FAQ o OpenWrt | Sprzedam różne routery | Oddam

2022-08-18 10:05:21

VID/PID looks like an AT1, please use double ‘ instead of “, otherwise command is not sent

Do also a:

dmesg | grep QCA
dmesg | grep IPQ

Thx

2022-08-17 16:59:05

MiG25 napisał/a:

... i od razu cat sys/kernel/debug/usb/devices
Po tym też można próbować rozróżniać wersje

But the serial number is equal for all version, may be we just distinguish them with VID/PID for T1/T2 revision

2022-08-17 16:52:10

MiG25 napisał/a:

stich86 napisał/a:
Cool… we should found ZTE framework for this modem…
Do you have framework for this version?

No, I’m trying to find it…

I should try to see if modem module can be flashed using “dd” dump, so we can upgrade to latest version available

@smereka can you check the version of the modem?

On stock firmare run:

cat /dev/ttyUSB2 &
echo -e “ATI\r” > /dev/ttyUSB2

Thx

2022-08-17 15:49:17

smereka napisał/a:

stich, or what is this version with problematic wifi at 80MHz or the correct one?

Fixed
I’ve put correct board data for AT2

2022-08-17 15:12:32

smereka napisał/a:

Na razie bez patroszenia to pokazuje OFW:

Cool… we should found ZTE framework for this modem…

2022-08-17 12:17:31

Leo-PL napisał/a:

Calibration of ath10k is a bit like walking in the darkness, because it is result of data from board-2.bin, pre-cal data on flash AND OTP data per unit, with no decoder of board files into plaintext. Both are essentially key-value stores. atheepmgr shows very little data about ath10k due to this.
Still, I would not worry about the power as much, the fact that board-2.bin is extracted from right firmware is more important, and PR on Github needs to be updated.

understood..
i've update the PR changing also the ipq-wifi package to add custom board-2.bin, till ath10k is updated

2022-08-17 12:15:32

MiG25 napisał/a:

Co do usb ,to probowalem sie wlutowac w złącze microusb ,ale bez sukcesu.
Znaczy wlut się udal ale ,nie ma ani 5v ,ani nic się nie dzieje.
Technologia PCB tez nie ulatwia sprawy ,bo nie widać za wiele ścieżek.

but you have said before that there is no signal on that pad..
Does it make sense to solder the port?

2022-08-17 11:52:30

smereka napisał/a:

Dzisiaj być może dzięki uprzejmości znajomego będę miał na jakiś czas (a może i na zawsze) do testów wersję z t-mobile. Mam zgodę na wypatroszenie Ciężko się go rozbiera? Jakieś wskazówki żeby zrobić to jak najmniej inwazyjnie?

nice.. yes pls share mtd16 and mtd17

you can found here the instruction to backup partition:

https://github.com/openwrt/openwrt/pull … f9d2719f26

here you have a guide to open it (sorry for Italian):

https://forum.fibra.click/d/32421-zte-m … dello-vfit

If you need a test build with working and corrected wifi calibration (both AT1 and AT2 revs), you can find new one here:

https://github.com/stich86/OpenWRT-ZTE- … ild_220817

let us know

2022-08-17 09:57:32

MiG25 napisał/a:

And low power also compared to MF286D?

looks like also MF286D has same power behaviour.

2022-08-16 21:00:24

Ok you were right Leo-PL.

I did the board-2.bin using 5G boardData from my dump (AT1). Looks like that this file differ from an AT2 version.

New version with correct board data reach same speed of MF286D

But the power seems low compared to stock OFW..

2022-08-16 14:59:58

Leo-PL napisał/a:

Yeah, VHT-NSS 1, so single spatial stream is used. Strange, to say the least. Isn't this caused by mixed-up contents for board-2.bin extracted from AT1 vs AT2? I'd re-do the extraction or slap in the data from MF286D to see if it helps - of course just to confirm the suspicion.

ATM two tests was done:

- board-2.bin using extracted data from VFIT rom (I’ll try to create it from VFDE/Rev AT2)
- board-2.bin stock, so it’s using “random” board-id=21 (not sure the one from MF286D)

On both tests VHT-NSS was 1

I’ll try later and let you know

2022-08-16 14:03:47

Leo-PL napisał/a:

While testing, I bet you can see 'VHT-MCS 9' and 'VHT-NSS 1' in LuCI for your stattion during high traffic - am I right?

this is a binding on AT2 version shown on LuCI, as you can see it's 433mbit/s@80mhz

while this one is on MF286D (same radios on IPQ4019):

2022-08-16 13:45:45

this is 'iw list' from AT1 (QCA9984):

Wiphy phy4
wiphy index: 4
max # scan SSIDs: 16
max scan IEs length: 195 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
* P2P-device
Band 1:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x339959b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
VHT extended NSS: not supported
Frequencies:
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
valid interface combinations:
* #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Maximum associated stations in AP mode: 32
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
Wiphy phy3
wiphy index: 3
max # scan SSIDs: 16
max scan IEs length: 199 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
* P2P-device
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
VHT Capabilities (0x339a79fa):
Max MPDU length: 11454
Supported Channel Width: 160 MHz, 80+80 MHz
RX LDPC
short GI (80 MHz)
short GI (160/80+80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 1560 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 1560 Mbps
VHT extended NSS: not supported
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (24.0 dBm) (radar detection)
* 5280 MHz [56] (24.0 dBm) (radar detection)
* 5300 MHz [60] (24.0 dBm) (radar detection)
* 5320 MHz [64] (24.0 dBm) (radar detection)
* 5500 MHz [100] (24.0 dBm) (radar detection)
* 5520 MHz [104] (24.0 dBm) (radar detection)
* 5540 MHz [108] (24.0 dBm) (radar detection)
* 5560 MHz [112] (24.0 dBm) (radar detection)
* 5580 MHz [116] (24.0 dBm) (radar detection)
* 5600 MHz [120] (24.0 dBm) (radar detection)
* 5620 MHz [124] (24.0 dBm) (radar detection)
* 5640 MHz [128] (24.0 dBm) (radar detection)
* 5660 MHz [132] (24.0 dBm) (radar detection)
* 5680 MHz [136] (24.0 dBm) (radar detection)
* 5700 MHz [140] (24.0 dBm) (radar detection)
* 5720 MHz [144] (24.0 dBm) (radar detection)
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
* 5845 MHz [169] (27.0 dBm) (no IR)
* 5865 MHz [173] (27.0 dBm) (no IR)
valid interface combinations:
* #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1,
total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Maximum associated stations in AP mode: 32
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support

and this is from AT2

Wiphy phy1
wiphy index: 1
max # scan SSIDs: 16
max scan IEs length: 199 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
   * IBSS
   * managed
   * AP
   * AP/VLAN
   * monitor
   * mesh point
   * P2P-client
   * P2P-GO
   * P2P-device
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x339959b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
VHT extended NSS: not supported
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (24.0 dBm) (radar detection)
* 5280 MHz [56] (24.0 dBm) (radar detection)
* 5300 MHz [60] (24.0 dBm) (radar detection)
* 5320 MHz [64] (24.0 dBm) (radar detection)
* 5500 MHz [100] (24.0 dBm) (radar detection)
* 5520 MHz [104] (24.0 dBm) (radar detection)
* 5540 MHz [108] (24.0 dBm) (radar detection)
* 5560 MHz [112] (24.0 dBm) (radar detection)
* 5580 MHz [116] (24.0 dBm) (radar detection)
* 5600 MHz [120] (24.0 dBm) (radar detection)
* 5620 MHz [124] (24.0 dBm) (radar detection)
* 5640 MHz [128] (24.0 dBm) (radar detection)
* 5660 MHz [132] (24.0 dBm) (radar detection)
* 5680 MHz [136] (24.0 dBm) (radar detection)
* 5700 MHz [140] (24.0 dBm) (radar detection)
* 5720 MHz [144] (24.0 dBm) (radar detection)
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
* 5845 MHz [169] (27.0 dBm) (no IR)
* 5865 MHz [173] (27.0 dBm) (no IR)
valid interface combinations:
   * #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1,
   total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
   * MCS: ff ff ff ff ff ff ff ff ff ff
   * maximum A-MSDU length
   * supported channel width
   * short GI for 40 MHz
   * max A-MPDU length exponent
   * min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Maximum associated stations in AP mode: 32
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 16
max scan IEs length: 195 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
   * IBSS
   * managed
   * AP
   * AP/VLAN
   * monitor
   * mesh point
   * P2P-client
   * P2P-GO
   * P2P-device
Band 1:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x339959b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
VHT extended NSS: not supported
Frequencies:
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
valid interface combinations:
   * #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1,
   total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
   * MCS: ff ff ff ff ff ff ff ff ff ff
   * maximum A-MSDU length
   * supported channel width
   * short GI for 40 MHz
   * max A-MPDU length exponent
   * min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Maximum associated stations in AP mode: 32
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support

This is also an output from MF286D, that should use same configuration for AT2 rev

Wiphy phy1
wiphy index: 1
max # scan SSIDs: 16
max scan IEs length: 199 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
   * IBSS
   * managed
   * AP
   * AP/VLAN
   * monitor
   * mesh point
   * P2P-client
   * P2P-GO
   * P2P-device
Band 2:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x339959b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (20.0 dBm) (radar detection)
* 5280 MHz [56] (20.0 dBm) (radar detection)
* 5300 MHz [60] (20.0 dBm) (radar detection)
* 5320 MHz [64] (20.0 dBm) (radar detection)
* 5500 MHz [100] (26.0 dBm) (radar detection)
* 5520 MHz [104] (26.0 dBm) (radar detection)
* 5540 MHz [108] (26.0 dBm) (radar detection)
* 5560 MHz [112] (26.0 dBm) (radar detection)
* 5580 MHz [116] (26.0 dBm) (radar detection)
* 5600 MHz [120] (26.0 dBm) (radar detection)
* 5620 MHz [124] (26.0 dBm) (radar detection)
* 5640 MHz [128] (26.0 dBm) (radar detection)
* 5660 MHz [132] (26.0 dBm) (radar detection)
* 5680 MHz [136] (26.0 dBm) (radar detection)
* 5700 MHz [140] (26.0 dBm) (radar detection)
* 5720 MHz [144] (13.0 dBm) (radar detection)
* 5745 MHz [149] (13.0 dBm)
* 5765 MHz [153] (13.0 dBm)
* 5785 MHz [157] (13.0 dBm)
* 5805 MHz [161] (13.0 dBm)
* 5825 MHz [165] (13.0 dBm)
* 5845 MHz [169] (13.0 dBm)
* 5865 MHz [173] (13.0 dBm)
valid interface combinations:
   * #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1,
   total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
   * MCS: ff ff ff ff ff ff ff ff ff ff
   * maximum A-MSDU length
   * supported channel width
   * short GI for 40 MHz
   * max A-MPDU length exponent
   * min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Maximum associated stations in AP mode: 32
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 16
max scan IEs length: 195 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
   * IBSS
   * managed
   * AP
   * AP/VLAN
   * monitor
   * mesh point
   * P2P-client
   * P2P-GO
   * P2P-device
Band 1:
Capabilities: 0x19ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x339959b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
MU Beamformer
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
valid interface combinations:
   * #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1,
   total <= 16, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz, 80 MHz, 80+80 MHz, 160 MHz }
HT Capability overrides:
   * MCS: ff ff ff ff ff ff ff ff ff ff
   * maximum A-MSDU length
   * supported channel width
   * short GI for 40 MHz
   * max A-MPDU length exponent
   * min MPDU start spacing
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Maximum associated stations in AP mode: 32
Supported extended features:
* [ VHT_IBSS ]: VHT-IBSS
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ DEL_IBSS_STA ]: deletion of IBSS station support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support

2022-08-16 10:25:46

MiG25 napisał/a:

Simplest way is that 433Mbps is for Channel 40Mhz ,and 866Mbps is 80Mhz.
What kind of wideband show WiFiAnalizer (apk on android)?

Yes I know, but fix it at 80Mh, near to the router the connection speed is reported as 433Mbit/s

2022-08-15 21:45:17

any suggestion for debug 5Ghz (IPQ4019) issue?
Looks like that on MF289F the WiFi is worse compared to MF286D (that is using same chip).

For instance a client on MF289F (using board-2.bin created by stock boardData) gives only max 433Mbit/s (near the router), while on MF286D same client can go up to 866Mbit/s.

May be i've missed something...

AT1 with QCA9984 has no problem

thanks!

2022-08-13 15:10:01

IceG napisał/a:

stich86 napisał/a:
@4IceG do you know why the app for connection monitor doesn't give +x permission to file lite_watchdog*/lite-watchdog*?
Also.. how to force ttyUSB to USB1 on your package? So I can avoid each time to manually modify...
Thx
Hi @stich86,
I have already corrected the package and it should be OK.
As for changing the settings in the packages, before compiling, create a folder /files/etc/config and put the modified settings files for the packages there.
You can get the settings files by creating a backup archive. After extracting the archive you have a folder "etc" and from there you copy the files you are interested in.

Hi 4IceG,

I can confirm that now watchdog-lite is working.
Regarding /files/etc/config should be put into openwrt root folder where I run the make?

thx

2022-08-12 15:22:00

here is new build:

https://mega.nz/folder/u4whXLYJ#21cWTZELti69USXLIiAezQ

as usual you need to change ttyUSB0 to 1 on all 4IceG package and for "Connection Monitor" it's necessary to give executable permitiont to the binary file under /usr/bin with:

chmod +x lite_*
chmod +x lite-*

@4IceG do you know why the app for connection monitor doesn't give +x permission to file lite_watchdog*/lite-watchdog*?

Also.. how to force ttyUSB to USB1 on your package? So I can avoid each time to manually modify...

Thx

2022-08-11 11:50:55

MiG25 napisał/a:

Did you made some new builds with you can share ?

REMOVED - there is a problem with connection monitor from 4IceG and switch report is still wrong. I’ll try to build new one foe this evening and share it for test

new build with all fixed suggested by Leo-PL (let me know if the switch is correctly displayed now)
for AT1 version still need to change board-2.bin and add firmware-5.bin fro QCA9984

also all app from 4IceG was added

2022-08-10 19:14:44

MiG25 napisał/a:

Did you made some new builds with you can share ?

No yet

I’m fixing the issues reported by @Leo-PL on my PR.

When done I’ll share new one (with latest 4IceG package)

2022-08-10 19:11:37

MiG25 napisał/a:

@stich86 Dutch or German ? I belive you talking about VDFDE ?
Ciągle te z T-Mobila są zagadką .

Yes sorry…
The one sold by Vodafone DE (called GigaCube)

2022-08-10 19:04:31

Cezary napisał/a:

- price (? twice as mf286d)

Dutch version has higher price for b20 aggregation… but now with the unlock of b20 on Italian version price should decrease (I hope..)

2022-08-10 16:01:16

smereka napisał/a:

Na znanym portalu była jedna sztuka bodajże z vodefona za 580 i chyba ktoś po Twoim wpisie go chapnął Też chętnie bym go kupił ale 2 porty lan w przynajmniej w moich oczach go dyskwalifikują. Cena/jakośc chyba dalej mf286d przoduje. A czy w tym mf289f to switch jest normalny działają vlany? Czy jednak ten sam chłam co w mf286d?

There are three major changes on this router:

- from factor
- 5Ghz WiFi (QCA9984 MiMO 4x4 if you got AT1 rev)
- 4CA SDX24 modem (possibility of 5CA still under investigation)

Switch is the same of MF286D, you lose 2 ports

2022-08-09 10:52:26

MiG25 napisał/a:

@stich86 , what about switch ? It i only a case to correct it in config/network , o there is a configuration in DTS ? since now there are 4 LAN ports instead 2.

I’ve to take a look on it

2022-08-07 20:36:25

MiG25 napisał/a:

AT+CREG? gives all infos , when modem is in 3G mode ,so all infos are there , when 3G is on.

Yes but not in 4G

2022-08-07 19:26:29

MiG25 napisał/a:

Tak , identycznie jak w MF286D działa komenda AT+ZNLOCKBAND , i ma identyczną defaultową wartość ( choć @stich86 coś wspominał ,że z włoskiego Vodaphone defaultowo nie ma B20 , ale dało się to włączyć).
czyli np
AT+ZNLOCKBAND=1,0,45,0
ustawi B1+B3+B7

B20 is pruned from the combo on VFIT, but removing 4 files in the EFS partition unlock also the Italian variant

We are working to see if the modem can do 5CA

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Opcje wyszukiwania (Strona 7 z 16)

Znalezione posty: 151 do 175 z 393

151 Odpowiedź przez stich86 2022-08-18 10:05:21

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

152 Odpowiedź przez stich86 2022-08-17 16:59:05

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

153 Odpowiedź przez stich86 2022-08-17 16:52:10

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

154 Odpowiedź przez stich86 2022-08-17 15:49:17

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

155 Odpowiedź przez stich86 2022-08-17 15:12:32

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

156 Odpowiedź przez stich86 2022-08-17 12:17:31

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

157 Odpowiedź przez stich86 2022-08-17 12:15:32

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

158 Odpowiedź przez stich86 2022-08-17 11:52:30

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

159 Odpowiedź przez stich86 2022-08-17 09:57:32

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

160 Odpowiedź przez stich86 2022-08-16 21:00:24

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

161 Odpowiedź przez stich86 2022-08-16 14:59:58

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

162 Odpowiedź przez stich86 2022-08-16 14:03:47

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

163 Odpowiedź przez stich86 2022-08-16 13:45:45

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

164 Odpowiedź przez stich86 2022-08-16 10:25:46

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

165 Odpowiedź przez stich86 2022-08-15 21:45:17

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

166 Odpowiedź przez stich86 2022-08-13 15:10:01

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

167 Odpowiedź przez stich86 2022-08-12 15:22:00

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

168 Odpowiedź przez stich86 2022-08-11 11:50:55

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

169 Odpowiedź przez stich86 2022-08-10 19:14:44

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

170 Odpowiedź przez stich86 2022-08-10 19:11:37

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

171 Odpowiedź przez stich86 2022-08-10 19:04:31

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

172 Odpowiedź przez stich86 2022-08-10 16:01:16

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

173 Odpowiedź przez stich86 2022-08-09 10:52:26

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

174 Odpowiedź przez stich86 2022-08-07 20:36:25

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

175 Odpowiedź przez stich86 2022-08-07 19:26:29

Odp: ZTE MF289F - Porting OpenWRT (1,110 odpowiedzi, napisanych Sprzęt / Hardware)

Znalezione posty: 151 do 175 z 393