Temat: Transmission - niestabilność, errory, błędy w ściągniętych danych

Kilka dni temu przeprowadziłem pełną reinstalację Gargoyle (1.5.9.3 (r35400))- swap, extroot i Transmission + vsftp. Wcześniej jako magazyn miałem dysk na ext2. Teraz oczywiście extroot jest na ext4 ale w jednym folderze mam podmontowaną partycję ntfs na której mam konfigurację transmission oraz ściągnięte pliki. Niestety o ile wcześniej nie było problemów to teraz często w losowych momentach (zwykle co około godzinę ) mam komunikaty typu Error: Please Verify Local Data! Piece #tutajnumerczęści is corrupt.. To bardzo dziwne bo ujawniają się nawet w dawno ściągniętych torrentach. Czasem też w ogóle się trans wysupuje i nie pozwala mi wejść.

Więc pytanie czy to jest wina błędów na dysku czy po prostu współpraca transmission z ntfsem jest ryzykowna?

2

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Skoro masz już to w ściągniętych danych to prostu następuje przekłamanie przy odczycie z dysku. Więc sprawdź system plików, powierzchnię, zobacz logread czy nie masz czegoś w logach.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

3

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Miałem podobnie na ext4 z mniejszą częstotliwością, dysk skanowany po 100x, dociągłem torrenta po jakimś czasie to samo. Po wymianie dysko już się nie powtórzyło. Zrobiłem od nowa partycję, sformatowałem, i noszę się z zamiarem zaś go sprawdzić. Fakt ma on powody, ma już 5 lat a torrenty naparzajały na nim 24/7. Nie są to bad block'i, i zdaję się jest coś w tym co Cezary napisał. S.M.A.R.T nie jest w dobrym stanie, ale nic krytycznego. W logach nic nie było hmm .

4

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Po usunięciu partycji , zrobieniu od nowa problem zniknął...

5

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

jaki będzie najlepszy system plików na torrenty?

6

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Ja bym robił ext4.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

7

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Problem powrócił...

8

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Zawsze wraca ... sad
to nie windows, reinstalacja nie rozwiązuje problemu

9

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Nie robiłem reinstalacji, na tym dysku nie mam systemu. Zrobiłem od nowa partycję, system plików. Ciekaw jestem gdzie jest problem, ale wszystko na to wskazuję, że dysk.

10 (edytowany przez doman18 2013-03-11 10:34:24)

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

logread

Mar 11 09:31:01 Gargoyle daemon.info hostapd: wlan0: STA {adres mac} WPA: group key handshake completed (RSN)
Mar 11 09:34:44 Gargoyle daemon.err transmission-daemon[3567]: Game Of Thrones Season 1 - Complete read failed for "Game Of Thrones Season 1 - Complete/S01E10 - Fire and Blood.avi": Input/output error (inout.c:129)
Mar 11 09:34:44 Gargoyle daemon.err transmission-daemon[3567]: Game Of Thrones Season 1 - Complete Piece 1855, which was just downloaded, failed its checksum test (peer-mgr.c:1809)
Mar 11 09:34:46 Gargoyle daemon.err transmission-daemon[3567]: Game Of Thrones Season 1 - Complete read failed for "Game Of Thrones Season 1 - Complete/S01E08 - The Pointy End.avi": Input/output error (inout.c:129)
Mar 11 09:34:46 Gargoyle daemon.err transmission-daemon[3567]: Game Of Thrones Season 1 - Complete Piece 247, which was just downloaded, failed its checksum test (peer-mgr.c:1809)
Mar 11 09:34:46 Gargoyle daemon.err transmission-daemon[3567]: Game Of Thrones Season 1 - Complete read failed for "Game Of Thrones Season 1 - Complete/S01E05 - The Wolf and the Lion.avi": Input/output error (inout.c:129)
Mar 11 09:34:50 Gargoyle daemon.err transmission-daemon[3567]: Game Of Thrones Season 1 - Complete Piece 952, which was just downloaded, failed its checksum test (peer-mgr.c:1809)
Mar 11 09:34:50 Gargoyle daemon.err transmission-daemon[3567]: Game Of Thrones Season 1 - Complete read failed for "Game Of Thrones Season 1 - Complete/S01E04 - Cripples, Bastards and Broken Things.avi": Input/output error (inout.c:129)
Mar 11 09:34:52 Gargoyle daemon.err transmission-daemon[3567]: Game Of Thrones Season 1 - Complete read failed for "Game Of Thrones 

{tutaj kupa podobnych komunikatów}

Mar 11 09:43:30 Gargoyle daemon.err transmission-daemon[3567]: Insidious.2010.DVDRip.XviD-ViP3R read failed for "Insidious.2010.DVDRip.XviD-ViP3R/Insidious.2010.DVDRip.XviD-ViP3R.avi": Transport endpoint is not connected (inout.c:129)
Mar 11 09:43:42 Gargoyle daemon.err transmission-daemon[3567]: Couldn't save temporary file "/home/mount/torrenty/settings.json.tmp.fG3FWk": Transport endpoint is not connected (bencode.c:1746)
Mar 11 09:43:42 Gargoyle daemon.err transmission-daemon[3567]: Couldn't save temporary file "/home/mount/torrenty/dht.dat.tmp.RfLS6h": Transport endpoint is not connected (bencode.c:1746)
Mar 11 09:43:42 Gargoyle daemon.err transmission-daemon[3567]: Couldn't create "/home/mount": File exists (utils.c:575)
Mar 11 09:43:42 Gargoyle daemon.err transmission-daemon[3567]: Couldn't create "/home/mount/Game Of Thrones Season 1 - Complete": File exists (fdlimit.c:361)
Mar 11 09:43:42 Gargoyle daemon.err transmission-daemon[3567]: Game Of Thrones Season 1 - Complete tr_fdFileCheckout failed for "/home/mount/Game Of Thrones Season 1 - Complete/S01E08 - The Pointy End.avi.part": File exists (inout.c:103)
Mar 11 09:43:42 Gargoyle daemon.info transmission-daemon[3567]: Closing session
Mar 11 09:43:45 Gargoyle user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Mar 11 09:43:45 Gargoyle user.notice root: wps
Mar 11 09:43:45 Gargoyle user.notice root: pressed
Mar 11 09:43:45 Gargoyle user.notice root: wps
Mar 11 09:43:45 Gargoyle user.notice root: released
Mar 11 10:03:37 Gargoyle user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)

Pod wps mam podpisany restart transmission, ale demon nie wstaje. Gdy próbuję go ręcznie restartować...

oot@Gargoyle:/home# /etc/init.d/transmission restart
mkdir: can't create directory '/home/mount/': Transport endpoint is not connected
touch: /home/mount/torrenty/settings.json: Transport endpoint is not connected
/etc/rc.common: eval: line 1: can't create /home/mount/torrenty/settings.json: Transport endpoint is not connected
/etc/rc.common: eval: line 1: can't create /home/mount/torrenty/settings.json: Transport endpoint is not connected

{tak kilkadziesiąt razy}

wchodzę do katalogu z punktem montowania dla partycji (katalog mount)

root@Gargoyle:/# cd /home
root@Gargoyle:/home# ls
ls: ./mount: Transport endpoint is not connected

polecenie mount

root@Gargoyle:/home# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
/dev/sde3 on /overlay type ext4 (rw,sync,relatime,user_xattr,barrier=1,data=ordered)
overlayfs:/overlay on / type overlayfs (rw,relatime,lowerdir=/,upperdir=/overlay)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)
nfsd on /proc/fs/nfsd type nfsd (rw,relatime)
/dev/sde2 on /home/mount type fuseblk (rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096)

Jak widać sde2 niby jest podmontowana i dla pewności, jak próbuję zamontować...

root@Gargoyle:/home# mount /home/mount
Mount is denied because the NTFS volume is already exclusively opened.
The volume may be already mounted, or another software may use it which
could be identified for example by the help of the 'fuser' command.
mount: mounting /dev/sde2 on /home/mount failed: No such device

Pomaga dopiero restart routera.

PS. Robiłem w windowsie scan tej partycji i coś tam wykryło i ponoć naprawiło. Ale problem jak widać nadal istnieje.

PS2. Aha no i dmesg

    0.000000] Linux version 3.3.8 (cezary@eko.one.pl) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #18 Fri Feb 1 17:25:41 CET 2013
[    0.000000] MyLoader: sysp=040a100a, boardp=40044e88, parts=420a1089
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9132 rev 2
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802f5cf0, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 28976k/32768k available (2227k kernel code, 3792k reserved, 421k data, 216k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-WR1043ND
[    0.360000] bio: create slab <bio-0> at 0
[    0.370000] Switching to clocksource MIPS
[    0.380000] NET: Registered protocol family 2
[    0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.380000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.400000] TCP reno registered
[    0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.420000] NET: Registered protocol family 1
[    0.420000] PCI: CLS 0 bytes, default 32
[    0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.440000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.450000] msgmni has been set to 56
[    0.460000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.470000] io scheduler noop registered
[    0.470000] io scheduler deadline registered (default)
[    0.470000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.510000] console [ttyS0] enabled, bootconsole disabled
[    0.530000] m25p80 spi0.0: found s25sl064a, expected m25p80
[    0.530000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
[    0.540000] 5 tp-link partitions found on MTD device spi0.0
[    0.540000] Creating 5 MTD partitions on "spi0.0":
[    0.550000] 0x000000000000-0x000000020000 : "u-boot"
[    0.560000] 0x000000020000-0x00000010da00 : "kernel"
[    0.560000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.580000] 0x00000010da00-0x0000007f0000 : "rootfs"
[    0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.590000] mtd: partition "rootfs" set to be root filesystem
[    0.600000] mtd: partition "rootfs_data" created automatically, ofs=630000, len=1C0000 
[    0.610000] 0x000000630000-0x0000007f0000 : "rootfs_data"
[    0.620000] 0x0000007f0000-0x000000800000 : "art"
[    0.620000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.630000] Realtek RTL8366RB ethernet switch driver version 0.2.3
[    0.750000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[    0.750000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[    0.930000] rtl8366rb: probed
[    0.940000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.240000] TCP cubic registered
[    1.250000] NET: Registered protocol family 17
[    1.250000] Bridge firewalling registered
[    1.260000] Ebtables v2.0 registered
[    1.260000] 8021q: 802.1Q VLAN Support v1.8
[    1.270000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.280000] Freeing unused kernel memory: 216k freed
[    3.710000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[    3.710000] eth0: link up (1000Mbps/Full duplex)
[    3.870000] Registered led device: tp-link:green:usb
[    3.870000] Registered led device: tp-link:green:system
[    3.870000] Registered led device: tp-link:green:qss
[    3.880000] Registered led device: tp-link:green:wlan
[    7.190000] JFFS2 notice: (440) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 35 of xref (0 dead, 6 orphan) found.
[    8.100000] SCSI subsystem initialized
[    8.340000] usbcore: registered new interface driver usbfs
[    8.340000] usbcore: registered new interface driver hub
[    8.350000] usbcore: registered new device driver usb
[    9.010000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.010000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[    9.020000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    9.060000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    9.080000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    9.080000] hub 1-0:1.0: USB hub found
[    9.090000] hub 1-0:1.0: 1 port detected
[    9.150000] Initializing USB Mass Storage driver...
[    9.160000] usbcore: registered new interface driver usb-storage
[    9.170000] USB Mass Storage support registered.
[    9.420000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    9.570000] hub 1-1:1.0: USB hub found
[    9.570000] hub 1-1:1.0: 4 ports detected
[    9.860000] usb 1-1.3: new high-speed USB device number 3 using ehci-platform
[    9.970000] scsi0 : usb-storage 1-1.3:1.0
[   10.060000] usb 1-1.4: new high-speed USB device number 4 using ehci-platform
[   10.170000] scsi1 : usb-storage 1-1.4:1.0
[   10.970000] scsi 0:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
[   10.980000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   10.990000] scsi 0:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
[   10.990000] scsi 0:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
[   11.010000] scsi 0:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
[   11.020000] sd 0:0:0:1: [sdb] Attached SCSI removable disk
[   11.030000] sd 0:0:0:2: [sdc] Attached SCSI removable disk
[   11.040000] sd 0:0:0:3: [sdd] Attached SCSI removable disk
[   12.120000] scsi 1:0:0:0: Direct-Access              ST3160815A       3.AA PQ: 0 ANSI: 0 CCS
[   12.130000] sd 1:0:0:0: [sde] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[   12.240000] sd 1:0:0:0: [sde] Write Protect is off
[   12.240000] sd 1:0:0:0: [sde] Mode Sense: 00 00 00 00
[   12.360000] sd 1:0:0:0: [sde] Asking for cache data failed
[   12.360000] sd 1:0:0:0: [sde] Assuming drive cache: write through
[   12.570000] sd 1:0:0:0: [sde] Asking for cache data failed
[   12.570000] sd 1:0:0:0: [sde] Assuming drive cache: write through
[   12.590000]  sde: sde1 sde2 sde3
[   12.800000] sd 1:0:0:0: [sde] Asking for cache data failed
[   12.800000] sd 1:0:0:0: [sde] Assuming drive cache: write through
[   12.810000] sd 1:0:0:0: [sde] Attached SCSI disk
[   30.770000] EXT4-fs (sde3): recovery complete
[   30.780000] EXT4-fs (sde3): mounted filesystem with ordered data mode. Opts: (null)
[   31.010000] eth0: link down
[   31.800000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[   31.810000] Backport based on wireless-testing.git master-2012-09-07
[   31.810000] compat.git: wireless-testing.git
[   31.980000] cfg80211: Calling CRDA to update world regulatory domain
[   31.990000] cfg80211: World regulatory domain updated:
[   31.990000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   32.000000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.010000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   32.020000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   32.020000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   32.030000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   33.380000] ath: EEPROM regdomain: 0x0
[   33.380000] ath: EEPROM indicates default country code should be used
[   33.380000] ath: doing EEPROM country->regdmn map search
[   33.380000] ath: country maps to regdmn code: 0x3a
[   33.380000] ath: Country alpha2 being used: US
[   33.380000] ath: Regpair used: 0x3a
[   33.390000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   33.390000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[   33.400000] cfg80211: Calling CRDA for country: US
[   33.410000] cfg80211: Regulatory domain changed to country: US
[   33.410000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   33.420000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   33.430000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   33.440000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   33.440000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   33.450000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   33.460000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   33.700000] RPC: Registered named UNIX socket transport module.
[   33.710000] RPC: Registered udp transport module.
[   33.720000] RPC: Registered tcp transport module.
[   33.720000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   34.300000] PPP generic driver version 2.4.2
[   34.450000] tun: Universal TUN/TAP device driver, 1.6
[   34.460000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   34.590000] GRE over IPv4 demultiplexor driver
[   34.700000] ip_gre: Unknown symbol icmpv6_send (err 0)
[   35.050000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   35.170000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   35.600000] NET: Registered protocol family 24
[   35.760000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[   36.290000] PPTP driver version 0.8.5
[   37.090000] xt_time: kernel timezone is -0000
[   37.940000]     Hooked IMQ after mangle on PREROUTING
[   37.950000]     Hooked IMQ after nat on POSTROUTING
[   37.950000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[   38.140000] Netfilter messages via NETLINK v0.30.
[   38.380000] ip_set: protocol 6
[   39.020000] usbcore: registered new interface driver cdc_acm
[   39.030000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   39.190000] usbcore: registered new interface driver usblp
[   39.220000] usbcore: registered new interface driver usbserial
[   39.230000] USB Serial support registered for generic
[   39.230000] usbcore: registered new interface driver usbserial_generic
[   39.240000] usbserial: USB Serial Driver core
[   39.400000] usbcore: registered new interface driver ums-alauda
[   39.430000] usbcore: registered new interface driver ums-cypress
[   39.460000] usbcore: registered new interface driver ums-datafab
[   39.530000] usbcore: registered new interface driver ums-freecom
[   39.560000] usbcore: registered new interface driver ums-isd200
[   39.590000] usbcore: registered new interface driver ums-jumpshot
[   39.610000] usbcore: registered new interface driver ums-karma
[   39.640000] usbcore: registered new interface driver ums-sddr09
[   39.670000] usbcore: registered new interface driver ums-sddr55
[   39.700000] usbcore: registered new interface driver ums-usbat
[   39.790000] usbcore: registered new interface driver cdc_ether
[   39.840000] usbcore: registered new interface driver cdc_ncm
[   39.950000] USB Serial support registered for GSM modem (1-port)
[   39.960000] usbcore: registered new interface driver option
[   39.960000] option: v0.7.2:USB Driver for GSM modems
[   40.060000] USB Serial support registered for Sierra USB modem
[   40.070000] usbcore: registered new interface driver sierra
[   40.070000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[   40.210000] fuse init (API version 7.18)
[   45.510000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[   45.810000] eth0: link up (1000Mbps/Full duplex)
[   45.810000] device eth0.1 entered promiscuous mode
[   45.820000] device eth0 entered promiscuous mode
[   45.820000] br-lan: port 1(eth0.1) entered forwarding state
[   45.830000] br-lan: port 1(eth0.1) entered forwarding state
[   47.830000] br-lan: port 1(eth0.1) entered forwarding state
[   49.640000] cfg80211: Calling CRDA for country: PL
[   49.650000] cfg80211: Regulatory domain changed to country: PL
[   49.650000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   49.660000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   49.670000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   49.680000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   49.680000] cfg80211:   (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[   51.890000] device wlan0 entered promiscuous mode
[   52.210000] br-lan: port 2(wlan0) entered forwarding state
[   52.220000] br-lan: port 2(wlan0) entered forwarding state
[   54.220000] br-lan: port 2(wlan0) entered forwarding state
[   91.770000] ipt_bandwidth: timezone shift of 60 minutes detected, adjusting
[   91.780000]                old minutes west=0, new minutes west=-60
[   96.640000] head: sending ioctl 540d to a partition!
[   96.640000] head: sending ioctl 540d to a partition!
[   97.680000] Adding 65532k swap on /dev/sde1.  Priority:-1 extents:1 across:65532k 
[   99.470000] head: sending ioctl 540d to a partition!
[   99.470000] head: sending ioctl 540d to a partition!
[  102.100000] head: sending ioctl 540d to a partition!
[  102.100000] head: sending ioctl 540d to a partition!

11

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Pozbądź się tego ntfs na nośniku.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

12

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Właśnie o tym myślałem, ale sądziłem że problem jest związany z jakimś babolem który sam popełniłem podczas konfiguracji ntfsa. Jak tylko dobiję ratio 2.0 dla Game of thrones, zwijam ntfsa i wrzucam ext3.

13

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Chcę tylko przekazać że przejście na ext3 zdecydowanie poprawiło sytuację. Zostawiłem na noc kilka torrentów ściągających się naraz z dość dużą prędkością i wszystkie ładnie się ściągnęły bez errorów. W jednym tylko był data corrupt ale takie rzeczy to błahostka bo po weryfikacji tą cząstkę można ściągnąć jeszcze raz. Nie wiem tylko czy dobry system plików wybrałem bo z TEGO wpisu wynika że różnica między nim a ext4 jest znaczna. Chyba , bo niżej piszą coś o złych wykresach itp.

Tak czy inaczej nie polecam NTFS do jakichkolwiek zastosowań przy OpenWRT

14

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Mam problem z transsmitionem a przynajmniej tak mi się wydaje, że to on jest sprawcą całego zamieszania. Chodzi o to, że jak odpalam go to po jakimś czasie kończy mi sie pamięć flash pomimo faktu, ze wszystko jest ściągane na pendrive. Czy ktoś się z takimś czymś spotkał? Dodam, że powoduje to również zaprzestanie działania samby i nie można się dostać do zasobów tego pena oraz dokonać żadnych zmian w plikach konfiguracyjnych bo krzyczy, ze nie ma miejsca. Prosżę o pomoc. Dziękuję

15

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Pokaż uci show transmission

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

16

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

root@OpenWrt:~# uci show transmission
transmission.@transmission[0]=transmission
transmission.@transmission[0].alt_speed_enabled='false'
transmission.@transmission[0].bind_address_ipv4='0.0.0.0'
transmission.@transmission[0].bind_address_ipv6='::'
transmission.@transmission[0].blocklist_enabled='false'
transmission.@transmission[0].cache_size_mb='2'
transmission.@transmission[0].dht_enabled='true'
transmission.@transmission[0].download_queue_enabled='true'
transmission.@transmission[0].download_queue_size='4'
transmission.@transmission[0].encryption='1'
transmission.@transmission[0].idle_seeding_limit_enabled='false'
transmission.@transmission[0].incomplete_dir_enabled='false'
transmission.@transmission[0].lazy_bitfield_enabled='true'
transmission.@transmission[0].lpd_enabled='false'
transmission.@transmission[0].message_level='1'
transmission.@transmission[0].peer_limit_global='240'
transmission.@transmission[0].peer_limit_per_torrent='60'
transmission.@transmission[0].peer_port='51413'
transmission.@transmission[0].peer_port_random_on_start='false'
transmission.@transmission[0].peer_socket_tos='default'
transmission.@transmission[0].pex_enabled='true'
transmission.@transmission[0].port_forwarding_enabled='true'
transmission.@transmission[0].preallocation='1'
transmission.@transmission[0].queue_stalled_enabled='true'
transmission.@transmission[0].queue_stalled_minutes='30'
transmission.@transmission[0].ratio_limit_enabled='false'
transmission.@transmission[0].rpc_authentication_required='false'
transmission.@transmission[0].rpc_bind_address='0.0.0.0'
transmission.@transmission[0].rpc_enabled='true'
transmission.@transmission[0].rpc_port='9091'
transmission.@transmission[0].rpc_url='/transmission/'
transmission.@transmission[0].rpc_whitelist='127.0.0.1,192.168.1.*'
transmission.@transmission[0].rpc_whitelist_enabled='true'
transmission.@transmission[0].scrape_paused_torrents_enabled='true'
transmission.@transmission[0].script_torrent_done_enabled='false'
transmission.@transmission[0].seed_queue_enabled='false'
transmission.@transmission[0].speed_limit_down_enabled='false'
transmission.@transmission[0].speed_limit_up_enabled='false'
transmission.@transmission[0].start_added_torrents='true'
transmission.@transmission[0].trash_original_torrent_files='false'
transmission.@transmission[0].umask='18'
transmission.@transmission[0].upload_slots_per_torrent='14'
transmission.@transmission[0].utp_enabled='true'
transmission.@transmission[0].scrape_paused_torrents='true'
transmission.@transmission[0].watch_dir_enabled='false'
transmission.@transmission[0].enabled='1'
transmission.@transmission[0].config_dir='/mnt/sda1/torrenty/konfiguracja'
transmission.@transmission[0].rename_partial_files='false'
transmission.@transmission[0].download_dir='/mnt/sda1/'
root@OpenWrt:~#

17

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Wygląda nieźle. Upewnij się że transmission startuje PO zamontowaniu dysku  a nie odwrotnie. Pamiętaj że dyski montują się asynchronicznie.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

18 (edytowany przez smereka 2017-03-21 21:34:12)

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Cezary ale mam problem bo teraz pokazuje tylko 40KB wolnego miejsca. Co mogę zrobić co wywalić? Podpowiesz?
I napisz proszę jeszcze jak sprawdzić lub gdzie ustawić, żeby dyski montowały się przed włączeniem transmission

19

Odp: Transmission - niestabilność, errory, błędy w ściągniętych danych

Uruchom bez dysku i zobacz czy masz katalog /mnt/sda1/ Jeżeli tak to go wywal.

Patrz np. http://eko.one.pl/?p=openwrt-skrypty#ur … aniunonika

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.