FAQ o OpenWrt | Sprzedam różne routery | Oddam

2013-06-19 11:30:48

Witam

teraz chce zeby pod overlay podmontowal dysk o uuid=b7248e21-d71a-41a9-b9f6-acc384dc8673 [sda1], i ten jest tez wpisany do /etc/config/fstab (flash). a pomimo tego po kazdym restarcie pod overlay'a montuje dysk o uuid=0c211d73-1eca-4520-b596-9c630cc4bf03 [sdb1] (na ktorym obecnie dziala extroot) i zabardzo niewiem dlaczego on w ogole ten dysk (0c211d73-1eca-4520-b596-9c630cc4bf03) chce tam montowac. ponizej raz jeszcze fragment /etc/config/fstab oraz wynik polecenia mount

config mount
        option target '/overlay'
        option device '/dev/sda98'
        option options 'rw,noatime'
        option enabled_fsck '0'
        option enabled '1'
        option uuid 'b7248e21-d71a-41a9-b9f6-acc384dc8673'
        option fstype 'ext3'

rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
/dev/sdb1 on /overlay type ext3 (rw,noatime,user_xattr,barrier=1,nodelalloc,data=ordered)
overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
/dev/sda1 on /tmp/overlay-disabled type ext3 (rw,noatime,user_xattr,barrier=1,nodelalloc,data=ordered)
none on /proc/bus/usb type usbfs (rw,relatime)

2013-06-19 06:24:21

Witam

Dorzuce swoje 5 groszy do tematu:

Na poczatek pare slow o konfiguracji

tp-link mr3420 v2 + 1.5.9.11 (r36557), by obsy -> hub modecom -> huawei u173-u2 +uSD 8GB [AT^U2DIAG=256] z exroot i swap'em

Wszystko pieknie dzialalo, do momentu kiedy przez przypadek zamiast wylaczyc router wcisnalem przycisk wps/resest. Router sie zresetowal (zakladam ze odpalilem firstboot ) i odpalil z flash'a.

Wrzucilem do /etc/fstab/config odpowiednie "formulki", skasowalem wszystkie *extroot.md5* i .. nic dalej startuje z flash'a. Pałowalem sie tak dobra godzine i nic, dalej niechcial odpalic extroot'a montujac go do tmp/overlay-disable.

Przerzucilem system (extroot) z huawei u173-u2 +uSD 8GB na Pendrive'a wrzucilem do /etc/config/fstab co trzeba. z pendrive'a wszystko pieknie startuje. Wiec znowu do /etc/config/fstab wrzucilem uuid uSD 8GB i co dziwne, dalej startuje z pendrive'a a nie z huawei u173-u2 +uSD 8GB mimo, ze z z fstab'u i /config/fstab wynika ze powiniem startowac z uSD 8GB

Dla ustalenia uwagi:
/dev/sdb2: UUID="170da887-92d0-42b0-9205-a3fd021869b5" TYPE="swap"
/dev/sdb1: UUID="0c211d73-1eca-4520-b596-9c630cc4bf03" TYPE="ext3"
/dev/sda2: UUID="8f32387a-dbf0-46a4-92b4-49f8de1620a1" TYPE="swap"
/dev/sda1: UUID="b7248e21-d71a-41a9-b9f6-acc384dc8673" TYPE="ext3"

oraz /etc/config/fstab:

  GNU nano 2.2.6                                                       File: /etc/config/fstab                                                                                                                      


config global 'automount'
        option from_fstab '1'
        option anon_mount '1'

config global 'autoswap'
        option from_fstab '1'
        option anon_swap '0'

config mount
        option target '/overlay'
        option device '/dev/sda98'
        option options 'rw,noatime'
        option enabled_fsck '0'
        option enabled '1'
        option uuid 'b7248e21-d71a-41a9-b9f6-acc384dc8673'
        option fstype 'ext3'

config swap
        option device '/dev/sda2'
        option uuid '8f32387a-dbf0-46a4-92b4-49f8de1620a1'
        option enabled '1'

/etc/fstab:

/dev/sda1       /overlay        ext3    rw,noatime      0       0
/dev/sda2       none    swap    sw      0       0

oraz mount:

rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
/dev/sdb1 on /overlay type ext3 (rw,noatime,user_xattr,barrier=1,nodelalloc,data=ordered)
overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
/dev/sda1 on /tmp/overlay-disabled type ext3 (rw,noatime,user_xattr,barrier=1,nodelalloc,data=ordered)
none on /proc/bus/usb type usbfs (rw,relatime)

oczywiscie za kazdym razem kasuje sumy kontrolne. moje pytanie jest nastepujace. dlaczego system startuje z pendrive'a a nie z flash'a ? gdzies sa jeszcze jakies pliki konfiguracyjne, ktore mowia systemowi, ze ma startowac z pen'a a nie z flash'a ?

mam nadzieje, ze nie zamieszalem z bardzo. meritum sprawy wyglada tak

dzialal extroot na uSD8GB, po resecie przestal. przerzucenie systemu z uSD8GB na pendrive sprawilo, ze startuje z pendrive'a. proba odpalenia extroot'a z uSD8GB konczy sie odpaleniem go z pendrive'a ?? a nie jak zdrowy rozsadek by podpowiadal z flash'a (skoro z jakis powodow niechce odpalic go z uSD8GB)

dodam, ze partycje swap montuje, z karty uSD wpietej do modemu

Pozdrawiam

2013-06-03 19:22:14

Witam

czy ktos z forumowiczow, przerabial jakis "lightweight'owy" serwer dla squeezbox'a, ktory dziala pod openwrt ?

Karol

2013-05-24 15:21:58

Witam

Wszystko dziala. Dziekuje za pomoc.

Temat uwazam za zamkniety

Pozdrawiam

2013-05-23 22:16:13

Witam

opkg install kmod-usb-storage-extras
ERROR: Dependency kernel (= 3.3.8-1-d6597ebf6203328d3519ea3c3371a493) of package kmod-usb-storage-extras is installed,
but has incompatible version 3.3.8-1-3b70fc7d412617eb97c6bdc7d8fb7844 and is marked as 'hold'
Pozdrawiam
Karol

2013-05-23 17:20:44

Witam wszystkich

mam nastepujacy problem, z ktorym nie potrafie sobie poradzic.

Moze zaczna od konfiguracji sprzetowej

tp-link mr3420 v2 + 1.5.9.11 (r36557), by obsy -> hub modecom -> huawei u173-u2 +uSD 8GB z exroot i swap'em + dysk zewnetrzny 2.5" usb (kieszen firmy TREKSTOR dysk FUJITSU 80GB)

A problem polega na tym, ze nie moge tego dysku zamontowac.

.- fdisk go niewidzi
.- wydajac polecenie cat /proc/bus/usb/devices widzi, tylko modem, i pendrive ktory jest wpiety do hub'a
.- lsusb wykazuje, ze system widzi kieszen (log ponizej)

 T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  1/800 us ( 0%), #Int=  3, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.03
S:  Manufacturer=Linux 3.3.8 ehci_hcd
S:  Product=Generic Platform EHCI Controller
S:  SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev= 1.11
S:  Product=USB 2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev= 1.11
S:  Product=USB 2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=256ms

T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=04b4 ProdID=6830 Rev= 0.01
S:  Manufacturer= 
S:  Product= 
S:  SerialNumber=D
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=03 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0781 ProdID=5571 Rev= 1.22
S:  Manufacturer=SanDisk
S:  Product=Cruzer Fit
S:  SerialNumber=4C532000030922116275
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=200mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=04 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1001 Rev= 0.00
S:  Manufacturer=HUAWEI Technology
S:  Product=HUAWEI Mobile
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

lsusb

 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 1a40:0101 TERMINUS TECHNOLOGY INC. USB-2.0 4-Port HUB
Bus 001 Device 003: ID 1a40:0101 TERMINUS TECHNOLOGY INC. USB-2.0 4-Port HUB
Bus 001 Device 004: ID 0781:5571 SanDisk Corp. 
Bus 001 Device 005: ID 12d1:1001 Huawei Technologies Co., Ltd. E169/E620/E800 HSDPA Modem
Bus 001 Device 006: ID 04b4:6830 Cypress Semiconductor Corp. CY7C68300A EZ-USB AT2 USB 2.0 to ATA/ATAPI

kieszn z dyskiej to urzadzenie nr 6

dmesg

[    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #96 Mon May 6 15:06:11 CEST 2013
[    0.000000] MyLoader: sysp=7e32261f, boardp=2eeaf96f, parts=7e16f0c5
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9341 rev 1
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802f7d00, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-MR3420-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28968k/32768k available (2233k kernel code, 3800k reserved, 423k data, 216k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-MR3420 v2
[    0.520000] bio: create slab <bio-0> at 0
[    0.520000] Switching to clocksource MIPS
[    0.530000] NET: Registered protocol family 2
[    0.530000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.540000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.550000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.550000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.560000] TCP reno registered
[    0.560000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.570000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.570000] NET: Registered protocol family 1
[    0.580000] PCI: CLS 0 bytes, default 32
[    0.590000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.600000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.610000] msgmni has been set to 56
[    0.610000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.620000] io scheduler noop registered
[    0.630000] io scheduler deadline registered (default)
[    0.630000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.660000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.670000] console [ttyS0] enabled, bootconsole disabled
[    0.680000] m25p80 spi0.0: found s25sl032a, expected m25p80
[    0.690000] m25p80 spi0.0: s25sl032a (4096 Kbytes)
[    0.690000] 5 tp-link partitions found on MTD device spi0.0
[    0.700000] Creating 5 MTD partitions on "spi0.0":
[    0.710000] 0x000000000000-0x000000020000 : "u-boot"
[    0.710000] 0x000000020000-0x00000010c378 : "kernel"
[    0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.730000] 0x00000010c378-0x0000003f0000 : "rootfs"
[    0.740000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.750000] mtd: partition "rootfs" set to be root filesystem
[    0.760000] mtd: partition "rootfs_data" created automatically, ofs=390000, len=60000 
[    0.770000] 0x000000390000-0x0000003f0000 : "rootfs_data"
[    0.770000] 0x0000003f0000-0x000000400000 : "art"
[    0.780000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.810000] ag71xx_mdio: probed
[    0.810000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.370000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[    1.380000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    1.930000] eth1: Found an AR934X built-in switch
[    2.970000] TCP cubic registered
[    2.970000] NET: Registered protocol family 17
[    2.970000] Bridge firewalling registered
[    2.980000] Ebtables v2.0 registered
[    2.980000] 8021q: 802.1Q VLAN Support v1.8
[    2.990000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    3.000000] Freeing unused kernel memory: 216k freed
[    4.950000] Registered led device: tp-link:green:lan1
[    4.950000] Registered led device: tp-link:green:lan2
[    4.950000] Registered led device: tp-link:green:lan3
[    4.950000] Registered led device: tp-link:green:lan4
[    4.950000] Registered led device: tp-link:green:qss
[    4.950000] Registered led device: tp-link:green:system
[    4.950000] Registered led device: tp-link:green:wan
[    4.950000] Registered led device: tp-link:green:wlan
[    4.960000] Registered led device: tp-link:green:3g
[    8.270000] JFFS2 notice: (453) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (1 unchecked, 0 orphan) and 339 of xref (0 dead, 49 orphan) found.
[    8.980000] SCSI subsystem initialized
[    9.180000] usbcore: registered new interface driver usbfs
[    9.180000] usbcore: registered new interface driver hub
[    9.190000] usbcore: registered new device driver usb
[    9.660000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.670000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[    9.670000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    9.710000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    9.730000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    9.730000] hub 1-0:1.0: USB hub found
[    9.740000] hub 1-0:1.0: 1 port detected
[    9.790000] Initializing USB Mass Storage driver...
[    9.790000] usbcore: registered new interface driver usb-storage
[    9.800000] USB Mass Storage support registered.
[   10.060000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   10.210000] hub 1-1:1.0: USB hub found
[   10.210000] hub 1-1:1.0: 4 ports detected
[   10.500000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
[   10.630000] hub 1-1.1:1.0: USB hub found
[   10.630000] hub 1-1.1:1.0: 4 ports detected
[   10.720000] usb 1-1.3: new high-speed USB device number 4 using ehci-platform
[   10.850000] scsi0 : usb-storage 1-1.3:1.0
[   10.950000] usb 1-1.4: new high-speed USB device number 5 using ehci-platform
[   11.080000] scsi4 : usb-storage 1-1.4:1.3
[   11.850000] scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer Fit       1.22 PQ: 0 ANSI: 5
[   11.860000] sd 0:0:0:0: [sda] 7821312 512-byte logical blocks: (4.00 GB/3.72 GiB)
[   11.870000] sd 0:0:0:0: [sda] Write Protect is off
[   11.870000] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[   11.880000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   11.890000]  sda: sda1
[   11.900000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   12.090000] scsi 4:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
[   12.100000] sd 4:0:0:0: [sdb] 15552512 512-byte logical blocks: (7.96 GB/7.41 GiB)
[   12.110000] sd 4:0:0:0: [sdb] Write Protect is off
[   12.110000] sd 4:0:0:0: [sdb] Mode Sense: 0f 0e 00 00
[   12.110000] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   12.130000]  sdb: sdb1 sdb2
[   12.140000] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[   30.740000] EXT4-fs (sdb1): mounting ext3 file system using the ext4 subsystem
[   30.840000] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[   31.970000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[   31.980000] Backport based on wireless-testing.git master-2013-02-22
[   31.990000] compat.git: wireless-testing.git
[   32.150000] cfg80211: Calling CRDA to update world regulatory domain
[   32.150000] cfg80211: World regulatory domain updated:
[   32.160000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   32.170000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   32.170000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   32.980000] ath: EEPROM regdomain: 0x0
[   32.980000] ath: EEPROM indicates default country code should be used
[   32.980000] ath: doing EEPROM country->regdmn map search
[   32.980000] ath: country maps to regdmn code: 0x3a
[   32.980000] ath: Country alpha2 being used: US
[   32.980000] ath: Regpair used: 0x3a
[   32.980000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   32.990000] Registered led device: ath9k-phy0
[   32.990000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[   32.990000] cfg80211: Calling CRDA for country: US
[   33.000000] cfg80211: Regulatory domain changed to country: US
[   33.010000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   33.010000] cfg80211:   (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   33.020000] cfg80211:   (5140000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[   33.220000] PPP generic driver version 2.4.2
[   33.280000] tun: Universal TUN/TAP device driver, 1.6
[   33.290000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   33.380000] GRE over IPv4 demultiplexor driver
[   33.400000] ip_gre: Unknown symbol icmpv6_send (err 0)
[   33.510000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   33.980000] NET: Registered protocol family 24
[   34.110000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[   34.440000] PPTP driver version 0.8.5
[   35.040000] xt_time: kernel timezone is -0000
[   35.740000]     Hooked IMQ after mangle on PREROUTING
[   35.750000]     Hooked IMQ after nat on POSTROUTING
[   35.750000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[   35.930000] Netfilter messages via NETLINK v0.30.
[   35.980000] ip_set: protocol 6
[   36.580000] usbcore: registered new interface driver cdc_acm
[   36.580000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   36.710000] usbcore: registered new interface driver usbserial
[   36.720000] USB Serial support registered for generic
[   36.720000] usbcore: registered new interface driver usbserial_generic
[   36.730000] usbserial: USB Serial Driver core
[   36.770000] usbcore: registered new interface driver cdc_ether
[   36.840000] usbcore: registered new interface driver cdc_ncm
[   36.930000] USB Serial support registered for GSM modem (1-port)
[   36.940000] option 1-1.4:1.0: GSM modem (1-port) converter detected
[   36.950000] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB0
[   36.950000] option 1-1.4:1.1: GSM modem (1-port) converter detected
[   36.960000] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB1
[   36.970000] option 1-1.4:1.2: GSM modem (1-port) converter detected
[   36.980000] usb 1-1.4: GSM modem (1-port) converter now attached to ttyUSB2
[   36.980000] usbcore: registered new interface driver option
[   36.990000] option: v0.7.2:USB Driver for GSM modems
[   37.090000] USB Serial support registered for Sierra USB modem
[   37.100000] usbcore: registered new interface driver sierra
[   37.110000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[   39.880000] Adding 249836k swap on /dev/sdb2.  Priority:-1 extents:1 across:249836k 
[   44.010000] device eth1 entered promiscuous mode
[   44.610000] eth1: link up (1000Mbps/Full duplex)
[   44.610000] br-lan: port 1(eth1) entered forwarding state
[   44.620000] br-lan: port 1(eth1) entered forwarding state
[   46.620000] br-lan: port 1(eth1) entered forwarding state
[   49.350000] device wlan0 entered promiscuous mode
[   49.590000] br-lan: port 2(wlan0) entered forwarding state
[   49.600000] br-lan: port 2(wlan0) entered forwarding state
[   51.600000] br-lan: port 2(wlan0) entered forwarding state
[   88.650000] ipt_bandwidth: timezone shift of 120 minutes detected, adjusting
[   88.660000]                old minutes west=0, new minutes west=-120
[   98.280000] head: sending ioctl 540d to a partition!
[   98.280000] head: sending ioctl 540d to a partition!
[  100.420000] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities
[  100.430000] EXT4-fs (sda1): couldn't mount as ext2 due to feature incompatibilities
[  100.440000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[  100.770000] head: sending ioctl 540d to a partition!
[  100.780000] head: sending ioctl 540d to a partition!
[  102.690000] head: sending ioctl 540d to a partition!
[  102.700000] head: sending ioctl 540d to a partition!
[  188.160000] usb 1-1.2: new high-speed USB device number 6 using ehci-platform

nie wazne jaki system plikow ustawie na dysku (ext2,3,4 ; ntfs) jest on niewidoczny

ponizej fdisk -l

Disk /dev/mtdblock0: 0 MB, 131072 bytes
255 heads, 63 sectors/track, 0 cylinders, total 256 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock1: 0 MB, 967168 bytes
255 heads, 63 sectors/track, 0 cylinders, total 1889 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock2: 3 MB, 3030016 bytes
255 heads, 63 sectors/track, 0 cylinders, total 5918 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock3: 0 MB, 393216 bytes
255 heads, 63 sectors/track, 0 cylinders, total 768 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock4: 0 MB, 65536 bytes
255 heads, 63 sectors/track, 0 cylinders, total 128 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/mtdblock5: 3 MB, 3997696 bytes
255 heads, 63 sectors/track, 0 cylinders, total 7808 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes


Disk /dev/sda: 4004 MB, 4004511744 bytes
255 heads, 63 sectors/track, 486 cylinders, total 7821312 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00347f3e

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1   *          63     7821311     3910624+   7  HPFS/NTFS/exFAT

Disk /dev/sdb: 7962 MB, 7962886144 bytes
245 heads, 62 sectors/track, 1023 cylinders, total 15552512 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1            2048    15052828     7525390+  83  Linux
/dev/sdb2        15052829    15552511      249841+  82  Linux swap / Solaris

ma ktos jakis pomysl ?

Pozdrawiam
Karol

FAQ o OpenWrt | Sprzedam różne routery | Oddam

Opcje wyszukiwania (Strona 2 z 2)

Znalezione posty: 26 do 31 z 31

26 Odpowiedź przez karol04 2013-06-19 11:30:48

Odp: [howto] Extroot dla Gargoyle na TL-MR3420/MR3220/MR3020/MR3040 (934 odpowiedzi, napisanych Oprogramowanie / Software)

27 Odpowiedź przez karol04 2013-06-19 06:24:21

Odp: [howto] Extroot dla Gargoyle na TL-MR3420/MR3220/MR3020/MR3040 (934 odpowiedzi, napisanych Oprogramowanie / Software)

28 Temat przez karol04 2013-06-03 19:22:14

Temat: Squeezbox+Openwrt (0 odpowiedzi, napisanych Oprogramowanie / Software)

29 Odpowiedź przez karol04 2013-05-24 15:21:58

Odp: Problem z dyskiem zewnetrzym (4 odpowiedzi, napisanych Oprogramowanie / Software)

30 Odpowiedź przez karol04 2013-05-23 22:16:13

Odp: Problem z dyskiem zewnetrzym (4 odpowiedzi, napisanych Oprogramowanie / Software)

31 Temat przez karol04 2013-05-23 17:20:44

Temat: Problem z dyskiem zewnetrzym (4 odpowiedzi, napisanych Oprogramowanie / Software)

Znalezione posty: 26 do 31 z 31