U-Boot 1.1.3 (Apr 15 2016 - 17:46:32)

Board: Ralink APSoC DRAM:  128 MB
Power on memory test. Memory size= 128 MB...OK!
relocate_code Pointer at: 87fb8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
!!! nand page size = 2048, addr len=4
..============================================
Ralink UBoot Version: 4.2.S.1
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM_CONF_FROM: Auto-detection
DRAM_TYPE: DDR2
DRAM component: 1024 Mbits
DRAM bus: 16 bit
Total memory: 128 MBytes
Flash component: NAND Flash
Date:Apr 15 2016  Time:17:46:32
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size =128 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP.


3: System Boot system code via Flash.
Booting System 2
..ranand_erase_write: offs:40000, count:20000
.Done!
done
## Booting image at bc600000 ...
   Image Name:   MIPS LEDE Linux-4.9.65
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1386594 Bytes =  1.3 MB
   Load Address: 80000000
   Entry Point:  80000000
......................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
commandline uart_en=0 factory_mode=0 mem=128m
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128

Starting kernel ...

[    0.000000] Linux version 4.9.65 (terminator@SC-GAME) (gcc version 6.3.0 (LEDE GCC 6.3.0 r5347-74ed981) ) #0 Tue Nov 28 22:33:46 2017
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Xiaomi Mi Router R3
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=0000000b
[    0.000000] Readback ErrCtl register=0000000b
[    0.000000] Memory: 125396K/131072K available (3435K kernel code, 161K rwdata, 440K rodata, 180K init, 220K bss, 5676K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.007575] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.070070] pid_max: default: 32768 minimum: 301
[    0.074681] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.081050] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090549] devtmpfs: initialized
[    0.098348] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.107887] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.113846] pinctrl core: initialized pinctrl subsystem
[    0.119547] NET: Registered protocol family 16
[    0.128638] Can't analyze schedule() prologue at 80357340
[    0.608844] PCI host bridge /pcie@10140000 ranges:
[    0.613453]  MEM 0x0000000020000000..0x000000002fffffff
[    0.618505]   IO 0x0000000010160000..0x000000001016ffff
[    0.637787] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.643181] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.649689] rt2880_gpio 10000638.gpio: registering 16 gpios
[    0.655067] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[    0.661937] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.667322] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.674708] PCI host bridge to bus 0000:00
[    0.678640] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    0.685368] pci_bus 0000:00: root bus resource [io  0xffffffff]
[    0.691054] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.697659] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.705790] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.714299] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    0.720664] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    0.727478] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    0.734022] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[    0.741052] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    0.747637] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[    0.754766] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[    0.761742] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.766578] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    0.773155] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
[    0.780202] pci 0000:00:00.0: card - bus=0x0, slot = 0x0 irq=0
[    0.785838] pci 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
[    0.794748] clocksource: Switched to clocksource systick
[    0.803348] NET: Registered protocol family 2
[    0.808501] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.815285] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.821410] TCP: Hash tables configured (established 1024 bind 1024)
[    0.827684] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.833306] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.839687] NET: Registered protocol family 1
[    0.845769] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.852369] Crashlog allocated RAM at address 0x3f00000
[    0.858650] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.872944] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.878597] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.897491] io scheduler noop registered
[    0.901238] io scheduler deadline registered (default)
[    0.906591] ralink-usb-phy usbphy: invalid resource
[    0.912755] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.921046] console [ttyS0] disabled
[    0.924491] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.934181] console [ttyS0] enabled
[    0.934181] console [ttyS0] enabled
[    0.941215] bootconsole [early0] disabled
[    0.941215] bootconsole [early0] disabled
[    0.950888] !!! nand page size = 2048, addr len=4
[    0.956464] mtk_nand_probe: alloc 1390, at 87c96000 , btt(87c970c0, 100), ranfc_mtd:87c971c0
[    0.965462] 10 ofpart partitions found on MTD device ra_nfc
[    0.971155] Creating 10 MTD partitions on "ra_nfc":
[    0.976199] 0x000000000000-0x000000040000 : "Bootloader"
[    0.983696] 0x000000040000-0x000000080000 : "Config"
[    0.991232] 0x000000080000-0x0000000c0000 : "Bdata"
[    0.998690] 0x0000000c0000-0x000000100000 : "Factory"
[    1.006299] 0x000000100000-0x000000140000 : "crash"
[    1.013645] 0x000000140000-0x000000180000 : "crash_syslog"
[    1.021690] 0x000000180000-0x000000200000 : "reserved0"
[    1.029546] 0x000000200000-0x000000600000 : "kernel0_rsvd"
[    1.038843] 0x000000600000-0x000000a00000 : "kernel"
[    1.047613] 0x000000a00000-0x000008000000 : "ubi"
[    1.081507] _nfc_read_raw_data: fail
[    1.085252] nfc_read_oob: fail
[    1.088368] nand_block_checkbad: offs:6000000 tag: BAD
[    1.107416] libphy: Fixed MDIO Bus: probed
[    1.113781] gsw: setting port4 to ephy mode
[    1.118618] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    1.125515] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    1.137035] rt2880_wdt 10000120.watchdog: Initialized
[    1.143369] NET: Registered protocol family 10
[    1.150584] NET: Registered protocol family 17
[    1.155259] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.168503] 8021q: 802.1Q VLAN Support v1.8
[    1.177037] UBI: auto-attach mtd9
[    1.180457] ubi0: attaching mtd9
[    1.599903] nand_block_checkbad: offs:6000000 tag: BAD
[    1.757867] ubi0: scanning is finished
[    1.772991] ubi0: attached mtd9 (name "ubi", size 118 MiB)
[    1.778665] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.785696] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.792622] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.799739] ubi0: good PEBs: 943, bad PEBs: 1, corrupted PEBs: 0
[    1.805884] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
[    1.813258] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1605569827
[    1.822589] ubi0: available PEBs: 920, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
[    1.832710] ubi0: background thread "ubi_bgt0d" started, PID 289
[    1.839314] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.847023] Please append a correct "root=" boot option; here are the available partitions:
[    1.855567] 1f00             256 mtdblock0 [    1.859654]  (driver?)
[    1.862065] 1f01             256 mtdblock1 [    1.866161]  (driver?)
[    1.868574] 1f02             256 mtdblock2 [    1.872658]  (driver?)
[    1.875083] 1f03             256 mtdblock3 [    1.879169]  (driver?)
[    1.881578] 1f04             256 mtdblock4 [    1.885675]  (driver?)
[    1.888088] 1f05             256 mtdblock5 [    1.892172]  (driver?)
[    1.894581] 1f06             512 mtdblock6 [    1.898679]  (driver?)
[    1.901092] 1f07            4096 mtdblock7 [    1.905191]  (driver?)
[    1.907604] 1f08            4096 mtdblock8 [    1.911688]  (driver?)
[    1.914098] 1f09          120832 mtdblock9 [    1.918196]  (driver?)
[    1.920608] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    1.930735] Rebooting in 1 seconds..


U-Boot 1.1.3 (Apr 15 2016 - 17:46:32)