Problem jest tylko taki, że router się nie ładuje z tym skryptem, główna lampka cały czas miga...
Czy jak zrobię i failsafe i mount_root to tak jakbym normalnie uruchomił?
Bo wtedy widać jakiś output.
Strony 1
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Posty przez jacekdob
Strony 1
Problem jest tylko taki, że router się nie ładuje z tym skryptem, główna lampka cały czas miga...
Czy jak zrobię i failsafe i mount_root to tak jakbym normalnie uruchomił?
Bo wtedy widać jakiś output.
No właśnie u mnie dokładnie to samo.
Okazało się, że wcześniej wgrałem /lib/preinit/49_usb_modeswitch, ale nie zainstalowałem usb-modeswitch i usb-modeswitch-data.
Po zainstalowaniu router nie uruchamia się z podłączonym modemem i kartą microSD w nim.
Jak ręcznie uruchomiłem skrypt (trochę komentując) to następuje przełączenie.
Co może być nie tak, że modem nie przełącza się przed zamontowaniem extroota?
Usunąłem vendor=0x12d1 product=0x1506 oraz wgrałem /lib/preinit/49_usb_modeswitch do pamięci w routerze.
Niestety po pierwszym uruchomienu po włączeniu zasilania są błędy extroota.
Po zrebootowaniu nie ma internetu przez modem.
Nie bardzo wiem co dalej...
Jak mam się połączyć przez ncm skoro 62-usb-net-cdc-ncm jest przed 65-usb-serial-option a i tak ładuje się dla modemu option?
Jak zakomentuję option w ogóle, to modem nie w ogóle żadnego sterownika...
A to?
If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=10 Driver=(none)Przy tak załadowanych opcjach WAN się nie łączy.
Jak się nazywa ten tryb do którego go trzeba przełączyć?
Tylko jak usunę "vendor=0x12d1 product=0x1506", to
1) Po ponownym podłączeniu do prądu i tak są błędy extroota:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 80258750, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=3G-6200N console=ttyS1,57600 mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),2752k(rootfs),128k@0x3e0000(cimage)ro,3648k@0x50000(firmware) rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=0004e37a
[ 0.000000] Readback ErrCtl register=0004e37a
[ 0.000000] Memory: 29652k/32768k available (2059k kernel code, 3116k reserved, 343k data, 176k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.010000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
[ 0.090000] pid_max: default: 32768 minimum: 301
[ 0.090000] Mount-cache hash table entries: 512
[ 0.100000] NET: Registered protocol family 16
[ 0.110000] MIPS: machine is Edimax 3g-6200n
[ 0.120000] gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0
[ 0.130000] gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1
[ 0.140000] gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2
[ 0.170000] bio: create slab <bio-0> at 0
[ 0.180000] Switching to clocksource MIPS
[ 0.190000] NET: Registered protocol family 2
[ 0.200000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.220000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.250000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.260000] TCP reno registered
[ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.280000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.290000] NET: Registered protocol family 1
[ 0.340000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.360000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.380000] msgmni has been set to 57
[ 0.390000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.400000] io scheduler noop registered
[ 0.410000] io scheduler deadline registered (default)
[ 0.420000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.440000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
[ 0.450000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.480000] physmap platform flash device: 00800000 at bf000000
[ 0.490000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a8
[ 0.510000] physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
[ 0.510000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.520000] Amd/Fujitsu Extended Query version 1.1.
[ 0.530000] number of CFI chips: 1
[ 0.540000] 7 cmdlinepart partitions found on MTD device physmap-flash.0
[ 0.550000] Creating 7 MTD partitions on "physmap-flash.0":
[ 0.570000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.580000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.600000] 0x000000040000-0x000000050000 : "factory"
[ 0.610000] 0x000000050000-0x000000130000 : "kernel"
[ 0.620000] 0x000000130000-0x0000003e0000 : "rootfs"
[ 0.640000] mtd: partition "rootfs" set to be root filesystem
[ 0.650000] mtd: partition "rootfs_data" created automatically, ofs=360000, len=80000
[ 0.670000] 0x000000360000-0x0000003e0000 : "rootfs_data"
[ 0.680000] 0x0000003e0000-0x000000400000 : "cimage"
[ 0.700000] 0x000000050000-0x0000003e0000 : "firmware"
[ 0.720000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 40, using 40
[ 0.740000] TCP cubic registered
[ 0.750000] NET: Registered protocol family 17
[ 0.760000] Bridge firewalling registered
[ 0.770000] 8021q: 802.1Q VLAN Support v1.8
[ 0.780000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.800000] Freeing unused kernel memory: 176k freed
[ 3.400000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 3.550000] Button Hotplug driver version 0.4.1
[ 3.800000] Registered led device: edimax:green:power
[ 3.800000] Registered led device: edimax:amber:wlan
[ 3.800000] Registered led device: edimax:blue:3g
[ 7.150000] JFFS2 notice: (395) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 8 of xref (0 dead, 3 orphan) found.
[ 8.250000] SCSI subsystem initialized
[ 8.450000] usbcore: registered new interface driver usbfs
[ 8.460000] usbcore: registered new interface driver hub
[ 8.470000] usbcore: registered new device driver usb
[ 8.950000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.990000] dwc_otg: version 2.72a 24-JUN-2008
[ 9.000000] dwc_otg: Core Release: 2.66a
[ 9.210000] dwc_otg: Periodic Transfer Interrupt Enhancement - disabled
[ 9.220000] dwc_otg: Multiprocessor Interrupt Enhancement - disabled
[ 9.240000] dwc_otg: Using DMA mode
[ 9.240000] dwc_otg: Device using Buffer DMA mode
[ 9.250000] dwc_otg dwc_otg.0: DWC OTG Controller
[ 9.260000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[ 9.280000] dwc_otg dwc_otg.0: irq 26, io mem 0x101c0000
[ 9.290000] dwc_otg: Init: Port Power? op_state=1
[ 9.300000] dwc_otg: Init: Power Port (0)
[ 9.310000] hub 1-0:1.0: USB hub found
[ 9.310000] hub 1-0:1.0: 1 port detected
[ 9.350000] Initializing USB Mass Storage driver...
[ 9.360000] usbcore: registered new interface driver usb-storage
[ 9.370000] USB Mass Storage support registered.
[ 9.700000] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 9.910000] scsi0 : usb-storage 1-1:1.0
[ 9.930000] scsi1 : usb-storage 1-1:1.1
[ 10.920000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 10.940000] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 10.960000] sd 1:0:0:0: [sda] 7744512 512-byte logical blocks: (3.96 GB/3.69 GiB)
[ 10.980000] sd 1:0:0:0: [sda] Write Protect is off
[ 10.990000] sd 1:0:0:0: [sda] Mode Sense: 0f 00 00 00
[ 11.000000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.040000] sda: sda1
[ 11.050000] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 30.190000] EXT4-fs (sda1): recovery complete
[ 30.200000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 31.710000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
[ 31.730000] Backport generated by backports.git backports-20140124-0-g1256d3e
[ 32.000000] cfg80211: Calling CRDA to update world regulatory domain
[ 32.020000] cfg80211: World regulatory domain updated:
[ 32.030000] cfg80211: DFS Master region: unset
[ 32.040000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 32.050000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.070000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.090000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 32.100000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 32.120000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 32.130000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 33.280000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT305X.eeprom'.
[ 33.480000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
[ 33.500000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 33.510000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 33.520000] Registered led device: rt2800soc-phy0::radio
[ 33.520000] Registered led device: rt2800soc-phy0::assoc
[ 33.520000] Registered led device: rt2800soc-phy0::quality
[ 34.040000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 34.260000] PPP generic driver version 2.4.2
[ 34.470000] tun: Universal TUN/TAP device driver, 1.6
[ 34.480000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 34.690000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 35.230000] NET: Registered protocol family 24
[ 35.470000] nf_conntrack version 0.5.0 (466 buckets, 1864 max)
[ 36.520000] usbcore: registered new interface driver huawei_ether
[ 36.630000] usbcore: registered new interface driver usbserial
[ 36.650000] USB Serial support registered for generic
[ 36.660000] usbcore: registered new interface driver usbserial_generic
[ 36.670000] usbserial: USB Serial Driver core
[ 36.750000] usbcore: registered new interface driver cdc_wdm
[ 36.800000] usbcore: registered new interface driver cdc_ether
[ 36.910000] usbcore: registered new interface driver cdc_ncm
[ 36.950000] usbcore: registered new interface driver qmi_wwan
[ 37.010000] USB Serial support registered for GSM modem (1-port)
[ 37.020000] usbcore: registered new interface driver option
[ 37.030000] option: v0.7.2:USB Driver for GSM modems
[ 45.060000] device eth0.1 entered promiscuous mode
[ 45.070000] device eth0 entered promiscuous mode
[ 45.080000] br-lan: port 1(eth0.1) entered forwarding state
[ 45.090000] br-lan: port 1(eth0.1) entered forwarding state
[ 47.090000] br-lan: port 1(eth0.1) entered forwarding state
[ 48.390000] cfg80211: Calling CRDA for country: PL
[ 48.400000] cfg80211: Regulatory domain changed to country: PL
[ 48.410000] cfg80211: DFS Master region: ETSI
[ 48.420000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 48.430000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 48.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 48.460000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 48.480000] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[ 48.490000] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 51.260000] device wlan0 entered promiscuous mode
[ 61.660000] br-lan: port 2(wlan0) entered forwarding state
[ 61.670000] br-lan: port 2(wlan0) entered forwarding state
[ 63.670000] br-lan: port 2(wlan0) entered forwarding state
[ 73.480000] ramips-wdt: timeout value 60 must be 0 < timeout <= 40, using 40
[ 77.790000] hub 1-0:1.0: port 1 disabled by hub (EMI?), re-enabling...
[ 77.800000] usb 1-1: USB disconnect, device number 2
[ 77.820000] sd 1:0:0:0: [sda] Synchronizing SCSI cache
[ 77.830000] sd 1:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
[ 78.180000] usb 1-1: new high-speed USB device number 3 using dwc_otg
[ 78.400000] option 1-1:1.1: GSM modem (1-port) converter detected
[ 78.410000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 78.430000] scsi2 : usb-storage 1-1:1.3
[ 78.440000] scsi3 : usb-storage 1-1:1.4
[ 79.440000] scsi 2:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 79.460000] scsi 3:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 79.480000] sd 3:0:0:0: [sdb] 7744512 512-byte logical blocks: (3.96 GB/3.69 GiB)
[ 79.510000] sd 3:0:0:0: [sdb] Write Protect is off
[ 79.520000] sd 3:0:0:0: [sdb] Mode Sense: 0f 00 00 00
[ 79.520000] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 79.560000] sdb: sdb1
[ 79.570000] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 110.920000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #448: comm hotplug-call: reading directory lblock 0
[ 112.860000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #448: comm hotplug-call: reading directory lblock 0
[ 114.170000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm dropbear: reading directory lblock 0
[ 114.260000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm ash: reading directory lblock 0
[ 114.290000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm ash: reading directory lblock 0
[ 114.340000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #960: comm ash: reading directory lblock 0
[ 114.400000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm ash: reading directory lblock 0
[ 114.430000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm ash: reading directory lblock 0
[ 114.480000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #960: comm ash: reading directory lblock 0
[ 114.510000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm ash: reading directory lblock 0
[ 114.540000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm ash: reading directory lblock 0
[ 114.580000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm ash: reading directory lblock 0
[ 114.620000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm ash: reading directory lblock 0
[ 114.650000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm ash: reading directory lblock 0
[ 114.680000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm ash: reading directory lblock 0
[ 115.000000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #960: comm sysinfo.sh: reading directory lblock 0
[ 115.030000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm sysinfo.sh: reading directory lblock 0
[ 115.070000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm sysinfo.sh: reading directory lblock 0
[ 115.230000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #960: comm sysinfo.sh: reading directory lblock 0
[ 115.310000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm df: reading directory lblock 0
[ 115.340000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm df: reading directory lblock 0
[ 115.370000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm df: reading directory lblock 0
[ 115.400000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm df: reading directory lblock 0
[ 115.440000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm df: reading directory lblock 0
[ 115.860000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm uci: reading directory lblock 0
[ 115.890000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm uci: reading directory lblock 0
[ 115.910000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm uci: reading directory lblock 0
[ 115.940000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm uci: reading directory lblock 0
[ 116.020000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #960: comm sysinfo.sh: reading directory lblock 0
[ 116.060000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm sysinfo.sh: reading directory lblock 0
[ 116.590000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #960: comm sysinfo.sh: reading directory lblock 0
[ 116.620000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm sysinfo.sh: reading directory lblock 0
[ 116.750000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #829: comm ash: reading directory lblock 0
[ 121.310000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #448: comm hotplug-call: reading directory lblock 0
[ 121.690000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #448: comm hotplug-call: reading directory lblock 0
[ 122.700000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #960: comm hotplug-call: reading directory lblock 0
[ 125.160000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #960: comm hotplug-call: reading directory lblock 0
[ 125.180000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #2: comm mkdir: reading directory lblock 0
[ 125.200000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm hotplug-call: reading directory lblock 0
[ 125.230000] EXT4-fs error (device sda1): ext4_read_inode_bitmap:161: comm mkdir: Cannot read inode bitmap - block_group = 0, inode_bitmap = 254
[ 125.250000] EXT4-fs error (device sda1) in ext4_new_inode:941: IO failure
[ 125.270000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm hotplug-call: reading directory lblock 0
[ 128.590000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #47: comm uhttpd: reading directory lblock 0
[ 131.060000] Buffer I/O error on device sda1, logical block 425984
[ 131.060000] lost page write due to I/O error on sda1
[ 131.080000] JBD2: I/O error detected when updating journal superblock for sda1-8.
[ 131.090000] Aborting journal on device sda1-8.
[ 131.100000] Buffer I/O error on device sda1, logical block 425984
[ 131.100000] lost page write due to I/O error on sda1
[ 131.130000] JBD2: I/O error detected when updating journal superblock for sda1-8.
[ 131.490000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #960: comm ash: reading directory lblock 0Dopiero reboot przy włączonym prądzie pomaga:
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Sat Mar 15 11:29:43 CET 2014
[ 0.000000] prom: fw_arg0=00000001, fw_arg1=01f57fb0, fw_arg2=01f583b0, fw_arg3=00000000
[ 0.000000] env[0]: memsize=32
[ 0.000000] env[1]: initrd_start=0x00000000
[ 0.000000] env[2]: initrd_size=0x0
[ 0.000000] env[3]: flash_start=0xBFC00000
[ 0.000000] env[4]: flash_size=0x400000
[ 0.000000] env[0]: memsize=32
[ 0.000000] env[1]: initrd_start=0x00000000
[ 0.000000] env[2]: initrd_size=0x0
[ 0.000000] env[3]: flash_start=0xBFC00000
[ 0.000000] env[4]: flash_size=0x400000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] Ralink RT3052 id:1 rev:2 running at 320.00 MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 80258750, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=3G-6200N console=ttyS1,57600 mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),2752k(rootfs),128k@0x3e0000(cimage)ro,3648k@0x50000(firmware) rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=0004e370
[ 0.000000] Readback ErrCtl register=0004e370
[ 0.000000] Memory: 29652k/32768k available (2059k kernel code, 3116k reserved, 343k data, 176k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.010000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
[ 0.090000] pid_max: default: 32768 minimum: 301
[ 0.090000] Mount-cache hash table entries: 512
[ 0.100000] NET: Registered protocol family 16
[ 0.110000] MIPS: machine is Edimax 3g-6200n
[ 0.120000] gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0
[ 0.130000] gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1
[ 0.140000] gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2
[ 0.170000] bio: create slab <bio-0> at 0
[ 0.180000] Switching to clocksource MIPS
[ 0.190000] NET: Registered protocol family 2
[ 0.200000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.220000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.250000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.260000] TCP reno registered
[ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.280000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.290000] NET: Registered protocol family 1
[ 0.340000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.360000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.380000] msgmni has been set to 57
[ 0.390000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.400000] io scheduler noop registered
[ 0.410000] io scheduler deadline registered (default)
[ 0.420000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.440000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
[ 0.450000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.480000] physmap platform flash device: 00800000 at bf000000
[ 0.490000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a8
[ 0.510000] physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
[ 0.510000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.520000] Amd/Fujitsu Extended Query version 1.1.
[ 0.530000] number of CFI chips: 1
[ 0.540000] 7 cmdlinepart partitions found on MTD device physmap-flash.0
[ 0.550000] Creating 7 MTD partitions on "physmap-flash.0":
[ 0.570000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.580000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.600000] 0x000000040000-0x000000050000 : "factory"
[ 0.610000] 0x000000050000-0x000000130000 : "kernel"
[ 0.620000] 0x000000130000-0x0000003e0000 : "rootfs"
[ 0.640000] mtd: partition "rootfs" set to be root filesystem
[ 0.650000] mtd: partition "rootfs_data" created automatically, ofs=360000, len=80000
[ 0.670000] 0x000000360000-0x0000003e0000 : "rootfs_data"
[ 0.680000] 0x0000003e0000-0x000000400000 : "cimage"
[ 0.700000] 0x000000050000-0x0000003e0000 : "firmware"
[ 0.720000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 40, using 40
[ 0.740000] TCP cubic registered
[ 0.750000] NET: Registered protocol family 17
[ 0.760000] Bridge firewalling registered
[ 0.770000] 8021q: 802.1Q VLAN Support v1.8
[ 0.780000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.800000] Freeing unused kernel memory: 176k freed
[ 3.400000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 3.550000] Button Hotplug driver version 0.4.1
[ 3.800000] Registered led device: edimax:green:power
[ 3.800000] Registered led device: edimax:amber:wlan
[ 3.800000] Registered led device: edimax:blue:3g
[ 7.150000] JFFS2 notice: (395) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 8 of xref (0 dead, 3 orphan) found.
[ 8.250000] SCSI subsystem initialized
[ 8.450000] usbcore: registered new interface driver usbfs
[ 8.460000] usbcore: registered new interface driver hub
[ 8.480000] usbcore: registered new device driver usb
[ 8.950000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.990000] dwc_otg: version 2.72a 24-JUN-2008
[ 9.000000] dwc_otg: Core Release: 2.66a
[ 9.210000] dwc_otg: Periodic Transfer Interrupt Enhancement - disabled
[ 9.220000] dwc_otg: Multiprocessor Interrupt Enhancement - disabled
[ 9.240000] dwc_otg: Using DMA mode
[ 9.240000] dwc_otg: Device using Buffer DMA mode
[ 9.250000] dwc_otg dwc_otg.0: DWC OTG Controller
[ 9.260000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[ 9.280000] dwc_otg dwc_otg.0: irq 26, io mem 0x101c0000
[ 9.290000] dwc_otg: Init: Port Power? op_state=1
[ 9.300000] dwc_otg: Init: Power Port (0)
[ 9.310000] hub 1-0:1.0: USB hub found
[ 9.320000] hub 1-0:1.0: 1 port detected
[ 9.350000] Initializing USB Mass Storage driver...
[ 9.360000] usbcore: registered new interface driver usb-storage
[ 9.370000] USB Mass Storage support registered.
[ 9.700000] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 9.920000] scsi0 : usb-storage 1-1:1.3
[ 9.930000] scsi1 : usb-storage 1-1:1.4
[ 10.920000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 10.940000] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 10.960000] sd 1:0:0:0: [sda] 7744512 512-byte logical blocks: (3.96 GB/3.69 GiB)
[ 10.990000] sd 1:0:0:0: [sda] Write Protect is off
[ 11.000000] sd 1:0:0:0: [sda] Mode Sense: 0f 00 00 00
[ 11.000000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.040000] sda: sda1
[ 11.050000] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 30.150000] EXT4-fs (sda1): recovery complete
[ 30.160000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 31.710000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
[ 31.730000] Backport generated by backports.git backports-20140124-0-g1256d3e
[ 32.010000] cfg80211: Calling CRDA to update world regulatory domain
[ 32.020000] cfg80211: World regulatory domain updated:
[ 32.030000] cfg80211: DFS Master region: unset
[ 32.040000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 32.060000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.070000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.090000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 32.100000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 32.120000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 32.130000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 33.280000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT305X.eeprom'.
[ 33.480000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected
[ 33.500000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 33.510000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 33.510000] Registered led device: rt2800soc-phy0::radio
[ 33.510000] Registered led device: rt2800soc-phy0::assoc
[ 33.510000] Registered led device: rt2800soc-phy0::quality
[ 34.040000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 34.250000] PPP generic driver version 2.4.2
[ 34.460000] tun: Universal TUN/TAP device driver, 1.6
[ 34.470000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 34.680000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 35.230000] NET: Registered protocol family 24
[ 35.470000] nf_conntrack version 0.5.0 (466 buckets, 1864 max)
[ 36.520000] usbcore: registered new interface driver huawei_ether
[ 36.640000] usbcore: registered new interface driver usbserial
[ 36.650000] USB Serial support registered for generic
[ 36.660000] usbcore: registered new interface driver usbserial_generic
[ 36.680000] usbserial: USB Serial Driver core
[ 36.760000] usbcore: registered new interface driver cdc_wdm
[ 36.810000] usbcore: registered new interface driver cdc_ether
[ 36.910000] usbcore: registered new interface driver cdc_ncm
[ 36.960000] usbcore: registered new interface driver qmi_wwan
[ 37.010000] USB Serial support registered for GSM modem (1-port)
[ 37.030000] option 1-1:1.1: GSM modem (1-port) converter detected
[ 37.040000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[ 37.050000] usbcore: registered new interface driver option
[ 37.070000] option: v0.7.2:USB Driver for GSM modems
[ 45.640000] device eth0.1 entered promiscuous mode
[ 45.650000] device eth0 entered promiscuous mode
[ 45.670000] br-lan: port 1(eth0.1) entered forwarding state
[ 45.680000] br-lan: port 1(eth0.1) entered forwarding state
[ 47.680000] br-lan: port 1(eth0.1) entered forwarding state
[ 49.320000] cfg80211: Calling CRDA for country: PL
[ 49.330000] cfg80211: Regulatory domain changed to country: PL
[ 49.340000] cfg80211: DFS Master region: ETSI
[ 49.350000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 49.360000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 49.380000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 49.390000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 49.410000] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm)
[ 49.420000] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 53.210000] device wlan0 entered promiscuous mode
[ 59.930000] ramips-wdt: timeout value 60 must be 0 < timeout <= 40, using 40
[ 63.610000] br-lan: port 2(wlan0) entered forwarding state
[ 63.620000] br-lan: port 2(wlan0) entered forwarding state
[ 65.620000] br-lan: port 2(wlan0) entered forwarding state2) Ale i tak modem nie jest w pełni rozpoznany i nie ma internetu:
root@OpenWrt:~# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8 dwc_otg
S: Product=DWC OTG Controller
S: SerialNumber=dwc_otg.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1506 Rev= 1.02
S: Manufacturer=HUAWEI Technology
S: Product=HUAWEI Mobile
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=10 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I: If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=huawei_ether
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I:* If#= 2 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=huawei_ether
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0msprzy konfiguracji wanu:
root@OpenWrt:~# uci show network
network.loopback=interface
network.loopback.ifname=lo
network.loopback.proto=static
network.loopback.ipaddr=127.0.0.1
network.loopback.netmask=255.0.0.0
network.lan=interface
network.lan.ifname=eth0.1
network.lan.type=bridge
network.lan.proto=static
network.lan.netmask=255.255.255.0
network.lan.macaddr=00:11:22:33:44:55
network.lan.ipaddr=192.168.2.1
network.@switch[0]=switch
network.@switch[0].name=rt305x
network.@switch[0].reset=1
network.@switch[0].enable_vlan=1
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device=rt305x
network.@switch_vlan[0].vlan=1
network.@switch_vlan[0].ports=0 1 2 3 5 6t
network.@switch_vlan[1]=switch_vlan
network.@switch_vlan[1].device=rt305x
network.@switch_vlan[1].vlan=2
network.@switch_vlan[1].ports=4 6t
network.wan=interface
network.wan._orig_ifname=wwan0
network.wan._orig_bridge=false
network.wan.proto=3g
network.wan.service=umts
network.wan.apn=eranet
network.wan.device=/dev/ttyUSB0Moduł option jest do obsługi modemów Huawei, pytanie było po co wymusiłeś usbserial generyczny na nim?
A jak go odmusić?
To co mam zmienić?
Modem jest wykrywany i łączy z internetem przy takiej konfiguracji:
root@OpenWrt:/etc/modules.d# for f in *; do echo "###Filename: $f###"; cat "$f"; done
###Filename: 01-crypto-core###
crypto_algapi
###Filename: 09-crypto-aes###
aes_generic
###Filename: 09-crypto-arc4###
arc4
###Filename: 19-input-core###
input-core
###Filename: 20-cfg80211###
compat
cfg80211
###Filename: 20-eeprom-93cx6###
eeprom_93cx6
###Filename: 20-input-polldev###
input-polldev
###Filename: 20-lib-crc-ccitt###
crc-ccitt
###Filename: 20-lib-crc-itu-t###
crc-itu-t
###Filename: 20-lib-crc16###
crc16
###Filename: 20-nls-base###
nls_base
###Filename: 20-scsi-core###
scsi_mod
###Filename: 20-usb-core###
usb-common
usbcore
###Filename: 21-mac80211###
mac80211
###Filename: 24-rt2x00-lib###
rt2x00lib
###Filename: 25-nls-cp437###
nls_cp437
###Filename: 25-nls-iso8859-1###
nls_iso8859-1
###Filename: 25-rt2x00-mmio###
rt2x00mmio
###Filename: 27-rt2800-lib###
rt2800lib
###Filename: 28-rt2800-mmio###
rt2800mmio
###Filename: 29-rt2800-soc###
rt2x00soc
rt2800soc
###Filename: 30-button-hotplug###
button-hotplug
###Filename: 30-fs-ext4###
mbcache
jbd2
ext4
###Filename: 30-fs-vfat###
fat
vfat
###Filename: 30-gpio-button-hotplug###
gpio-button-hotplug
###Filename: 30-ppp###
slhc
ppp_generic
ppp_async
###Filename: 30-tun###
tun
###Filename: 40-ipt-core###
x_tables
xt_tcpudp
ip_tables
iptable_filter
iptable_mangle
xt_limit
xt_mac
xt_multiport
xt_comment
ipt_LOG
xt_TCPMSS
ipt_REJECT
###Filename: 40-pppox###
pppox
###Filename: 40-scsi-core###
sd_mod
###Filename: 40-usb2###
ehci-hcd
###Filename: 41-ipt-conntrack###
nf_conntrack
nf_defrag_ipv4
nf_conntrack_ipv4
xt_state
iptable_raw
xt_NOTRACK
xt_CT
xt_conntrack
###Filename: 41-pppoe###
pppoe
###Filename: 42-ipt-nat###
nf_nat
iptable_nat
ipt_MASQUERADE
###Filename: 45-ipt-nathelper###
nf_conntrack_ftp
nf_nat_ftp
nf_conntrack_irc
nf_nat_irc
###Filename: 50-ledtrig-usbdev###
ledtrig-usbdev
###Filename: 54-usb-rt305x-dwc_otg###
dwc_otg
###Filename: 60-huawei-hw-cdc###
hw_cdc_driver
###Filename: 60-leds-gpio###
leds-gpio
###Filename: 60-usb-net###
usbnet
###Filename: 60-usb-serial###
usbserial vendor=0x12d1 product=0x1506
###Filename: 60-usb-storage###
usb-storage
###Filename: 60-usb-wdm###
cdc-wdm
###Filename: 61-usb-net-cdc-ether###
cdc_ether
###Filename: 61-usb-serial-wwan###
usb_wwan
###Filename: 62-input-gpio-keys-polled###
gpio_keys_polled
###Filename: 62-usb-net-cdc-ncm###
cdc_ncm
###Filename: 62-usb-net-qmi-wwan###
qmi_wwan
###Filename: 65-usb-serial-option###
optionJak zakomentuję "usbserial vendor=0x12d1 product=0x1506" to modem nie ma przypisanego sterownika i nie łączy z internetem.
Gdy extroot jest poprawnie zamontowany to tworzenie pliku nie ma sensu bo i tak będzie tylko na karcie SD a nie na routerze.
Jak extroot nie jest poprawnie zamontowany, to nie można nic zapisać, bo wszystko jest read-only.
Jak zatem zapisać plik, który by resetował router?
Czego mam szukać dla modemu by się nie przełączał?
Na razie mam:
root@OpenWrt:~# cat /etc/modules.d/60-usb-serial
usbserial vendor=0x12d1 product=0x1506root@OpenWrt:/proc/1# cat /sys/kernel/debug/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8 dwc_otg
S: Product=DWC OTG Controller
S: SerialNumber=dwc_otg.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=12d1 ProdID=1506 Rev= 1.02
S: Manufacturer=HUAWEI Technology
S: Product=HUAWEI Mobile
C:* #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=10 Driver=usbserial_generic
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=02 Prot=12 Driver=usbserial_generic
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I: If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=16 Driver=huawei_ether
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I:* If#= 2 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=16 Driver=huawei_ether
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0msroot@OpenWrt:/proc/1# gcom -d /dev/ttyUSB1 info
##### Wireless WAN Modem Configuration #####
Product text:
====
Manufacturer: huawei
Model: E3276
Revision: 21.430.03.04.55
IMEI: xxxxxxxxxxxxxxx
+GCAP: +CGSM,+DS,+ES
OK
====
Manufacturer: huawei
IMEI and Serial Number: xxxxxxxxxxxxxxx
Manufacturer's Revision:
21.430.03.04.
Hardware Revision:
Network Locked: ERROR:
Customisation:
Band settings: (
)
APN: 0,"IP","","",0,0,0,0
##### END #####Pozdrawiam,
Jacek D.
Witam,
Posiadam Edimax 3G-6200n.
Mam zrobiony extroot, który jest na karcie microSD w modemie Huawei e3276.
Po włączeniu zasilania w routerze extroot nie jest dobrze montowany, są błędy.
[ 78.520000] scsi2 : usb-storage 1-1:1.3
[ 78.530000] scsi3 : usb-storage 1-1:1.4
[ 79.520000] scsi 2:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 79.540000] scsi 3:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 79.570000] sd 3:0:0:0: [sdb] 7744512 512-byte logical blocks: (3.96 GB/3.69 GiB)
[ 79.590000] sd 3:0:0:0: [sdb] Write Protect is off
[ 79.600000] sd 3:0:0:0: [sdb] Mode Sense: 0f 00 00 00
[ 79.600000] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 79.640000] sdb: sdb1
[ 79.660000] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[ 93.350000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm dropbear: reading directory lblock 0
[ 93.410000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #2: comm dropbear: reading directory lblock 0
[ 93.440000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm ash: reading directory lblock 0
[ 93.470000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm ash: reading directory lblock 0
[ 93.510000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm ash: reading directory lblock 0
[ 93.540000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm ash: reading directory lblock 0
[ 93.580000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm ash: reading directory lblock 0
[ 93.600000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm ash: reading directory lblock 0
[ 93.620000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm ash: reading directory lblock 0
[ 93.640000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm ash: reading directory lblock 0
[ 93.660000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #12: comm ash: reading directory lblock 0
[ 93.690000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm ash: reading directory lblock 0
[ 93.910000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm sysinfo.sh: reading directory lblock 0
[ 93.940000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm sysinfo.sh: reading directory lblock 0
[ 94.300000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm sysinfo.sh: reading directory lblock 0
[ 94.650000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm sysinfo.sh: reading directory lblock 0
[ 94.670000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #232: comm sysinfo.sh: reading directory lblock 0
[ 94.710000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #128: comm sysinfo.sh: reading directory lblock 0
[ 111.300000] EXT4-fs error (device sda1): ext4_find_entry:935: inode #448: comm hotplug-call: reading directory lblock 0Dopiero po zrobieniu reboota jest dobrze:
[ 9.910000] scsi0 : usb-storage 1-1:1.3
[ 9.920000] scsi1 : usb-storage 1-1:1.4
[ 10.920000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 10.940000] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 10.960000] sd 1:0:0:0: [sda] 7744512 512-byte logical blocks: (3.96 GB/3.69 GiB)
[ 10.990000] sd 1:0:0:0: [sda] Write Protect is off
[ 11.000000] sd 1:0:0:0: [sda] Mode Sense: 0f 00 00 00
[ 11.000000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.040000] sda: sda1
[ 11.050000] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 30.150000] EXT4-fs (sda1): recovery complete
[ 30.160000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)I tak zawsze trzeba zrobić, po wznowieniu zasilania.
Co mogę zrobić by działało to od razu?
(Względnie może być skrypt który go zrestartuje...)
Pozdrawiam
Jacek D.
Miałem na myśli do binarki...
Dziękuję.
Po zainstalowaniu ruszyło od razu.
Pozdrawiam.
PS.
Może warto dorzucić do builda?
Robiłem,
niestety nic:
root@OpenWrt:~# wifi detect
root@OpenWrt:~#Witam,
po zainstalowaniu:
http://ecco.selfip.net/attitude_adjustm … pgrade.bin
2014-Mar-15 11:31:27 3.1M
Nie ma w ogóle interfejsu radiowego Wifi.
Dioda Wifi się nie pali.
W Luci nie ma zakładki Wifi.
Przy oryginalnym sofcie producenta oczywiście wifi działa.
Z góry dziękuję za pomoc.
root@OpenWrt:~# ifconfig -a
3g-wan Link encap:Point-to-Point Protocol
inet addr:213.158.209.24 P-t-P:10.64.64.64 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:34855 errors:8 dropped:0 overruns:0 frame:0
TX packets:27159 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:33485122 (31.9 MiB) TX bytes:11948016 (11.3 MiB)
br-lan Link encap:Ethernet HWaddr 00:11:22:33:44:55
inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:30217 errors:0 dropped:258 overruns:0 frame:0
TX packets:36451 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:12527674 (11.9 MiB) TX bytes:34776214 (33.1 MiB)
eth0 Link encap:Ethernet HWaddr 00:11:22:33:44:55
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:30330 errors:0 dropped:20 overruns:0 frame:0
TX packets:36452 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:13101960 (12.4 MiB) TX bytes:34961776 (33.3 MiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr 00:11:22:33:44:55
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:30221 errors:0 dropped:3 overruns:0 frame:0
TX packets:36451 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:12527858 (11.9 MiB) TX bytes:34776214 (33.1 MiB)
eth1 Link encap:Ethernet HWaddr 00:01:02:03:04:05
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:385 errors:0 dropped:0 overruns:0 frame:0
TX packets:385 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:31775 (31.0 KiB) TX bytes:31775 (31.0 KiB)root@OpenWrt:~# uci show wireless
uci: Entry not foundroot@OpenWrt:~# uci show
dhcp.@dnsmasq[0]=dnsmasq
dhcp.@dnsmasq[0].domainneeded=1
dhcp.@dnsmasq[0].boguspriv=1
dhcp.@dnsmasq[0].localise_queries=1
dhcp.@dnsmasq[0].rebind_protection=1
dhcp.@dnsmasq[0].rebind_localhost=1
dhcp.@dnsmasq[0].local=/lan/
dhcp.@dnsmasq[0].domain=lan
dhcp.@dnsmasq[0].expandhosts=1
dhcp.@dnsmasq[0].authoritative=1
dhcp.@dnsmasq[0].readethers=1
dhcp.@dnsmasq[0].leasefile=/tmp/dhcp.leases
dhcp.@dnsmasq[0].resolvfile=/tmp/resolv.conf.auto
dhcp.lan=dhcp
dhcp.lan.interface=lan
dhcp.lan.start=100
dhcp.lan.limit=150
dhcp.lan.leasetime=12h
dhcp.wan=dhcp
dhcp.wan.interface=wan
dhcp.wan.ignore=1
dropbear.@dropbear[0]=dropbear
dropbear.@dropbear[0].PasswordAuth=on
dropbear.@dropbear[0].Port=22
firewall.@defaults[0]=defaults
firewall.@defaults[0].syn_flood=1
firewall.@defaults[0].input=ACCEPT
firewall.@defaults[0].output=ACCEPT
firewall.@defaults[0].forward=REJECT
firewall.@zone[0]=zone
firewall.@zone[0].name=lan
firewall.@zone[0].input=ACCEPT
firewall.@zone[0].output=ACCEPT
firewall.@zone[0].forward=REJECT
firewall.@zone[0].network=lan
firewall.@zone[1]=zone
firewall.@zone[1].name=wan
firewall.@zone[1].input=REJECT
firewall.@zone[1].output=ACCEPT
firewall.@zone[1].forward=REJECT
firewall.@zone[1].masq=1
firewall.@zone[1].mtu_fix=1
firewall.@zone[1].network=wan wan6
firewall.@forwarding[0]=forwarding
firewall.@forwarding[0].src=lan
firewall.@forwarding[0].dest=wan
firewall.@rule[0]=rule
firewall.@rule[0].name=Allow-DHCP-Renew
firewall.@rule[0].src=wan
firewall.@rule[0].proto=udp
firewall.@rule[0].dest_port=68
firewall.@rule[0].target=ACCEPT
firewall.@rule[0].family=ipv4
firewall.@rule[1]=rule
firewall.@rule[1].name=Allow-Ping
firewall.@rule[1].src=wan
firewall.@rule[1].proto=icmp
firewall.@rule[1].icmp_type=echo-request
firewall.@rule[1].family=ipv4
firewall.@rule[1].target=ACCEPT
firewall.@rule[2]=rule
firewall.@rule[2].name=Allow-DHCPv6
firewall.@rule[2].src=wan
firewall.@rule[2].proto=udp
firewall.@rule[2].src_ip=fe80::/10
firewall.@rule[2].src_port=547
firewall.@rule[2].dest_ip=fe80::/10
firewall.@rule[2].dest_port=546
firewall.@rule[2].family=ipv6
firewall.@rule[2].target=ACCEPT
firewall.@rule[3]=rule
firewall.@rule[3].name=Allow-ICMPv6-Input
firewall.@rule[3].src=wan
firewall.@rule[3].proto=icmp
firewall.@rule[3].icmp_type=echo-request echo-reply destination-unreachable packet-too-big time-exceeded bad-header unknown-header-type router-solicitation neighbour-solicitation router-advertisement neighbour-advertisement
firewall.@rule[3].limit=1000/sec
firewall.@rule[3].family=ipv6
firewall.@rule[3].target=ACCEPT
firewall.@rule[4]=rule
firewall.@rule[4].name=Allow-ICMPv6-Forward
firewall.@rule[4].src=wan
firewall.@rule[4].dest=*
firewall.@rule[4].proto=icmp
firewall.@rule[4].icmp_type=echo-request echo-reply destination-unreachable packet-too-big time-exceeded bad-header unknown-header-type
firewall.@rule[4].limit=1000/sec
firewall.@rule[4].family=ipv6
firewall.@rule[4].target=ACCEPT
firewall.@include[0]=include
firewall.@include[0].path=/etc/firewall.user
fstab.automount=global
fstab.automount.from_fstab=1
fstab.automount.anon_mount=1
fstab.autoswap=global
fstab.autoswap.from_fstab=1
fstab.autoswap.anon_swap=0
fstab.@mount[0]=mount
fstab.@mount[0].target=/overlay
fstab.@mount[0].device=/dev/sda98
fstab.@mount[0].fstype=ext4
fstab.@mount[0].options=rw,noatime
fstab.@mount[0].enabled_fsck=0
fstab.@mount[0].enabled=0
fstab.@swap[0]=swap
fstab.@swap[0].device=/dev/sda99
fstab.@swap[0].enabled=0
luci.main=core
luci.main.lang=auto
luci.main.mediaurlbase=/luci-static/openwrt.org
luci.main.resourcebase=/luci-static/resources
luci.flash_keep=extern
luci.flash_keep.uci=/etc/config/
luci.flash_keep.dropbear=/etc/dropbear/
luci.flash_keep.openvpn=/etc/openvpn/
luci.flash_keep.passwd=/etc/passwd
luci.flash_keep.opkg=/etc/opkg.conf
luci.flash_keep.firewall=/etc/firewall.user
luci.flash_keep.uploads=/lib/uci/upload/
luci.languages=internal
luci.languages.en=English
luci.sauth=internal
luci.sauth.sessionpath=/tmp/luci-sessions
luci.sauth.sessiontime=3600
luci.ccache=internal
luci.ccache.enable=1
luci.themes=internal
luci.themes.OpenWrt=/luci-static/openwrt.org
network.loopback=interface
network.loopback.ifname=lo
network.loopback.proto=static
network.loopback.ipaddr=127.0.0.1
network.loopback.netmask=255.0.0.0
network.lan=interface
network.lan.ifname=eth0.1
network.lan.type=bridge
network.lan.proto=static
network.lan.netmask=255.255.255.0
network.lan.macaddr=00:11:22:33:44:55
network.lan.ipaddr=192.168.2.1
network.@switch[0]=switch
network.@switch[0].name=rt305x
network.@switch[0].reset=1
network.@switch[0].enable_vlan=1
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device=rt305x
network.@switch_vlan[0].vlan=1
network.@switch_vlan[0].ports=0 1 2 3 5 6t
network.@switch_vlan[1]=switch_vlan
network.@switch_vlan[1].device=rt305x
network.@switch_vlan[1].vlan=2
network.@switch_vlan[1].ports=4 6t
network.wan=interface
network.wan._orig_ifname=wwan0
network.wan._orig_bridge=false
network.wan.proto=3g
network.wan.service=umts
network.wan.apn=eranet
network.wan.device=/dev/ttyUSB0
system.@system[0]=system
system.@system[0].hostname=OpenWrt
system.@system[0].timezone=CET-1CEST,M3.5.0,M10.5.0/3
system.@system[0].zonename=Europe/Warsaw
system.ntp=timeserver
system.ntp.server=0.pool.ntp.org 1.pool.ntp.org 2.pool.ntp.org 3.pool.ntp.org
system.ntp.enable_server=0
system.wifi_button=button
system.wifi_button.button=wps
system.wifi_button.action=released
system.wifi_button.handler=/sbin/wifionoff
system.wifi_button.min=0
system.wifi_button.max=2
system.reboot_button=button
system.reboot_button.button=reset
system.reboot_button.action=released
system.reboot_button.handler=reboot
system.reboot_button.min=3
system.reboot_button.max=10
system.reset_button=button
system.reset_button.button=reset
system.reset_button.action=released
system.reset_button.handler=/sbin/firstboot ; reboot
system.reset_button.min=11
system.reset_button.max=90
system.led_wifi_led=led
system.led_wifi_led.name=wifi
system.led_wifi_led.sysfs=edimax:amber:wlan
system.led_wifi_led.trigger=netdev
system.led_wifi_led.dev=wlan0
system.led_wifi_led.mode=link tx rx
system.led_usb=led
system.led_usb.name=USB
system.led_usb.sysfs=edimax:blue:3g
system.led_usb.trigger=usbdev
system.led_usb.dev=1-1
system.led_usb.interval=50
ucitrack.@network[0]=network
ucitrack.@network[0].init=network
ucitrack.@network[0].affects=dhcp radvd
ucitrack.@wireless[0]=wireless
ucitrack.@wireless[0].affects=network
ucitrack.@firewall[0]=firewall
ucitrack.@firewall[0].init=firewall
ucitrack.@firewall[0].affects=luci-splash qos miniupnpd
ucitrack.@olsr[0]=olsr
ucitrack.@olsr[0].init=olsrd
ucitrack.@dhcp[0]=dhcp
ucitrack.@dhcp[0].init=dnsmasq
ucitrack.@dropbear[0]=dropbear
ucitrack.@dropbear[0].init=dropbear
ucitrack.@httpd[0]=httpd
ucitrack.@httpd[0].init=httpd
ucitrack.@fstab[0]=fstab
ucitrack.@fstab[0].init=fstab
ucitrack.@qos[0]=qos
ucitrack.@qos[0].init=qos
ucitrack.@system[0]=system
ucitrack.@system[0].init=led
ucitrack.@system[0].affects=luci_statistics
ucitrack.@luci_splash[0]=luci_splash
ucitrack.@luci_splash[0].init=luci_splash
ucitrack.@upnpd[0]=upnpd
ucitrack.@upnpd[0].init=miniupnpd
ucitrack.@ntpclient[0]=ntpclient
ucitrack.@ntpclient[0].init=ntpclient
ucitrack.@samba[0]=samba
ucitrack.@samba[0].init=samba
ucitrack.@tinyproxy[0]=tinyproxy
ucitrack.@tinyproxy[0].init=tinyproxy
uhttpd.main=uhttpd
uhttpd.main.listen_http=0.0.0.0:80
uhttpd.main.listen_https=0.0.0.0:443
uhttpd.main.home=/www
uhttpd.main.rfc1918_filter=1
uhttpd.main.max_requests=3
uhttpd.main.cert=/etc/uhttpd.crt
uhttpd.main.key=/etc/uhttpd.key
uhttpd.main.cgi_prefix=/cgi-bin
uhttpd.main.script_timeout=60
uhttpd.main.network_timeout=30
uhttpd.main.tcp_keepalive=1
uhttpd.px5g=cert
uhttpd.px5g.days=730
uhttpd.px5g.bits=1024
uhttpd.px5g.country=DE
uhttpd.px5g.state=Berlin
uhttpd.px5g.location=Berlin
uhttpd.px5g.commonname=OpenWrtroot@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Sat Mar 15 11:29:43 CET 2014
[ 0.000000] prom: fw_arg0=00000001, fw_arg1=01f57fb0, fw_arg2=01f583b0, fw_arg3=00000000
[ 0.000000] env[0]: memsize=32
[ 0.000000] env[1]: initrd_start=0x00000000
[ 0.000000] env[2]: initrd_size=0x0
[ 0.000000] env[3]: flash_start=0xBFC00000
[ 0.000000] env[4]: flash_size=0x400000
[ 0.000000] env[0]: memsize=32
[ 0.000000] env[1]: initrd_start=0x00000000
[ 0.000000] env[2]: initrd_size=0x0
[ 0.000000] env[3]: flash_start=0xBFC00000
[ 0.000000] env[4]: flash_size=0x400000
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] Ralink RT3052 id:1 rev:2 running at 320.00 MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 80258750, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=3G-6200N console=ttyS1,57600 mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),2752k(rootfs),128k@0x3e0000(cimage)ro,3648k@0x50000(firmware) rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=0004a370
[ 0.000000] Readback ErrCtl register=0004a370
[ 0.000000] Memory: 29652k/32768k available (2059k kernel code, 3116k reserved, 343k data, 176k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.010000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912)
[ 0.090000] pid_max: default: 32768 minimum: 301
[ 0.090000] Mount-cache hash table entries: 512
[ 0.100000] NET: Registered protocol family 16
[ 0.110000] MIPS: machine is Edimax 3g-6200n
[ 0.120000] gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0
[ 0.130000] gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1
[ 0.140000] gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2
[ 0.170000] bio: create slab <bio-0> at 0
[ 0.180000] Switching to clocksource MIPS
[ 0.190000] NET: Registered protocol family 2
[ 0.200000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.220000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.230000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.250000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.260000] TCP reno registered
[ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.280000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.290000] NET: Registered protocol family 1
[ 0.340000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.360000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.380000] msgmni has been set to 57
[ 0.390000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.400000] io scheduler noop registered
[ 0.410000] io scheduler deadline registered (default)
[ 0.420000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.440000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
[ 0.450000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.480000] physmap platform flash device: 00800000 at bf000000
[ 0.490000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a8
[ 0.510000] physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
[ 0.510000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.520000] Amd/Fujitsu Extended Query version 1.1.
[ 0.530000] number of CFI chips: 1
[ 0.540000] 7 cmdlinepart partitions found on MTD device physmap-flash.0
[ 0.550000] Creating 7 MTD partitions on "physmap-flash.0":
[ 0.570000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.580000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.600000] 0x000000040000-0x000000050000 : "factory"
[ 0.610000] 0x000000050000-0x000000130000 : "kernel"
[ 0.620000] 0x000000130000-0x0000003e0000 : "rootfs"
[ 0.640000] mtd: partition "rootfs" set to be root filesystem
[ 0.650000] mtd: partition "rootfs_data" created automatically, ofs=360000, len=80000
[ 0.670000] 0x000000360000-0x0000003e0000 : "rootfs_data"
[ 0.680000] 0x0000003e0000-0x000000400000 : "cimage"
[ 0.700000] 0x000000050000-0x0000003e0000 : "firmware"
[ 0.720000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 40, using 40
[ 0.740000] TCP cubic registered
[ 0.750000] NET: Registered protocol family 17
[ 0.760000] Bridge firewalling registered
[ 0.770000] 8021q: 802.1Q VLAN Support v1.8
[ 0.780000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.800000] Freeing unused kernel memory: 176k freed
[ 3.400000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 3.550000] Button Hotplug driver version 0.4.1
[ 3.800000] Registered led device: edimax:green:power
[ 3.800000] Registered led device: edimax:amber:wlan
[ 3.800000] Registered led device: edimax:blue:3g
[ 7.160000] JFFS2 notice: (395) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 8 of xref (0 dead, 3 orphan) found.
[ 8.260000] SCSI subsystem initialized
[ 8.460000] usbcore: registered new interface driver usbfs
[ 8.470000] usbcore: registered new interface driver hub
[ 8.480000] usbcore: registered new device driver usb
[ 8.960000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.000000] dwc_otg: version 2.72a 24-JUN-2008
[ 9.010000] dwc_otg: Core Release: 2.66a
[ 9.220000] dwc_otg: Periodic Transfer Interrupt Enhancement - disabled
[ 9.230000] dwc_otg: Multiprocessor Interrupt Enhancement - disabled
[ 9.240000] dwc_otg: Using DMA mode
[ 9.250000] dwc_otg: Device using Buffer DMA mode
[ 9.260000] dwc_otg dwc_otg.0: DWC OTG Controller
[ 9.270000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[ 9.280000] dwc_otg dwc_otg.0: irq 26, io mem 0x101c0000
[ 9.290000] dwc_otg: Init: Port Power? op_state=1
[ 9.300000] dwc_otg: Init: Power Port (0)
[ 9.310000] hub 1-0:1.0: USB hub found
[ 9.320000] hub 1-0:1.0: 1 port detected
[ 9.350000] Initializing USB Mass Storage driver...
[ 9.360000] usbcore: registered new interface driver usb-storage
[ 9.380000] USB Mass Storage support registered.
[ 9.710000] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 9.930000] scsi0 : usb-storage 1-1:1.3
[ 9.940000] scsi1 : usb-storage 1-1:1.4
[ 10.930000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 10.950000] scsi 1:0:0:0: Direct-Access HUAWEI TF CARD Storage 2.31 PQ: 0 ANSI: 2
[ 10.970000] sd 1:0:0:0: [sda] 7744512 512-byte logical blocks: (3.96 GB/3.69 GiB)
[ 11.000000] sd 1:0:0:0: [sda] Write Protect is off
[ 11.010000] sd 1:0:0:0: [sda] Mode Sense: 0f 00 00 00
[ 11.010000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.040000] sda: sda1
[ 11.060000] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 30.240000] EXT4-fs (sda1): recovery complete
[ 30.250000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 31.730000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d
[ 31.750000] Backport generated by backports.git backports-20140124-0-g1256d3e
[ 32.020000] cfg80211: Calling CRDA to update world regulatory domain
[ 32.040000] cfg80211: World regulatory domain updated:
[ 32.050000] cfg80211: DFS Master region: unset
[ 32.060000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 32.070000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.090000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.100000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 32.120000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 32.140000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 32.150000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 33.630000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 33.840000] PPP generic driver version 2.4.2
[ 34.340000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 34.740000] NET: Registered protocol family 24
[ 34.970000] nf_conntrack version 0.5.0 (466 buckets, 1864 max)
[ 35.620000] usbcore: registered new interface driver huawei_ether
[ 35.730000] usbcore: registered new interface driver usbserial
[ 35.750000] USB Serial support registered for generic
[ 35.760000] usbserial_generic 1-1:1.0: generic converter detected
[ 35.770000] usb 1-1: generic converter now attached to ttyUSB0
[ 35.780000] usbserial_generic 1-1:1.1: generic converter detected
[ 35.790000] usb 1-1: generic converter now attached to ttyUSB1
[ 35.810000] usbcore: registered new interface driver usbserial_generic
[ 35.820000] usbserial: USB Serial Driver core
[ 35.910000] usbcore: registered new interface driver cdc_wdm
[ 35.960000] usbcore: registered new interface driver cdc_ether
[ 36.060000] usbcore: registered new interface driver cdc_ncm
[ 36.100000] usbcore: registered new interface driver qmi_wwan
[ 36.220000] USB Serial support registered for GSM modem (1-port)
[ 36.230000] usbcore: registered new interface driver option
[ 36.240000] option: v0.7.2:USB Driver for GSM modems
[ 44.380000] device eth0.1 entered promiscuous mode
[ 44.390000] device eth0 entered promiscuous mode
[ 44.410000] br-lan: port 1(eth0.1) entered forwarding state
[ 44.420000] br-lan: port 1(eth0.1) entered forwarding state
[ 46.420000] br-lan: port 1(eth0.1) entered forwarding state
[ 58.210000] ramips-wdt: timeout value 60 must be 0 < timeout <= 40, using 40root@OpenWrt:~# cat /proc/cpuinfo
system type : Ralink RT3052 id:1 rev:2
machine : Edimax 3g-6200n
processor : 0
cpu model : MIPS 24KEc V4.12
BogoMIPS : 212.58
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
ASEs implemented : mips16 dsp
shadow register sets : 1
kscratch registers : 0
core : 0
VCED exceptions : not available
VCEI exceptions : not availableroot@OpenWrt:~# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime,size=14916k)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
/dev/sda1 on /overlay type ext4 (rw,noatime,user_xattr,barrier=1,data=ordered)
overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)root@OpenWrt:~# cat /proc/modules
option 15120 0 - Live 0x80e94000
qmi_wwan 3888 0 - Live 0x80d0b000
cdc_ncm 6240 0 - Live 0x80e84000
usb_wwan 6560 1 option, Live 0x80e80000
cdc_ether 2960 0 - Live 0x80e61000
cdc_wdm 6928 1 qmi_wwan, Live 0x80e64000
usbserial 23664 5 option,usb_wwan, Live 0x80df8000
usbnet 12016 3 qmi_wwan,cdc_ncm,cdc_ether, Live 0x80df0000
hw_cdc_driver 26480 0 - Live 0x80e68000 (O)
ledtrig_usbdev 2032 0 - Live 0x80d0c000
nf_nat_irc 816 0 - Live 0x80d7f000
nf_conntrack_irc 2480 1 nf_nat_irc, Live 0x80d08000
nf_nat_ftp 992 0 - Live 0x80d7b000
nf_conntrack_ftp 4448 1 nf_nat_ftp, Live 0x80d06000
ipt_MASQUERADE 976 1 - Live 0x80d70000
iptable_nat 2528 1 - Live 0x80d78000
nf_nat 10368 4 nf_nat_irc,nf_nat_ftp,ipt_MASQUERADE,iptable_nat, Live 0x80d00000
pppoe 7504 0 - Live 0x80d7c000
xt_conntrack 2080 3 - Live 0x80d74000
xt_CT 1216 0 - Live 0x80d72000
xt_NOTRACK 448 0 - Live 0x80d73000
iptable_raw 560 1 - Live 0x80d6e000
xt_state 608 0 - Live 0x80db8000
nf_conntrack_ipv4 4368 6 iptable_nat,nf_nat, Live 0x80d6c000
nf_defrag_ipv4 640 1 nf_conntrack_ipv4, Live 0x80db2000
nf_conntrack 38208 12 nf_nat_irc,nf_conntrack_irc,nf_nat_ftp,nf_conntrack_ftp,ipt_MASQUERADE,iptable_nat,nf_nat,xt_conntrack,xt_CT,xt_NOTRACK,xt_state,nf_conntrack_ipv4, Live 0x80d60000
pppox 1152 1 pppoe, Live 0x80d1a000
ipt_REJECT 1680 2 - Live 0x80db7000
xt_TCPMSS 2560 1 - Live 0x80db0000
ipt_LOG 6096 0 - Live 0x80db4000
xt_comment 400 99 - Live 0x80d14000
xt_multiport 1120 0 - Live 0x80d16000
xt_mac 528 0 - Live 0x80e5c000
xt_limit 944 1 - Live 0x80e5e000
iptable_mangle 816 1 - Live 0x80e5d000
iptable_filter 592 1 - Live 0x80e57000
ip_tables 9424 4 iptable_nat,iptable_raw,iptable_mangle,iptable_filter, Live 0x80d10000
xt_tcpudp 1616 84 - Live 0x80cf4000
x_tables 9984 18 ipt_MASQUERADE,iptable_nat,xt_conntrack,xt_CT,xt_NOTRACK,iptable_raw,xt_state,ipt_REJECT,xt_TCPMSS,ipt_LOG,xt_comment,xt_multiport,xt_mac,xt_limit,iptable_mangle,iptable_filter,ip_tables,xt_tcpudp, Live 0x80e58000
ppp_async 5984 1 - Live 0x80d5e000
ppp_generic 18880 7 pppoe,pppox,ppp_async, Live 0x80e50000
slhc 4144 1 ppp_generic, Live 0x80d1c000
vfat 7728 0 - Live 0x80d42000
fat 41376 1 vfat, Live 0x80d50000
nls_iso8859_1 2800 0 - Live 0x80d47000
nls_cp437 4336 0 - Live 0x80d40000
rt2x00lib 29808 0 - Live 0x80d48000 (O)
mac80211 318544 1 rt2x00lib, Live 0x80e00000 (O)
crc_itu_t 944 0 - Live 0x80d44000
crc_ccitt 944 1 ppp_async, Live 0x80cf2000
eeprom_93cx6 1632 0 - Live 0x80ceb000
cfg80211 184496 2 rt2x00lib,mac80211, Live 0x80d80000 (O)
compat 7376 2 mac80211,cfg80211, Live 0x80cf6000 (O)
arc4 768 0 - Live 0x80cf1000
aes_generic 29600 0 - Live 0x80cf8000
usb_storage 32880 1 - Live 0x80cc0000
dwc_otg 58592 0 - Live 0x80c70000
ehci_hcd 29296 0 - Live 0x80c38000
sd_mod 22784 2 - Live 0x81b80000
ext4 230144 1 - Live 0x80c80000
jbd2 37776 1 ext4, Live 0x80c10000
mbcache 3504 1 ext4, Live 0x81bab000
usbcore 97456 14 option,qmi_wwan,cdc_ncm,usb_wwan,cdc_ether,cdc_wdm,usbserial,usbnet,hw_cdc_driver,ledtrig_usbdev,usb_storage,dwc_otg,ehci_hcd, Live 0x80c40000
usb_common 480 1 usbcore, Live 0x81bd7000
scsi_mod 69856 2 usb_storage,sd_mod, Live 0x80c20000
nls_base 4672 5 vfat,fat,nls_iso8859_1,nls_cp437,usbcore, Live 0x81b46000
crc16 944 1 ext4, Live 0x81b78000
crypto_algapi 9216 2 arc4,aes_generic, Live 0x81b74000
leds_gpio 1552 0 - Live 0x81b6a000
button_hotplug 2688 0 - Live 0x81bf2000 (O)
gpio_keys_polled 2064 0 - Live 0x81bda000
input_polldev 1696 1 gpio_keys_polled, Live 0x81b40000
input_core 20000 4 button_hotplug,gpio_keys_polled,input_polldev, Live 0x81ba0000Strony 1
eko.one.pl → Posty przez jacekdob
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc