Wpisz w przeglądarkę 192.168.31.1i zobacz czy się łączysz
Strony 1
Nie jesteś zalogowany. Proszę się zalogować lub zarejestrować.
eko.one.pl → Posty przez jurekcostam
Strony 1
Wpisz w przeglądarkę 192.168.31.1i zobacz czy się łączysz
Cezary napisał/a:Tak, wgranie nowego softu przez tftp.
CZy możesz mnie poinstruować jak użyć ten uart do ax3600 https://www.amazon.pl/dp/B07WX2DSVB?psc … ct_details
A próbowałeś MIWIFIRepairTool https://forum.openwrt.org/t/xiaomi-mi-r … 6?u=mikeeq
Mi tym udało się postawić router do życia
uci set system.@system[0].compat_version="1.0" uci commit system
Jeszcze mam pytanie (z reszta mam ich więcej).
Czy po aktualizacji trzeba odinstalować "wpad-basic-wolfssl" i zainstalować "wpad-wolfssl"
I później już sysupgrade -n .... ?
Możesz napisać jak to zrobić chodzi o polecenia. Jeżeli chodzi o Luci to wiem bo już robiłem aktualizację sysupgrade i wcześniej poszło
Nie wiem czy mogę mam już zrobioną poszerzaną partycje.
Poprzednio miałem obraz @robimako ten z 14stycznia, później zainstalowałem ze strony OpenWrt zainstalował się z wymuszeniem. Tego najnowszego z OpenWrt już nie mogę.
Witam
mam zainstalowany obraz SNAPSHOT r21922-6e428a8490 z LuCI chciałem zrobić aktualizację ale wywali mi bład:
root@OpenWrt:~# sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashf
s-sysupgrade.bin
Mon Jan 30 17:31:30 CET 2023 upgrade: The device is supported, but this image is incompatible for sysupgrade based on the image version (2.0->1.0).
Image check failed.
root@OpenWrt:~#
Próbowałem też aktualizację firmware przez LuCI ale też nie można ten sam błąd.
Nawet jak dam" wymuś uaktualnienie" niby obraz się ładuje ale po restarcie wstaje nadal bierzący obraz.
Coś robię nie tak?
Daje (dawało), 16 miesięcy temu bez problemów, tylko przed montażem trzeba zgłosić.
Witam.
Jak instaluje openwrt mam takie coś
root@XiaoQiang:~# ubiformat /dev/mtd13 -f /tmp/openwrt-ipq807x-generic-xiaomi_ax
3600-squashfs-nand-factory.ubi -s 2048 -O 2048
ubiformat: mtd13 (nand), size 37486592 bytes (35.7 MiB), 286 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
libscan: scanning eraseblock 285 -- 100 % complete
ubiformat: 216 eraseblocks have valid erase counter, mean value is 0
ubiformat: 70 eraseblocks are supposedly empty
ubiformat: warning!: only 216 of 286 eraseblocks have valid erase counter
ubiformat: mean erase counter 0 will be used for the rest of eraseblockjest czym się przejmować?
Jeszcze takie pytanie.
Przy reanimacji pod Linuxem
sudo ip address flush dev <adapter name><adapter name> co tu wpisać?
Czy według tego
2: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:80:64:a7:xx:xx brd ff:ff:ff:ff:ff:ff
inet 192.168.1.55/24 brd 192.168.1.255 scope global noprefixroute enp4s0będzie to enp4s0?
Jest sukces.
Udało się go postawić MIWIFIRepairTool.
Poszło od strzała.
Przy wyłączonym antywirusie to samo.
Co i jak ustawić w TFTPd64e tu może być problem że nie potrafię tego ustawić jak należy.
Ok gdzie popełniam błąd?
Pobrałem soft xiaoqiang/rom/r3600/miwifi_r3600_firmware_5da25_1.0.17.bin.
Zmieniłem nazwę na C0A81F02.img
Wrzucam do katalogu z TFTP.
Ustawiłem stałe ip na kompie
Połączyłem kompa z routerem po LAN
Ustawiłęm w TFTP Current Directory ścieżka do katalogu TTFTP, Serwer Interfaces ustawiłem kartę z IP 192.168.31.100
trzymam reset w routera, włączam zasilanie, dioda świeci na pomarańczowo, zaczyna mrugać puszczam przycisk.
I Nic dostaje takiego loga ( teraz wleje całego)
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAACANAAA
S - OEM_IMAGE_VERSION_STRING=xiaoyang-gv
S - Boot Config, 0x000002e5
B - 203 - PBL, Start
B - 2739 - bootable_media_detect_entry, Start
B - 3447 - bootable_media_detect_success, Start
B - 3451 - elf_loader_entry, Start
B - 6121 - auth_hash_seg_entry, Start
B - 6368 - auth_hash_seg_exit, Start
B - 68630 - elf_segs_hash_verify_entry, Start
B - 131331 - PBL, End
B - 139202 - SBL1, Start
B - 190381 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B - 196664 - pm_device_init, Start
B - 315156 - PM_SET_VAL:Skip
D - 117974 - pm_device_init, Delta
B - 317474 - pm_driver_init, Start
D - 5368 - pm_driver_init, Delta
B - 323940 - clock_init, Start
D - 2135 - clock_init, Delta
B - 327905 - boot_flash_init, Start
D - 11864 - boot_flash_init, Delta
B - 343552 - boot_config_data_table_init, Start
D - 3202 - boot_config_data_table_init, Delta - (575 Bytes)
B - 351085 - Boot Setting : 0x00000600
B - 355020 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16
B - 361943 - sbl1_ddr_set_params, Start
B - 365756 - CPR configuration: 0x300
B - 369141 - cpr_init, Start
B - 372039 - Rail:0 Mode: 5 Voltage: 824000
B - 377163 - CL CPR settled at 776000mV
B - 379999 - Rail:1 Mode: 5 Voltage: 880000
B - 384178 - Rail:1 Mode: 7 Voltage: 928000
D - 16470 - cpr_init, Delta
B - 391071 - Pre_DDR_clock_init, Start
B - 395097 - Pre_DDR_clock_init, End
B - 398482 - DDR Type : PCDDR3
B - 404186 - do ddr sanity test, Start
D - 1067 - do ddr sanity test, Delta
B - 408944 - DDR: Start of HAL DDR Boot Training
B - 413671 - DDR: End of HAL DDR Boot Training
B - 419344 - DDR: Checksum to be stored on flash is -31203832
B - 429653 - Image Load, Start
D - 224084 - QSEE Image Loaded, Delta - (1373936 Bytes)
B - 653828 - Image Load, Start
D - 30 - SEC Image Loaded, Delta - (0 Bytes)
B - 661514 - Image Load, Start
D - 10736 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B - 672342 - Image Load, Start
D - 25254 - RPM Image Loaded, Delta - (105964 Bytes)
B - 697657 - Image Load, Start
D - 96563 - APPSBL Image Loaded, Delta - (589900 Bytes)
B - 794311 - QSEE Execution, Start
D - 61 - QSEE Execution, Delta
B - 800106 - USB D+ check, Start
D - 0 - USB D+ check, Delta
B - 806511 - SBL1, End
D - 669627 - SBL1, Delta
S - Flash Throughput, 6752 KB/s (2096379 Bytes, 310451 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 800 MHz
U-Boot 2016.01 (Sep 28 2020 - 09:05:55 +0000), Build: jenkins-common_router_openwrt_ota_publish-383
DRAM: smem ram ptable found: ver: 1 len: 4
512 MiB
NAND: ONFI device found
ID = 1590aac8
Vendor = c8
Device = aa
qpic_nand: changing oobsize to 64 from 128 bytes
SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
256 MiB
MMC: sdhci: Node Not found, skipping initialization
PCI Link Intialized
PCI1 is not defined in the device tree
In: serial@78B3000
Out: serial@78B3000
Err: serial@78B3000
machid: 8010010
MMC Device 0 not found
eth5 MAC Address from ART is not valid
write phy_id=1, reg(0x8074):0x0670
write phy_id=2, reg(0x8074):0x0670
write phy_id=3, reg(0x8074):0x0670
write phy_id=4, reg(0x8074):0x0670
bootwait is on, bootdelay=5
Hit any key to stop autoboot: 0
detect button press, continue check 5 secs
detect button pressed 5 secs !
confirm to launch xq_upgrade !
cmd=dhcp
Net: MAC0 addr:9c:9d:7e:75:35:b6
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
board_eth_init: ipq807x_edma_init successed
eth0
ipq807x_eth_halt: done
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 up Speed :10 Full duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 up Speed :1000 Full duplex
eth0 PHY4 Down Speed :10 Half duplex
eth0 PHY5 Down Speed :10 Half duplex
ipq807x_eth_init: done
BOOTP broadcast 1
BOOTP broadcast 2czy tak jest ok. Wgrywa się?
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
board_eth_init: ipq807x_edma_init successed
eth0
ipq807x_eth_halt: done
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 up Speed :10 Full duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
eth0 PHY5 Down Speed :10 Half duplex
ipq807x_eth_init: done
BOOTP broadcast 1
BOOTP broadcast 2Wgraj soft po prostu?
Nie bardzo wiem jak mogę prosić o napisanie jak?
Można to jakoś naprawić?
mogę całego loga wstawić jak trzeba
ok już mam połaczenie ale dochodzi do pewnego momentu i koniec
[ 1.661212] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[ 1.670311] ubi0: attaching mtd12
[ 1.828847] ubi0: scanning is finished
[ 1.834640] ubi0: attached mtd12 (name "rootfs", size 35 MiB)
[ 1.834679] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.839389] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.846143] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.853015] ubi0: good PEBs: 286, bad PEBs: 0, corrupted PEBs: 0
[ 1.859774] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 1.866023] ubi0: max/mean erase counter: 9/7, WL threshold: 4096, image sequence number: 535767059
[ 1.873063] ubi0: available PEBs: 3, total reserved PEBs: 283, PEBs reserved for bad PEB han▒[ 1.891611] Waiting for root device /dev/ubiblock0_1...
[ 32.489194] l11: disablingnie wiem co może być?
Panowie co robię nie tak?
Konwerter CH 340 podłączony do USB Jest wykryty jako COM4. Konwerter połączony z routerem GND-GND RX-TX TX-RX.
IP w karcie eternet ustawione na 192.168.31.100. W TFTP ustawione Katalog z TFTP64 w nim jet plik z firware Serwer interfaces 192.168.31.100 z karą eternet.
Wciskam reste właczam zasilanie.
Migną diody i koniec nic się nie dzieje.
Gdzie popełniam błąd?
Edit:
teraz mam też błąd z tftp:
Error 10049 żądany adres jest nieprawidłowy w tym kontekcie . Tftpd32 tried to
bind the tftp portto the interface 192.168.31.100 which is not available for this
host Either remove the tftp service or suppress 192.168.31.100 interface assignationNo właśnie określony adres IP.
Czy to jest dowolny z puli 192.168.1.x
Czy jakiś ściśle określony?
Wgraj oryginalny soft przez tftp: https://openwrt.org/inbox/toh/xiaomi/xi … debricking i przełącz znów na openwrt.
A czy mogę prosić o jakieś instrukcję jak to zrobić z pod Windowsa.
A takie pytanie może trochę nie w temacie .
Czy połączenia może być konwerter CH341a czy musi być CH340 lub CP2102?
No to uwaliłem router.
Świeci tylko pomarańczowa dioda system.
Mogę prosić o jakieś wskazówki jak go przywrócić do życia
Takie pytanie laika.
Skąd można pobrać pliki openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-nand-factory.ubi (i bin)
Strony 1
eko.one.pl → Posty przez jurekcostam
Forum oparte o PunBB, wspierane przez Informer Technologies, Inc