[ 0.000000] Linux version 4.1.20 (cezary@samsung) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 unknown) ) #3 Tue May 3 11:26:28 UTC 2016
[ 0.000000] MyLoader: sysp=1d077ffa, boardp=e14ac615, parts=09838996
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 803cbe20, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR841N-v9 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60428K/65536K available (2784K kernel code, 141K rwdata, 684K rodata, 284K init, 195K bss, 5108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Clocks: CPU:650.000MHz, DDR:392.016MHz, AHB:216.666MHz, Ref:25.000MHz
[ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns
[ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns
[ 0.008237] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[ 0.071105] pid_max: default: 32768 minimum: 301
[ 0.076113] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.083091] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.093877] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.104969] NET: Registered protocol family 16
[ 0.111175] MIPS: machine is TP-LINK TL-WR841N/ND v9
[ 0.569696] Switched to clocksource MIPS
[ 0.575285] NET: Registered protocol family 2
[ 0.580986] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.588357] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.595144] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.601978] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.608158] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.615184] NET: Registered protocol family 1
[ 0.619925] PCI: CLS 0 bytes, default 32
[ 0.621084] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.646126] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.652373] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.665850] io scheduler noop registered
[ 0.670064] io scheduler deadline registered (default)
[ 0.675723] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.682963] console [ttyS0] disabled
[ 0.706883] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.715992] console [ttyS0] enabled
[ 0.723551] bootconsole [early0] disabled
[ 0.735398] m25p80 spi0.0: found gd25q128, expected m25p80
[ 0.741172] m25p80 spi0.0: gd25q128 (16384 Kbytes)
[ 0.747276] 5 tp-link partitions found on MTD device spi0.0
[ 0.753104] Creating 5 MTD partitions on "spi0.0":
[ 0.758063] 0x000000000000-0x000000020000 : "u-boot"
[ 0.764198] 0x000000020000-0x000000150cd8 : "kernel"
[ 0.770269] 0x000000150cd8-0x000000ff0000 : "rootfs"
[ 0.776241] mtd: device 2 (rootfs) set to be root filesystem
[ 0.782219] 1 squashfs-split partitions found on MTD device rootfs
[ 0.788608] 0x000000330000-0x000000ff0000 : "rootfs_data"
[ 0.795100] 0x000000ff0000-0x000001000000 : "art"
[ 0.800887] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.831780] libphy: ag71xx_mdio: probed
[ 1.422271] ag71xx-mdio.1: Found an AR934X built-in switch
[ 1.465600] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.062659] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 2.072885] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.081741] NET: Registered protocol family 10
[ 2.091149] NET: Registered protocol family 17
[ 2.095843] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.109091] 8021q: 802.1Q VLAN Support v1.8
[ 2.121443] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.131147] Freeing unused kernel memory: 284K (803e9000 - 80430000)
[ 3.058619] init: Console is alive
[ 3.062630] init: - watchdog -
[ 3.977667] usbcore: registered new interface driver usbfs
[ 3.983520] usbcore: registered new interface driver hub
[ 3.989107] usbcore: registered new device driver usb
[ 4.000863] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.009367] ehci-platform: EHCI generic platform driver
[ 4.018211] init: - preinit -
[ 4.658145] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.687193] random: procd urandom read with 7 bits of entropy available
[ 6.252178] eth0: link up (1000Mbps/Full duplex)
[ 6.256993] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 7.891405] jffs2: notice: (357) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 7.909199] mount_root: switching to jffs2 overlay
[ 7.945489] eth0: link down
[ 7.961498] procd: - early -
[ 7.964616] procd: - watchdog -
[ 8.593011] procd: - ubus -
[ 8.648981] procd: - init -
[ 9.498235] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.520479] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 9.528128] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 9.539153] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.556948] nf_conntrack version 0.5.0 (948 buckets, 3792 max)
[ 9.604267] xt_time: kernel timezone is -0000
[ 9.680296] PPP generic driver version 2.4.2
[ 9.687749] NET: Registered protocol family 24
[ 9.749544] ath: EEPROM regdomain: 0x0
[ 9.749571] ath: EEPROM indicates default country code should be used
[ 9.749580] ath: doing EEPROM country->regdmn map search
[ 9.749602] ath: country maps to regdmn code: 0x3a
[ 9.749613] ath: Country alpha2 being used: US
[ 9.749621] ath: Regpair used: 0x3a
[ 9.761496] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 9.765796] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
[ 17.037897] device eth0 entered promiscuous mode
[ 17.067780] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 17.110352] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 18.652281] eth0: link up (1000Mbps/Full duplex)
[ 18.657123] br-lan: port 1(eth0) entered forwarding state
[ 18.662783] br-lan: port 1(eth0) entered forwarding state
[ 18.726261] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 18.732750] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 18.766059] device wlan0 entered promiscuous mode
[ 18.771430] br-lan: port 2(wlan0) entered forwarding state
[ 18.777124] br-lan: port 2(wlan0) entered forwarding state
[ 18.844435] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 20.659735] br-lan: port 1(eth0) entered forwarding state
[ 20.769733] br-lan: port 2(wlan0) entered forwarding state
Dioda power jest zapalona cały czas.
dioda wifi działa jako SYS
dioda LAN 2 jako wifi
dioda USB jako port lan1
dioda wan zielony jako port lan 4
dioda wan pomarańczowy jako port wan
dioda lan4 jako port lan 2
dioda lan3 jako port lan 3 - OK
Portu USB nie mogę sprawdzić bo pakiety z repo nie pasują.
Konfiguracja w system wygląda OK:
root@OpenWrt:~# cat /etc/config/system
config system
option hostname 'OpenWrt'
option timezone 'UTC'
config timeserver 'ntp'
list server '0.openwrt.pool.ntp.org'
list server '1.openwrt.pool.ntp.org'
list server '2.openwrt.pool.ntp.org'
list server '3.openwrt.pool.ntp.org'
option enabled '1'
option enable_server '0'
config led 'led_wan'
option name 'WAN'
option sysfs 'tp-link:green:wan'
option trigger 'netdev'
option mode 'link tx rx'
option dev 'eth1'
config led 'led_lan1'
option name 'LAN1'
option sysfs 'tp-link:green:lan1'
option trigger 'switch0'
option port_mask '0x10'
config led 'led_lan2'
option name 'LAN2'
option sysfs 'tp-link:green:lan2'
option trigger 'switch0'
option port_mask '0x08'
config led 'led_lan3'
option name 'LAN3'
option sysfs 'tp-link:green:lan3'
option trigger 'switch0'
option port_mask '0x04'
config led 'led_lan4'
option name 'LAN4'
option sysfs 'tp-link:green:lan4'
option trigger 'switch0'
option port_mask '0x02'
config led 'led_wlan'
option name 'WLAN'
option sysfs 'tp-link:green:wlan'
option trigger 'phy0tpt'
https://tplinkforum.pl - Polskie forum poświęcone tematyce urządzeń firmy TP-Link i Neffos
