RomBOOT


U-Boot 1.3.4 (Jan 28 2010 - 11:36:04)

DRAM:  64 MB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   macb0
macb0: Starting autonegotiation...
macb0: Autonegotiation complete
macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1)
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0xa0000, size 0x400000
 4194304 bytes read: OK
## Booting kernel from Legacy Image at 22000000 ...
   Image Name:   linux-2.6
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3385664 Bytes =  3.2 MB
   Load Address: 20008000
   Entry Point:  20008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

[    0.000000] Linux version 2.6.30 (lukasz@hp) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Thu Aug 29 12:23:24 CEST 2013
[    0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Atmel AT91SAM9G20-EK
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Clocks: CPU 396 MHz, master 132 MHz, main 18.432 MHz
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=5 root=ubi0:rootfs mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1)ro,128k(env2)ro,4M(linux),-(root) rw rootfstype=ubifs
[    0.000000] NR_IRQS:192
[    0.000000] AT91: 96 gpio irqs in 3 banks
[    0.000000] PID hash table entries: 256 (order: 8, 1024 bytes)
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttyS0] enabled
[    0.080000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.090000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.100000] Memory: 64MB = 64MB total
[    0.110000] Memory: 61432KB available (3060K code, 241K data, 124K init, 0K highmem)
[    0.110000] Calibrating delay loop... 197.83 BogoMIPS (lpj=989184)
[    0.330000] Mount-cache hash table entries: 512
[    0.330000] CPU: Testing write buffer coherency: ok
[    0.340000] net_namespace: 296 bytes
[    0.350000] NET: Registered protocol family 16
[    0.360000] AT91: Power Management
[    0.360000] AT91: Starting after user reset
[    0.390000] bio: create slab <bio-0> at 0
[    0.400000] SCSI subsystem initialized
[    0.400000] usbcore: registered new interface driver usbfs
[    0.410000] usbcore: registered new interface driver hub
[    0.420000] usbcore: registered new device driver usb
[    0.430000] NET: Registered protocol family 2
[    0.430000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.440000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.450000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.450000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.460000] TCP reno registered
[    0.460000] NET: Registered protocol family 1
[    0.470000] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.480000] JFFS2 version 2.2. (NAND) (SUMMARY)  Š 2001-2006 Red Hat, Inc.
[    0.490000] JFFS2: default compression mode: priority
[    0.490000] msgmni has been set to 120
[    0.500000] io scheduler noop registered
[    0.500000] io scheduler anticipatory registered (default)
[    0.550000] atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
[    0.560000] atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL
[    0.570000] atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL
[    0.570000] atmel_usart.3: ttyS3 at MMIO 0xfffb8000 (irq = 8) is a ATMEL_SERIAL
[    0.580000] atmel_usart.4: ttyS4 at MMIO 0xfffd0000 (irq = 23) is a ATMEL_SERIAL
[    0.590000] atmel_usart.5: ttyS5 at MMIO 0xfffd4000 (irq = 24) is a ATMEL_SERIAL
[    0.600000] atmel_usart.6: ttyS6 at MMIO 0xfffd8000 (irq = 25) is a ATMEL_SERIAL
[    0.620000] brd: module loaded
[    0.630000] loop: module loaded
[    0.640000] ssc ssc.0: Atmel SSC device at 0xc4898000 (irq 14)
[    0.640000] Driver 'sd' needs updating - please use bus_type methods
[    0.650000] scsi0 : pata_at91
[    0.650000] ata1: PATA max PIO4 mmio cmd 0x50c00000 ctl 0x50e00000 irq 88
[    0.660000] dm9000 Ethernet Driver, V1.31
[    0.670000] dm9000 dm9000.0: eth%d: Invalid ethernet MAC address. Please set using ifconfig
[    0.670000] eth0 (dm9000): not using net_device_ops yet
[    0.680000] eth0: dm9000e at c4876000,c487e004 IRQ 89 MAC: 00:00:00:00:00:00 (chip)
[    0.690000] MACB_mii_bus: probed
[    0.700000] eth1: Atmel MACB at 0xfffc4000 irq 21 (00:04:9f:ef:01:01)
[    0.700000] eth1: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:00, irq=-1)
[    0.720000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
[    0.730000] AT91 NAND: 8-bit, Software ECC
[    0.730000] Scanning device for bad blocks
[    0.770000] 6 cmdlinepart partitions found on MTD device atmel_nand
[    0.770000] Creating 6 MTD partitions on "atmel_nand":
[    0.780000] 0x000000000000-0x000000020000 : "bootstrap"
[    0.780000] 0x000000020000-0x000000060000 : "uboot"
[    0.790000] 0x000000060000-0x000000080000 : "env1"
[    0.800000] 0x000000080000-0x0000000a0000 : "env2"
[    0.800000] 0x0000000a0000-0x0000004a0000 : "linux"
[    0.810000] 0x0000004a0000-0x000008000000 : "root"
[    0.820000] UBI: attaching mtd5 to ubi0
[    0.820000] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[    0.830000] UBI: logical eraseblock size:    129024 bytes
[    0.830000] UBI: smallest flash I/O unit:    2048
[    0.840000] UBI: sub-page size:              512
[    0.840000] UBI: VID header offset:          512 (aligned 512)
[    0.850000] UBI: data offset:                2048
[    1.000000] UBI: attached mtd5 to ubi0
[    1.000000] UBI: MTD device name:            "root"
[    1.010000] UBI: MTD device size:            123 MiB
[    1.010000] UBI: number of good PEBs:        987
[    1.020000] UBI: number of bad PEBs:         0
[    1.020000] UBI: max. allowed volumes:       128
[    1.020000] UBI: wear-leveling threshold:    4096
[    1.030000] UBI: number of internal volumes: 1
[    1.030000] UBI: number of user volumes:     1
[    1.040000] UBI: available PEBs:             0
[    1.040000] UBI: total number of reserved PEBs: 987
[    1.050000] UBI: number of PEBs reserved for bad PEB handling: 9
[    1.050000] UBI: max/mean erase counter: 1/0
[    1.060000] UBI: background thread "ubi_bgt0d" started, PID 362
[    1.060000] usbmon: debugfs is not available
[    1.070000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.080000] at91_ohci at91_ohci: AT91 OHCI
[    1.080000] at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
[    1.090000] at91_ohci at91_ohci: irq 20, io mem 0x00500000
[    1.150000] usb usb1: configuration #1 chosen from 1 choice
[    1.160000] hub 1-0:1.0: USB hub found
[    1.160000] hub 1-0:1.0: 2 ports detected
[    1.170000] Initializing USB Mass Storage driver...
[    1.170000] usbcore: registered new interface driver usb-storage
[    1.180000] USB Mass Storage support registered.
[    1.180000] udc: at91_udc version 3 May 2006
[    1.190000] mice: PS/2 mouse device common for all mice
[    1.190000] rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0
[    1.200000] IRQ 1/rtc0: IRQF_DISABLED is not guaranteed on shared IRQs
[    1.210000] rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!
[    1.210000] i2c /dev entries driver
[    1.220000] at24 0-0050: 256 byte 24c02 EEPROM (writable)
[    1.220000] i2c-gpio i2c-gpio: using pins 55 (SDA) and 56 (SCL)
[    1.230000] Registered led device: ds1
[    1.240000] usbcore: registered new interface driver usbhid
[    1.250000] usbhid: v2.6:USB HID core driver
[    1.250000] TCP cubic registered
[    1.260000] NET: Registered protocol family 17
[    1.260000] RPC: Registered udp transport module.
[    1.270000] RPC: Registered tcp transport module.
[    1.280000] rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock
[    1.320000] UBIFS: recovery needed
[    1.360000] UBIFS: recovery completed
[    1.360000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.370000] UBIFS: file system size:   124250112 bytes (121338 KiB, 118 MiB, 963 LEBs)
[    1.370000] UBIFS: journal size:       9033728 bytes (8822 KiB, 8 MiB, 71 LEBs)
[    1.380000] UBIFS: media format:       w4/r0 (latest is w4/r0)
[    1.390000] UBIFS: default compressor: lzo
[    1.390000] UBIFS: reserved for root:  0 bytes (0 KiB)
[    1.400000] VFS: Mounted root (ubifs filesystem) on device 253:1.
[    1.400000] Freeing init memory: 124K
[    1.410000] Warning: unable to open an initial console.
[    1.430000] Kernel panic - not syncing: Attempted to kill init!
[    1.430000] Backtrace:
[    1.430000] [<c002b35c>] (dump_backtrace+0x0/0x110) from [<c027322c>] (dump_stack+0x18/0x1c)
[    1.440000]  r6:c3812c40 r5:0000000b r4:c0342c34
[    1.450000] [<c0273214>] (dump_stack+0x0/0x1c) from [<c027338c>] (panic+0x48/0x10c)
[    1.450000] [<c0273344>] (panic+0x0/0x10c) from [<c003e398>] (do_exit+0x68/0x5c0)
[    1.460000]  r3:c032bb1c r2:00000019 r1:00002710 r0:c02d8582
[    1.470000]  r7:c3818e40
[    1.470000] [<c003e330>] (do_exit+0x0/0x5c0) from [<c003ebec>] (do_group_exit+0x94/0xc8)
[    1.480000]  r7:c3818e40
[    1.480000] [<c003eb58>] (do_group_exit+0x0/0xc8) from [<c00474d0>] (get_signal_to_deliver+0x300/0x338)
[    1.490000]  r4:00106001
[    1.490000] [<c00471d0>] (get_signal_to_deliver+0x0/0x338) from [<c0029eb0>] (do_signal.part.0+0x68/0x4c8)
[    1.500000] [<c0029e48>] (do_signal.part.0+0x0/0x4c8) from [<c002a78c>] (do_notify_resume+0x40/0x44)
[    1.510000] [<c002a74c>] (do_notify_resume+0x0/0x44) from [<c0027c4c>] (work_pending+0x1c/0x20)