej?

Cezary napisał/a:

Najpierw go reanimuj potem dostaniesz instrukcję co i jak.

Oryginalny netgeara.

O co chodzi z tymi "plikami dla @secam7"?

50

Odp: Netgear R6220 instalacje OpenWrt

secam7 napisał/a:

Ponawiam prośbę, za "stratę czasu" się jakoś odwdzięczę. smile

secam7 napisał/a:

Niestety to znalazłem już po moich eksperymentach z powiększaniem ubi:
https://forum.openwrt.org/t/netgear-r62 … tion/10889

Dlatego zrobiłem sobie tylko kopię z oryginalnego softu partycji "Factory",
no i obecnie ani na oryginalnym sofcie, ani na openwrt nie mam prawidłowych/oryginalnych mac .
Może ktoś ma dostęp do takiego Netgear R6220 i skopiuje dla mnie z firmowego softu:

mtd10: 00100000 00020000 "Factory"
mtd11: 00100000 00020000 "SC Private Data"
mtd15: 00200000 00020000 "SC Nvram"

Pomożecie??

Dzięki temu spróbuję jakoś skleić coś pasującego do mojego egzemplarza.

Trzymaj https://drive.google.com/file/d/1iB9VXq … sp=sharing