Na LUCI ustawiłem tylko lokalny adres na 192.168.8.2, podpiąłem kabel ethernetowy z głównego rutera do portu LAN, wyłączyłem DHCP oraz włączyłem WiFi. Urządzenia łączą się za pomocą WiFi i są w jednej puli adresów, co było założeniem.
Natomiast jak zmieniam przekierowania portów na głównym ruterze na odpowiednie IP w sieci LAN, to urządzenia za tym ruterem z LUCI nie są widoczne. Inne urządzenia, które są podpięte do głównego rutera są widoczne z zewnątrz, np. port 85 z zewnątrz jest przekierowywany na port 82 na 192.168.8.60.
Przekierowania na głównym ruterze robiłem wpisując adresy końcowe IP (nie robiąc nic więcej na ruterze z LUCI) i to nie działa, czy powinienem przekierować porty, które mnie interesują na adres tego rutera czyli 192.168.8.2 i na nim dopiero przekierować na odpowiednie adresy IP?
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
Opcje wyszukiwania (Strona 1 z 2)
eko.one.pl → Posty przez superprzemo
Znalezione posty: 1 do 25 z 33
1 2022-08-16 11:52:45
Odp: Ruter jako "punkt dostępowy" (8 odpowiedzi, napisanych Oprogramowanie / Software)
2 2022-08-16 07:03:38
Odp: Ruter jako "punkt dostępowy" (8 odpowiedzi, napisanych Oprogramowanie / Software)
Ja zapinałem złącza przelotowe, mam teraz prędkości 1000Mb/s, więc jest ok. Wszystko prawie działa według założeń, oprócz tego nie nie mogę się dostać do urządzeń za tym ruterem z zewnątrz mimo przekierowania portów na odpowiednie IP na głównym ruterze. Po LAN wszystko ładnie śmiga (mogę wchodzić na wszystkie urządzenia), tylko z zewnątrz nie można się dostać do odpowiednich urządzeń za tym ruterem.
Muszę dodać jakąś regułę żeby przekierowanie portów z zewnątrz działało?
3 2022-08-02 11:45:01
Odp: Ruter jako "punkt dostępowy" (8 odpowiedzi, napisanych Oprogramowanie / Software)
Dzięki za odpowiedzi, na pewno przetestuję.
Połączenie LAN z AX50 do WAN w Archer C7 jest za pomocą 100 metrowej skrętki cat 7. Na początku ustawiana jest prędkość 1GB/s a po jakimś czasie spada do 100MB/s. Na innych ruterach też tak się dzieje, na początku jest 1GB/s a potem spada do 100MB/s. W głównym ruterze ustawione jest bez negocjacji na 1GB/s po LAN.
Myślałem że da się jakoś "wymusić" stałą prędkość, żeby po czasie nie zwalniało do 100MB/s.
4 2022-08-02 10:09:45
Temat: Ruter jako "punkt dostępowy" (8 odpowiedzi, napisanych Oprogramowanie / Software)
Witam,
Proszę o pomoc w konfiguracji rutera z OPENWRT (luci).
Mam pierwszy ruter Tp-link AX50 (bez OPENWRT), który pracuje jako główny ruter podpięty przez WAN do neta. Pracuje on w sieci lokalnej 192.168.8.x oraz przedziela on adresy DHCP.
Drugi ruter Archer C7 (z Luci) podpięty jest do głównego rutera przez WAN i tutaj zaczynają się schody. Próbuję ustawić drugi ruter jako podrzędny, czyli żeby miał tą samą klasę adresów co główny czyli 192.168.8.x, miał wyłączony DHCP (adresy przyznawane przez główny ruter), oraz żeby można się było do niego dostać z zewnątrz i po sieci lokalnej rozgłaszanej po WiFi oraz LAN.
W oryginalnym sofcie wystarczy ustawić tryb pracy na „Punkt dostępowy” ale chcę to samo uzyskać na OPENWRT.
Walczę od kilku dni i nie jestem w stanie uzyskać takiego efektu. Jak najprościej ustawić taką konfigurację?
Drugie pytanie, czy można na stałe ustawić wymuszenie prędkości 1GB/s na porcie WAN?
5 2020-09-23 19:15:00
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Faktycznie, po zmianie na kanał 36 zamiast AUTO, sieć 5GHz ruszyła.
Wielkie dzięki za pomoc.
6 2020-09-23 18:06:47
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
root@Gargoyle:~# iw dev
phy#1
Interface wlan1
ifindex 11
wdev 0x100000002
addr 1c:3b:f3:4f:f6:c3
ssid makapaka_ext
type AP
channel 1 (2412 MHz), width: 40 MHz, center1: 2422 MHz
txpower 20.00 dBm
phy#0
Interface wlan0-1
ifindex 13
wdev 0x3
addr 1e:3b:f3:4f:f6:c2
type AP
txpower 0.00 dBm
Interface wlan0
ifindex 12
wdev 0x2
addr 1c:3b:f3:4f:f6:c2
ssid makapaka 5G
type managed
channel 48 (5240 MHz), width: 80 MHz, center1: 5210 MHz
txpower 20.00 dBm
root@Gargoyle:~# logread
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.000000] Linux version 4.9.219 (cezary@eko.one.pl) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7865-5880dd48d5) ) #0 Thu Apr 16 11:24:54 2020
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.000000] MyLoader: sysp=8520fd77, boardp=a649308a, parts=182a8a29
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] bootconsole [early0] enabled
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Determined physical RAM map:
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] memory: 08000000 @ 00000000 (usable)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Zone ranges:
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Movable zone start for each node
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Early memory node ranges
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.000000] On node 0 totalpages: 32768
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 804505d4, node_mem_map 81000020
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.000000] Normal zone: 256 pages used for memmap
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.000000] Kernel command line: board=ARCHER-C7-V5 mtdparts=spi0.0:128k(factory-uboot)ro,128k(u-boot)ro,64k@0x50000(art)ro,128k@0x60000(info)ro,1536k@0xc0000(kernel),13824k(rootfs),15360k@0xc0000(firmware) console=ttyS0,115200 rootfstype=squashfs noinitrd
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Memory: 124940K/131072K available (3413K kernel code, 174K rwdata, 448K rodata, 308K init, 211K bss, 6132K reserved, 0K cma-reserved)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] NR_IRQS:51
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.008225] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.071042] pid_max: default: 32768 minimum: 301
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.075994] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.082974] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.092712] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.103120] futex hash table entries: 256 (order: -1, 3072 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.110603] NET: Registered protocol family 16
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.116611] MIPS: machine is TP-LINK Archer C7 v5
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 0.124327] registering PCI controller with io_map_base unset
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.379795] PCI host bridge to bus 0000:00
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.384164] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff]
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.391402] pci_bus 0000:00: root bus resource [io 0x0001]
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.397277] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.404424] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.412804] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.412842] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.412890] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.412954] pci 0000:00:00.0: supports D1 D2
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.413131] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.413153] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.420873] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref]
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.428514] pci 0000:00:00.0: using irq 40 for pin 1
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.436540] clocksource: Switched to clocksource MIPS
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.442807] NET: Registered protocol family 2
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.448202] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.455555] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.462305] TCP: Hash tables configured (established 1024 bind 1024)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.469089] UDP hash table entries: 256 (order: 0, 4096 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.475255] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.482113] NET: Registered protocol family 1
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 0.486767] PCI: CLS 0 bytes, default 32
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 0.489226] Crashlog allocated RAM at address 0x3f00000
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.495681] workingset: timestamp_bits=30 max_order=15 bucket_order=0
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.508081] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.514227] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.532741] io scheduler noop registered
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.536915] io scheduler deadline registered (default)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.542698] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.551633] console [ttyS0] disabled
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.575472] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.584574] console [ttyS0] enabled
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.592132] bootconsole [early0] disabled
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 0.605970] m25p80 spi0.0: found w25q128, expected m25p80
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.621093] m25p80 spi0.0: w25q128 (16384 Kbytes)
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.625987] 7 cmdlinepart partitions found on MTD device spi0.0
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.632116] Creating 7 MTD partitions on "spi0.0":
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.637086] 0x000000000000-0x000000020000 : "factory-uboot"
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.644456] 0x000000020000-0x000000040000 : "u-boot"
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.651341] 0x000000050000-0x000000060000 : "art"
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.657936] 0x000000060000-0x000000080000 : "info"
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.664596] 0x0000000c0000-0x000000240000 : "kernel"
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.671479] 0x000000240000-0x000000fc0000 : "rootfs"
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.677999] mtd: device 5 (rootfs) set to be root filesystem
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.683895] 1 squashfs-split partitions found on MTD device rootfs
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.690327] 0x000000840000-0x000000fc0000 : "rootfs_data"
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 0.697752] 0x0000000c0000-0x000000fc0000 : "firmware"
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.705614] libphy: Fixed MDIO Bus: probed
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 0.726299] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 1.443740] libphy: ag71xx_mdio: probed
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 2.078159] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 2.089725] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:SGMII
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 2.098300] NET: Registered protocol family 10
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 2.107055] NET: Registered protocol family 17
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 2.111689] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 2.125187] 8021q: 802.1Q VLAN Support v1.8
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 2.131125] hctosys: unable to open rtc device (rtc0)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 2.140721] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 2.149715] Freeing unused kernel memory: 308K
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 2.154306] This architecture does not have kernel memory protection.
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 2.576555] random: fast init done
Wed Sep 23 18:55:59 2020 user.info kernel: [ 2.753575] init: Console is alive
Wed Sep 23 18:55:59 2020 user.info kernel: [ 2.757332] init: - watchdog -
Wed Sep 23 18:55:59 2020 user.info kernel: [ 4.955728] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.188900] usbcore: registered new interface driver usbfs
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.194658] usbcore: registered new interface driver hub
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.200263] usbcore: registered new device driver usb
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.234674] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 5.249168] SCSI subsystem initialized
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.257605] ehci-platform: EHCI generic platform driver
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.263076] ehci-platform ehci-platform.0: EHCI Host Controller
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.269263] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.279701] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.306569] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.313928] hub 1-0:1.0: USB hub found
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.318197] hub 1-0:1.0: 1 port detected
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.322550] ehci-platform ehci-platform.1: EHCI Host Controller
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.328735] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.339190] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.366550] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.373904] hub 2-0:1.0: USB hub found
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.378176] hub 2-0:1.0: 1 port detected
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.386101] usbcore: registered new interface driver usb-storage
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 5.394177] usbcore: registered new interface driver uas
Wed Sep 23 18:55:59 2020 user.info kernel: [ 5.400340] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Wed Sep 23 18:55:59 2020 user.info kernel: [ 5.418214] init: - preinit -
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 6.600451] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 6.633496] random: procd: uninitialized urandom read (4 bytes read)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 7.648186] eth0: link up (1000Mbps/Full duplex)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 7.653158] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Wed Sep 23 18:55:59 2020 user.info kernel: [ 9.845937] mount_root: loading kmods from internal overlay
Wed Sep 23 18:55:59 2020 user.info kernel: [ 9.941672] kmodloader: loading kernel modules from //etc/modules-boot.d/*
Wed Sep 23 18:55:59 2020 user.info kernel: [ 9.950513] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 10.908662] jffs2: notice: (489) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Wed Sep 23 18:55:59 2020 user.info kernel: [ 10.925070] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Wed Sep 23 18:55:59 2020 user.info kernel: [ 10.936332] block: extroot: not configured
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 11.011898] jffs2: notice: (486) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Wed Sep 23 18:55:59 2020 user.info kernel: [ 11.028831] mount_root: loading kmods from internal overlay
Wed Sep 23 18:55:59 2020 user.info kernel: [ 11.095601] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
Wed Sep 23 18:55:59 2020 user.info kernel: [ 11.106615] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
Wed Sep 23 18:55:59 2020 user.info kernel: [ 11.662538] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Wed Sep 23 18:55:59 2020 user.info kernel: [ 11.672330] block: extroot: not configured
Wed Sep 23 18:55:59 2020 user.info kernel: [ 11.677603] mount_root: switching to jffs2 overlay
Wed Sep 23 18:55:59 2020 user.warn kernel: [ 11.749640] urandom-seed: Seeding with /etc/urandom.seed
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 11.880695] eth0: link down
Wed Sep 23 18:55:59 2020 user.info kernel: [ 11.893710] procd: - early -
Wed Sep 23 18:55:59 2020 user.info kernel: [ 11.897369] procd: - watchdog -
Wed Sep 23 18:55:59 2020 user.info kernel: [ 12.610975] procd: - watchdog -
Wed Sep 23 18:55:59 2020 user.info kernel: [ 12.614442] procd: - ubus -
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 12.683452] random: jshn: uninitialized urandom read (4 bytes read)
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 12.799613] random: ubusd: uninitialized urandom read (4 bytes read)
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 12.811540] random: ubusd: uninitialized urandom read (4 bytes read)
Wed Sep 23 18:55:59 2020 user.info kernel: [ 12.819910] procd: - init -
Wed Sep 23 18:55:59 2020 user.info kernel: [ 13.721395] kmodloader: loading kernel modules from /etc/modules.d/*
Wed Sep 23 18:55:59 2020 kern.notice kernel: [ 13.859979] Key type dns_resolver registered
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 13.887007] RPC: Registered named UNIX socket transport module.
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 13.893124] RPC: Registered udp transport module.
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 13.898025] RPC: Registered tcp transport module.
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 13.902881] RPC: Registered tcp NFSv4.1 backchannel transport module.
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 13.929771] tun: Universal TUN/TAP device driver, 1.6
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 13.934995] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 13.953893] gre: GRE over IPv4 demultiplexor driver
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 13.961062] ip_gre: GRE over IPv4 tunneling driver
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.003687] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.037763] u32 classifier
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.040561] input device check on
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.044341] Actions configured
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.069000] Mirror/redirect action on
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.112879] fuse init (API version 7.26)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.125570] usbcore: registered new interface driver cdc_acm
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.131466] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.148442] usbcore: registered new interface driver cdc_wdm
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.156237] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.164557] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.183605] Ebtables v2.0 registered
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.189795] ip_tables: (C) 2000-2006 Netfilter Core Team
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.212112] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.490731] usbcore: registered new interface driver ums-alauda
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.506940] usbcore: registered new interface driver ums-cypress
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.528689] usbcore: registered new interface driver ums-datafab
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.544204] usbcore: registered new interface driver ums-freecom
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.568570] usbcore: registered new interface driver ums-isd200
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.588769] usbcore: registered new interface driver ums-jumpshot
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.598669] usbcore: registered new interface driver ums-karma
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.613051] usbcore: registered new interface driver ums-sddr09
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.634470] usbcore: registered new interface driver ums-sddr55
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.658984] usbcore: registered new interface driver ums-usbat
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.668393] usbcore: registered new interface driver usblp
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.706345] usbcore: registered new interface driver usbserial
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.712531] usbcore: registered new interface driver usbserial_generic
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.719379] usbserial: USB Serial support registered for generic
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.874738] xt_time: kernel timezone is -0000
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.890646] usbcore: registered new interface driver cdc_ether
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 14.937962] usbcore: registered new interface driver cdc_ncm
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.269561] usbcore: registered new interface driver huawei_cdc_ncm
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.388531] PPP generic driver version 2.4.2
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.408097] NET: Registered protocol family 24
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.417998] PPTP driver version 0.8.5
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.431453] usbcore: registered new interface driver qmi_wwan
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.449906] usbcore: registered new interface driver rndis_host
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.469789] usbcore: registered new interface driver sierra
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.475624] usbserial: USB Serial support registered for Sierra USB modem
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.508940] usbcore: registered new interface driver sierra_net
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 15.587269] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 15.593274] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 15.896965] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 15.908054] ath10k_pci 0000:00:00.0: Falling back to user helper
Wed Sep 23 18:55:59 2020 kern.err kernel: [ 17.564228] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 17.574846] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 17.585937] ath10k_pci 0000:00:00.0: Falling back to user helper
Wed Sep 23 18:55:59 2020 kern.err kernel: [ 17.719830] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 17.734074] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 17.743646] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 17.756660] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00037 api 5 features no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 a4a52adb
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 17.851458] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
Wed Sep 23 18:55:59 2020 kern.warn kernel: [ 17.862293] ath10k_pci 0000:00:00.0: Falling back to user helper
Wed Sep 23 18:55:59 2020 kern.err kernel: [ 17.934547] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 17.954048] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 19.071381] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.208112] ath: EEPROM regdomain: 0x0
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.208118] ath: EEPROM indicates default country code should be used
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.208121] ath: doing EEPROM country->regdmn map search
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.208133] ath: country maps to regdmn code: 0x3a
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.208137] ath: Country alpha2 being used: US
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.208140] ath: Regpair used: 0x3a
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 19.318437] usbcore: registered new interface driver cdc_mbim
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 19.327142] usbcore: registered new interface driver option
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 19.332970] usbserial: USB Serial support registered for GSM modem (1-port)
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 19.347960] usbcore: registered new interface driver qcserial
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 19.353974] usbserial: USB Serial support registered for Qualcomm USB modem
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.403618] ath: EEPROM regdomain: 0x0
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.403625] ath: EEPROM indicates default country code should be used
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.403628] ath: doing EEPROM country->regdmn map search
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.403641] ath: country maps to regdmn code: 0x3a
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.403645] ath: Country alpha2 being used: US
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.403647] ath: Regpair used: 0x3a
Wed Sep 23 18:55:59 2020 kern.debug kernel: [ 19.414121] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Wed Sep 23 18:55:59 2020 kern.info kernel: [ 19.417824] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=47
Wed Sep 23 18:55:59 2020 user.info kernel: [ 19.475377] kmodloader: done loading kernel modules from /etc/modules.d/*
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain free.aero2.net.pl
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .bit
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .glue
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .parody
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .dyn
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .bbs
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .free
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .fur
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .geek
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .gopher
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .indy
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .ing
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .null
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .oss
Wed Sep 23 18:56:00 2020 user.notice dnsmasq: Allowing RFC1918 responses for domain .micro
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: started, version 2.80 cachesize 150
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: DNS service limited to local subnets
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC no-ID loop-detect inotify dumpfile
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using local addresses only for domain test
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using local addresses only for domain onion
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using local addresses only for domain localhost
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using local addresses only for domain local
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using local addresses only for domain invalid
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using local addresses only for domain bind
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain micro
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain micro
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain micro
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain oss
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain oss
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain oss
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain null
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain null
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain null
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain ing
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain ing
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain ing
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain indy
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain indy
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain indy
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain gopher
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain gopher
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain gopher
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain geek
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain geek
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain geek
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain fur
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain fur
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain fur
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain free
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain free
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain free
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain bbs
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain bbs
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain bbs
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: using 12 more nameservers
Wed Sep 23 18:56:01 2020 daemon.warn dnsmasq[1454]: no servers found in /tmp/resolv.conf.auto, will retry
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: read /etc/hosts - 5 addresses
Wed Sep 23 18:56:01 2020 daemon.info dnsmasq[1454]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses
Wed Sep 23 18:56:01 2020 authpriv.info dropbear[1481]: Not backgrounding
Wed Sep 23 18:56:04 2020 user.notice : Added device handler type: tunnel
Wed Sep 23 18:56:04 2020 user.notice : Added device handler type: Network device
Wed Sep 23 18:56:04 2020 user.notice : Added device handler type: bridge
Wed Sep 23 18:56:04 2020 user.notice : Added device handler type: veth
Wed Sep 23 18:56:04 2020 user.notice : Added device handler type: macvlan
Wed Sep 23 18:56:04 2020 user.notice : Added device handler type: 8021ad
Wed Sep 23 18:56:04 2020 user.notice : Added device handler type: 8021q
Wed Sep 23 18:56:06 2020 daemon.err block: /dev/mtdblock5 is already mounted on /rom
Wed Sep 23 18:56:06 2020 daemon.err block: /dev/mtdblock6 is already mounted on /overlay
Wed Sep 23 18:56:08 2020 kern.info kernel: [ 29.859393] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Wed Sep 23 18:56:08 2020 kern.info kernel: [ 29.880612] br-lan: port 1(eth0.1) entered blocking state
Wed Sep 23 18:56:08 2020 kern.info kernel: [ 29.886199] br-lan: port 1(eth0.1) entered disabled state
Wed Sep 23 18:56:08 2020 kern.info kernel: [ 29.892138] device eth0.1 entered promiscuous mode
Wed Sep 23 18:56:08 2020 kern.info kernel: [ 29.897123] device eth0 entered promiscuous mode
Wed Sep 23 18:56:08 2020 daemon.notice netifd: Interface 'lan' is enabled
Wed Sep 23 18:56:08 2020 kern.info kernel: [ 29.928783] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Wed Sep 23 18:56:08 2020 daemon.notice netifd: Interface 'lan' is setting up now
Wed Sep 23 18:56:08 2020 daemon.notice netifd: Interface 'lan' is now up
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: reading /tmp/resolv.conf.auto
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using local addresses only for domain test
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using local addresses only for domain onion
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using local addresses only for domain localhost
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using local addresses only for domain local
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using local addresses only for domain invalid
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using local addresses only for domain bind
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain micro
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain micro
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain micro
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain oss
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain oss
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain oss
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain null
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain null
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain null
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain ing
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain ing
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain ing
Wed Sep 23 18:56:08 2020 daemon.notice netifd: Interface 'loopback' is enabled
Wed Sep 23 18:56:08 2020 daemon.notice netifd: Interface 'loopback' is setting up now
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain indy
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain indy
Wed Sep 23 18:56:08 2020 daemon.notice netifd: Interface 'loopback' is now up
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain indy
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain gopher
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain gopher
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain gopher
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain geek
Wed Sep 23 18:56:08 2020 daemon.notice netifd: Interface 'wan6' is enabled
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain geek
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain geek
Wed Sep 23 18:56:08 2020 kern.info kernel: [ 30.009185] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain fur
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain fur
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain fur
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain free
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain free
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain free
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain bbs
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain bbs
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain bbs
Wed Sep 23 18:56:08 2020 daemon.info dnsmasq[1454]: using 13 more nameservers
Wed Sep 23 18:56:08 2020 daemon.notice netifd: Network device 'lo' link is up
Wed Sep 23 18:56:08 2020 daemon.notice netifd: Interface 'loopback' has link connectivity
Wed Sep 23 18:56:09 2020 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Wed Sep 23 18:56:09 2020 kern.info kernel: [ 31.206208] eth0: link up (1000Mbps/Full duplex)
Wed Sep 23 18:56:09 2020 daemon.notice netifd: Network device 'eth0' link is up
Wed Sep 23 18:56:09 2020 kern.info kernel: [ 31.236682] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Wed Sep 23 18:56:09 2020 kern.info kernel: [ 31.266782] br-lan: port 1(eth0.1) entered blocking state
Wed Sep 23 18:56:09 2020 kern.info kernel: [ 31.272367] br-lan: port 1(eth0.1) entered forwarding state
Wed Sep 23 18:56:09 2020 kern.info kernel: [ 31.278281] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
Wed Sep 23 18:56:09 2020 daemon.notice netifd: VLAN 'eth0.1' link is up
Wed Sep 23 18:56:09 2020 daemon.notice netifd: VLAN 'eth0.2' link is up
Wed Sep 23 18:56:09 2020 daemon.notice netifd: Interface 'wan6' has link connectivity
Wed Sep 23 18:56:09 2020 daemon.notice netifd: Interface 'wan6' is setting up now
Wed Sep 23 18:56:09 2020 daemon.notice netifd: Interface 'wan6' is now up
Wed Sep 23 18:56:09 2020 daemon.notice netifd: bridge 'br-lan' link is up
Wed Sep 23 18:56:09 2020 daemon.notice netifd: Interface 'lan' has link connectivity
Wed Sep 23 18:56:09 2020 kern.info kernel: [ 31.396628] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344054] ath: EEPROM regdomain: 0x809e
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344061] ath: EEPROM indicates we should expect a country code
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344067] ath: doing EEPROM country->regdmn map search
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344072] ath: country maps to regdmn code: 0x50
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344077] ath: Country alpha2 being used: PL
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344080] ath: Regpair used: 0x50
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344085] ath: regdomain 0x809e dynamically updated by user
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344166] ath: EEPROM regdomain: 0x809e
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344169] ath: EEPROM indicates we should expect a country code
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344173] ath: doing EEPROM country->regdmn map search
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344178] ath: country maps to regdmn code: 0x50
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344181] ath: Country alpha2 being used: PL
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344184] ath: Regpair used: 0x50
Wed Sep 23 18:56:10 2020 kern.debug kernel: [ 32.344187] ath: regdomain 0x809e dynamically updated by user
Wed Sep 23 18:56:10 2020 user.notice mac80211: Failed command: iw phy phy1 set antenna all all
Wed Sep 23 18:56:11 2020 user.notice mac80211: Failed command: iw phy phy0 set antenna all all
Wed Sep 23 18:56:13 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy1.conf
Wed Sep 23 18:56:13 2020 kern.info kernel: [ 34.635001] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
Wed Sep 23 18:56:13 2020 kern.info kernel: [ 34.736246] br-lan: port 2(wlan1) entered blocking state
Wed Sep 23 18:56:13 2020 kern.info kernel: [ 34.741789] br-lan: port 2(wlan1) entered disabled state
Wed Sep 23 18:56:13 2020 kern.info kernel: [ 34.747713] device wlan1 entered promiscuous mode
Wed Sep 23 18:56:13 2020 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Sep 23 18:56:13 2020 daemon.err hostapd: Using interface wlan1 with hwaddr 1c:3b:f3:4f:f6:c3 and ssid "xxx"
Wed Sep 23 18:56:13 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Wed Sep 23 18:56:16 2020 kern.info kernel: [ 37.553929] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
Wed Sep 23 18:56:16 2020 kern.info kernel: [ 37.578891] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
Wed Sep 23 18:56:16 2020 kern.info kernel: [ 37.585584] br-lan: port 2(wlan1) entered blocking state
Wed Sep 23 18:56:16 2020 kern.info kernel: [ 37.591126] br-lan: port 2(wlan1) entered forwarding state
Wed Sep 23 18:56:16 2020 kern.info kernel: [ 37.604482] br-lan: port 3(wlan0-1) entered blocking state
Wed Sep 23 18:56:16 2020 kern.info kernel: [ 37.610324] br-lan: port 3(wlan0-1) entered disabled state
Wed Sep 23 18:56:16 2020 kern.info kernel: [ 37.616337] device wlan0-1 entered promiscuous mode
Wed Sep 23 18:56:16 2020 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED
Wed Sep 23 18:56:16 2020 daemon.notice hostapd: wlan1: AP-ENABLED
Wed Sep 23 18:56:16 2020 daemon.notice hostapd: wlan0-1: interface state UNINITIALIZED->COUNTRY_UPDATE
Wed Sep 23 18:56:16 2020 daemon.notice hostapd: ACS: Automatic channel selection started, this may take a bit
Wed Sep 23 18:56:16 2020 daemon.notice hostapd: wlan0-1: interface state COUNTRY_UPDATE->ACS
Wed Sep 23 18:56:16 2020 daemon.notice hostapd: wlan0-1: ACS-STARTED
Wed Sep 23 18:56:16 2020 user.err : error starting threads: errno 89 (Function not implemented)
Wed Sep 23 18:56:16 2020 daemon.notice netifd: Network device 'wlan1' link is up
Wed Sep 23 18:56:16 2020 daemon.notice procd: /etc/rc.d/S60nfsd: exportfs: could not open /var/lib/nfs/.etab.lock for locking: errno 2 (No such file or directory)
Wed Sep 23 18:56:16 2020 daemon.notice procd: /etc/rc.d/S60nfsd: exportfs: can't lock /var/lib/nfs/etab for writing
Wed Sep 23 18:56:16 2020 daemon.notice procd: /etc/rc.d/S60nfsd: exportfs: could not open /var/lib/nfs/.xtab.lock for locking: errno 2 (No such file or directory)
Wed Sep 23 18:56:16 2020 daemon.notice procd: /etc/rc.d/S60nfsd: exportfs: can't lock /var/lib/nfs/xtab for writing
Wed Sep 23 18:56:16 2020 daemon.notice procd: /etc/rc.d/S60nfsd: Command failed: Not found
Wed Sep 23 18:56:17 2020 daemon.notice procd: /etc/rc.d/S90ddns_gargoyle: ERROR: No valid dynamic DNS service configurations defined
Wed Sep 23 18:56:17 2020 daemon.notice procd: /etc/rc.d/S90ddns_gargoyle: (Did you specify correct configuration file path?)
Wed Sep 23 18:56:28 2020 kern.warn kernel: [ 49.883618] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
Wed Sep 23 18:56:28 2020 kern.warn kernel: [ 49.890948] old minutes west=0, new minutes west=-120
Wed Sep 23 18:56:34 2020 daemon.notice hostapd: wlan0-1: ACS-COMPLETED freq=5745 channel=149
Wed Sep 23 18:56:34 2020 daemon.err hostapd: Using interface wlan0-1 with hwaddr 1e:3b:f3:4f:f6:c2 and ssid "xxx"
Wed Sep 23 18:56:34 2020 daemon.notice hostapd: wlan0-1: interface state ACS->ENABLED
Wed Sep 23 18:56:34 2020 daemon.notice hostapd: wlan0-1: AP-ENABLED
Wed Sep 23 18:56:34 2020 kern.info kernel: [ 56.110641] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Wed Sep 23 18:56:34 2020 daemon.notice netifd: radio0 (1701): Successfully initialized wpa_supplicant
Wed Sep 23 18:56:35 2020 daemon.notice netifd: Interface 'wwan' is enabled
Wed Sep 23 18:56:36 2020 kern.info kernel: [ 57.768535] wlan0: authenticate with d8:47:32:31:e9:72
Wed Sep 23 18:56:36 2020 kern.info kernel: [ 57.773947] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
Wed Sep 23 18:56:36 2020 kern.info kernel: [ 57.789954] wlan0: send auth to d8:47:32:31:e9:72 (try 1/3)
Wed Sep 23 18:56:36 2020 kern.info kernel: [ 57.797623] wlan0: authenticated
Wed Sep 23 18:56:36 2020 kern.info kernel: [ 57.806731] wlan0: associate with d8:47:32:31:e9:72 (try 1/3)
Wed Sep 23 18:56:36 2020 daemon.notice netifd: Network device 'wlan0' link is up
Wed Sep 23 18:56:36 2020 daemon.notice netifd: Interface 'wwan' has link connectivity
Wed Sep 23 18:56:36 2020 daemon.notice netifd: Interface 'wwan' is setting up now
Wed Sep 23 18:56:36 2020 kern.info kernel: [ 57.818660] wlan0: RX AssocResp from d8:47:32:31:e9:72 (capab=0x1511 status=0 aid=1)
Wed Sep 23 18:56:36 2020 kern.info kernel: [ 57.828324] wlan0: associated
Wed Sep 23 18:56:36 2020 kern.info kernel: [ 57.840786] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Wed Sep 23 18:56:36 2020 kern.debug kernel: [ 57.849195] wlan0: Limiting TX power to 20 (23 - 3) dBm as advertised by d8:47:32:31:e9:72
Wed Sep 23 18:56:36 2020 daemon.notice netifd: wwan (2680): udhcpc: started, v1.28.4
Wed Sep 23 18:56:36 2020 daemon.notice netifd: wwan (2680): udhcpc: sending discover
Wed Sep 23 18:56:36 2020 daemon.notice netifd: wwan (2680): udhcpc: sending select for 192.168.1.100
Wed Sep 23 18:56:36 2020 daemon.notice netifd: wwan (2680): udhcpc: lease of 192.168.1.100 obtained, lease time 2147483
Wed Sep 23 18:56:36 2020 daemon.notice netifd: Interface 'wwan' is now up
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: reading /tmp/resolv.conf.auto
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using local addresses only for domain test
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using local addresses only for domain onion
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using local addresses only for domain localhost
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using local addresses only for domain local
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using local addresses only for domain invalid
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using local addresses only for domain bind
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain micro
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain micro
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain micro
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain oss
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain oss
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain oss
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain null
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain null
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain null
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain ing
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain ing
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain ing
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain indy
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain indy
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain indy
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain gopher
Wed Sep 23 18:56:36 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain gopher
Wed Sep 23 18:56:36 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain gopher
Wed Sep 23 18:56:36 2020 daemon.err hostapd: Failed to set beacon parameters
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain geek
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain geek
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain geek
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain fur
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain fur
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain fur
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain free
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain free
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain free
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.142.171.235#53 for domain bbs
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 95.211.32.162#53 for domain bbs
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using nameserver 66.244.95.20#53 for domain bbs
Wed Sep 23 18:56:36 2020 daemon.info dnsmasq[1454]: using 15 more nameservers
Wed Sep 23 18:56:39 2020 authpriv.info dropbear[2750]: Child connection from 192.168.1.164:56683
Wed Sep 23 18:57:11 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:11 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:11 2020 daemon.err hostapd: Failed to set beacon parameters
Wed Sep 23 18:57:13 2020 user.notice root: vsftpd init: mounted = 0
Wed Sep 23 18:57:13 2020 daemon.notice procd: /etc/rc.d/S90vsftpd: ERROR: No drives attached, no directories to share!
Wed Sep 23 18:57:13 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led WLAN
Wed Sep 23 18:57:13 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led WLAN5G
Wed Sep 23 18:57:13 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led WAN
Wed Sep 23 18:57:13 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led LAN1
Wed Sep 23 18:57:13 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led LAN2
Wed Sep 23 18:57:13 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led LAN3
Wed Sep 23 18:57:13 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led LAN4
Wed Sep 23 18:57:13 2020 daemon.notice procd: /etc/rc.d/S96led: setting up led USB
Wed Sep 23 18:57:14 2020 daemon.info procd: - init complete -
Wed Sep 23 18:57:17 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:17 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:17 2020 daemon.err hostapd: Failed to set beacon parameters
Wed Sep 23 18:57:19 2020 authpriv.notice dropbear[2750]: Password auth succeeded for 'root' from 192.168.1.164:56683
Wed Sep 23 18:57:22 2020 kern.notice kernel: [ 73.236576] random: crng init done
Wed Sep 23 18:57:22 2020 kern.notice kernel: [ 73.240097] random: 6 urandom warning(s) missed due to ratelimiting
Wed Sep 23 18:57:23 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:23 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:23 2020 daemon.err hostapd: Failed to set beacon parameters
Wed Sep 23 18:57:29 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:29 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:29 2020 daemon.err hostapd: Failed to set beacon parameters
Wed Sep 23 18:57:33 2020 user.notice firewall: Reloading firewall due to ifup of wan6 (eth0.2)
Wed Sep 23 18:57:34 2020 user.notice firewall: Reloading firewall due to ifup of wwan (wlan0)
Wed Sep 23 18:57:35 2020 user.notice relayd: Assigning 192.168.1.100 to bridge interface
Wed Sep 23 18:57:35 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:35 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:35 2020 daemon.err hostapd: Failed to set beacon parameters
Wed Sep 23 18:57:35 2020 user.notice relayd: Reloading relayd due to ifup of wwan (wlan0)
Wed Sep 23 18:57:41 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:41 2020 daemon.warn hostapd: Failed to check if DFS is required; ret=-1
Wed Sep 23 18:57:41 2020 daemon.err hostapd: Failed to set beacon parameters
7 2020-09-23 17:27:47
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Archer C7 v5.
Próbowałem na Luci i Gargoyle, ale bez skutku.
8 2020-09-23 17:05:50
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Po kilku dniach pracy jako AP na 2.4GHz postanowiłem dodać jeszcze repeater na 5Ghz, dodałem AP według opisu i teraz moj konfig wireless tak wygląda:
config wifi-device 'radio0'
option type 'mac80211'
option hwmode '11a'
option path 'pci0000:00/0000:00:00.0'
option htmode 'VHT80'
option noscan '1'
option channel 'auto'
option country 'PL'
config wifi-device 'radio1'
option type 'mac80211'
option hwmode '11g'
option path 'platform/qca956x_wmac'
option noscan '1'
option channel '1'
option htmode 'HT40+'
option country 'PL'
config wifi-iface 'ap_g'
option device 'radio1'
option mode 'ap'
option network 'lan'
option disassoc_low_ack '0'
option ssid 'xxx'
option encryption 'psk2'
option key 'xxx'
config wifi-iface 'ap_a'
option device 'radio0'
option mode 'ap'
option network 'lan'
option disassoc_low_ack '0'
option ssid 'xxx'
option channel '36'
option encryption 'psk2'
option key 'xxx'
config wifi-iface
option device 'radio0'
option mode 'sta'
option ssid 'xxx'
option encryption 'psk2'
option key 'xxx'
option network 'wwan'Niestety sieć w 5GHz nie jest dostępna.
Radio na 5GHz poprawnie łaczy się z głównym ruterem, natomiast nie rozgłasza sieci.
Czy praca jednocześnie jako klient i AP wymaga jakiejś innej konfiguracji?
9 2020-09-02 22:23:21
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
A czy to się faktycznie zdarza się, że po włączeniu roamingu wifi, niektórzy klienci mają problemy z połączeniem do AP?
Czy ja coś znowu źle ustawiłem i powinno to działać bezproblemowo z każdym urządzeniem?
10 2020-09-02 22:09:10
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Włączyłem roaming w Gargoyle, ale starszy laptop i kilka innych urzadzeń nie chciało się wtedy połączyć z siecią (android połączył się bez problemu) i musiałem wyłaczyć ten tryb na ruterze.
Widzę że będę musiał zrezygnować z trybu roaming WiFi, bo mam kilkanaście urządzeń podłączonych do sieci 2GHz (komunikują się one z Domoticzem) i muszą pracować bezproblemowo.
Jak mam na drugim ruterze ustawioną taką samą nazwę sieci oraz hasło jak na głównym, to nie będzie to powodowało żadnych konfliktów?
11 2020-09-02 21:12:53
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Luci bez problemu to zapisało.
W Luci wpisze te dane, tylko jak mam je wpisać do Gargoyle?
Tam nie ma gdzie tych danych wpisać.
12 2020-09-02 20:38:07
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Jak zaznaczam tylko roaming w LEDE (wpad zainstalowany) i klikam żeby zapisać, to sieć 2GHz mi nie wstaje i mam takie logi
Wed Sep 2 21:25:00 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Wed Sep 2 21:25:00 2020 daemon.err hostapd: FT (IEEE 802.11r) requires nas_identifier to be configured as a 1..48 octet string
Wed Sep 2 21:25:00 2020 daemon.err hostapd: 1 errors found in configuration file '/var/run/hostapd-phy0.conf'
Wed Sep 2 21:25:00 2020 daemon.err hostapd: Failed to set up interface with /var/run/hostapd-phy0.conf
Wed Sep 2 21:25:00 2020 daemon.err hostapd: Failed to initialize interface
Wed Sep 2 21:25:00 2020 daemon.notice netifd: radio0 (6053): Device setup failed: HOSTAPD_START_FAILED
Wed Sep 2 21:25:01 2020 daemon.info odhcpd[1034]: Using a RA lifetime of 0 seconds on br-lan
Wed Sep 2 21:25:10 2020 daemon.notice netifd: radio0 (6385): sh: acs_survey: out of range
Wed Sep 2 21:25:11 2020 daemon.err hostapd: Configuration file: /var/run/hostapd-phy0.conf
Wed Sep 2 21:25:11 2020 daemon.err hostapd: FT (IEEE 802.11r) requires nas_identifier to be configured as a 1..48 octet string
Wed Sep 2 21:25:11 2020 daemon.err hostapd: 1 errors found in configuration file '/var/run/hostapd-phy0.conf'
Wed Sep 2 21:25:11 2020 daemon.err hostapd: Failed to set up interface with /var/run/hostapd-phy0.conf
Wed Sep 2 21:25:11 2020 daemon.err hostapd: Failed to initialize interface
Wed Sep 2 21:25:11 2020 daemon.notice netifd: radio0 (6385): Device setup failed: HOSTAPD_START_FAILEDbyCo ja mam jeszcze powpisywać w okienka, które się pojawiły po zaznaczeniu roaming?
13 2020-09-02 19:47:03
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Ok, konfiguracja poszła od nowa przez terminal i most między siecią 5GHz a 2GHz działa (dzięki poradnikowi Cezarego).
Teraz pora na włączenie roamingu wifi między ruterami.
Czy uruchamia się go na obu ruterach, czy tylko na tym 2-gim rozgłaszającym?
Ustawia się to w GUI, czy też trzeba dopisać coś w konfigu?
14 2020-09-01 17:21:51
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Faktycznie zacząłem od d... strony, poniżej moje wczorajsze wypociny (teraz ruter nie chce się łączyć jako klient z siecią 5GHz):
network:
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config globals 'globals'
option ula_prefix 'fdeb:ac98:5520::/48'
config interface 'lan'
option type 'bridge'
option proto 'static'
option netmask '255.255.255.0'
option ip6assign '60'
option ipaddr '192.168.2.1'
option gateway '192.168.1.1'
option dns '192.168.1.1'
option _orig_ifname 'eth0.1'
option _orig_bridge 'true'
option ifname 'eth0 eth0.1 eth0.2'
config switch
option name 'switch0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'switch0'
option vlan '1'
option ports '2 3 4 5 0t'
config switch_vlan
option device 'switch0'
option vlan '2'
option ports '1 0t'
config interface 'wwan'
option type 'bridge'
option _orig_ifname 'wlan0 wlan1'
option _orig_bridge 'true'
option ifname 'eth0 eth0.1 eth0.2'
option proto 'static'
option ipaddr '192.168.1.245'
option netmask '255.255.255.0'
option gateway '192.168.1.1'
option dns '192.168.1.1'
config interface 'repeater_most'
option proto 'relay'
option ipaddr '192.168.1.244'
list network 'lan'
list network 'wwan'
config interface 'wwan1'
option proto 'dhcp'
option type 'bridge'
option stp '1'
option _orig_ifname 'wlan1-1'
option _orig_bridge 'true'
option ifname 'br-wwan eth0 eth0.1 eth0.2'dhcp:
config dnsmasq
option domainneeded '1'
option boguspriv '1'
option filterwin2k '0'
option localise_queries '1'
option rebind_protection '1'
option rebind_localhost '1'
option local '/lan/'
option domain 'lan'
option expandhosts '1'
option nonegcache '0'
option authoritative '1'
option readethers '1'
option leasefile '/tmp/dhcp.leases'
option resolvfile '/tmp/resolv.conf.auto'
option localservice '1'
list rebind_domain 'free.aero2.net.pl'
config dhcp 'lan'
option interface 'lan'
option ignore '1'
option ra 'relay'
config dhcp 'wan'
option interface 'wan'
option ignore '1'
config odhcpd 'odhcpd'
option maindhcp '0'
option leasefile '/tmp/hosts/odhcpd'
option leasetrigger '/usr/sbin/odhcpd-update'wireless:
config wifi-device 'radio0'
option type 'mac80211'
option hwmode '11g'
option path 'platform/ar934x_wmac'
option country 'PL'
option htmode 'HT40'
option txpower '20'
option channel '13'
config wifi-device 'radio1'
option type 'mac80211'
option channel '36'
option hwmode '11a'
option path 'pci0000:00/0000:00:00.0'
option country 'PL'
option htmode 'HT40'
option disabled '0'
config wifi-iface
option ssid 'xxxxx 5G'
option encryption 'psk2'
option device 'radio1'
option mode 'sta'
option bssid '1C:3B:F3:4F:F6:C2'
option key 'xxxxx'
option network 'wwan lan'
config wifi-iface
option device 'radio0'
option mode 'ap'
option ssid 'xxxxxxx 2G'
option encryption 'psk2'
option key 'xxxxxxxx'
option network 'wwan lan wwan1'15 2020-08-31 20:09:39
Odp: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Próbowałem to skonfigurować w Gargoyle, ale po wyborze mostu bezprzewodowego i podłączeniu się do sieci 5GHz, to znika mi sieć 2,4GHz, tak więc nie mogę wybrać wtedy AP na 2,4GHz.
Próbowałem też wyklikać takie ustawienie na LuCI (17.01), ale bez pozytywnego skutku (według opisu podanego przez @AD2014).
Teoretycznie ruter łączy się z internetem, bo mogłem doinstalować wpad, ale jak włączyłem AP na 2,4GHz, to nie przydzielał mi adresu IP i później się już nie chciał łączyć z siecią 5GHz.
Skończyły mi się już pomysły jak mam to zrobić.
Ktoś może potwierdzić, że działa mu taka konfiguracja (i podzielić się konfiguracją)?
16 2020-08-28 11:39:39
Temat: Klient 5GHz + roaming wifi 2GHz (35 odpowiedzi, napisanych Oprogramowanie / Software)
Witam.
Posiadam główny ruter ARCHER C7 z Gargoyle 1.12 (doinstalowane normalne wpad) z internetem z WAN i sieciami po 2 oraz 5GHz.
Drugi ruter WDR4300 (też Gargoyle 1.12) w założeniu ma działać jako klient ARCHERA na 5GHz i rozgłaszać sieć taką jak ARCHER w 2GHz w roamingu, tylko ten drugi tuner żeby miał adres z puli głównego rutera i główny ruter przedzielał adresy DHCP.
Założenie jest takie żeby rozszerzyć sieć 2GHz (wifi roaming) przy użyciu nieobciążonego pasma 5Ghz.
I teraz pytanie, czy taka konfiguracja jest w ogóle możliwa do wykonania (jeżeli tak, to czy da się to zrobić przez GUI i jak to ustawić)?
Ewentualnie jak zrobić żeby rozszerzyć sieć 2GHz (bez ciągnięcia przewodów) przy jak najmniejszych spadkach prędkości?
17 2015-11-24 19:19:14
Odp: Gargoyle:1.5.4 przekierowanie portu z WAN (43 odpowiedzi, napisanych Oprogramowanie / Software)
snifer napisał/a:
Nie możesz mieć tej samej puli adresowej na WAN i LAN routera, zmień jedną adresację np na 192.168.2.x
Że sam to przeoczyłem 
(podstawy sieci komputerowych się kłaniają).
Skupiłem się na firewall, a adresowanie miałem źle ustawione.
Dzięki kolego za pomoc 
18 2015-11-20 10:40:49
Odp: Gargoyle:1.5.4 przekierowanie portu z WAN (43 odpowiedzi, napisanych Oprogramowanie / Software)
Cezary napisał/a:
Ale dmz zrób w modemie na port wan routera, a z wanu dopiero przekierowania. Nie bezpośrednio na 1.50, chyba że to jest ip tego gargoyle.
Adres 192.168.1.50 to adres WAN rutera. Dodatkowo ruter LTE ma możliwość przekierowania dodatkowo 10 portów na lokalne adresy IP. W poprzedniej konfiguracji ze starym ruterem mogłem dostać się z zewnątrz do sieci lokalnej tylko po przekierowaniu portów na modemie LTE + odpowiednia konfiguracja w OpenWrt (tylko, że tam ruter OpenWrt działał w trybie relay).
Próbowałem różnych sposobów (z przekierowaniem portów na modemie LTE jak i bez tego) niestety bez większych rezultatów.
Konfiguracja sieci:
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config interface 'lan'
option ifname 'eth0.1'
option type 'bridge'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
option dns '8.8.8.8 8.8.4.4'
config interface 'wan'
option proto 'ndis'
option device '/dev/ttyUSB0'
option ifname 'wwan0'
option apn 'vpn'
option peerdns '0'
option service 'ndis'
option dns '8.8.8.8 8.8.4.4'
option username 'vpn'
option password 'vpn'
option mobile_isp 'custom'
option proto 'static'
option ipaddr '192.168.1.50'
option netmask '255.255.255.0'
option gateway '192.168.1.200'
config switch
option name 'eth0'
option reset '1'
option enable_vlan '1'
config switch_vlan
option device 'eth0'
option vlan '1'
option ports '0t 2 3 4 5'
config switch_vlan
option device 'eth0'
option vlan '2'
option ports '0t 1'19 2015-11-20 09:39:08
Odp: Gargoyle:1.5.4 przekierowanie portu z WAN (43 odpowiedzi, napisanych Oprogramowanie / Software)
Interesują mnie 3 adresy: 192.168.1.2 (tuner na linuxie), 192.168.1.7 (telewizor) oraz 192.168.1.22 (raspberry pi).
W modemie LTE mam ustawioną strefę DMZ na 192.168.1.50 (adres WAN w ruterze), mam jeszcze przekierowania odpowiednich portów do adresów wewnętrznych. Natomiast jak się połączę poprzez Wi-Fi z modemem (ruter ma funkcje rutera Wi-Fi), to również nie mogę się połączyć bezpośrednio do urządzeń w sieci lokalnej.\
Może tutaj jest coś skopane, tylko że przed zmianą rutera taka konfiguracja działała (stary ruter działał w trybie relay)?
20 2015-11-20 08:35:26
Odp: Gargoyle:1.5.4 przekierowanie portu z WAN (43 odpowiedzi, napisanych Oprogramowanie / Software)
jarek7714 napisał/a:
superprzemo napisał/a:Mam zmieniony port GUI w ruterze na 85, więc to nie to.
To
Wiem o tym, dlatego wkleiłem moją konfigurację firewall, która działała na ruter wr741nd v1 z wgranym OpenWrt Backfire.
Niestety po zmianie rutera na WDR-4300 z Gargoyle PL 1.6.2.2 i podobnej konfiguracji firewall, nie mam dostępu z zewnątrz do urządzeń w sieci lokalnej.
Spędziłem już duuuuużo czasu na różnych konfiguracjach z poziomu GUI jak i przez SSH, ale bez żadnych rezultatów. Stąd moja prośba do mądrzejszych ode mnie, aby pomogli mi zdiagnozować co jest nie tak i pomóc w konfiguracji, żebym mógł się dostać z zewnątrz do urządzeń w sieci wewnętrznej.
Używam rutera oparty, OpenWrt i nigdy nie miałem większego problemu z konfiguracją (przekierowaniem portów).
Proszę o pomoc.
21 2015-11-19 19:43:31
Odp: Gargoyle:1.5.4 przekierowanie portu z WAN (43 odpowiedzi, napisanych Oprogramowanie / Software)
jarek7714 napisał/a:
superprzemo napisał/a:Tak,
Tak jak wspomniałem, z zewnątrz mogę dostać się do rutera (do GUI, przez SCP oraz SSH), natomiast nie mogę się dostać do urządzeń w sieci lokalnej.Bo masz już zajęty port 80 na którym logujesz się do routera na WAN, wystarczy użyć innego zewnętrznego portu 90,92…65535, przekierować go na IP urządzenia w sieci lokalnej i port 80 (dostęp będzie bezproblemowy, z tym że otwarty, także warto mieć inne hasło do sprzętu niż domyślne
Mam zmieniony port GUI w ruterze na 85, więc to nie to.
22 2015-11-19 11:11:53
Odp: Gargoyle:1.5.4 przekierowanie portu z WAN (43 odpowiedzi, napisanych Oprogramowanie / Software)
Cezary napisał/a:
Masz wykupioną usługę publicznego ip u operatora?
Tak,
Tak jak wspomniałem, z zewnątrz mogę dostać się do rutera (do GUI, przez SCP oraz SSH), natomiast nie mogę się dostać do urządzeń w sieci lokalnej.
23 2015-11-19 09:56:52
Odp: Gargoyle:1.5.4 przekierowanie portu z WAN (43 odpowiedzi, napisanych Oprogramowanie / Software)
Witam,
Podepnę się pod temat, ponieważ mam problemy z przekierowaniem portów. Od niedawna mam ruter WDR-4300 połączony z modemem LTE e5372s-32 Huawei podpięty do portu USB. Mogę się z zewnątrz zalogować do serwera Gargoyle PL 1.6.2.2 (b70bfc1) (zmieniłem port na 85) oraz oscam zainstalowany w ruterze. Problem mam z logowaniem z zewnątrz sieci do innych urządzeń podpiętych do sieci lokalnej (w sieci lokalnej mogę się połączyć do każdego urządzenia).
Wcześniej miałem ruter wr741nd v1 z wgranym OpenWrt Backfire 10.03.1 r32191 i na podobnej konfiguracji firewall'a nie miałem problemów z przekierowaniem portów.
Poniżej obecna konfiguracja firewall:
config defaults
option syn_flood '1'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'REJECT'
config zone
option name 'lan'
list network 'lan'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'ACCEPT'
config zone
option name 'wan'
list network 'wan'
list network 'wan6'
option input 'ACCEPT'
option output 'ACCEPT'
option forward 'ACCEPT'
option masq '1'
option mtu_fix '1'
config forwarding
option src 'lan'
option dest 'wan'
config forwarding
option src 'wan'
option dest 'lan'
config rule
option name 'Allow-DHCP-Renew'
option src 'wan'
option proto 'udp'
option dest_port '68'
option target 'ACCEPT'
option family 'ipv4'
config rule
option name 'Allow-Ping'
option src 'wan'
option proto 'icmp'
option icmp_type 'echo-request'
option family 'ipv4'
option target 'ACCEPT'
config rule
option name 'Allow-DHCPv6'
option src 'wan'
option proto 'udp'
option src_ip 'fe80::/10'
option src_port '547'
option dest_ip 'fe80::/10'
option dest_port '546'
option family 'ipv6'
option target 'ACCEPT'
config rule
option name 'Allow-ICMPv6-Input'
option src 'wan'
option proto 'icmp'
list icmp_type 'echo-request'
list icmp_type 'echo-reply'
list icmp_type 'destination-unreachable'
list icmp_type 'packet-too-big'
list icmp_type 'time-exceeded'
list icmp_type 'bad-header'
list icmp_type 'unknown-header-type'
list icmp_type 'router-solicitation'
list icmp_type 'neighbour-solicitation'
list icmp_type 'router-advertisement'
list icmp_type 'neighbour-advertisement'
option limit '1000/sec'
option family 'ipv6'
option target 'ACCEPT'
config rule
option name 'Allow-ICMPv6-Forward'
option src 'wan'
option dest '*'
option proto 'icmp'
list icmp_type 'echo-request'
list icmp_type 'echo-reply'
list icmp_type 'destination-unreachable'
list icmp_type 'packet-too-big'
list icmp_type 'time-exceeded'
list icmp_type 'bad-header'
list icmp_type 'unknown-header-type'
option limit '1000/sec'
option family 'ipv6'
option target 'ACCEPT'
config include
option path '/etc/firewall.user'
option reload '1'
config include
option type 'script'
option path '/usr/lib/gargoyle_firewall_util/gargoyle_additions.firewall'
option family 'IPv4'
option reload '1'
config include 'miniupnpd'
option type 'script'
option path '/usr/share/miniupnpd/firewall.include'
option family 'IPv4'
option reload '1'
config include 'openvpn_include_file'
option path '/etc/openvpn.firewall'
option reload '1'
config rule
option name 'openwebif_uhd'
option src 'wan'
option target 'ACCEPT'
option proto 'tcpudp'
option dest_port '80'
config redirect
option name 'openwebif-uhd'
option src 'wan'
option proto 'tcpudp'
option src_dport '80'
option dest_ip '192.168.1.2'Odpowiedź po iptables -v -L -t nat
Chain PREROUTING (policy ACCEPT 306 packets, 134K bytes)
pkts bytes target prot opt in out source destination
309 134K delegate_prerouting all -- any any anywhere an ywhere
Chain INPUT (policy ACCEPT 19 packets, 1320 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 84 packets, 5585 bytes)
pkts bytes target prot opt in out source destination
Chain POSTROUTING (policy ACCEPT 35 packets, 2357 bytes)
pkts bytes target prot opt in out source destination
105 7247 delegate_postrouting all -- any any anywhere a nywhere
Chain MINIUPNPD (1 references)
pkts bytes target prot opt in out source destination
Chain delegate_postrouting (1 references)
pkts bytes target prot opt in out source destination
105 7247 postrouting_rule all -- any any anywhere anywh ere /* user chain for postrouting */
0 0 zone_lan_postrouting all -- any br-lan anywhere a nywhere
70 4890 zone_wan_postrouting all -- any wwan0 anywhere a nywhere
Chain delegate_prerouting (1 references)
pkts bytes target prot opt in out source destination
309 134K prerouting_rule all -- any any anywhere anywhe re /* user chain for prerouting */
26 1652 zone_lan_prerouting all -- br-lan any anywhere an ywhere
283 132K zone_wan_prerouting all -- wwan0 any anywhere an ywhere
Chain pf_loopback_A (1 references)
pkts bytes target prot opt in out source destination
Chain pf_loopback_C (1 references)
pkts bytes target prot opt in out source destination
Chain postrouting_lan_rule (1 references)
pkts bytes target prot opt in out source destination
Chain postrouting_rule (1 references)
pkts bytes target prot opt in out source destination
0 0 pf_loopback_C all -- any br-lan anywhere anywhere
Chain postrouting_wan_rule (1 references)
pkts bytes target prot opt in out source destination
Chain prerouting_lan_rule (1 references)
pkts bytes target prot opt in out source destination
Chain prerouting_rule (1 references)
pkts bytes target prot opt in out source destination
Chain prerouting_wan_rule (1 references)
pkts bytes target prot opt in out source destination
Chain zone_lan_postrouting (1 references)
pkts bytes target prot opt in out source destination
0 0 postrouting_lan_rule all -- any any anywhere a nywhere /* user chain for postrouting */
0 0 SNAT tcp -- any any 192.168.1.0/24 192.168.1.2 tcp dpt:www /* openwebif-uhd (reflection) */ to:192.168.1.1
0 0 SNAT udp -- any any 192.168.1.0/24 192.168.1.2 udp dpt:80 /* openwebif-uhd (reflection) */ to:192.168.1.1
Chain zone_lan_prerouting (1 references)
pkts bytes target prot opt in out source destination
0 0 pf_loopback_A all -- any any anywhere 192.168. 1.50
26 1652 prerouting_lan_rule all -- any any anywhere an ywhere /* user chain for prerouting */
0 0 DNAT tcp -- any any 192.168.1.0/24 192.168.1.50 tcp dpt:www /* openwebif-uhd (reflection) */ to:192.168.1.2:80
0 0 DNAT udp -- any any 192.168.1.0/24 192.168.1.50 udp dpt:80 /* openwebif-uhd (reflection) */ to:192.168.1.2:80
Chain zone_wan_postrouting (1 references)
pkts bytes target prot opt in out source destination
70 4890 postrouting_wan_rule all -- any any anywhere a nywhere /* user chain for postrouting */
70 4890 MASQUERADE all -- any any anywhere anywhere
Chain zone_wan_prerouting (1 references)
pkts bytes target prot opt in out source destination
283 132K MINIUPNPD all -- any any anywhere anywhere
283 132K prerouting_wan_rule all -- any any anywhere an ywhere /* user chain for prerouting */
0 0 DNAT tcp -- any any anywhere anywhere tcp dpt:www /* openwebif-uhd */ to:192.168.1.2:80
0 0 DNAT udp -- any any anywhere anywhere udp dpt:80 /* openwebif-uhd */ to:192.168.1.2:80Chcę na początku przekierować port 80 na adres 192.168.1.2, proszę o pomoc i podpowiedź co robię źle.
24 2015-10-26 11:56:53
Odp: Modemy USB GSM działające pod Openwrt (79 odpowiedzi, napisanych Oprogramowanie / Software)
modem e5372s-32 Huawei (airbox orange)
vid/pid; 12d1/1506
interfejs połączenia: /dev/ttyUSB0
Gargoyle PL 1.6.2.2
Działa na WDR4300 bez dodatkowego HUB'a.
25 2014-12-04 13:25:38
Odp: Alix garoyle i kompilacja oscama (33 odpowiedzi, napisanych Oprogramowanie / Software)
Trochę to za bardzo skomplikowane jak dla mnie, więc odpuszczam i będę korzystał z obecnie działającego oscam'a.
Znalezione posty: 1 do 25 z 33
eko.one.pl → Posty przez superprzemo
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc