zle mnie zrozumiales
pod tym adresem jest wszystko ok
chodzi mi o to czy w gui luci w zakladce MJPG-streamer moge uzyskac podgląd live tak jak to miałem w gui gargoyle w zakladce wekcam ?

MJPG-streamer

# Redirect HTTP requests to HTTPS if possible
        option redirect_https   1

to zmienić na 0 ?

co to znaczy "głupiego ap" ?

root@Sypialnia:~# uci show network
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fdc7:733b:6142::/48'
network.lan=interface
network.lan.type='bridge'
network.lan.proto='static'
network.lan.netmask='255.255.255.0'
network.lan.ip6assign='60'
network.lan.ipaddr='10.0.1.20'
network.lan.gateway='10.0.1.1'
network.lan.ifname='eth0 eth0.1 eth0.2'
network.lan.dns='8.8.8.8 8.8.4.4'
network.lan_dev=device
network.lan_dev.name='eth0.1'
network.lan_dev.macaddr='a4:2b:8c:0d:41:2f'
network.wan=interface
network.wan.ifname='eth0.2'
network.wan.proto='dhcp'
network.wan.type='bridge'
network.wan_dev=device
network.wan_dev.name='eth0.2'
network.wan_dev.macaddr='a4:2b:8c:0d:41:30'
network.wan6=interface
network.wan6.ifname='eth0.2'
network.wan6.proto='dhcpv6'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='1 2 3 4 0t'
network.@switch_vlan[1]=switch_vlan
network.@switch_vlan[1].device='switch0'
network.@switch_vlan[1].vlan='2'
network.@switch_vlan[1].ports='5 0t'
network.Most=interface
network.Most.type='bridge'
network.Most.proto='static'
network.Most.ifname='eth0 eth0.1 eth0.2'
network.Most.ipaddr='10.0.1.20'
network.Most.netmask='255.255.255.0'
network.Most.gateway='10.0.1.1'
network.Most.dns='10.0.1.1'

root@Sypialnia:~# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         10.0.1.1        0.0.0.0         UG    0      0        0 br-Most
10.0.1.0        0.0.0.0         255.255.255.0   U     0      0        0 br-Most

W gargoyle po instalacji zmieniłem adres routera na 10.0.1.20 wpisałem jako brame 10.0.1.1 ustawiłem hasło do wifi i tyle

# uci set network.lan.ipaddr=10.0.1.20
    # uci set network.lan.gateway=10.0.1.1
    # uci set network.lan.dns='8.8.8.8 8.8.4.4'
    # uci commit network
    # reboot
Zrobiłem tak jak podałeś w linku ze swoimi adresami
i dalej mam
opkg update
Downloading http://downloads.openwrt.org/releases/1 … ackages.gz
*** Failed to download the package list from http://downloads.openwrt.org/releases/1 … ackages.gz

Ale ja mam dostęp do internetu na strony wchodzę normalnie tylko  gdy chce zaktualizować pakiety to jest error

dla gargoyle ?

po zainstalowaniu sane-backends-all i wydaniu polecenia

# sane-find-scanner  dostałem coś takiego

  # sane-find-scanner will now attempt to detect your scanner. If the
  # result is different from what you expected, first make sure your
  # scanner is powered up and properly connected to your computer.

  # No SCSI scanners found. If you expected something different, make sure that
  # you have loaded a kernel SCSI driver for your SCSI adapter.
  # Also you need support for SCSI Generic (sg) in your operating system.
  # If using Linux, try "modprobe sg".

found USB scanner (vendor=0x03f0 [HP], product=0x7d04 [Deskjet F2100 series]) at libusb:001:007
  # Your USB scanner was (probably) detected. It may or may not be supported by
  # SANE. Try scanimage -L and read the backend's manpage.

  # Not checking for parallel port scanners.

  # Most Scanners connected to the parallel port or other proprietary ports
  # can't be detected by this program.

a scanimage -L

o scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).

mam rozumiec to tak ze w sane-backends-all nie mam sterownika ?

router na ktorym chce to uruchomic to netgear 4300 a system to ostatni twoj obraz gargoyle
Nie moge teraz usunac w gui tego dodanego adresu