1

Temat: lm_sensors

Witam.
Mam pytanko dot. sensorów na płycie gł. Czy lm_sensors działa na mandarynce ?? Dodam iż mam Aristo Smart 440

Pozdrawiam

2

Odp: lm_sensors

Ogólnie: a czemu miało by nie działać. A szczegółowo - a masz w 440 jakieś sensory? Bo w 400 nie jest nic wykrywane.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

3

Odp: lm_sensors

[root@localhost tomson]# sensors-detect
# sensors-detect revision 4271 (2006-12-26 03:53:20 -0800)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): y
Probing for PCI bus adapters...
Use driver `i2c-i801' for device 0000:00:1f.3: Intel 82801G ICH7

We will now try to load each adapter module in turn.
Module `i2c-i801' already loaded.
If you have undetectable or unsupported adapters, you can have them
scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
Do you want to load `i2c-dev' now? (YES/no): y
Module loaded successfully.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Next adapter: SMBus I801 adapter at 18c0 (i2c-0)
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x08
Client found at address 0x44
Probing for `Maxim MAX6633/MAX6634/MAX6635'...              No
Client found at address 0x50
Handled by driver `eeprom' (already loaded), chip type `eeprom'
Client found at address 0x52
Handled by driver `eeprom' (already loaded), chip type `eeprom'
Client found at address 0x69

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): y
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM78-J' at 0x290...     No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No
Probing for `Winbond W83627HF' at 0x290...                  No
Probing for `Silicon Integrated Systems SIS5595'...         No
Probing for `VIA VT82C686 Integrated Sensors'...            No
Probing for `VIA VT8231 Integrated Sensors'...              No
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `ITE'...                                      No
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No
Probing for Super-I/O at 0x4e/0x4f
Trying family `ITE'...                                      No
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No

Some CPUs or memory controllers may also contain embedded sensors.
Do you want to scan for them? (YES/no): y
AMD K8 thermal sensors...                                   No
Intel Core family thermal sensor...                         Success!
    (driver `coretemp')
Intel AMB FB-DIMM thermal sensor...                         No

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `eeprom' (should be inserted):
  Detects correctly:
  * Bus `SMBus I801 adapter at 18c0'
    Busdriver `i2c-i801', I2C address 0x50
    Chip `eeprom' (confidence: 6)
  * Bus `SMBus I801 adapter at 18c0'
    Busdriver `i2c-i801', I2C address 0x52
    Chip `eeprom' (confidence: 6)

  EEPROMs are *NOT* sensors! They are data storage chips commonly
  found on memory modules (SPD), in monitors (EDID), or in some
  laptops, for example.

Driver `coretemp' (should be inserted):
  Detects correctly:
  * Chip `Intel Core family thermal sensor' (confidence: 9)

I will now generate the commands needed to load the required modules.
Just press ENTER to continue:

To make the sensors modules behave correctly, add these lines to
/etc/modules.conf:

#----cut here----
# I2C module options
alias char-major-89 i2c-dev
#----cut here----

To load everything that is needed, add this to some /etc/rc* file:

#----cut here----
# I2C adapter drivers
modprobe i2c-i801
# Chip drivers
modprobe eeprom
# Warning: the required module coretemp is not currently installed
# on your system. For status of 2.6 kernel ports check
# http://www.lm-sensors.org/wiki/Devices. If driver is built
# into the kernel, or unavailable, comment out the following line.
modprobe coretemp
# sleep 2 # optional
/usr/local/bin/sensors -s # recommended
#----cut here----

If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones! You really
should try these commands right now to make sure everything is
working properly. Monitoring programs won't work until the needed
modules are loaded.

Do you want to overwrite /etc/sysconfig/lm_sensors? (YES/no): y

tak po krótce wygląda konf. sensorów

niby coś jest ale niema... sad

4

Odp: lm_sensors

Znalazł tylko coretemp, Czyli masz jakieś intel core lub duo. Powinieneś mieć wskaźnik temperatury procesora.  Więc

modprobe i2c-i801
modprobe eeprom
modprobe coretemp
/usr/local/bin/sensors -s

I powinieneś dostać temperaturę procka.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

5

Odp: lm_sensors

ładuję moduły
[root@localhost tomson]# modprobe i2c-i801
[root@localhost tomson]# modprobe eeprom
[root@localhost tomson]# modprobe coretemp
FATAL: Module coretemp not found.

i jak widać jest problem z coretemp

a mam centrino duo...

6

Odp: lm_sensors

Nie, ty po prostu nie masz skompilowanego tego modułu...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

7

Odp: lm_sensors

Moduł coretemp jest w jądze 2.6.22 ja mam 2.6.17-15. Nie bardzo wiem jak sie zabrać do kompilacji...

8

Odp: lm_sensors

Dokładnie. Coretemp jest dopiero od 2.6.22... Znajdź nowsze jądro do mandarynki (pewnie w cookerze będzie) jeżeli nie chcesz/nie umiesz kompilować.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

9

Odp: lm_sensors

znalazłem jądro 2.6.22 - no i sensorki działaja, ale pojawił sie problem z wifi i dźwiękiem... coś za coś. Zabieram się do rozwiązania tych dwóch spraw.

10

Odp: lm_sensors

Witam, czy ktoś z szanownych forumowiczów posiada compala fl90 lub ifl92 i udało mu się uruchomić lm-sensors? Chodzi mi głównie o coretemp. Posiadam fl90 c t8300, niestety sensors-detect nie wykrywa żadnych sensorów sad Googlalem ale nic nie znalazłem. Jedyne co udało mi sie uruchomić to temperatura hdd oraz GPU.
Moja dystrybucja to Ubuntu 8.04 więc w jądrze powinien być moduł coretemp.ko (jest fizycznie plik ale przy modprobe coretemp mówi że brak urządzenia)

Pozdrawiam

11

Odp: lm_sensors

Obsługa penrynów została dodana do coretemp dopiero w 2.6.25, więc zaktualizuj sobie jądro (Ubuntu ma 2.6.24).

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

12

Odp: lm_sensors

Po udanej kompilacji jajka do 2.6.25 wszystko działą jak należy.
Dziękuję za szybką odpowiedź