Są postępy, kiedy wydałem rozkaz z konsoli UART:
root@OpenWrt:/# sysupgrade -n -F /tmp/openwrt-19.07-snapshot-r11267-b14eeccdfe-
ramips-mt7620-zbt-we826-32M-squashfs-sysupgrade.bin
Sysupgrade is not yet supported on oolite-7620a.
Image check 'platform_check_image' failed but --force given - will update anyway !
killall: watchdog: no process killed
Sending TERM to remaining processes ... udhcpc ntpd dnsmasq ubusd logd netifd od hcpd uhttpd
Sending KILL to remaining processes ...
Switching to ramdisk...
Performing system upgrade...
Unlocking firmware ...
Writing from <stdin> to firmware ... [[w] ]
Upgrade completed
Rebooting s[ 232.690000] Restarting system.
Dmesg
[ 0.000000] Linux version 4.14.212 (cezary@eko.one.pl) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11261-3f5fecfd33)) #0 Thu Dec 17 14:51:43 2020
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is ZBT-WE826 (32M)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 80484730, node_mem_map 81000040
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] random: get_random_bytes called from 0x80487740 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=0004000f
[ 0.000000] Readback ErrCtl register=0004000f
[ 0.000000] Memory: 123780K/131072K available (3943K kernel code, 181K rwdata, 504K rodata, 1188K init, 215K bss, 7292K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015490] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.087736] pid_max: default: 32768 minimum: 301
[ 0.097139] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110165] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.130298] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.149780] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.161954] pinctrl core: initialized pinctrl subsystem
[ 0.173585] NET: Registered protocol family 16
[ 0.440750] mt7620-pci 10140000.pcie: PCIE0 no card, disable it(RST&CLK)
[ 0.453993] mt7620-pci: probe of 10140000.pcie failed with error -1
[ 0.484651] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.495692] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.508277] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.519277] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.531864] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.542691] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.560101] clocksource: Switched to clocksource systick
[ 0.571763] NET: Registered protocol family 2
[ 0.581307] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.595095] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.607686] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.620470] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.631994] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.644690] NET: Registered protocol family 1
[ 0.653274] PCI: CLS 0 bytes, default 32
[ 0.656112] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.668853] Crashlog allocated RAM at address 0x3f00000
[ 0.681027] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.699737] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.711248] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.741592] io scheduler noop registered
[ 0.749234] io scheduler deadline registered (default)
[ 0.760516] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.776004] console [ttyS0] disabled
[ 0.783068] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.802747] console [ttyS0] enabled
[ 0.809796] bootconsole [early0] disabled
[ 0.826230] spi spi0.0: force spi mode3
[ 0.841952] m25p80 spi0.0: w25q256 (32768 Kbytes)
[ 0.846807] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.853323] Creating 4 MTD partitions on "spi0.0":
[ 0.858222] 0x000000000000-0x000000030000 : "u-boot"
[ 0.864251] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.870608] 0x000000040000-0x000000050000 : "factory"
[ 0.876620] 0x000000050000-0x000002000000 : "firmware"
[ 0.885789] 2 uimage-fw partitions found on MTD device firmware
[ 0.891912] Creating 2 MTD partitions on "firmware":
[ 0.896992] 0x000000000000-0x000000180a08 : "kernel"
[ 0.902972] 0x000000180a08-0x000001fb0000 : "rootfs"
[ 0.908843] mtd: device 5 (rootfs) set to be root filesystem
[ 0.916303] 1 squashfs-split partitions found on MTD device rootfs
[ 0.922701] 0x000000460000-0x000001fb0000 : "rootfs_data"
[ 0.929935] libphy: Fixed MDIO Bus: probed
[ 0.943229] gsw: setting port4 to ephy mode
[ 0.947551] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 2 link up (100Mbps/Full duplex)
[ 0.957144] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.963940] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 0.973104] rt2880_wdt 10000120.watchdog: Initialized
[ 0.979608] NET: Registered protocol family 10
[ 0.988737] Segment Routing with IPv6
[ 0.992672] NET: Registered protocol family 17
[ 0.997266] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 1.010523] 8021q: 802.1Q VLAN Support v1.8
[ 1.016391] hctosys: unable to open rtc device (rtc0)
[ 1.033012] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 1.046817] Freeing unused kernel memory: 1188K
[ 1.051492] This architecture does not have kernel memory protection.
[ 2.640057] random: fast init done
[ 2.809057] init: Console is alive
[ 2.812887] init: - watchdog -
[ 6.005486] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.309755] usbcore: registered new interface driver usbfs
[ 6.315542] usbcore: registered new interface driver hub
[ 6.321123] usbcore: registered new device driver usb
[ 6.358542] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.373684] SCSI subsystem initialized
[ 6.383093] ehci-platform: EHCI generic platform driver
[ 6.398818] phy phy-usbphy.0: remote usb device wakeup disabled
[ 6.404896] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 6.409448] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 6.415415] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 6.423644] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 6.437032] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 6.444463] hub 1-0:1.0: USB hub found
[ 6.448796] hub 1-0:1.0: 1 port detected
[ 6.456190] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.464194] ohci-platform: OHCI generic platform driver
[ 6.469898] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 6.476860] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 6.485112] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 6.518908] hub 2-0:1.0: USB hub found
[ 6.523188] hub 2-0:1.0: 1 port detected
[ 6.567115] usbcore: registered new interface driver usb-storage
[ 6.582856] usbcore: registered new interface driver uas
[ 6.588975] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.597984] init: - preinit -
[ 6.739145] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.868742] mmc0: new high speed SDHC card at address aaaa
[ 6.879907] mmcblk0: mmc0:aaaa SC16G 14.8 GiB
[ 6.894167] mmcblk0: p1
[ 6.955748] random: procd: uninitialized urandom read (4 bytes read)
[ 6.962826] hub 1-1:1.0: USB hub found
[ 6.968162] hub 1-1:1.0: 4 ports detected
[ 8.463140] 8021q: adding VLAN 0 to HW filter on device eth0
[ 9.784835] mount_root: loading kmods from internal overlay
[ 9.829808] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 9.838598] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 12.699561] block: attempting to load /etc/config/fstab
[ 12.705339] block: unable to load configuration (fstab: Entry not found)
[ 12.712359] block: no usable configuration
[ 12.717590] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 12.763243] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 12.874174] procd: - early -
[ 12.877245] procd: - watchdog -
[ 13.588707] procd: - watchdog -
[ 13.592286] procd: - ubus -
[ 13.892071] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.992775] random: ubusd: uninitialized urandom read (4 bytes read)
[ 13.999917] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.007561] procd: - init -
[ 15.000513] kmodloader: loading kernel modules from /etc/modules.d/*
[ 15.054368] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 15.083537] Loading modules backported from Linux version v4.19.161-0-gdaefdc9eb24b
[ 15.091445] Backport generated by backports.git v4.19.161-1-0-g4bb568fe
[ 15.128968] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.155614] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 15.308856] xt_time: kernel timezone is -0000
[ 15.563713] PPP generic driver version 2.4.2
[ 15.579194] urngd: jent-rng init failed, err: 2
[ 15.585897] NET: Registered protocol family 24
[ 15.629094] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 15.636577] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 15.644495] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 15.652277] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.676061] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 52.789370] 8021q: adding VLAN 0 to HW filter on device eth0
[ 52.820101] br-lan: port 1(eth0.1) entered blocking state
[ 52.825628] br-lan: port 1(eth0.1) entered disabled state
[ 52.831594] device eth0.1 entered promiscuous mode
[ 52.836491] device eth0 entered promiscuous mode
[ 52.899852] br-lan: port 1(eth0.1) entered blocking state
[ 52.905380] br-lan: port 1(eth0.1) entered forwarding state
[ 55.404990] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 55.420684] jffs2_build_filesystem(): unlocking the mtd device...
[ 55.420846] done.
[ 55.429192] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 99.728967] random: crng init done
[ 99.740082] random: 6 urandom warning(s) missed due to ratelimiting
Problemy: odrzuca połączenie przez stronkę - nie mogę się zalogować do LuCi. Może powinienem kliknąć jakiś reset ustawień z konsoli.
