76 Odpowiedź przez slawekw

(23 odpowiedzi, napisanych Oprogramowanie / Software)

okdkad po rebucie zniknely urzadzenia /dev/ttyUSB*, w logread nie ma za wiele informacji dot. modemu:
tyle w sumie
Fri Nov 27 22:46:58 2015 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 27 22:46:58 2015 daemon.notice netifd: wan (1772): Control device not valid
Fri Nov 27 22:46:58 2015 daemon.notice netifd: wan (1782): Stopping network
Fri Nov 27 22:46:58 2015 daemon.notice netifd: wan (1782): Can't open device /dev/ttyUSB0.
Fri Nov 27 22:46:58 2015 daemon.notice netifd: wan (1782): Failed to disconnect
Fri Nov 27 22:46:58 2015 daemon.notice netifd: Interface 'wan' is now down

root@OpenWrt:~# logread
Fri Nov 27 22:46:47 2015 kern.warn kernel: [    0.490000] m25p80 spi0.0: found s25sl032p, expected m25p80
Fri Nov 27 22:46:47 2015 kern.info kernel: [    0.490000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.500000] 5 tp-link partitions found on MTD device spi0.0
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.500000] Creating 5 MTD partitions on "spi0.0":
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.510000] 0x000000000000-0x000000020000 : "u-boot"
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.510000] 0x000000020000-0x000000145c3c : "kernel"
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.520000] 0x000000145c3c-0x0000003f0000 : "rootfs"
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.520000] mtd: device 2 (rootfs) set to be root filesystem
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.530000] 1 squashfs-split partitions found on MTD device rootfs
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.530000] 0x000000390000-0x0000003f0000 : "rootfs_data"
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.540000] 0x0000003f0000-0x000000400000 : "art"
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    0.540000] 0x000000020000-0x0000003f0000 : "firmware"
Fri Nov 27 22:46:47 2015 kern.info kernel: [    0.580000] libphy: ag71xx_mdio: probed
Fri Nov 27 22:46:47 2015 kern.info kernel: [    1.180000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
Fri Nov 27 22:46:47 2015 kern.info kernel: [    1.190000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Fri Nov 27 22:46:47 2015 kern.info kernel: [    1.190000] TCP: cubic registered
Fri Nov 27 22:46:47 2015 kern.info kernel: [    1.190000] NET: Registered protocol family 17
Fri Nov 27 22:46:47 2015 kern.info kernel: [    1.200000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    1.210000] Bridge firewalling registered
Fri Nov 27 22:46:47 2015 kern.info kernel: [    1.220000] 8021q: 802.1Q VLAN Support v1.8
Fri Nov 27 22:46:47 2015 kern.err kernel: [    1.220000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Fri Nov 27 22:46:47 2015 kern.info kernel: [    1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Fri Nov 27 22:46:47 2015 kern.info kernel: [    1.240000] Freeing unused kernel memory: 240K (803a4000 - 803e0000)
Fri Nov 27 22:46:47 2015 user.info kernel: [    2.530000] init: Console is alive
Fri Nov 27 22:46:47 2015 user.info kernel: [    2.540000] init: - watchdog -
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.600000] usbcore: registered new interface driver usbfs
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.610000] usbcore: registered new interface driver hub
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.610000] usbcore: registered new device driver usb
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    4.670000] SCSI subsystem initialized
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.680000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.690000] ehci-platform: EHCI generic platform driver
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.690000] ehci-platform ehci-platform: EHCI Host Controller
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.700000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.710000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.730000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.730000] hub 1-0:1.0: USB hub found
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.730000] hub 1-0:1.0: 1 port detected
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.740000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.750000] ohci-platform: OHCI generic platform driver
Fri Nov 27 22:46:47 2015 kern.info kernel: [    4.760000] usbcore: registered new interface driver usb-storage
Fri Nov 27 22:46:47 2015 kern.info kernel: [    5.060000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Fri Nov 27 22:46:47 2015 kern.info kernel: [    5.250000] usb-storage 1-1:1.0: USB Mass Storage device detected
Fri Nov 27 22:46:47 2015 kern.info kernel: [    5.250000] scsi host0: usb-storage 1-1:1.0
Fri Nov 27 22:46:47 2015 user.info kernel: [    5.590000] init: - preinit -
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    6.270000] scsi 0:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    6.270000] random: procd urandom read with 10 bits of entropy available
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    6.280000] scsi 0:0:0:1: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    6.290000] sd 0:0:0:1: [sda] 15564800 512-byte logical blocks: (7.96 GB/7.42 GiB)
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    6.310000] sd 0:0:0:1: [sda] Write Protect is off
Fri Nov 27 22:46:47 2015 kern.debug kernel: [    6.310000] sd 0:0:0:1: [sda] Mode Sense: 0f 00 00 00
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    6.310000] sd 0:0:0:1: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Fri Nov 27 22:46:47 2015 kern.info kernel: [    6.340000]  sda: sda1 sda2
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    6.340000] sd 0:0:0:1: [sda] Attached SCSI removable disk
Fri Nov 27 22:46:47 2015 user.info kernel: [    8.660000] mount_root: loading kmods from internal overlay
Fri Nov 27 22:46:47 2015 kern.notice kernel: [    8.950000] jffs2: notice: (401) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Fri Nov 27 22:46:47 2015 user.info kernel: [    8.970000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
Fri Nov 27 22:46:47 2015 kern.info kernel: [    9.060000] EXT4-fs (sda2): recovery complete
Fri Nov 27 22:46:47 2015 kern.info kernel: [    9.070000] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts:
Fri Nov 27 22:46:47 2015 user.notice kernel: [    9.080000] mount_root: switched to extroot
Fri Nov 27 22:46:47 2015 user.info kernel: [    9.140000] procd: - early -
Fri Nov 27 22:46:47 2015 user.info kernel: [    9.140000] procd: - watchdog -
Fri Nov 27 22:46:47 2015 user.info kernel: [   10.040000] procd: - ubus -
Fri Nov 27 22:46:47 2015 user.info kernel: [   11.060000] procd: - init -
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.610000] usbcore: registered new interface driver huawei_ether
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.630000] usbcore: registered new interface driver cdc_wdm
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.630000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.640000] Backport generated by backports.git backports-20150129-0-gdd4a670
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.660000] nf_conntrack version 0.5.0 (445 buckets, 1780 max)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.690000] usbcore: registered new interface driver usbserial
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.700000] usbcore: registered new interface driver usbserial_generic
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.710000] usbserial: USB Serial support registered for generic
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.740000] xt_time: kernel timezone is -0000
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.750000] usbcore: registered new interface driver cdc_ncm
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.790000] cfg80211: Calling CRDA to update world regulatory domain
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.790000] cfg80211: World regulatory domain updated:
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.800000] cfg80211:  DFS Master region: unset
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.800000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.810000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.820000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.830000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.840000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.840000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.850000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.860000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.870000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.890000] usbcore: registered new interface driver huawei_cdc_ncm
Fri Nov 27 22:46:47 2015 kern.info kernel: [   13.900000] ip_tables: (C) 2000-2006 Netfilter Core Team
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.000000] PPP generic driver version 2.4.2
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.000000] NET: Registered protocol family 24
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.010000] usbcore: registered new interface driver qmi_wwan
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.020000] usbcore: registered new interface driver sierra
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.020000] usbserial: USB Serial support registered for Sierra USB modem
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.030000] usbcore: registered new interface driver sierra_net
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.080000] usbcore: registered new interface driver option
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.090000] usbserial: USB Serial support registered for GSM modem (1-port)
Fri Nov 27 22:46:47 2015 kern.debug kernel: [   14.120000] ath: EEPROM regdomain: 0x0
Fri Nov 27 22:46:47 2015 kern.debug kernel: [   14.120000] ath: EEPROM indicates default country code should be used
Fri Nov 27 22:46:47 2015 kern.debug kernel: [   14.120000] ath: doing EEPROM country->regdmn map search
Fri Nov 27 22:46:47 2015 kern.debug kernel: [   14.120000] ath: country maps to regdmn code: 0x3a
Fri Nov 27 22:46:47 2015 kern.debug kernel: [   14.120000] ath: Country alpha2 being used: US
Fri Nov 27 22:46:47 2015 kern.debug kernel: [   14.120000] ath: Regpair used: 0x3a
Fri Nov 27 22:46:47 2015 kern.debug kernel: [   14.130000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.140000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.140000] cfg80211: Calling CRDA for country: US
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.180000] cfg80211: Regulatory domain changed to country: US
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.180000] cfg80211:  DFS Master region: FCC
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.180000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.190000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.200000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.210000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.220000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.info kernel: [   14.230000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Fri Nov 27 22:46:47 2015 kern.notice kernel: [   15.060000] random: nonblocking pool is initialized
Fri Nov 27 22:46:49 2015 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly
Fri Nov 27 22:46:49 2015 daemon.err block: /dev/sda2 is already mounted
Fri Nov 27 22:46:50 2015 cron.info crond[1027]: crond (busybox 1.23.2) started, log level 5
Fri Nov 27 22:46:51 2015 authpriv.info dropbear[1049]: Not backgrounding
Fri Nov 27 22:46:52 2015 user.emerg syslog: setting up led USB
Fri Nov 27 22:46:52 2015 user.emerg syslog: setting up led WLAN
Fri Nov 27 22:46:52 2015 user.emerg syslog: setting up led LAN
Fri Nov 27 22:46:52 2015 daemon.info procd: - init complete -
Fri Nov 27 22:46:53 2015 daemon.warn netifd: You have delegated IPv6-prefixes but haven't assigned them to any interface. Did you forget to set option ip6assign on your lan-interfaces?
Fri Nov 27 22:46:53 2015 daemon.notice netifd: Interface 'loopback' is enabled
Fri Nov 27 22:46:53 2015 daemon.notice netifd: Interface 'loopback' is setting up now
Fri Nov 27 22:46:53 2015 daemon.notice netifd: Interface 'loopback' is now up
Fri Nov 27 22:46:53 2015 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 27 22:46:53 2015 daemon.notice netifd: Interface 'lan' is enabled
Fri Nov 27 22:46:53 2015 daemon.notice netifd: Interface 'lan' is setting up now
Fri Nov 27 22:46:53 2015 daemon.notice netifd: Interface 'lan' is now up
Fri Nov 27 22:46:54 2015 daemon.notice netifd: Network device 'lo' link is up
Fri Nov 27 22:46:54 2015 daemon.notice netifd: Interface 'loopback' has link connectivity
Fri Nov 27 22:46:54 2015 daemon.notice netifd: wan (1123): Control device not valid
Fri Nov 27 22:46:54 2015 daemon.notice netifd: wan (1151): Stopping network
Fri Nov 27 22:46:54 2015 daemon.notice netifd: wan (1151): Can't open device /dev/ttyUSB0.
Fri Nov 27 22:46:54 2015 daemon.notice netifd: wan (1151): Failed to disconnect
Fri Nov 27 22:46:55 2015 kern.info kernel: [   24.240000] cfg80211: Calling CRDA for country: PL
Fri Nov 27 22:46:55 2015 kern.info kernel: [   24.240000] cfg80211: Regulatory domain changed to country: PL
Fri Nov 27 22:46:55 2015 kern.info kernel: [   24.250000] cfg80211:  DFS Master region: ETSI
Fri Nov 27 22:46:55 2015 kern.info kernel: [   24.250000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Fri Nov 27 22:46:55 2015 kern.info kernel: [   24.260000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Fri Nov 27 22:46:55 2015 kern.info kernel: [   24.270000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
Fri Nov 27 22:46:55 2015 kern.info kernel: [   24.280000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
Fri Nov 27 22:46:55 2015 kern.info kernel: [   24.290000] cfg80211:   (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
Fri Nov 27 22:46:55 2015 kern.info kernel: [   24.300000] cfg80211:   (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Fri Nov 27 22:46:55 2015 daemon.notice netifd: Interface 'wan' is now down
Fri Nov 27 22:46:56 2015 daemon.notice netifd: radio0 (1126): Configuration file: /var/run/hostapd-phy0.conf
Fri Nov 27 22:46:56 2015 kern.info kernel: [   26.040000] device wlan0 entered promiscuous mode
root@OpenWrt:~# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fd9c:cef1:c801::/48'
network.lan=interface
network.lan.ifname='wlan0'
network.lan.type='bridge'
network.lan.proto='static'
network.lan.ipaddr='192.168.222.193'
network.lan.netmask='255.255.255.192'
network.wan=interface
network.wan.ifname='wwan0'
network.wan.device='/dev/ttyUSB0'
network.wan.apn='data.lycamobile.pl'
network.wan.proto='ncm'
network.wan.username='lmpl'
network.wan.password='lmpl'
root@OpenWrt:~# ifstatus wan
{
        "up": false,
        "pending": false,
        "available": false,
        "autostart": true,
        "proto": "ncm",
        "data": {

        },
        "errors": [
                {
                        "subsystem": "ncm",
                        "code": "DISCONNECT_FAILED"
                }
        ]
}

Czy zniknięcie urządzeń /dev/ttyUSB* mogło być spowodowane konfliktem/nadmiarowością doinstalowanych pakietów?

Idź do forum: Oprogramowanie / Software

77 Odpowiedź przez slawekw

(23 odpowiedzi, napisanych Oprogramowanie / Software)

witam,
wrzucilem obraz CC z eko.onet.pl, ale dalej nie dostaje IP na wan interfejsie.

 ----------------------------------------------------------------
 |                                                              |
 | OpenWrt Chaos Calmer 15.05 (r47662)                          |
 | Build time: 2015-11-27 20:34 CET                             |
 |                                                              |
 | Cezary Jackiewicz (obsy), http://eko.one.pl                  |
 |                                                              |
 ----------------------------------------------------------------
 | Machine: TP-Link TL-MR3020 v1                                |
 | Uptime: 0d, 00:13:55                                         |
 | Load: 0.08 0.03 0.05                                         |
 | Flash: total: 6.7GB, free: 6.3GB, used: 0%                   |
 | Memory: total: 27.8MB, free: 15.7MB, used: 43%               |
 | WAN:                                                         |
 | LAN: 192.168.222.193                                         |

root@OpenWrt:~# df
Filesystem           1K-blocks      Used Available Use% Mounted on
rootfs                 7011928     22000   6610692   0% /
/dev/root                 2304      2304         0 100% /rom
tmpfs                    14248        72     14176   1% /tmp
/dev/sda2              7011928     22000   6610692   0% /overlay
overlayfs:/overlay     7011928     22000   6610692   0% /
tmpfs                      512         0       512   0% /dev
root@OpenWrt:~#

obecnie mam extroot na karcie microsd ktora siedzi w modemie. czy to moze byc problem?

zauwazylem tez, ze po rebucie zniknely urzadzenia /dev/ttyUSB* - przed rebutem 3ginfo pokazywał:

root@OpenWrt:/etc/config# 3ginfo
Status: Brak informacji
Czas polaczenia: -
Przeslano danych: - / -
Operator: Plus
Tryb pracy: WCDMA
Sila sygnalu: 61%
Urzadzenie: huawei E3372
MCC MNC: 260 01
LAC: A029 (41001)
LCID: 0064C58B (6604171)
RNC: 0064 (100)
eNB: - (-)
CID: C58B (50571)
CSQ: 19
RSSI: -75 dBm
RSCP: -76 dBm
Ec/IO: -7 dB
RSRP: - dBm
RSRQ: - dB

a po rebucie jest błąd bo urządzenia zniknęły:

root@OpenWrt:/etc/config# 3ginfo
Brak urządzenia /dev/ttyUSB1.

Czy mógłby ktoś jednoznacznie powiedzieć które pakiety dla 'pure' modemu e3372h bez HiLinka, powinienem mieć zainstalowane a które nie? Obecnie mam takie:

root@OpenWrt:~# opkg list
3ginfo-text - 20151025
base-files - 157-r47662
block-mount - 2015-09-15-cc63723d886fde2cd364a545b7cb05b70721b83f
busybox - 1.23.2-1
chat - 2.4.7-6
comgt - 0.32-25
comgt-directip - 0.32-25
comgt-ncm - 0.32-25
dnsmasq - 2.73-1
dropbear - 2015.67-1
e2fsprogs - 1.42.12-1
firewall - 2015-07-27
fstools - 2015-09-15-cc63723d886fde2cd364a545b7cb05b70721b83f
hostapd-common - 2015-03-25-1
iptables - 1.4.21-1
iw - 3.17-1
iwinfo - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371
jshn - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb
jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9
kernel - 3.18.23-1-d58e1a55298dee9b8512e308c5b900ff
kmod-ath - 3.18.23+2015-03-09-3
kmod-ath9k - 3.18.23+2015-03-09-3
kmod-ath9k-common - 3.18.23+2015-03-09-3
kmod-cfg80211 - 3.18.23+2015-03-09-3
kmod-crypto-aes - 3.18.23-1
kmod-crypto-arc4 - 3.18.23-1
kmod-crypto-core - 3.18.23-1
kmod-crypto-hash - 3.18.23-1
kmod-fs-ext4 - 3.18.23-1
kmod-fs-vfat - 3.18.23-1
kmod-gpio-button-hotplug - 3.18.23-1
kmod-huawei-hw-cdc - 3.18.23+2.07.00.00-1
kmod-ipt-conntrack - 3.18.23-1
kmod-ipt-core - 3.18.23-1
kmod-ipt-nat - 3.18.23-1
kmod-ledtrig-usbdev - 3.18.23-1
kmod-lib-crc-ccitt - 3.18.23-1
kmod-lib-crc16 - 3.18.23-1
kmod-mac80211 - 3.18.23+2015-03-09-3
kmod-mii - 3.18.23-1
kmod-nf-conntrack - 3.18.23-1
kmod-nf-ipt - 3.18.23-1
kmod-nf-nat - 3.18.23-1
kmod-nf-nathelper - 3.18.23-1
kmod-nls-base - 3.18.23-1
kmod-nls-cp437 - 3.18.23-1
kmod-nls-iso8859-1 - 3.18.23-1
kmod-ppp - 3.18.23-1
kmod-pppoe - 3.18.23-1
kmod-pppox - 3.18.23-1
kmod-scsi-core - 3.18.23-1
kmod-slhc - 3.18.23-1
kmod-usb-core - 3.18.23-1
kmod-usb-net - 3.18.23-1
kmod-usb-net-cdc-ncm - 3.18.23-1
kmod-usb-net-huawei-cdc-ncm - 3.18.23-1
kmod-usb-net-qmi-wwan - 3.18.23-1
kmod-usb-net-sierrawireless - 3.18.23-1
kmod-usb-ohci - 3.18.23-1
kmod-usb-serial - 3.18.23-1
kmod-usb-serial-option - 3.18.23-1
kmod-usb-serial-sierrawireless - 3.18.23-1
kmod-usb-serial-wwan - 3.18.23-1
kmod-usb-storage - 3.18.23-1
kmod-usb-wdm - 3.18.23-1
kmod-usb2 - 3.18.23-1
libblobmsg-json - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb
libc - 0.9.33.2-1
libext2fs - 1.42.12-1
libgcc - 4.8-linaro-1
libip4tc - 1.4.21-1
libip6tc - 1.4.21-1
libiwinfo - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371
libjson-c - 0.12-1
libjson-script - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb
libnl-tiny - 0.1-4
libubox - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb
libubus - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
libuci - 2015-08-27.1-1
libusb-1.0 - 1.0.19-1
libuuid - 2.25.2-4
libxtables - 1.4.21-1
mtd - 21
netifd - 2015-09-27-509ffb22475ebdd5291d510a098f996473951344
opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-9
ppp - 2.4.7-6
ppp-mod-pppoe - 2.4.7-6
procd - 2015-10-29-d5fddd91b966424bb63e943e789704d52382cc18
swconfig - 10
ubox - 2015-11-22-c086167a0154745c677f8730a336ea9cf7d71031
ubus - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
ubusd - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
uci - 2015-08-27.1-1
usb-modeswitch - 2014-08-26-993a9a542791953c4804f7ddbb3a07756738e37a
usign - 2015-05-08-cf8dcdb8a4e874c77f3e9a8e9b643e8c17b19131
wpad-mini - 2015-03-25-1
wwan - 2014-07-17-1
root@OpenWrt:~#

Idź do forum: Oprogramowanie / Software

78 Odpowiedź przez slawekw

(23 odpowiedzi, napisanych Oprogramowanie / Software)

witam,
sprawdze wieczorem konfiguracje "network" z /dev/ttyUSB0
rozumiem ze /etc/config/3ginfo ma mieć jak obecnie /dev/cdc-wdm0

Tutaj tez ktos pisal ze pod CC dziala mu model h, ale z jakimis hakami
https://lists.openwrt.org/pipermail/ope … 33997.html

czy modes auto znaczy ze zezwala na roaming danych w sieci Plus? Lycamobile działa tylko na nadajnikach Plusa, i normalnie roaming musi być włączony w telefonie z kartą lycamobile.

Co do extroota to sie nad tym zastanawialem, ale poniewaz ten ruter ma tylko port USB nie wiem czy to by działało z hubem USB. Bo rozumiem, ze karta microsd w modemie nie bedzie dzialała pod extroot'a.

pozdrawiam,

Idź do forum: Oprogramowanie / Software

79 Odpowiedź przez slawekw

(23 odpowiedzi, napisanych Oprogramowanie / Software)

witam, mam juz jaki postęp / wszystkie pakiety sa na miejscu, 3ginfo pokazuje status:

# 3ginfo
Status: Połączony
Czas polaczenia: 0d, 00:04:57
Przeslano danych: 0.0 B / 818.0 B
Operator: Plus
Tryb pracy: WCDMA
Sila sygnalu: 54%
Urzadzenie: huawei E3372
MCC MNC: 260 01
LAC: A029 (41001)
LCID: 0064C58E (6604174)
RNC: 0064 (100)
eNB: - (-)
CID: C58E (50574)
CSQ: 17
RSSI: -79 dBm
RSCP: -78 dBm
Ec/IO: -6 dB
RSRP: - dBm
RSRQ: - dB

Jednak na wwan0 nie dostaje IP od dostawcy / sieci (nie pokaga ifdown/ifup wan czu reboot)

wwan0     Link encap:Ethernet  HWaddr 00:1D:11:2F:00:00
          inet6 addr: fe80::21e:10ff:fe1f:0/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:818 (818.0 B)

konfiguracja sieci wan taka:

config interface wan
        option ifname 'wwan0'
        option device  /dev/cdc-wdm0
        option apn     data.lycamobile.pl
        option proto   ncm
        option username lmpl
        option password lmpl

z góry dziękują za jakąś wskazówkę,
pozdrawiam
Sławek

Idź do forum: Oprogramowanie / Software

80 Temat przez slawekw

(23 odpowiedzi, napisanych Oprogramowanie / Software)

Witam,
modem został przełączony z HiLink do stick modem mode zgodnie z instrukcja http://blog.asiantuntijakaveri.fi/2015/ … -from.html

czy bedzie on dziala w openwrt CC? co nalezy doinstalowac?
tutaj na eko.one.pl znalazlem instrukcje dla modemów z HiLinkiem, a co mozna zrobic aby dzialal w moim przypadku?

Na eko.onet.pl znalazlem informacje o takim pakiecie do innych Huawei:
Huawei E3272, E3276 - kmod-usb-net-ncm

Czy do E3372 tez powinienem go zainstalowac? Gdzie mogę znaleźć wersję dla Openwrt CC?

pozdrawiam
Slawek

Idź do forum: Oprogramowanie / Software

81 Temat przez slawekw

(1 odpowiedzi, napisanych Oprogramowanie / Software)

witam,
ja można skonfigurować np. dwa skrajne przełączniki w tym modemie: AP i 3G, aby po przełączeniu na dowolny z nich uruchamiał się skrypt /etc/rc.button/power który zawiera:

:/etc/rc.button# cat power
#!/bin/sh

[ "${ACTION}" = "released" ] || exit 0

exec /sbin/poweroff

return 0

Idź do forum: Oprogramowanie / Software

82 Odpowiedź przez slawekw

(5 odpowiedzi, napisanych Oprogramowanie / Software)

znalazlem taka radę - i działa wyłączanie wifi ale nie jestem pewien jak dodac do tego wyłączanie 3g:

skopiowalem /etc/rc.button/rfkill pod /etc/rc.button/wps

i juz dziala wyłączanie wifi.

Ale po dodaniu komend programowego wyłączania zasilania na usb do skryptu wps) nie mam pewnosci czy to jest poprawnie i bedzie dzialac:

:/etc/rc.button# cat wps
#!/bin/sh

[ "${ACTION}" = "released" -o -n "${TYPE}" ] || exit 0

. /lib/functions.sh

local rfkill_state=0

wifi_rfkill_set() {
        uci set wireless.$1.disabled=$rfkill_state
        echo 0 > /sys/class/gpio/gpio8/value
}

wifi_rfkill_check() {
        local disabled
        config_get disabled $1 disabled
        [ "$disabled" = "1" ] || rfkill_state=1
}

config_load wireless
case "${TYPE}" in
"switch")
        [ "${ACTION}" = "released" ] && rfkill_state=1
        ;;
*)
        config_foreach wifi_rfkill_check wifi-device
        ;;
esac
config_foreach wifi_rfkill_set wifi-device
uci commit wireless
wifi up
echo 1 > /sys/class/gpio/gpio8/value

return 0

Idź do forum: Oprogramowanie / Software

83 Odpowiedź przez slawekw

(5 odpowiedzi, napisanych Oprogramowanie / Software)

witam,
dziekuje za odpowiedź. tak, karta działała - wziąłem ją z telefonu gdzie działała, niestety w modemie nie działała.
Co sie okazało, modem ten nie obslugiwał tej konkretnie karty Lycamobile tzn. jakby za nowa technologia (???) To była karta ktora mogla byc mini/micro/nano simm'em - tzn. mozna byl tak "wyłamać". Ja potrzebowałem mini wiec nie wyłamywałem nic, ale nie dzialala w modemie - problem jak opisalem.
Wystarczylo, ze kupilem karte tylko Mini (bez mozliwosci wylamania) i od razu po wymianie zaczela dzialac z ta konfiguracja ktora wczesniej zrobilem w openwrt.

Mam jeszcze takie dwa pyt. dot. tego rutera i lycamobile:

1) jak moglbym skonfigurowac przycisk (jedyny w MR3020) aby po jego nacisnieciu rozlaczalo sie wifi i polaczenie 3g? takie wlaczenie a'la trybu samolotowego jak w komorce i aby ponowne wcisniecie przycisku włączało wifi/3g z powrotem.

2) czy mozna jakąś prostą komendą z shell'a openwrt sprawdzć stan pakietu (megabajtow) w pakiecie lycamobile i jego ważność?

jeszcze raz dzieki za pomoc.
pozdrawiam
Sławek

Idź do forum: Oprogramowanie / Software

84 Temat przez slawekw

(5 odpowiedzi, napisanych Oprogramowanie / Software)

witam, modem Huawei E160g sie łączy i za chwile jest Modem hangup i tak w kółko

/etc/config/network napisał/a:

config interface wan
        option ifname 'ppp0'
        option device  /dev/ttyUSB0
        option apn     data.lycamobile.pl
        option service umts
        option proto   3g
        option username lmpl
        option password lmpl
        #option 'pppd_options' 'debug noipdefault'

logread napisał/a:

Wed Nov 18 20:06:42 2015 daemon.info pppd[1724]: Exit.
Wed Nov 18 20:06:42 2015 daemon.notice netifd: Interface 'wan' is now down
Wed Nov 18 20:06:42 2015 daemon.notice netifd: Interface 'wan' is setting up now
Wed Nov 18 20:06:44 2015 daemon.notice netifd: wan (1768): Trying to set mode
Wed Nov 18 20:06:45 2015 daemon.notice pppd[1783]: pppd 2.4.7 started by root, uid 0
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: abort on (BUSY)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: abort on (NO CARRIER)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: abort on (ERROR)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: report (CONNECT)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: timeout set to 10 seconds
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: send (AT&F^M)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: expect (OK)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: AT&F^M^M
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: OK
Wed Nov 18 20:06:46 2015 local2.info chat[1785]:  -- got it
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: send (ATE1^M)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: expect (OK)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: ^M
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: ATE1^M^M
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: OK
Wed Nov 18 20:06:46 2015 local2.info chat[1785]:  -- got it
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: send (AT+CGDCONT=1,"IP","data.lycamobile.pl"^M)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: timeout set to 30 seconds
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: expect (OK)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: ^M
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: AT+CGDCONT=1,"IP","data.lycamobile.pl"^M^M
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: OK
Wed Nov 18 20:06:46 2015 local2.info chat[1785]:  -- got it
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: send (ATD*99***1#^M)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: expect (CONNECT)
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: ^M
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: ATD*99***1#^M^M
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: CONNECT
Wed Nov 18 20:06:46 2015 local2.info chat[1785]:  -- got it
Wed Nov 18 20:06:46 2015 local2.info chat[1785]: send ( ^M)
Wed Nov 18 20:06:46 2015 daemon.debug pppd[1783]: Script USE_APN=data.lycamobile.pl DIALNUMBER=*99***1# /usr/sbin/chat -t5 -v -E -f /etc/chatscripts/3g.chat finished (pid 1784), status = 0x0
Wed Nov 18 20:06:46 2015 daemon.info pppd[1783]: Serial connection established.
Wed Nov 18 20:06:46 2015 daemon.debug pppd[1783]: using channel 16
Wed Nov 18 20:06:46 2015 daemon.info pppd[1783]: Using interface 3g-wan
Wed Nov 18 20:06:46 2015 daemon.notice pppd[1783]: Connect: 3g-wan <--> /dev/ttyUSB0
Wed Nov 18 20:06:46 2015 kern.info kernel: [   95.390000] 3g-wan: renamed from ppp0
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0xc94bea95>]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: rcvd [LCP ConfReq id=0xf5 <asyncmap 0x0> <auth chap MD5> <magic 0x13bb7ca> <pcomp> <accomp>]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: sent [LCP ConfRej id=0xf5 <pcomp> <accomp>]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0xc94bea95>]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: rcvd [LCP ConfReq id=0xf6 <asyncmap 0x0> <auth chap MD5> <magic 0x13bb7ca>]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: sent [LCP ConfAck id=0xf6 <asyncmap 0x0> <auth chap MD5> <magic 0x13bb7ca>]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: sent [LCP EchoReq id=0x0 magic=0xc94bea95]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: rcvd [LCP DiscReq id=0xf7 magic=0x13bb7ca]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: rcvd [CHAP Challenge id=0x1 <xxxxxxxxxxxxxxxxxxxxxxxxx>, name = "UMTS_CHAP_SRVR"]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: sent [CHAP Response id=0x1 <xxxxxxxxxxxxxxxxxxxxxxxxxx>, name = "lmpl"]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: rcvd [LCP EchoRep id=0x0 magic=0x13bb7ca c9 4b ea 95]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: rcvd [CHAP Success id=0x1 ""]
Wed Nov 18 20:06:47 2015 daemon.info pppd[1783]: CHAP authentication succeeded
Wed Nov 18 20:06:47 2015 daemon.notice pppd[1783]: CHAP authentication succeeded
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
Wed Nov 18 20:06:47 2015 daemon.debug pppd[1783]: sent [IPV6CP ConfReq id=0x1 <addr fe80::a454:2b98:ad64:e410>]
Wed Nov 18 20:06:47 2015 daemon.notice pppd[1783]: Modem hangup
Wed Nov 18 20:06:47 2015 daemon.notice pppd[1783]: Connection terminated.
Wed Nov 18 20:06:48 2015 daemon.info pppd[1783]: Exit.
Wed Nov 18 20:06:49 2015 daemon.notice netifd: Interface 'wan' is now down
Wed Nov 18 20:06:49 2015 daemon.notice netifd: Interface 'wan' is setting up now
Wed Nov 18 20:06:51 2015 daemon.notice netifd: wan (1826): Trying to set mode
Wed Nov 18 20:06:51 2015 daemon.notice pppd[1841]: pppd 2.4.7 started by root, uid 0

zostawie go na 2h i tak w kolko bedzie sie laczyl i rozlaczal

Idź do forum: Oprogramowanie / Software