Odp: Brak 'rootfs_data' po instalacji OpenWRT z poziomu Breed`a.
@stell_rat, a dlaczego, jeśli uda mi się skonfigurować VLAN`y i wpiąć je konkretnie w któregoś LAN`a to raczej nie powinno być z tym problemu - tak to widzę na chwilę obecną.
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Oprogramowanie / Software → Brak 'rootfs_data' po instalacji OpenWRT z poziomu Breed`a.
Strony Poprzednia 1 2 3 4
Zaloguj się lub zarejestruj by napisać odpowiedź
@stell_rat, a dlaczego, jeśli uda mi się skonfigurować VLAN`y i wpiąć je konkretnie w któregoś LAN`a to raczej nie powinno być z tym problemu - tak to widzę na chwilę obecną.
Cóż ja nie mam Orange. Po prostu mnie zastanawia czy może być na LAN dwa VLAN nie tagowane zmostkowane z WAN. Bo jak tam napisali będzie działać albo TV albo VOD na raz. Ale próbuj pewnie się uda. Pozostaje też nadanie priorytetów do VLAN'u.
@Cezary, czemu nie idzie zainstalować z opkg igmpproxy?
root@OpenWrt:/etc# opkg install igmpproxy
Unknown package 'igmpproxy'.
Collected errors:
* opkg_install_cmd: Cannot install package igmpproxy.
a dałeś wcześniej "opkg update"?
Ups
Faktycznie, dzięki!
Próbuje odpalić teraz TV na bazie tej konfiguracji - https://lafibre.info/remplacer-livebox/ … -fibre-tv/ z pewnymi zmianami jakie tutaj opisano https://trzepak.pl/viewtopic.php?f=20&a … 25#p473007 ale niestety coś nie gra
root@OpenWrt:~# /etc/rc.prio_vlan.sh
+ ip link set eth0.35 type vlan egress 0:0
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.838 type vlan egress 0:4
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.839 type vlan egress 0:5
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.35 type vlan egress 1:1
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.838 type vlan egress 1:4
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.839 type vlan egress 1:5
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.35 type vlan egress 2:2
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.838 type vlan egress 2:4
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.839 type vlan egress 2:5
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.35 type vlan egress 3:3
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.838 type vlan egress 3:4
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.839 type vlan egress 3:5
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.35 type vlan egress 4:4
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.838 type vlan egress 4:4
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.839 type vlan egress 4:5
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.35 type vlan egress 5:5
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.838 type vlan egress 5:4
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.839 type vlan egress 5:5
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.35 type vlan egress 6:6
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.838 type vlan egress 6:4
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.839 type vlan egress 6:5
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.35 type vlan egress 7:7
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.838 type vlan egress 7:4
ip: either "dev" is duplicate, or "type" is garbage
+ ip link set eth0.839 type vlan egress 7:5
ip: either "dev" is duplicate, or "type" is garbage
Tak wygląda plik:
root@OpenWrt:~# cat /etc/rc.prio_vlan.sh
#!/bin/sh
set -x
for i in 0 1 2 3 4 5 6 7 ; do
ip link set eth0.35 type vlan egress $i:$i >/dev/null
ip link set eth0.838 type vlan egress $i:4 >/dev/null
ip link set eth0.839 type vlan egress $i:5 >/dev/null
done
VLAN`y są ustawione:
root@OpenWrt:~# swconfig dev switch0 vlan 839 show
VLAN 839:
vid: 0
ports: 3t 6t
root@OpenWrt:~# swconfig dev switch0 vlan 838 show
VLAN 838:
vid: 0
ports: 3t 6t
@EDIT:
Udało mi się prawidłowo odpalić /etc/rc.prio_vlan.sh - potrzeba bylo zainstalować ip-full
Niestety przy odpaleniu kolejnego skryptu tj. /etc/rc.dhclient_tv.sh
root@OpenWrt:~# cat /etc/rc.dhclient_tv.sh
dhclient -v -sf /usr/sbin/dhclient-script br-TV
Dekoder nie może uzyskać IP.
root@OpenWrt:~# /etc/rc.dhclient_tv.sh
Internet Systems Consortium DHCP Client 4.3.6
Copyright 2004-2017 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
can't create /var/db/dhclient.leases: No such file or directory
Listening on LPF/br-TV/34:ce:00:6a:7b:dd
Sending on LPF/br-TV/34:ce:00:6a:7b:dd
Sending on Socket/fallback
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 4
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 16
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 8
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 10
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
rm: can't remove '/etc/resolv.conf.dhclient': No such file or directory
cat: can't open '/etc/resolv.conf.*': No such file or directory
mkdir -p /var/db ?
Nic nie zmienia, tworzy jedynie pusty plik.
Nie rozumiem tylko czemu w przypadku logu osoby z Francji ma ona coś takiego:
root @ GL-MT300N: / etc # /etc/rc.dhclient_tv.sh
Internet Systems Consortium DHCP Client 4.2.4
Copyright 2004-2012 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF / br-tv / e4: 95: 6e: 40: 7a: 63
Sending on LPF / br-tv / e4: 95: 6e: 40: 7a: 63
Sending on Socket / fallback
[b]DHCPREQUEST[/b] on br-tv to 255.255.255.255 port 67
DHCPACK from 10.93.124.254
/ usr / sbin / dhclient-script: line 134: hostname: not found
/ usr / sbin / dhclient-script: line 134: hostname: not found
cat: can not open '/etc/resolv.conf.*': No such file or directory
bound to 10.93.124.135 - renewal in 43157 seconds.
A u mnie jest to:
root@OpenWrt:/tmp/db# /etc/rc.dhclient_tv.sh
Internet Systems Consortium DHCP Client 4.3.6
Copyright 2004-2017 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Listening on LPF/br-TV/34:ce:00:6a:7b:dd
Sending on LPF/br-TV/34:ce:00:6a:7b:dd
Sending on Socket/fallback
[b]DHCPDISCOVER[/b] on br-TV to 255.255.255.255 port 67 interval 6
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 12
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 5
No DHCPOFFERS received.
No working leases in persistent database - sleeping.
rm: can't remove '/etc/resolv.conf.dhclient': No such file or directory
cat: can't open '/etc/resolv.conf.*': No such file or directory
DHCPREQUEST a DHCPDISCOVER, kwestia innej wersji klienta DHCP?
Po prostu nie dostałeś adresu.
No więc wygląda na to że ten router chyba nie potrafi zrobić tego co potrzebuje.
W przypadku ustawienia VLANów w ten sposób:
config switch_vlan
option device 'switch0'
option vlan '35'
option vid '35'
option ports '1t 6t'
config switch_vlan
option device 'switch0'
option vlan '838'
option vid '838'
option ports '6t'
config switch_vlan
option device 'switch0'
option vlan '839'
option vid '839'
option ports '6t'
Internet działa, ale po wykonaniu komendy /etc/rc.dhclient_tv.sh aby dekoder dostał IP, nadal jest go brak.
Przy poniższym ustawieniu VLANów
config switch_vlan
option device 'switch0'
option vlan '35'
option vid '35'
option ports '1t 6t'
config switch_vlan
option device 'switch0'
option vlan '838'
option vid '838'
option ports '1t 6t'
config switch_vlan
option device 'switch0'
option vlan '839'
option vid '839'
option ports '1t 6t'
Dekoder dostaje "niby" IP ale niestety wtedy nie działa w ogóle internet, ani na telewizorze nie widać aby dekoder połączył się z routerem.
Cezary, czy to oznacza że nie uda się tego uruchomić na tym konkretnym routerze?
@EDIT:
Wygląda na to że po wykonaniu:
root@OpenWrt:~# /etc/rc.dhclient_tv.sh
Internet Systems Consortium DHCP Client 4.3.6
Copyright 2004-2017 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
can't create /var/db/dhclient.leases: No such file or directory
Listening on LPF/br-TV/34:ce:00:6a:7b:dd
Sending on LPF/br-TV/34:ce:00:6a:7b:dd
Sending on Socket/fallback
DHCPDISCOVER on br-TV to 255.255.255.255 port 67 interval 7
DHCPREQUEST on br-TV to 255.255.255.255 port 67
DHCPOFFER from 10.243.0.2
DHCPACK from 10.243.0.2
/usr/sbin/dhclient-script: line 134: hostname: not found
/usr/sbin/dhclient-script: line 134: hostname: not found
can't create /var/db/dhclient.leases: No such file or directory
bound to 10.243.4.125 -- renewal in 34213 seconds.
Internet "pada", ale jeśli raz jeszcze wybiorę "połącz" na interfejsie WAN to ponownie zaczyna działać.
Dziwne jest to że nawet po odpaleniu " /etc/rc.dhclient_tv.sh" i następnie "ifstatus TV" to nie widać aby jakiekolwiek dane w tym interfejsie się uzupełniały (jest pusto, tj. brak IP)
Więc może to problem z samą obsługą switcha. Nie wiem, nie mam dostępu do takiej usługi wiec nie sprawdzę.
Hmm czemu w takim razie ifconfig, pokazuje takie coś:
br-TV Link encap:Ethernet HWaddr 34:CE:00:6A:7B:DD
inet addr:10.243.4.125 Bcast:10.243.15.255 Mask:255.255.240.0
inet6 addr: fe80::36ce:ff:fe6a:7bdd/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:440 errors:0 dropped:0 overruns:0 frame:0
TX packets:819 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:25420 (24.8 KiB) TX bytes:64394 (62.8 KiB)
Mam rozumieć że to jest raczej kwestia tylko konfiguracji, a nie samego "routera" jako tako?
To co pokazałeś to tylko interfejs. A chodzi o to że switch może nie przepuszczać tagowanych ramek lub trzeba coś zrobić że przepuszczał.
Da się to w jakiś sposób "przefiltrować" lub "zobaczyć" czy/gdzie się to blokuje?
Jedna z możliwości to snifowanie ruchu np. wiresharkiem. Jak wiesz jak leci transmisja to możesz wywnioskować czego brakuje i który element to powoduje.
Aha, czyli można go w takim razie sprzedawać.
Bo to już raczej nie na moje możliwości.
@EDIT:
Ja to widzę tak, że interfejs faktycznie jest stworzony....tylko teraz w jaki sposób on powinien się wpiąć na 2 port LAN gdzie jest wpięty kabel od dekodera.
Zakładając że wydobyłeś LAN2 jako osobny interfejs to dodaj go do bridge br-TV.
No właśnie tego do końca nie rozumiem, bo w którymkolwiek tutorialu bym nie czytał nie widziałem opcji aby miał coś "grupować" i nie do końca wiem jak mam LAN2 oddzielnie wydzielić.
Bo rozumiem że eth0.1 jest jako całość LAN`u?
Coś musi być namieszane ostro bo podłączając pod LAN konsolę PS4 w ogóle nie chce dostać adresu z DHCP, laptop po WLAN działa poprawnie.
Proooszę: http://eko.one.pl/?p=openwrt-vlan#wydzielenieportu
br-lan to lan. A on się składa z eth0.1 (zwykle) + wlan0 (zwykle).
No więc tak, udało się odpalić aktualnie samo TV (bez VOD etc) tym sposobem - https://trzepak.pl/viewtopic.php?f=20&a … 77#p432124
Teraz pytanko, czy jest możliwe aby przenieść się z połączenia po RJ45 na WLAN?
Teraz mam tak:
......
config switch_vlan
option device 'switch0'
option vlan '100'
option vid '100'
option ports '3 6t'
.......
config switch_vlan
option device 'switch0'
option vlan '838'
option vid '838'
option ports '1t 6t'
config switch_vlan
option device 'switch0'
option vlan '839'
option vid '839'
option ports '1t 6t'
config interface 'tv'
option type 'bridge'
option proto 'none'
option ifname 'eth0.100 eth0.838 eth0.839'
Mogę utworzyć VLAN`a do WiFi?
Podając np. wlan0.839 automatycznie zrobi się vlan na wifi. Ale musisz go zrobić po tym jak uruchomi się wifi, bo wcześniej nie ma jeszcze interfejsu. Czy zadziała u ciebie - sprawdź.
Miałem na routerze TP-Link Archer C7 V4 EU identyczny problem z VLANem 35 co ty, dzięki waszym sugestiom go rozwiązałem.
Dziękuję!
Kurde na jakim speedteście bym nie puścił to max do 300 i więcej nie idzie.
u ciebie idzie max 300 bo masz umowę na 600.
Ja mam umowę na 300 i u mnie teraz idzie max 150 - 240 (właśnie sprawdzałem). Robisz speedtest w czasie gdzy TP daje ci należne ci pasmo. Czyli jedną trzecią tego za co płacisz, ale zwykle z 90% prędkości maksymalnej.
Opisane to jest tu https://nasz.orange.pl/t5/Internet-domo … td-p/15020
Przeczytałem w swojej umowie na 300/30 podpisanej w zeszłym tygodniu. GWARANTUJĄ mi minimalną prędkość 100/10.
Strony Poprzednia 1 2 3 4
Zaloguj się lub zarejestruj by napisać odpowiedź
eko.one.pl → Oprogramowanie / Software → Brak 'rootfs_data' po instalacji OpenWRT z poziomu Breed`a.
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc