I have tried all the ways, it seems that there is no way to recover and I have to think about a new router.
In any case, your answers are very valuable for me.
Thanks
Strony 1
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Posty przez hossein.a67
Strony 1
I have tried all the ways, it seems that there is no way to recover and I have to think about a new router.
In any case, your answers are very valuable for me.
Thanks
The previous problem was solved with your help. Now a new problem!
When the router boots, it doesn't allow me to select options and immediately selects option 3 by default.
U-Boot 1.1.3 (Apr 15 2016 - 17:46:32)
Board: Ralink APSoC DRAM: 128 MB
Power on memory test. Memory size= 128 MB...OK!
relocate_code Pointer at: 87fb8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
!!! nand page size = 2048, addr len=4
..============================================
Ralink UBoot Version: 4.2.S.1
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM_CONF_FROM: Auto-detection
DRAM_TYPE: DDR2
DRAM component: 1024 Mbits
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: NAND Flash
Date:Apr 15 2016 Time:17:46:32
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =128 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
3: System Boot system code via Flash.
Booting System 2
..ranand_erase_write: offs:40000, count:20000
.Done!
done
## Booting image at bc600000 ...
Image Name: MIPS OpenWrt Linux-4.14.89
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1596367 Bytes = 1.5 MB
Load Address: 80000000
Entry Point: 80000000
......................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
commandline uart_en=0 factory_mode=0 mem=128m
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128
Starting kernel ...
[ 0.000000] Linux version 4.14.89 (ador@ubuntu) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7365-95daf4c441)) #0 Tue Dec 18 17:25:50 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6And this part is displayed endlessly
[ 0.000000] Linux version 4.14.89 (ador@ubuntu) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7365-95daf4c441)) #0 Tue Dec 18 17:25:50 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6Thank you for your reply. So I will get a cp2102 usb to ttl and try again.
Connections are good.
I use rs232 to connect (TXD,RXD and GND pins) , could this be the problem?
Hi, I can't unbrick my xiaomi router 3. I followed all your instructions carefully, but unfortunately it didn't work. Can you guide me? Also I could not download the kernel0.bin file, Link is dead.
This image is my last result:
https://ibb.co/qJ9yNg1
Thankful
Strony 1
eko.one.pl → Posty przez hossein.a67
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc