1 Temat przez sehack

(1 odpowiedzi, napisanych Oprogramowanie / Software)

Witajcie, podobno nie ma głupich pytań, a że postanowiłem jutro to ogarnąć postaniwię opisać moje wyzwanie i oczekuję od mądrzejszych i doświadczonych na naprowadzenie.

Są dwa modemy LTE USB, (załóżmy że już działają: konfiguracja, sterowniki) w nich karty SIM różnych operatorów.
Na karcie SIM1 (dostępne 10GB i oprócz tego nk bez limitu transferu) - ma dzialać nasza-klasa.pl
Na karcie SIM2 (dostępne 50GB i oprócz tego nielimitowany transfer dla wrzuta.pl)

Modemy te wpięte w malinkę i udostępniają internet jako jedno połączenie po lanie albo wifi (szczegół).
Wchodząc na stronę wrzuta.pl ruch jest kierowany do modemu z SIM2, a na naszą-klasę do modemu z SIM1. Reszta ruchu nieuwzględniona będzie kierowana losowo.

Czy macie pomysł jak to logicznie zrobić bez wywarzania otwartych drzwi? Nie chcę od was gotowca, ale naprowadzenie.

Idź do forum: Oprogramowanie / Software

2 Odpowiedź przez sehack

(74 odpowiedzi, napisanych Oprogramowanie / Software)

Udało się skompilować, obraz posiada wbudowane narzędzia do pentestu Luci,WiFi, sterowniki mt72xx i dla atherosa może komuś się przyda. Wystarczy rozpakować i wrzucić obraz za pomocą np. Win32 Disk Imager na kartę pamięci SD.

http://zatechnologia.pl/download/openwrt/openwrt-brcm2708-bcm2708-rpi-ext4-factory.7z

Dziękuję wszystkim, temat do zamknięcia.

Idź do forum: Oprogramowanie / Software

3 Odpowiedź przez sehack

(74 odpowiedzi, napisanych Oprogramowanie / Software)

Pierwsza kompilacja za mną system ruszył, ale mam problem robię wszystko wg. zaleceń https://github.com/cyangy/openwrt-mt7612u

overwrite the package/kernel/mt76 with this repository's files and run

$ make menuconfig

to select the kernel module

Kernel modules --> Wireless Drivers--> kmod-mt76x2u

Nie mam takiego modułu kmod-mt76x2u w tej lokacji, jest tylko kmod-mt7601u. Więc już na starcie jest problem, po skompilowaniu z tamtym modułem jest niestety ta sama sytuacja co była na początku, czyli brak sterownika.

Idź do forum: Oprogramowanie / Software

4 Odpowiedź przez sehack

(74 odpowiedzi, napisanych Oprogramowanie / Software)

Ok, czyli muszę skompilować całego lede pod malinkę. Tu znalazłem sterownik https://github.com/cyangy/openwrt-mt7612u będę walczył. Dzięki cezary, przynajmniej nie owijasz w bawełnę. Tematu jeszcze nie warto zamykać, bo poinformuję co z tego wyszło.

Idź do forum: Oprogramowanie / Software

5 Odpowiedź przez sehack

(74 odpowiedzi, napisanych Oprogramowanie / Software)

Zainstalowałem, niestety dalej nie wykrywa

C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=200mA
I:* If#= 0 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

Idź do forum: Oprogramowanie / Software

6 Temat przez sehack

(74 odpowiedzi, napisanych Oprogramowanie / Software)

Witajcie, to znowu ja z tym samym problemem co zawsze tylko z inną kartą, czyli nie mogę uruchomić karty WiFi Netgear A6210 (MT7612U).

Zainstalowane pakiety:

base-files - 194.2-r7676-cddd7b4c77
brcm2708-gpu-fw - 2018-11-29-b428bdd819df8d0ad3009b64492a4b3d1f9453e4
brcmfmac-firmware-43430-sdio - 2017-09-06-a61ac5cf-1
brcmfmac-firmware-usb - 2017-09-06-a61ac5cf-1
busybox - 1.28.4-2
dnsmasq - 2.80-1.2
dropbear - 2017.75-7.1
e2fsprogs - 1.44.1-1
firewall - 2018-08-13-1c4d5bcd-1
fstools - 2018-12-28-af93f4b8-3
fwtool - 1
hostapd-common - 2018-05-21-62566bc2-5
ip6tables - 1.6.2-1
iptables - 1.6.2-1
iw - 4.14-1
iwinfo - 2018-07-31-65b8333f-1
jshn - 2018-07-25-c83a84af-2
jsonfilter - 2018-02-04-c7e938d6-1
kernel - 4.9.152-1-419a2ca10fc2faa1e06aec8546b4c2e7
kmod-brcmfmac - 4.9.152+2017-11-01-9
kmod-brcmutil - 4.9.152+2017-11-01-9
kmod-cfg80211 - 4.9.152+2017-11-01-9
kmod-fs-vfat - 4.9.152-1
kmod-hid - 4.9.152-1
kmod-hid-generic - 4.9.152-1
kmod-input-core - 4.9.152-1
kmod-input-evdev - 4.9.152-1
kmod-ip6tables - 4.9.152-1
kmod-ipt-conntrack - 4.9.152-1
kmod-ipt-core - 4.9.152-1
kmod-ipt-nat - 4.9.152-1
kmod-lib-crc-ccitt - 4.9.152-1
kmod-mac80211 - 4.9.152+2017-11-01-9
kmod-mmc - 4.9.152-1
kmod-mt76-core - 4.9.152+2019-01-25-0b939dc7-1
kmod-mt76-usb - 4.9.152+2019-01-25-0b939dc7-1
kmod-mt76x0-common - 4.9.152+2019-01-25-0b939dc7-1
kmod-mt76x02-common - 4.9.152+2019-01-25-0b939dc7-1
kmod-mt76x02-usb - 4.9.152+2019-01-25-0b939dc7-1
kmod-mt76x0u - 4.9.152+2019-01-25-0b939dc7-1
kmod-mt76x2-common - 4.9.152+2019-01-25-0b939dc7-1
kmod-nf-conntrack - 4.9.152-1
kmod-nf-conntrack6 - 4.9.152-1
kmod-nf-ipt - 4.9.152-1
kmod-nf-ipt6 - 4.9.152-1
kmod-nf-nat - 4.9.152-1
kmod-nf-reject - 4.9.152-1
kmod-nf-reject6 - 4.9.152-1
kmod-nls-base - 4.9.152-1
kmod-nls-cp437 - 4.9.152-1
kmod-nls-iso8859-1 - 4.9.152-1
kmod-nls-utf8 - 4.9.152-1
kmod-ppp - 4.9.152-1
kmod-pppoe - 4.9.152-1
kmod-pppox - 4.9.152-1
kmod-slhc - 4.9.152-1
kmod-sound-arm-bcm2835 - 4.9.152-1
kmod-sound-core - 4.9.152-1
kmod-usb-core - 4.9.152-1
kmod-usb-hid - 4.9.152-1
libblkid - 2.32-2
libblobmsg-json - 2018-07-25-c83a84af-2
libc - 1.1.19-1
libcomerr - 1.44.1-1
libext2fs - 1.44.1-1
libf2fs - 1.10.0-1
libgcc - 7.3.0-1
libip4tc - 1.6.2-1
libip6tc - 1.6.2-1
libiwinfo - 2018-07-31-65b8333f-1
libiwinfo-lua - 2018-07-31-65b8333f-1
libjson-c - 0.12.1-2
libjson-script - 2018-07-25-c83a84af-2
liblua - 5.1.5-1
liblucihttp - 2018-05-18-cb119ded-1
liblucihttp-lua - 2018-05-18-cb119ded-1
libnl-tiny - 0.1-5
libpthread - 1.1.19-1
librt - 1.1.19-1
libsmartcols - 2.32-2
libss - 1.44.1-1
libubox - 2018-07-25-c83a84af-2
libubus - 2018-10-06-221ce7e7-1
libubus-lua - 2018-10-06-221ce7e7-1
libuci - 2018-08-11-4c8b4d6e-1
libuclient - 2018-11-24-3ba74ebc-1
libuuid - 2.32-2
libxtables - 1.6.2-1
logd - 2018-02-14-128bc35f-2
lua - 5.1.5-1
luci - git-19.020.41695-6f6641d-1
luci-app-firewall - git-19.020.41695-6f6641d-1
luci-base - git-19.020.41695-6f6641d-1
luci-lib-ip - git-19.020.41695-6f6641d-1
luci-lib-jsonc - git-19.020.41695-6f6641d-1
luci-lib-nixio - git-19.020.41695-6f6641d-1
luci-mod-admin-full - git-19.020.41695-6f6641d-1
luci-proto-ipv6 - git-19.020.41695-6f6641d-1
luci-proto-ppp - git-19.020.41695-6f6641d-1
luci-theme-bootstrap - git-19.020.41695-6f6641d-1
mkf2fs - 1.10.0-1
mtd - 23
netifd - 2018-11-19-4b83102d-2
odhcp6c - 2018-07-14-67ae6a71-15
odhcpd-ipv6only - 1.15-3
openwrt-keyring - 2018-05-18-103a32e9-1
opkg - 2019-01-18-7708a01a-1
partx-utils - 2.32-2
ppp - 2.4.7-12
ppp-mod-pppoe - 2.4.7-12
procd - 2018-03-28-dfb68f85-1
rpcd - 2018-11-28-3aa81d0d-1
rpcd-mod-rrdns - 20170710
ubox - 2018-02-14-128bc35f-2
ubus - 2018-10-06-221ce7e7-1
ubusd - 2018-10-06-221ce7e7-1
uci - 2018-08-11-4c8b4d6e-1
uclient-fetch - 2018-11-24-3ba74ebc-1
uhttpd - 2018-11-28-cdfc902a-2
usign - 2015-07-04-ef641914-1
wireless-regdb - 2017-10-20-4343d359
wpad-mini - 2018-05-21-62566bc2-5

cat /sys/kernel/debug/usb/devices

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int= -3, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 4.09
S:  Manufacturer=Linux 4.9.152 dwc_otg_hcd
S:  Product=DWC OTG Controller
S:  SerialNumber=20980000.usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 5
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=02 MxPS=64 #Cfgs=  1
P:  Vendor=0424 ProdID=9514 Rev= 2.00
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  2mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=01 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=02 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0424 ProdID=ec00 Rev= 2.00
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  2mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=smsc95xx
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=  16 Ivl=1ms

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0846 ProdID=9053 Rev= 1.00
S:  Manufacturer=NETGEAR
S:  Product=A6210
S:  SerialNumber=100
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=200mA
I:* If#= 0 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Jedyne czego nie mogłem zainstalować to "kmod-mt7601u_4.9.152+2017-11-01-9_arm_arm1176jzf-s_vfp.ipk" bo wymaga MT7601-firmware którego nie mogę nigdzie znaleźć.

Idź do forum: Oprogramowanie / Software

7 Odpowiedź przez sehack

(5 odpowiedzi, napisanych Oprogramowanie / Software)

Walczyłem, aż ruszyło problem był z maską podsieci. Dzięki cezary, jak zawsze - pomogłeś. Pozdrawiam.

Idź do forum: Oprogramowanie / Software

8 Odpowiedź przez sehack

(5 odpowiedzi, napisanych Oprogramowanie / Software)

OK, karta jest wykrywana. Mam jeszcze jedno pytanie jak skonfigurować połączenie karta USB WiFi łączy się z siecią (w której trzeba na sztywno wbić statyczny IP) z której internet chciałbym udostępnić po lan?

Idź do forum: Oprogramowanie / Software

9 Temat przez sehack

(5 odpowiedzi, napisanych Oprogramowanie / Software)

Witam, nie mogę skonfigurować CC 15.05 na malince tak żeby wykrywało mi tą kartę wifi.
Co zrobiłem?
Zainstalowałem mac80211, KMOD-RT28xx_USB itd. pełna lista tutaj:

/dev$ opkg list
6in4 - 21-2
6rd - 9-2
6to4 - 12-2
base-files - 157-r46767
brcm2708-gpu-fw - 20150210-1
busybox - 1.23.2-1
dnsmasq - 2.73-1
dropbear - 2015.67-1
firewall - 2015-07-27
fstools - 2015-05-24-09027fc86babc3986027a0e677aca1b6999a9e14
hostapd - 2015-03-25-1
hostapd-common - 2015-03-25-1
ip6tables - 1.4.21-1
iptables - 1.4.21-1
iw - 3.17-1
jshn - 2015-06-14-d1c66ef1131d14f0ed197b368d03f71b964e45f8
jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9
kernel - 3.18.20-1-57d4b7d13c23edd1a689dd6d6adc65ad
kmod-cfg80211 - 3.18.20+2015-03-09-3
kmod-crypto-aes - 3.18.20-1
kmod-crypto-arc4 - 3.18.20-1
kmod-crypto-core - 3.18.20-1
kmod-hid - 3.18.20-1
kmod-hid-generic - 3.18.20-1
kmod-input-core - 3.18.20-1
kmod-input-evdev - 3.18.20-1
kmod-ip6tables - 3.18.20-1
kmod-ipt-conntrack - 3.18.20-1
kmod-ipt-core - 3.18.20-1
kmod-ipt-nat - 3.18.20-1
kmod-iptunnel - 3.18.20-1
kmod-iptunnel4 - 3.18.20-1
kmod-ipv6 - 3.18.20-1
kmod-lib-crc-ccitt - 3.18.20-1
kmod-lib-crc-itu-t - 3.18.20-1
kmod-libphy - 3.18.20-1
kmod-mac80211 - 3.18.20+2015-03-09-3
kmod-nf-conntrack - 3.18.20-1
kmod-nf-conntrack6 - 3.18.20-1
kmod-nf-ipt - 3.18.20-1
kmod-nf-ipt6 - 3.18.20-1
kmod-nf-nat - 3.18.20-1
kmod-nf-nathelper - 3.18.20-1
kmod-nls-base - 3.18.20-1
kmod-phy-broadcom - 3.18.20-1
kmod-ppp - 3.18.20-1
kmod-pppoe - 3.18.20-1
kmod-pppox - 3.18.20-1
kmod-rt2x00-lib - 3.18.20+2015-03-09-3
kmod-rt2x00-usb - 3.18.20+2015-03-09-3
kmod-sit - 3.18.20-1
kmod-slhc - 3.18.20-1
kmod-sound-arm-bcm2835 - 3.18.20-1
kmod-sound-core - 3.18.20-1
kmod-usb-core - 3.18.20-1
kmod-usb-hid - 3.18.20-1
kmod-usb-ohci - 3.18.20-1
kmod-usb2 - 3.18.20-1
kmod-usbmon - 3.18.20-1
libblobmsg-json - 2015-06-14-d1c66ef1131d14f0ed197b368d03f71b964e45f8
libc - 0.9.33.2-1
libgcc - 4.8-linaro-1
libip4tc - 1.4.21-1
libip6tc - 1.4.21-1
libiwinfo - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371
libiwinfo-lua - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371
libjson-c - 0.12-1
libjson-script - 2015-06-14-d1c66ef1131d14f0ed197b368d03f71b964e45f8
liblua - 5.1.5-1
libnl-tiny - 0.1-4
libubox - 2015-06-14-d1c66ef1131d14f0ed197b368d03f71b964e45f8
libubus - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
libubus-lua - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
libuci - 2015-04-09.1-1
libuci-lua - 2015-04-09.1-1
libxtables - 1.4.21-1
lua - 5.1.5-1
luci - git-15.245.46763-b179283-1
luci-app-firewall - git-15.245.46763-b179283-1
luci-base - git-15.245.46763-b179283-1
luci-lib-ip - git-15.245.46763-b179283-1
luci-lib-nixio - git-15.245.46763-b179283-1
luci-mod-admin-full - git-15.245.46763-b179283-1
luci-proto-ipv6 - git-15.245.46763-b179283-1
luci-proto-ppp - git-15.245.46763-b179283-1
luci-theme-bootstrap - git-15.245.46763-b179283-1
mtd - 21
netifd - 2015-06-08-8795f9ef89626cd658f615c78c6a17e990c0dcaa
odhcp6c - 2015-07-13-024525798c5f6aba3af9b2ef7b3af2f3c14f1db8
odhcpd - 2015-05-21-2ebf6c8216287983779c8ec6597d30893b914a7c
opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-7
ppp - 2.4.7-6
ppp-mod-pppoe - 2.4.7-6
procd - 2015-08-16-0da5bf2ff222d1a499172a6e09507388676b5a08
rpcd - 2015-05-17-3d655417ab44d93aad56a6d4a668daf24b127b84
ubox - 2015-07-14-907d046c8929fb74e5a3502a9498198695e62ad8
ubus - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
ubusd - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
uci - 2015-04-09.1-1
uhttpd - 2015-08-17-f91788b809d9726126e9cf4384fedbbb0c5b8a73
uhttpd-mod-ubus - 2015-08-17-f91788b809d9726126e9cf4384fedbbb0c5b8a73
usign - 2015-05-08-cf8dcdb8a4e874c77f3e9a8e9b643e8c17b19131
wpad - 2015-03-25-1

po wpisaniu /dev$ cat /sys/kernel/debug/usb/devices wykrywa to:

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=-10, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.18
S:  Manufacturer=Linux 3.18.20 dwc_otg_hcd
S:  Product=DWC OTG Controller
S:  SerialNumber=bcm2708_usb
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 5
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=02 MxPS=64 #Cfgs=  1
P:  Vendor=0424 ProdID=9514 Rev= 2.00
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  2mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=01 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=02 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0424 ProdID=ec00 Rev= 2.00
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  2mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=smsc95xx
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=  16 Ivl=1ms

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=02 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=148f ProdID=3070 Rev= 1.01
S:  Manufacturer=Ralink
S:  Product=802.11 n WLAN
S:  SerialNumber=1.0
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=450mA
I:* If#= 0 Alt= 0 #EPs= 7 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

lw list nic nie wyświetla tak samo jak i po poleceniu wifi detect > /etc/config/wireless konfiguracja jest pusta. Nie wiem co zrobić.

Idź do forum: Oprogramowanie / Software

10 Odpowiedź przez sehack

(6 odpowiedzi, napisanych Oprogramowanie / Software)

Chciałbym wykorzystać podatność mojego TP-Link wr740n i zaserwować mu binarke, którą uruchomi na prawach roota.

Idź do forum: Oprogramowanie / Software

11 Odpowiedź przez sehack

(6 odpowiedzi, napisanych Oprogramowanie / Software)

Szukałem i jedyne co znalazłem to https://github.com/darkerego/mips-binaries ale brakuje tam telnetu.

Idź do forum: Oprogramowanie / Software

12 Temat przez sehack

(6 odpowiedzi, napisanych Oprogramowanie / Software)

Witajcie, potrzebuję binarke telnetd pod architekturę MIPS.

Idź do forum: Oprogramowanie / Software

13 Temat przez sehack

(2 odpowiedzi, napisanych Oprogramowanie / Software)

Cześć, mam pytanie czy ktoś używał portu szeregowego wbudowanego w router (nie koniecznie wr740n) do komunikacji z arduino lub innym urządzeniem?
Jeżeli tak, to jak i co było potrzebne?
Pytanie dość głupie, chciałbym wykorzystać go do komunikacji z innym urządzeniem przez UART.

Idź do forum: Oprogramowanie / Software

14 Odpowiedź przez sehack

(2 odpowiedzi, napisanych Oprogramowanie / Software)

Dzięki Cezary że tutaj czuwasz, no nic, będę walczył.

Idź do forum: Oprogramowanie / Software

15 Temat przez sehack

(2 odpowiedzi, napisanych Oprogramowanie / Software)

Pobrałem Ubuntu 14.04, postawiłem na wirtualnej maszynie, po instalowałem paczki, próbuję skompilować obraz OpenWRT od producenta routera Asus RT-AC51U

make[5]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl/ssl'
if [ -n "libcrypto.so.1.0.0 libssl.so.1.0.0" ]; then \
        (cd ..; make libssl.so.1.0.0); \
    fi
make[6]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl'
[ -z "" ] || mipsel-uclibc-gcc -fPIC -DOPENSSL_PIC -DOPENSSL_THREADS -D_REENTRANT -DDSO_DLFCN -DHAVE_DLFCN_H -ffunction-sections -fdata-sections -DL_ENDIAN -DTERMIO -Os -DLINUX26 -DDEBUG_NOISY -DDEBUG_RCTEST -pipe -funit-at-a-time -Wno-pointer-sign -mtune=mips32 -mips32 -DLINUX30 -DLINUX_KERNEL_VERSION=132644 --sysroot=/opt/openwrt-gcc463.mips -DOPENSSL_SMALL_FOOTPRINT -fomit-frame-pointer -Wall -Iinclude \
        -DFINGERPRINT_PREMAIN_DSO_LOAD -o fips_premain_dso  \
        fips_premain.c fipscanister.o \
        libcrypto.a -Wl,--gc-sections -ldl
make[7]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl'
make[8]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl'
make[8]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl'
make[8]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl'
make[8]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl'
make[7]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl'
make[7]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl'
make[8]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl'
make[8]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl'
make[8]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl'
make[8]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl'
make[7]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl'
make[6]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl'
make[5]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl/ssl'
making all in apps...
make[5]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl/apps'
rm -f openssl
shlib_target=; if [ -n "libcrypto.so.1.0.0 libssl.so.1.0.0" ]; then \
        shlib_target="linux-shared"; \
    elif [ -n "" ]; then \
      FIPSLD_CC="mipsel-uclibc-gcc"; CC=/usr/local/ssl/fips-2.0/bin/fipsld; export CC FIPSLD_CC; \
    fi; \
    LIBRARIES="-L.. -lssl  -L.. -lcrypto" ; \
    make -f ../Makefile.shared -e \
        APPNAME=openssl OBJECTS="openssl.o verify.o asn1pars.o req.o dgst.o dh.o dhparam.o enc.o passwd.o gendh.o errstr.o ca.o pkcs7.o crl2p7.o crl.o rsa.o rsautl.o dsa.o dsaparam.o ec.o ecparam.o x509.o genrsa.o gendsa.o genpkey.o s_server.o s_client.o speed.o s_time.o apps.o s_cb.o s_socket.o app_rand.o version.o sess_id.o ciphers.o nseq.o pkcs12.o pkcs8.o pkey.o pkeyparam.o pkeyutl.o spkac.o smime.o cms.o rand.o engine.o ocsp.o prime.o ts.o srp.o" \
        LIBDEPS=" $LIBRARIES -Wl,--gc-sections -ldl" \
        link_app.${shlib_target}
make[6]: Entering directory `/home/sehack/asuswrt/release/src/router/openssl/apps'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/bin/ld: warning: ld-uClibc.so.0, needed by /opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so, not found (try using -rpath or -rpath-link)
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libc.so: undefined reference to `_dl_app_init_array'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_load_shared_library'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_map_cache'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_malloc_function'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_perform_mips_global_got_relocations'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_protect_relro'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libc.so: undefined reference to `_dl_app_fini_array'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_run_init_array'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_errno'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_free_function'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_loaded_modules'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_lookup_hash'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_debug_addr'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_handles'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_symbol_tables'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_fixup'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_unmap_cache'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_run_fini_array'
/opt/brcm/K26/hndtools-mipsel-uclibc-4.2.4/bin/../lib/gcc/mipsel-linux-uclibc/4.2.4/../../../../mipsel-linux-uclibc/lib/libdl.so: undefined reference to `_dl_error_number'
collect2: ld returned 1 exit status
make[6]: *** [link_app.gnu] Error 1
make[6]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl/apps'
make[5]: *** [openssl] Error 2
make[5]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl/apps'
make[4]: *** [build_apps] Error 1
make[4]: Leaving directory `/home/sehack/asuswrt/release/src/router/openssl'
make[3]: *** [openssl] Error 2
make[3]: Leaving directory `/home/sehack/asuswrt/release/src/router'
make[2]: *** [all] Error 2
make[2]: Leaving directory `/home/sehack/asuswrt/release/src-ra-mt7620'
make[1]: *** [bin] Error 2
make[1]: Leaving directory `/home/sehack/asuswrt/release/src-ra-mt7620'
make: *** [rt-ac51u] Error 2
sehack@ubuntu:~/asuswrt/release/src-ra-mt7620$

I bieda.

Idź do forum: Oprogramowanie / Software

16 Odpowiedź przez sehack

(5 odpowiedzi, napisanych Oprogramowanie / Software)

Robiłem konfigurację z użyciem relayd, ta konfiguracja jest czysta tylko z połączeniem na radio1 w trybie klienta.

Idź do forum: Oprogramowanie / Software

17 Odpowiedź przez sehack

(5 odpowiedzi, napisanych Oprogramowanie / Software)

Ja już się gubię robiłem wszystko wg. poradnika i du.a.

To są link moje pliki z /etc/config/, proszę niech ktoś pomoże bo brak mi już sił.

Idź do forum: Oprogramowanie / Software

18 Temat przez sehack

(5 odpowiedzi, napisanych Oprogramowanie / Software)

Chciałbym skonfigurować sieć, posiadam zainstalowane sterowniki, a miałaby wyglądać tak:
jeden interfejs WiFi łączy się z ISP i przekazuje internet przez drugi interfejs WiFi i Lan.

Idź do forum: Oprogramowanie / Software

19 Odpowiedź przez sehack

(5 odpowiedzi, napisanych Oprogramowanie / Software)

Pobieramy firmware openwrt-15.05-ramips-mt7620-mt7620a-squashfs-sysupgrade.bin i zmieniamy nazwę na "test.bin"
Pobieramy program putty.
Pobieramy TFTPGui.

Ustawiamy adres IP dla połączenia Ethernetowego
Adres IP: 192.168.1.75
Brama domyślna: 255.255.255.0


Podłączamy przejściówkę i instalujemy sterowniki.
Podłączamy kabel Ethernetowy do routera [dowolny port LAN] i karty sieciowej.

Instalujemy TFTPGui, wchodzimy w folder C:\Program Files (x86)\TFTPgui\tftproot\
,wrzucamy obraz test.bin i klikamy Start

Rozbieramy router, lutujemy kable od przejściówki RS232 do jego płyty (RX,TX,GND) .
http://s8.postimg.org/6bxcrd29g/IMG_20150927_141424.jpg


Uruchamiamy putty, klikamy Serial w Serial line wpisujemy numer portu pod którym znajduje się RS232 np.COM3, a w Speed prędkość czyli 115200.
Klikamy Open
Wyłączamy i włączamy router, przechodzimy do putty i gdy wyświetlą się opcje do wyboru szybko wciskamy na klawiaturze 2, później dwukrotnie Ctrl+C, enter.
Router powinien się sflashować, czekamy ok 8min, uruchamiamy go ponownie, usuwamy adres IP z ustawień karty sieciowej.

Interfejs sieciowy dostępny jest pod adresem  http://192.168.1.1/
Nie ponoszę odpowiedzialności za uszkodzenia sprzętu, wszystko wykonujecie na własną odpowiedzialność.

PS. Dzięki cezary za naprowadzenie.

Idź do forum: Oprogramowanie / Software

20 Odpowiedź przez sehack

(5 odpowiedzi, napisanych Oprogramowanie / Software)

Ok, dowiedziałem się że mam wgrać firmware przez serial, polutowałem kable mam połączenie i teraz jak to się robi z poziomu terminala?

Idź do forum: Oprogramowanie / Software

21 Temat przez sehack

(5 odpowiedzi, napisanych Oprogramowanie / Software)

Cześć, dzisiaj kupiłem do zabawy Asus RT-AC51U, chciałbym uruchomić na nim OpenWrt. Na zagranicznym forum znalazłem poświęcony jemu wątek https://forum.openwrt.org/viewtopic.php?id=59938
Czy mógłby mi ktoś pomóc, poinstruować co robić, jak to ugryźć? Jeżeli będą potrzebne logi z Seriala to nie będzie żadnego problemu.

Idź do forum: Oprogramowanie / Software

22 Odpowiedź przez sehack

(651 odpowiedzi, napisanych Oprogramowanie / Software)

Udało się uruchomić USB, nie wiem jednak jak dodać nowy interfejs WLAN USB i zastanawia mnie czemu wykrywa urządzenia pod USB 1.1.

/$ dmesg
[    0.000000] Linux version 3.18.11 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45556) ) #1 Mon May 18 21:36:53 CEST 2015
[    0.000000] Detected Broadcom 0x6328 CPU revision b0
[    0.000000] CPU frequency is 320 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 53.46.51-56.46-55
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a075 (Broadcom BMIPS4350)
[    0.000000] board: board name: F@ST2704V2
[    0.000000] MIPS: machine is Sagem F@ST2704V2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8037c380, node_mem_map 81002730
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 59716K/65536K available (2809K kernel code, 139K rwdata, 660K rodata, 1312K init, 192K bss, 5820K reserved)
[    0.000000] NR_IRQS:256
[    0.036000] Calibrating delay loop... 319.74 BogoMIPS (lpj=639488)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060000] NET: Registered protocol family 16
[    0.300000] registering PCI controller with io_map_base unset
[    0.324000] PCI host bridge to bus 0000:00
[    0.328000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
[    0.332000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.336000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.340000] pci 0000:00:00.0: [14e4:6328] type 01 class 0x060400
[    0.340000] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.340000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.344000] pci 0000:01:00.0: [14e4:a8d8] type 00 class 0x028000
[    0.344000] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
[    0.344000] pci 0000:01:00.0: supports D1 D2
[    0.344000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.344000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[    0.344000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[    0.348000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[    0.352000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.356000] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
[    0.360000] Switched to clocksource MIPS
[    0.364000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    0.372000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[    0.376000] bcma: bus0: Found chip with id 43225, rev 0x01 and package 0x0A
[    0.384000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[    0.392000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[    0.404000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[    0.536000] bcma: bus0: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[    0.544000] bcma: bus0: Using fallback SPROM failed (err -2)
[    0.548000] bcma: bus0: No SPROM available
[    0.564000] bcma: bus0: Bus registered
[    0.568000] NET: Registered protocol family 2
[    0.576000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.584000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.588000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.596000] TCP: reno registered
[    0.600000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.604000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.612000] NET: Registered protocol family 1
[    0.616000] PCI: CLS 0 bytes, default 16
[    0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.632000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.636000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.648000] msgmni has been set to 116
[    0.652000] io scheduler noop registered
[    0.656000] io scheduler deadline registered (default)
[    0.664000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
[    0.672000] console [ttyS0] enabled
[    0.680000] bootconsole [early0] disabled
[    0.692000] m25p80 spi1.0: found s25sl064p, expected m25p80
[    0.700000] m25p80 spi1.0: s25sl064p (8192 Kbytes)
[    0.704000] bcm63xxpart: CFE boot tag found with version 6 and board type F@ST2704V2
[    0.712000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.720000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 135b86
[    0.728000] bcm63xxpart: Partition 2 is rootfs offset 145c86 and length 6aa37a
[    0.732000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
[    0.740000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
[    0.748000] 5 bcm63xxpart partitions found on MTD device spi1.0
[    0.756000] Creating 5 MTD partitions on "spi1.0":
[    0.760000] 0x000000000000-0x000000010000 : "CFE"
[    0.764000] 0x000000010100-0x000000145c86 : "kernel"
[    0.772000] 0x000000145c86-0x0000007f0000 : "rootfs"
[    0.780000] mtd: device 2 (rootfs) set to be root filesystem
[    0.796000] 1 squashfs-split partitions found on MTD device rootfs
[    0.800000] 0x000000370000-0x0000007f0000 : "rootfs_data"
[    0.808000] 0x0000007f0000-0x000000800000 : "nvram"
[    0.816000] 0x000000010000-0x0000007f0000 : "linux"
[    0.860000] b53_common: found switch: BCM63xx, rev 0
[    0.864000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.876000] TCP: cubic registered
[    0.876000] NET: Registered protocol family 17
[    0.884000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.896000] Bridge firewalling registered
[    0.900000] 8021q: 802.1Q VLAN Support v1.8
[    0.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.944000] Freeing unused kernel memory: 1312K (80398000 - 804e0000)
[    2.792000] init: failed to symlink /tmp -> /var
[    2.796000] init: Console is alive
[    2.800000] init: - watchdog -
[    3.604000] random: nonblocking pool is initialized
[    4.820000] init: - preinit -
[    7.712000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[    9.348000] jffs2: notice: (234) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 1 of xref (0 dead, 0 orphan) found.
[    9.380000] mount_root: switching to jffs2 overlay
[    9.476000] procd: - early -
[    9.476000] procd: - watchdog -
[   10.468000] procd: - ubus -
[   11.488000] procd: - init -
[   14.032000] NET: Registered protocol family 10
[   14.108000] usbcore: registered new interface driver usbfs
[   14.116000] usbcore: registered new interface driver hub
[   14.120000] usbcore: registered new device driver usb
[   14.136000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   14.148000] ehci-platform: EHCI generic platform driver
[   14.256000] ehci-platform ehci-platform: EHCI Host Controller
[   14.260000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[   14.268000] ehci-platform ehci-platform: irq 50, io mem 0xb0002500
[   14.288000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[   14.300000] hub 1-0:1.0: USB hub found
[   14.304000] hub 1-0:1.0: 1 port detected
[   14.324000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   14.388000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   14.404000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   14.412000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   14.440000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   14.476000] nf_conntrack version 0.5.0 (953 buckets, 3812 max)
[   14.604000] xt_time: kernel timezone is -0000
[   14.720000] cfg80211: Calling CRDA to update world regulatory domain
[   14.732000] cfg80211: World regulatory domain updated:
[   14.736000] cfg80211:  DFS Master region: unset
[   14.740000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   14.752000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.760000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   14.768000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   14.776000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.784000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   14.792000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   14.800000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   14.808000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   15.072000] PPP generic driver version 2.4.2
[   15.080000] NET: Registered protocol family 24
[   15.140000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
[   15.148000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[   15.156000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11, Version 0
[   15.164000] Broadcom 43xx driver loaded [ Features: PNL ]
[   15.608000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   18.760000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   21.468000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[   22.772000] usb 1-1: USB disconnect, device number 2
[   27.144000] usb 1-1: new high-speed USB device number 3 using ehci-platform
[   33.208000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[   33.228000] device eth0.1 entered promiscuous mode
[   33.232000] device eth0 entered promiscuous mode
[   33.252000] br-lan: port 1(eth0.1) entered forwarding state
[   33.256000] br-lan: port 1(eth0.1) entered forwarding state
[   35.260000] br-lan: port 1(eth0.1) entered forwarding state
[  120.216000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 1
[  122.220000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[  166.892000] br-lan: port 1(eth0.1) entered disabled state
[  166.904000] device eth0.1 left promiscuous mode
[  166.908000] device eth0 left promiscuous mode
[  166.912000] br-lan: port 1(eth0.1) entered disabled state
[  166.928000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[  167.024000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[  167.056000] device eth0.1 entered promiscuous mode
[  167.064000] device eth0 entered promiscuous mode
[  167.088000] br-lan: port 1(eth0.1) entered forwarding state
[  167.092000] br-lan: port 1(eth0.1) entered forwarding state
[  169.096000] br-lan: port 1(eth0.1) entered forwarding state

Idź do forum: Oprogramowanie / Software

23 Odpowiedź przez sehack

(651 odpowiedzi, napisanych Oprogramowanie / Software)

Te moduły wgrałem http://wrzuc.se/thumbs/557877cce0ee4.png
przy libusb był jakiś problem.

Idź do forum: Oprogramowanie / Software

24 Odpowiedź przez sehack

(651 odpowiedzi, napisanych Oprogramowanie / Software)

Po wpisaniu dmesg wyświetla:

[    0.000000] Linux version 3.18.11 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45556) ) #1 Mon May 18 21:36:53 CEST 2015
[    0.000000] Detected Broadcom 0x6328 CPU revision b0
[    0.000000] CPU frequency is 320 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 53.46.51-56.46-55
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a075 (Broadcom BMIPS4350)
[    0.000000] board: board name: F@ST2704V2
[    0.000000] MIPS: machine is Sagem F@ST2704V2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8037c380, node_mem_map 81002730
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 59716K/65536K available (2809K kernel code, 139K rwdata, 660K rodata, 1312K init, 192K bss, 5820K reserved)
[    0.000000] NR_IRQS:256
[    0.036000] Calibrating delay loop... 319.74 BogoMIPS (lpj=639488)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060000] NET: Registered protocol family 16
[    0.300000] registering PCI controller with io_map_base unset
[    0.324000] PCI host bridge to bus 0000:00
[    0.328000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
[    0.332000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.336000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.340000] pci 0000:00:00.0: [14e4:6328] type 01 class 0x060400
[    0.340000] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.340000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.344000] pci 0000:01:00.0: [14e4:a8d8] type 00 class 0x028000
[    0.344000] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
[    0.344000] pci 0000:01:00.0: supports D1 D2
[    0.344000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.344000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[    0.344000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[    0.348000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[    0.352000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.356000] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
[    0.360000] Switched to clocksource MIPS
[    0.364000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    0.372000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[    0.376000] bcma: bus0: Found chip with id 43225, rev 0x01 and package 0x0A
[    0.384000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[    0.392000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[    0.404000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[    0.536000] bcma: bus0: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[    0.544000] bcma: bus0: Using fallback SPROM failed (err -2)
[    0.548000] bcma: bus0: No SPROM available
[    0.564000] bcma: bus0: Bus registered
[    0.568000] NET: Registered protocol family 2
[    0.576000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.584000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.588000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.596000] TCP: reno registered
[    0.600000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.604000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.612000] NET: Registered protocol family 1
[    0.616000] PCI: CLS 0 bytes, default 16
[    0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.632000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.636000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.648000] msgmni has been set to 116
[    0.652000] io scheduler noop registered
[    0.656000] io scheduler deadline registered (default)
[    0.664000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
[    0.672000] console [ttyS0] enabled
[    0.680000] bootconsole [early0] disabled
[    0.692000] m25p80 spi1.0: found s25sl064p, expected m25p80
[    0.700000] m25p80 spi1.0: s25sl064p (8192 Kbytes)
[    0.704000] bcm63xxpart: CFE boot tag found with version 6 and board type F@ST2704V2
[    0.712000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.720000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 135b86
[    0.728000] bcm63xxpart: Partition 2 is rootfs offset 145c86 and length 6aa37a
[    0.732000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
[    0.740000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
[    0.748000] 5 bcm63xxpart partitions found on MTD device spi1.0
[    0.756000] Creating 5 MTD partitions on "spi1.0":
[    0.760000] 0x000000000000-0x000000010000 : "CFE"
[    0.764000] 0x000000010100-0x000000145c86 : "kernel"
[    0.772000] 0x000000145c86-0x0000007f0000 : "rootfs"
[    0.780000] mtd: device 2 (rootfs) set to be root filesystem
[    0.796000] 1 squashfs-split partitions found on MTD device rootfs
[    0.800000] 0x000000370000-0x0000007f0000 : "rootfs_data"
[    0.808000] 0x0000007f0000-0x000000800000 : "nvram"
[    0.816000] 0x000000010000-0x0000007f0000 : "linux"
[    0.860000] b53_common: found switch: BCM63xx, rev 0
[    0.864000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.876000] TCP: cubic registered
[    0.876000] NET: Registered protocol family 17
[    0.884000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.896000] Bridge firewalling registered
[    0.900000] 8021q: 802.1Q VLAN Support v1.8
[    0.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.944000] Freeing unused kernel memory: 1312K (80398000 - 804e0000)
[    2.792000] init: failed to symlink /tmp -> /var
[    2.796000] init: Console is alive
[    2.800000] init: - watchdog -
[    3.604000] random: nonblocking pool is initialized
[    4.820000] init: - preinit -
[    5.716000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[    9.296000] mount_root: no usable overlay filesystem found, using tmpfs overlay
[    9.356000] procd: - early -
[    9.360000] procd: - watchdog -
[   10.216000] procd: - ubus -
[   11.228000] procd: - init -
[   13.108000] NET: Registered protocol family 10
[   13.124000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   13.152000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   13.160000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   13.176000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.200000] nf_conntrack version 0.5.0 (953 buckets, 3812 max)
[   13.276000] xt_time: kernel timezone is -0000
[   13.340000] cfg80211: Calling CRDA to update world regulatory domain
[   13.368000] cfg80211: World regulatory domain updated:
[   13.372000] cfg80211:  DFS Master region: unset
[   13.376000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   13.388000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   13.396000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   13.404000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   13.412000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   13.420000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   13.428000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   13.436000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   13.444000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   13.596000] PPP generic driver version 2.4.2
[   13.604000] NET: Registered protocol family 24
[   13.664000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
[   13.672000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[   13.680000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11, Version 0
[   13.688000] Broadcom 43xx driver loaded [ Features: PNL ]
[   13.884000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   20.820000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[   26.376000] jffs2: notice: (767) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   29.932000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[   29.968000] device eth0.1 entered promiscuous mode
[   29.972000] device eth0 entered promiscuous mode
[   30.004000] br-lan: port 1(eth0.1) entered forwarding state
[   30.008000] br-lan: port 1(eth0.1) entered forwarding state
[   32.012000] br-lan: port 1(eth0.1) entered forwarding state
[  139.940000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 1
[  141.944000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[  625.952000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 1
[  627.956000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[  756.036000] usbcore: Unknown symbol utf16s_to_utf8s (err 0)
[  756.252000] ohci_hcd: Unknown symbol usb_hcd_unlink_urb_from_ep (err 0)
[  756.260000] ohci_hcd: Unknown symbol usb_hc_died (err 0)
[  756.264000] ohci_hcd: Unknown symbol usb_disabled (err 0)
[  756.272000] ohci_hcd: Unknown symbol usb_hcd_check_unlink_urb (err 0)
[  756.276000] ohci_hcd: Unknown symbol usb_hcds_loaded (err 0)
[  756.284000] ohci_hcd: Unknown symbol usb_calc_bus_time (err 0)
[  756.288000] ohci_hcd: Unknown symbol usb_hcd_link_urb_to_ep (err 0)
[  756.296000] ohci_hcd: Unknown symbol usb_hcd_giveback_urb (err 0)
[  756.300000] ohci_hcd: Unknown symbol usb_hcd_poll_rh_status (err 0)
[  756.308000] ohci_hcd: Unknown symbol usb_debug_root (err 0)
[  756.332000] ohci_platform: Unknown symbol usb_hcd_platform_shutdown (err 0)
[  756.340000] ohci_platform: Unknown symbol usb_disabled (err 0)
[  756.344000] ohci_platform: Unknown symbol ohci_setup (err 0)
[  756.352000] ohci_platform: Unknown symbol usb_put_hcd (err 0)
[  756.356000] ohci_platform: Unknown symbol ohci_init_driver (err 0)
[  756.364000] ohci_platform: Unknown symbol usb_create_hcd (err 0)
[  756.368000] ohci_platform: Unknown symbol usb_remove_hcd (err 0)
[  756.376000] ohci_platform: Unknown symbol usb_add_hcd (err 0)
[  756.592000] ehci_hcd: Unknown symbol usb_hcd_unlink_urb_from_ep (err 0)
[  756.600000] ehci_hcd: Unknown symbol usb_hcd_start_port_resume (err 0)
[  756.608000] ehci_hcd: Unknown symbol usb_hc_died (err 0)
[  756.612000] ehci_hcd: Unknown symbol usb_disabled (err 0)
[  756.620000] ehci_hcd: Unknown symbol usb_hcd_check_unlink_urb (err 0)
[  756.624000] ehci_hcd: Unknown symbol usb_hcds_loaded (err 0)
[  756.632000] ehci_hcd: Unknown symbol usb_hcd_end_port_resume (err 0)
[  756.636000] ehci_hcd: Unknown symbol usb_calc_bus_time (err 0)
[  756.644000] ehci_hcd: Unknown symbol ehci_cf_port_reset_rwsem (err 0)
[  756.652000] ehci_hcd: Unknown symbol usb_hcd_link_urb_to_ep (err 0)
[  756.656000] ehci_hcd: Unknown symbol usb_hub_clear_tt_buffer (err 0)
[  756.664000] ehci_hcd: Unknown symbol usb_hcd_giveback_urb (err 0)
[  756.672000] ehci_hcd: Unknown symbol usb_hcd_poll_rh_status (err 0)
[  756.716000] ehci_platform: Unknown symbol usb_hcd_platform_shutdown (err 0)
[  756.724000] ehci_platform: Unknown symbol usb_disabled (err 0)
[  756.728000] ehci_platform: Unknown symbol ehci_init_driver (err 0)
[  756.736000] ehci_platform: Unknown symbol usb_put_hcd (err 0)
[  756.740000] ehci_platform: Unknown symbol ehci_setup (err 0)
[  756.748000] ehci_platform: Unknown symbol usb_create_hcd (err 0)
[  756.756000] ehci_platform: Unknown symbol usb_remove_hcd (err 0)
[  756.760000] ehci_platform: Unknown symbol usb_add_hcd (err 0)
[  913.964000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 1
[  915.968000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 1037.976000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 1
[ 1039.980000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 1103.876000] usbcore: Unknown symbol utf16s_to_utf8s (err 0)
[ 1104.232000] ledtrig_usbdev: Unknown symbol usb_put_dev (err 0)
[ 1104.236000] ledtrig_usbdev: Unknown symbol usb_get_dev (err 0)
[ 1104.244000] ledtrig_usbdev: Unknown symbol usb_unregister_notify (err 0)
[ 1104.252000] ledtrig_usbdev: Unknown symbol usb_register_notify (err 0)
[ 1104.256000] ledtrig_usbdev: Unknown symbol usb_find_device_by_name (err 0)
[ 1104.476000] ohci_hcd: Unknown symbol usb_hcd_unlink_urb_from_ep (err 0)
[ 1104.484000] ohci_hcd: Unknown symbol usb_hc_died (err 0)
[ 1104.488000] ohci_hcd: Unknown symbol usb_disabled (err 0)
[ 1104.492000] ohci_hcd: Unknown symbol usb_hcd_check_unlink_urb (err 0)
[ 1104.500000] ohci_hcd: Unknown symbol usb_hcds_loaded (err 0)
[ 1104.508000] ohci_hcd: Unknown symbol usb_calc_bus_time (err 0)
[ 1104.512000] ohci_hcd: Unknown symbol usb_hcd_link_urb_to_ep (err 0)
[ 1104.520000] ohci_hcd: Unknown symbol usb_hcd_giveback_urb (err 0)
[ 1104.524000] ohci_hcd: Unknown symbol usb_hcd_poll_rh_status (err 0)
[ 1104.532000] ohci_hcd: Unknown symbol usb_debug_root (err 0)
[ 1104.556000] ohci_platform: Unknown symbol usb_hcd_platform_shutdown (err 0)
[ 1104.564000] ohci_platform: Unknown symbol usb_disabled (err 0)
[ 1104.568000] ohci_platform: Unknown symbol ohci_setup (err 0)
[ 1104.576000] ohci_platform: Unknown symbol usb_put_hcd (err 0)
[ 1104.580000] ohci_platform: Unknown symbol ohci_init_driver (err 0)
[ 1104.588000] ohci_platform: Unknown symbol usb_create_hcd (err 0)
[ 1104.592000] ohci_platform: Unknown symbol usb_remove_hcd (err 0)
[ 1104.600000] ohci_platform: Unknown symbol usb_add_hcd (err 0)
[ 1105.380000] ehci_hcd: Unknown symbol usb_hcd_unlink_urb_from_ep (err 0)
[ 1105.388000] ehci_hcd: Unknown symbol usb_hcd_start_port_resume (err 0)
[ 1105.396000] ehci_hcd: Unknown symbol usb_hc_died (err 0)
[ 1105.400000] ehci_hcd: Unknown symbol usb_disabled (err 0)
[ 1105.408000] ehci_hcd: Unknown symbol usb_hcd_check_unlink_urb (err 0)
[ 1105.412000] ehci_hcd: Unknown symbol usb_hcds_loaded (err 0)
[ 1105.420000] ehci_hcd: Unknown symbol usb_hcd_end_port_resume (err 0)
[ 1105.424000] ehci_hcd: Unknown symbol usb_calc_bus_time (err 0)
[ 1105.432000] ehci_hcd: Unknown symbol ehci_cf_port_reset_rwsem (err 0)
[ 1105.440000] ehci_hcd: Unknown symbol usb_hcd_link_urb_to_ep (err 0)
[ 1105.444000] ehci_hcd: Unknown symbol usb_hub_clear_tt_buffer (err 0)
[ 1105.452000] ehci_hcd: Unknown symbol usb_hcd_giveback_urb (err 0)
[ 1105.456000] ehci_hcd: Unknown symbol usb_hcd_poll_rh_status (err 0)
[ 1105.484000] ehci_platform: Unknown symbol usb_hcd_platform_shutdown (err 0)
[ 1105.488000] ehci_platform: Unknown symbol usb_disabled (err 0)
[ 1105.496000] ehci_platform: Unknown symbol ehci_init_driver (err 0)
[ 1105.504000] ehci_platform: Unknown symbol usb_put_hcd (err 0)
[ 1105.508000] ehci_platform: Unknown symbol ehci_setup (err 0)
[ 1105.516000] ehci_platform: Unknown symbol usb_create_hcd (err 0)
[ 1105.520000] ehci_platform: Unknown symbol usb_remove_hcd (err 0)
[ 1105.528000] ehci_platform: Unknown symbol usb_add_hcd (err 0)
[ 1236.940000] usbcore: Unknown symbol utf16s_to_utf8s (err 0)
[ 1310.700000] ehci_hcd: Unknown symbol usb_hcd_unlink_urb_from_ep (err 0)
[ 1310.708000] ehci_hcd: Unknown symbol usb_hcd_start_port_resume (err 0)
[ 1310.716000] ehci_hcd: Unknown symbol usb_hc_died (err 0)
[ 1310.720000] ehci_hcd: Unknown symbol usb_disabled (err 0)
[ 1310.728000] ehci_hcd: Unknown symbol usb_hcd_check_unlink_urb (err 0)
[ 1310.732000] ehci_hcd: Unknown symbol usb_hcds_loaded (err 0)
[ 1310.740000] ehci_hcd: Unknown symbol usb_hcd_end_port_resume (err 0)
[ 1310.744000] ehci_hcd: Unknown symbol usb_calc_bus_time (err 0)
[ 1310.752000] ehci_hcd: Unknown symbol ehci_cf_port_reset_rwsem (err 0)
[ 1310.760000] ehci_hcd: Unknown symbol usb_hcd_link_urb_to_ep (err 0)
[ 1310.764000] ehci_hcd: Unknown symbol usb_hub_clear_tt_buffer (err 0)
[ 1310.772000] ehci_hcd: Unknown symbol usb_hcd_giveback_urb (err 0)
[ 1310.776000] ehci_hcd: Unknown symbol usb_hcd_poll_rh_status (err 0)
[ 1608.988000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 1
[ 1610.992000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 1839.000000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 1
[ 1841.004000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 1972.012000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 1
[ 1974.016000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 2742.024000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 1
[ 2744.028000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex

Idź do forum: Oprogramowanie / Software

25 Odpowiedź przez sehack

(651 odpowiedzi, napisanych Oprogramowanie / Software)

@up
Dobra używam już najnowszych modułów, ale jest problem z instalacją USB. Proszę podeślijcie nazwy potrzebnych modułów do zainstalowania, bo już mam dosyć pobierania ręcznego tych modułów i wrzucania ich przez SCP.

Idź do forum: Oprogramowanie / Software