Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Posty przez bartwr
Planuję zakup tp-link Archer C2300 jest planowana kompilacja luci?
W bazie nie znalazłem, ale jest model c2600 teoretycznie podobny.
Co sądzicie o tp-link Archer C2300. Może doradzicie coś lepszego w cenie do 600 zł?
Chodzi mi o udostępnianie mediów (filmy) z podłączonego przez USB hdd.
po extroot flash wygląda o wiele lepiej:
Flash: total: 475.2MB, free: 461.9MB, used: 2%
minidlna uruchomiło się 
wielkie dzięki i problem rozwiązany było za mało pamięci i dlatego router nie mógł dać rady
no tak, to by wiele wyjaśniało - myślałem, że aktualizacja jest robiona na extroot - to robię extroota
po wpisaniu:
mkdir -p /mnt/sdb1
ntfs-3g /dev/sdb1 /mnt/sdb1 -o rw,sync
pokazuje się komunikat:
ntfs-3g /dev/sdb1 /mnt/sdb1 -o rw,sync
NTFS signature is missing.
Failed to mount '/dev/sdb1': Invalid argument
The device '/dev/sdb1' doesn't seem to have a valid NTFS.
Maybe the wrong device is used? Or the whole disk instead of a
partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around?
czyli tak jakby nie widział partycji. Jak podłączam ten sam dysk starym adapterem - montuje się bez problemu
czyli powinienem przejść na BB? extroot nie rozwiązuje tego problemu? przed aktualizacją miałem zrobione extroot - może rozjechało się.
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 7.410000] eth0: link up (1000Mbps/Full duplex)
Fri Apr 15 07:17:26 2016 user.info kernel: [ 9.460000] mount_root: loading kmods from internal overlay
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 9.470000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 2 is up
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 9.470000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up
Fri Apr 15 07:17:26 2016 kern.notice kernel: [ 9.810000] jffs2: notice: (458) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Fri Apr 15 07:17:26 2016 user.info kernel: [ 9.830000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Fri Apr 15 07:17:26 2016 user.info kernel: [ 9.840000] block: extroot: not configured
Fri Apr 15 07:17:26 2016 kern.notice kernel: [ 9.900000] jffs2: notice: (455) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Fri Apr 15 07:17:26 2016 user.info kernel: [ 9.910000] mount_root: loading kmods from internal overlay
Fri Apr 15 07:17:26 2016 user.err kernel: [ 9.930000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/gre.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 9.940000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/ip6_tables.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 9.950000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/ip6t_REJECT.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 9.960000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/ip6table_filter.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 9.970000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/ip6table_mangle.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 9.980000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/ip6table_raw.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 9.990000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/ip_gre.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 9.990000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/ipv6.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 10.000000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/nf_conntrack_ipv6.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 10.010000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/nf_defrag_ipv6.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 10.020000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/nf_log_ipv6.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 10.030000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/nf_reject_ipv6.ko
Fri Apr 15 07:17:26 2016 user.err kernel: [ 10.040000] kmodloader: failed to stat /tmp/overlay/upper/lib/modules/3.18.27/pptp.ko
Fri Apr 15 07:17:26 2016 user.info kernel: [ 10.250000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Fri Apr 15 07:17:26 2016 user.info kernel: [ 10.260000] block: extroot: not configured
Fri Apr 15 07:17:26 2016 user.info kernel: [ 10.270000] mount_root: switching to jffs2 overlay
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 10.300000] eth0: link down
Fri Apr 15 07:17:26 2016 user.info kernel: [ 10.320000] procd: - early -
Fri Apr 15 07:17:26 2016 user.info kernel: [ 10.320000] procd: - watchdog -
Fri Apr 15 07:17:26 2016 user.info kernel: [ 11.180000] procd: - ubus -
Fri Apr 15 07:17:26 2016 user.info kernel: [ 12.210000] procd: - init -
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 14.930000] u32 classifier
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 14.940000] input device check on
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 14.940000] Actions configured
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 14.950000] Mirror/redirect action on
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 14.990000] fuse init (API version 7.23)
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.010000] usbcore: registered new interface driver cdc_acm
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.020000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.030000] usbcore: registered new interface driver cdc_wdm
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.040000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.040000] Backport generated by backports.git backports-20151218-0-g2f58d9d
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.060000] ip_tables: (C) 2000-2006 Netfilter Core Team
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.090000] nf_conntrack version 0.5.0 (1969 buckets, 7876 max)
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.110000] usbcore: registered new interface driver usblp
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.140000] usbcore: registered new interface driver usbserial
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.150000] usbcore: registered new interface driver usbserial_generic
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.150000] usbserial: USB Serial support registered for generic
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.200000] xt_time: kernel timezone is -0000
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.220000] usbcore: registered new interface driver cdc_ether
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.230000] usbcore: registered new interface driver cdc_ncm
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.290000] usbcore: registered new interface driver huawei_cdc_ncm
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.350000] PPP generic driver version 2.4.2
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.350000] PPP MPPE Compression module registered
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.360000] NET: Registered protocol family 24
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.370000] usbcore: registered new interface driver qmi_wwan
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.380000] usbcore: registered new interface driver rndis_host
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.390000] usbcore: registered new interface driver sierra
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.390000] usbserial: USB Serial support registered for Sierra USB modem
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.400000] usbcore: registered new interface driver sierra_net
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.450000] usbcore: registered new interface driver cdc_mbim
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.470000] usbcore: registered new interface driver option
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.470000] usbserial: USB Serial support registered for GSM modem (1-port)
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.480000] usbcore: registered new interface driver qcserial
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.490000] usbserial: USB Serial support registered for Qualcomm USB modem
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.530000] ath: EEPROM regdomain: 0x0
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.530000] ath: EEPROM indicates default country code should be used
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.530000] ath: doing EEPROM country->regdmn map search
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.530000] ath: country maps to regdmn code: 0x3a
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.530000] ath: Country alpha2 being used: US
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.530000] ath: Regpair used: 0x3a
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.540000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.540000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
Fri Apr 15 07:17:26 2016 kern.warn kernel: [ 15.550000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.560000] ath: EEPROM regdomain: 0x0
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.560000] ath: EEPROM indicates default country code should be used
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.560000] ath: doing EEPROM country->regdmn map search
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.560000] ath: country maps to regdmn code: 0x3a
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.560000] ath: Country alpha2 being used: US
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.560000] ath: Regpair used: 0x3a
Fri Apr 15 07:17:26 2016 kern.debug kernel: [ 15.570000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.570000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
Fri Apr 15 07:17:26 2016 kern.notice kernel: [ 15.630000] random: nonblocking pool is initialized
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.690000] EXT4-fs (sda1): recovery complete
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.690000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
Fri Apr 15 07:17:26 2016 kern.warn kernel: [ 15.920000] EXT4-fs (sda5): warning: maximal mount count reached, running e2fsck is recommended
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.930000] EXT4-fs (sda5): recovery complete
Fri Apr 15 07:17:26 2016 kern.info kernel: [ 15.930000] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts:
Fri Apr 15 07:17:28 2016 user.emerg syslog: 'radio0' is disabled
Fri Apr 15 07:17:29 2016 user.emerg syslog: 'radio0' is disabled
Fri Apr 15 07:17:29 2016 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Fri Apr 15 07:17:30 2016 daemon.err odhcpd[1349]: Failed to open routing table: No such file or directory
Fri Apr 15 07:17:30 2016 daemon.err odhcpd[1349]: Unable to open raw socket: Address family not supported by protocol
Fri Apr 15 07:17:30 2016 daemon.err block: mounting /dev/mtdblock2 (squashfs) as /mnt/mtdblock2 failed (-1) - Unknown error -1
Fri Apr 15 07:17:30 2016 daemon.err block: /dev/mtdblock3 is already mounted
Fri Apr 15 07:17:30 2016 daemon.err block: /dev/sda1 is already mounted
Fri Apr 15 07:17:30 2016 daemon.err block: /dev/sda5 is already mounted
Fri Apr 15 07:17:30 2016 cron.info crond[1388]: crond (busybox 1.23.2) started, log level 5
Fri Apr 15 07:17:31 2016 authpriv.info dropbear[1406]: Not backgrounding
Fri Apr 15 07:17:35 2016 daemon.err odhcpd[1770]: Failed to open routing table: No such file or directory
Fri Apr 15 07:17:35 2016 daemon.err odhcpd[1770]: Unable to open raw socket: Address family not supported by protocol
Fri Apr 15 07:17:35 2016 daemon.err uhttpd[1778]: socket(): Address family not supported by protocol
Fri Apr 15 07:17:35 2016 daemon.err uhttpd[1778]: socket(): Address family not supported by protocol
Fri Apr 15 07:17:35 2016 kern.info kernel: [ 27.690000] device eth0.1 entered promiscuous mode
Fri Apr 15 07:17:35 2016 kern.info kernel: [ 27.690000] device eth0 entered promiscuous mode
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Interface 'lan' is enabled
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Interface 'lan' is setting up now
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Interface 'lan' is now up
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Interface 'loopback' is enabled
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Interface 'loopback' is setting up now
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Interface 'loopback' is now up
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Interface 'wan' is enabled
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Interface 'wan6' is enabled
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Network device 'lo' link is up
Fri Apr 15 07:17:36 2016 daemon.notice netifd: Interface 'loopback' has link connectivity
Fri Apr 15 07:17:37 2016 kern.info kernel: [ 29.140000] eth0: link up (1000Mbps/Full duplex)
Fri Apr 15 07:17:37 2016 daemon.notice netifd: Network device 'eth0' link is up
Fri Apr 15 07:17:37 2016 daemon.notice netifd: VLAN 'eth0.1' link is up
Fri Apr 15 07:17:37 2016 daemon.notice netifd: VLAN 'eth0.2' link is up
Fri Apr 15 07:17:37 2016 daemon.notice netifd: Interface 'wan' has link connectivity
Fri Apr 15 07:17:37 2016 daemon.notice netifd: Interface 'wan' is setting up now
Fri Apr 15 07:17:37 2016 daemon.notice netifd: Interface 'wan6' has link connectivity
Fri Apr 15 07:17:37 2016 daemon.notice netifd: Interface 'wan6' is setting up now
Fri Apr 15 07:17:37 2016 kern.info kernel: [ 29.240000] br-lan: port 1(eth0.1) entered forwarding state
Fri Apr 15 07:17:37 2016 kern.info kernel: [ 29.250000] br-lan: port 1(eth0.1) entered forwarding state
Fri Apr 15 07:17:37 2016 daemon.notice netifd: Interface 'wan6' is now up
Fri Apr 15 07:17:37 2016 daemon.notice netifd: Bridge 'br-lan' link is up
Fri Apr 15 07:17:37 2016 daemon.notice netifd: Interface 'lan' has link connectivity
Fri Apr 15 07:17:38 2016 daemon.notice netifd: wan (1966): udhcpc (v1.23.2) started
Fri Apr 15 07:17:38 2016 daemon.notice netifd: wan (1966): Sending discover...
Fri Apr 15 07:17:38 2016 user.emerg syslog: NTFS signature is missing.
Fri Apr 15 07:17:38 2016 user.emerg syslog: Failed to mount '/dev/sdb1': Invalid argument
Fri Apr 15 07:17:38 2016 user.emerg syslog: The device '/dev/sdb1' doesn't seem to have a valid NTFS.
Fri Apr 15 07:17:38 2016 user.emerg syslog: Maybe the wrong device is used? Or the whole disk instead of a
Fri Apr 15 07:17:38 2016 user.emerg syslog: partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around?
Fri Apr 15 07:17:39 2016 user.emerg syslog: setting up led USB1
Fri Apr 15 07:17:39 2016 user.emerg syslog: setting up led USB2
Fri Apr 15 07:17:39 2016 kern.info kernel: [ 31.250000] br-lan: port 1(eth0.1) entered forwarding state
Fri Apr 15 07:17:39 2016 daemon.notice netifd: radio1 (1818): Configuration file: /var/run/hostapd-phy1.conf
Fri Apr 15 07:17:39 2016 kern.info kernel: [ 31.500000] device wlan1 entered promiscuous mode
Fri Apr 15 07:17:39 2016 daemon.notice netifd: radio1 (1818): wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Fri Apr 15 07:17:39 2016 daemon.notice netifd: radio1 (1818): Using interface wlan1 with hwaddr f8:1a:67:33:09:66 and ssid "\xc5\x9awistak 5"
Fri Apr 15 07:17:39 2016 daemon.info procd: - init complete -
Fri Apr 15 07:17:40 2016 daemon.err odhcpd[2070]: Failed to open routing table: No such file or directory
Fri Apr 15 07:17:40 2016 daemon.err odhcpd[2070]: Unable to open raw socket: Address family not supported by protocol
Fri Apr 15 07:17:40 2016 kern.info kernel: [ 31.990000] br-lan: port 2(wlan1) entered forwarding state
Fri Apr 15 07:17:40 2016 kern.info kernel: [ 31.990000] br-lan: port 2(wlan1) entered forwarding state
Fri Apr 15 07:17:40 2016 daemon.notice netifd: radio1 (1818): wlan1: interface state COUNTRY_UPDATE->ENABLED
Fri Apr 15 07:17:40 2016 daemon.notice netifd: radio1 (1818): wlan1: AP-ENABLED
Fri Apr 15 07:17:40 2016 daemon.notice netifd: Network device 'wlan1' link is up
Fri Apr 15 07:17:40 2016 user.notice dnsmasq: found already running DHCP-server on interface 'br-lan' refusing to start, use 'option force 1' to override
Fri Apr 15 07:17:40 2016 daemon.info dnsmasq[2139]: started, version 2.73 cachesize 150
Fri Apr 15 07:17:40 2016 daemon.info dnsmasq[2139]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify
Fri Apr 15 07:17:40 2016 daemon.info dnsmasq[2139]: DNS service limited to local subnets
Fri Apr 15 07:17:40 2016 daemon.info dnsmasq[2139]: using local addresses only for domain lan
Fri Apr 15 07:17:40 2016 daemon.info dnsmasq[2139]: reading /tmp/resolv.conf.auto
Fri Apr 15 07:17:40 2016 daemon.info dnsmasq[2139]: using local addresses only for domain lan
Fri Apr 15 07:17:40 2016 daemon.info dnsmasq[2139]: using nameserver 8.8.8.8#53
Fri Apr 15 07:17:40 2016 daemon.info dnsmasq[2139]: read /etc/hosts - 1 addresses
Fri Apr 15 07:17:40 2016 daemon.info dnsmasq[2139]: read /tmp/hosts/dhcp - 1 addresses
Fri Apr 15 07:17:41 2016 daemon.notice netifd: wan (1966): Sending discover...
Fri Apr 15 07:17:42 2016 kern.info kernel: [ 33.990000] br-lan: port 2(wlan1) entered forwarding state
Fri Apr 15 07:17:43 2016 user.notice firewall: Reloading firewall due to ifup of wan6 (eth0.2)
Fri Apr 15 07:17:44 2016 user.notice ddns-scripts[2356]: myddns_ipv6: PID '2356' started at 2016-04-15 07:17
Fri Apr 15 07:17:44 2016 user.warn ddns-scripts[2356]: myddns_ipv6: Service section disabled! - TERMINATE
Fri Apr 15 07:17:44 2016 user.warn ddns-scripts[2356]: myddns_ipv6: PID '2356' exit WITH ERROR '1' at 2016-04-15 07:17
Fri Apr 15 07:17:44 2016 daemon.notice netifd: wan (1966): Sending discover...
Fri Apr 15 07:17:45 2016 daemon.err odhcpd[2405]: Failed to open routing table: No such file or directory
Fri Apr 15 07:17:45 2016 daemon.err odhcpd[2405]: Unable to open raw socket: Address family not supported by protocol
Fri Apr 15 07:17:50 2016 daemon.err odhcpd[2411]: Failed to open routing table: No such file or directory
Fri Apr 15 07:17:50 2016 daemon.err odhcpd[2411]: Unable to open raw socket: Address family not supported by protocol
Fri Apr 15 22:48:31 2016 daemon.err odhcpd[2417]: Failed to open routing table: No such file or directory
Fri Apr 15 22:48:31 2016 daemon.err odhcpd[2417]: Unable to open raw socket: Address family not supported by protocol
Fri Apr 15 22:48:31 2016 daemon.info procd: Instance odhcpd::instance1 s in a crash loop 6 crashes, 0 seconds since last crash
Fri Apr 15 22:48:36 2016 cron.err crond[1388]: time disparity of 931 minutes detected
Fri Apr 15 22:50:34 2016 authpriv.info dropbear[2424]: Child connection from 192.168.0.11:60293
Fri Apr 15 22:50:41 2016 authpriv.notice dropbear[2424]: Password auth succeeded for 'root' from 192.168.0.11:60293
Fri Apr 15 22:51:20 2016 daemon.info hostapd: wlan1: STA 98:f1:70:0d:42:fb IEEE 802.11: authenticated
Fri Apr 15 22:51:20 2016 daemon.info hostapd: wlan1: STA 98:f1:70:0d:42:fb IEEE 802.11: associated (aid 1)
Fri Apr 15 22:51:20 2016 daemon.info hostapd: wlan1: STA 98:f1:70:0d:42:fb WPA: pairwise key handshake completed (WPA)
Fri Apr 15 22:51:20 2016 daemon.info hostapd: wlan1: STA 98:f1:70:0d:42:fb WPA: group key handshake completed (WPA)
Fri Apr 15 22:58:17 2016 daemon.info hostapd: wlan1: STA 98:f1:70:0d:42:fb WPA: group key handshake completed (WPA)
Fri Apr 15 23:05:12 2016 authpriv.info dropbear[3146]: Child connection from 192.168.0.11:60532
Fri Apr 15 23:05:15 2016 authpriv.notice dropbear[3146]: Password auth succeeded for 'root' from 192.168.0.11:60532
Fri Apr 15 23:08:17 2016 daemon.info hostapd: wlan1: STA 98:f1:70:0d:42:fb WPA: group key handshake completed (WPA)
sda to jest pendrive na którym mam zrobiony extroot
ale nie mogę już ponownie zainstalować z powodu braku pamięci flash... dopiero teraz zwróciłem na to uwagę. Wydaje mi się, że przy starszym flashe było więcej dostępnej pamięci.
----------------------------------------------------------------
| |
| OpenWrt Chaos Calmer 15.05.1 (r49087) |
| Build time: 2016-03-30 07:13 CEST |
| |
| Cezary Jackiewicz (obsy), http://eko.one.pl |
| |
----------------------------------------------------------------
| Machine: TP-Link TL-WDR3600 v1 |
| Uptime: 0d, 00:02:57 |
| Load: 0.18 0.28 0.13 |
| Flash: total: 1.6MB, free: 740KB, used: 54% |
| Memory: total: 123.1MB, free: 106.2MB, used: 13% |
aktualizowałem pakietem: luci-15.05-ar71xx-generic-tl-wdr3600-v1-squashfs-sysupgrade.bin
(niestety nie spisałem jaki miałem wcześniej 
root@OpenWrt:~# block info
/dev/mtdblock2: UUID="b958fb3d-25c38684-580a6a75-99b533eb" VERSION="4.0" TYPE="squashfs"
/dev/mtdblock3: TYPE="jffs2"
/dev/sda1: UUID="585ac2d5-6a59-4a48-90bd-ec5114ea5fa0" NAME="EXT_JOURNAL" VERSION="1.0" TYPE="ext4"
/dev/sda5: UUID="73fbe3be-eb85-d001-30eb-e1beeb85d001" LABEL="600" NAME="EXT_JOURNAL" VERSION="1.0" TYPE="ext4"
po prądowym restarcie udało się odinstalować - zniknęło z listy aplikacji
nie chce się zamontować. Na dysku są 2 partycje ext4 i ntfs - żadna nie jest widoczna.
poniżej zawartość fstab który działa na prostym adapterze z tym samym dyskiem:
config global
option anon_swap '0'
option anon_mount '1'
option auto_swap '1'
option auto_mount '1'
option delay_root '5'
option check_fs '0'
config mount
option target '/mnt/sda1'
option uuid '585ac2d5-6a59-4a48-90bd-ec5114ea5fa0'
option enabled '0'
config mount
option target '/mnt/sda5'
option uuid '73fbe3be-eb85-d001-30eb-e1beeb85d001'
option enabled '0'
config mount
option enabled '1'
option device '/dev/sdb1'
option target '/mnt/sdb1'
config mount
option enabled '1'
option device '/dev/sdb2'
option target '/mnt/sdb2'
musiałem użyc opcji force i poniżej wyniki:
opkg remove luci-app-minidlna --force-depends
Removing package luci-app-minidlna from root...
opkg remove minidlna --force-remove
Removing package minidlna from root...
Not deleting modified conffile /etc/config/minidlna.
Collected errors:
* pkg_run_script: package "minidlna" prerm script returned status 1.
czyli chyba samo minidlna nie jest odinstalowane (w LuCi ciągle widnieje na liście zainstalowanych pakietów.
Próbowałem, ale nie mogę odszukać informacji jak odinstalować minidlna ręcznie.
Przez interface LuCi nie działa.
Naciskam usuń i nie usuwa się.
Inne składniki (spolszczenie i GUI) dla minidlna pozwalają się odinstalować z poziomu LuCi.
poniżej:
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.18
S: Manufacturer=Linux 3.18.27 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=05e3 ProdID=0608 Rev=77.64
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=3538 ProdID=0901 Rev= 1.00
S: SerialNumber=01AF000000000208
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=480mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=abcd ProdID=6101 Rev= 2.03
S: Manufacturer=LogiLink
S: Product=PCCloneEX Lite+
S: SerialNumber=DB9876543211160
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 0 Alt= 1 #EPs= 4 Cls=08(stor.) Sub=06 Prot=62 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Witam,
po aktualizacji Chaos Calmer do wersji 15.05.1 r49087 na TP-Link TL-WDR3600 v1 przestało działać minidlna.
Przy próbie instalacji jest informacja, że pakiet jest aktualny:
opkg install minidlna
Package minidlna (1.1.4-2) installed in root is up to date.
Przy próbie startu pokazuje brak pliku:
/etc/init.d/minidlna start
/usr/bin/minidlna: can't load library 'libid3tag.so.0'
proszę o pomoc
Ja właśnie walczę z nową stacją dokującą LogiLink QP0010 - po podłączeniu do Luci nie działa.
Wcześniejsze rozwiązanie z dyskiem podłączonym adapterem Unitek śmiga bez problemu.
Może ktoś ma jakieś pozytywne doświadczenia ze stacjami dokującymi dla HDD?
Działa - miałem błędnie wpisana bramę routera.
W katalogu /etc/hotplug.d/block mam 1 plik 10-mount
Czy powinienem utworzyć nowy plik, w którym umieszczę komendy:
mkdir -p /mnt/dysk1
ntfs-3g /dev/sda1 /mnt/dysk1 -o rw,sync
fdisk -l | grep NTFS
Czy zamiast /dev/sda1 użyć UUDI dysku, czy nie ma potrzeby używać UUID?
Czy podmontują się dwie partycje z dysku?
Gapiostwo - opkg update zgłaszało błędy, miałem źle wpisaną bramę w konfiguracji sieci.
dlna zainstalowane - teraz uczę się konfiguracji
poniżej listingi:
root@OpenWrt:~# cat /etc/banner
_ _____ _____
| | / ____|_ _|
| | _ _| | | |
| | | | | | | | |
| |___| |_| | |____ _| |_
|______\__,_|\_____|_____|
----------------------------------------------------------------
| |
| OpenWrt Barrier Breaker (r44952) |
| Build time: 2015-03-28 08:47 CET |
| |
| Cezary Jackiewicz (obsy), http://eko.one.pl |
| |
----------------------------------------------------------------
root@OpenWrt:~# cat /etc/opkg.conf
dest root /
dest ram /tmp
lists_dir ext /var/opkg-lists
option overlay_root /overlay
src/gz barrier_breaker_base http://downloads.openwrt.org/barrier_br … kages/base
src/gz barrier_breaker_luci http://downloads.openwrt.org/barrier_br … kages/luci
src/gz barrier_breaker_management http://downloads.openwrt.org/barrier_br … management
src/gz barrier_breaker_oldpackages http://downloads.openwrt.org/barrier_br … ldpackages
src/gz barrier_breaker_packages http://downloads.openwrt.org/barrier_br … s/packages
src/gz barrier_breaker_routing http://downloads.openwrt.org/barrier_br … es/routing
src/gz barrier_breaker_telephony http://downloads.openwrt.org/barrier_br … /telephony
src/gz eko1 http://dl.eko.one.pl/barrier_breaker/ar71xx/packages
posiadam BB Luci, po wpisaniu polecenia blkid
dostaję odpowiedz -ash: blkid: not found - jak mogę doinstalować komendę lub jak inaczej sprawdzić UUID dysku?
Jak podłączyć dysk sformatowany na ntfs?
w Luci jest pakiet ntfs-3g ale w części Punkty montowania - Wpis montownia w opcji system plików wybieram fuseblk.
w części Punkty montowania mam urządzenie skonfigurowane jako:
/dev/sda6 (2750 MB) /mnt/sda6 fuseblk defaults nie tak ale już w części Zamontowane systemy plików już go nie widzę.
Tak, robiłem opkg update
Chcę na routerze uruchomić USBIP i dlna. Na forum jest informacja, że Gargulec nie jest już wspierany.
Więc zmieniłem firmware na BB Luci - czy tutaj tez działa USBIP?
Jak je zainstalować? Po wpisaniu opkg install kmod-usbip-server dostaje komunikat o braku pakietu.
Działa dziękuję.
Mam jeszcze pytanie czy na BB Luci można zainstalować lub uruchomić dlna?
Uruchomiłem overlay - przynajmniej tak mi się wydaje, bo w zakładce "punkty montowania" mam napisane:
overlayfs:/overlay / 468.89 MB / 475.22 MB 0% (2.33 MB).
Jak robię zgodnie z opisem na http://eko.one.pl/?p=openwrt-dlna to nie działa.
wpisuję najpierw: opkg update
następnie: opkg install minidlna
dostaję komunikat:
root@OpenWrt:~# opkg install minidlna
Unknown package 'minidlna'.
Collected errors:
* opkg_install_cmd: Cannot install package minidlna.
Mam router TP-Link TL-WDR3600 v1 na którym dzisiaj chciałem zainstalować OpenWrt z Luci.
Wszystko szło dobrze.
Następnie chciałem zrobić exroota i postępując zgodnie z opisem na eko.one.pl coś musiałem zrobić źle.
Teraz nie mogę już niczego skonfigurować.
Mogę zalogować się na router przez www w interface Luci, ale praktycznie nic nie działa
Nie mogę się podłączyć przez putty (po wpisaniu loginu i hasła putty zamyka się) analogicznie jest przez WinSCP.
Próbowałem ponownie wgrać firmware przez interface www, ale dostaje komunikat, że:
Przesłany plik obrazu nie zawiera obsługiwanego formatu. Upewnij się, że wybrałeś odpowiedni format obrazu dla danej platformy.
jak próbuję wyświetlić opcję punkty montowania dostaję komunikat:
Failed to execute cbi dispatcher target for entry '/admin/system/fstab'.
The called action terminated with an exception:
attempt to use a closed file
stack traceback:
[C]: in function 'assert'
?: in function 'dispatch'
?: in function <?:194>
w opcji skrypty startowe - wszystkie pozycje mają status wyłączony i nie mogę żadnego uruchomić.
eko.one.pl → Posty przez bartwr
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc