No i jeszcze log z uruchomienia co oczywiście pominąłem.
U-Boot 2010.06 (Oct 24 2013 - 15:36:07)
NAND: Special Nand id table Version 1.35
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
0 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
16384 KiB hi_sfc at 0:0 is now current device
Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.0.8
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2596884 Bytes = 2.5 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.8 (root@wang) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #1 Thu Oct 24 11:05:48 CST 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: hi3518
Memory policy: ECC disabled, Data cache writeback
AXI bus clock 220000000.
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: mem=128M console=ttyAMA0,115200 root=/dev/mtdblock1 rootfstype=jffs2 mtdparts=hi_sfc:3M(boot),13M(rootfs)
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125032k/125032k available, 6040k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xfe000000 ( 856 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0025000 ( 116 kB)
.text : 0xc0025000 - 0xc0490000 (4524 kB)
.data : 0xc0490000 - 0xc04afce0 ( 128 kB)
.bss : 0xc04afd04 - 0xc04c3500 ( 78 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:32 nr_irqs:32 32
sched_clock: 32 bits at 110MHz, resolution 9ns, wraps every 39045ms
Console: colour dummy device 80x30
Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.16)
msgmni has been set to 244
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
Spi id table Version 1.22
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
SPI FLASH start_up_mode is 3 Bytes
Spi(cs1):
Block:64KB
Chip:16MB
Name:"MX25L128XX"
spi size: 0x16777216
chip num: 1
2 cmdlinepart partitions found on MTD device hi_sfc
Creating 2 MTD partitions on "hi_sfc":
0x000000000000-0x000000300000 : "boot"
0x000000300000-0x000001000000 : "rootfs"
Fixed MDIO Bus: probed
himii: probed
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt73usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
mousedev: PS/2 mouse device common for all mice
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
registered taskstats version 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
▒VFS: Mounted root (jffs2 filesystem) on device 31:1.
Freeing init memory: 116K
[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
udevd (449): /proc/449/oom_adj is deprecated, please use /proc/449/oom_score_adj instead.
[RCS]: /etc/init.d/S80network
/etc/init.d/rcS: line 22: /usr/sbin/smtpclient: not found
start ------------ Ver(2013.03.16)
chmod: /usr/fx256: No such file or directory
mkdir: can't create directory '/main': File exists
fx256
rmmod: can't unload 'himci': unknown symbol in module, or unknown parameter
rmmod: can't unload 'sd_mmc_sdio': unknown symbol in module, or unknown parameter
Can't find fx256-bak.tar !
can't find /usr/fx256-upbk.tar !
/bin/sh: /usr/hhRestLog: not found
-------start is hi3518 -------
hi3518_io driver init start
alarmOutType gpio init 0, GpioFunctionType = 0
hi3518_io driver init successful(2012.12.22)!
-------start is hi3518 -------
count == 2(/main/fx256)
main -- start1!
mkdir: can't create directory '/fx': File exists
Read DeviceCfg = [0x00000000]
memsize 262144 logMode 0 logPri 3 FileNum 5
umount: can't umount /syslog/: Invalid argument
software 2.0.23.13 compile time is Aug 5 2014 17:11:17
SS_FLASH_ReadDeviceCfgUboot success 1256
cputype=3516c
byCPUTYPE=3
dwDeviceType=1
bySensorType3=32
st_size=192032
sttmpelen=100816
return
sysconfiglen=192032
.inita.size Width=1920
.inita.size Height=1080
*****************copy read time
************func = SS_FLASH_ReadBakTime, pTime->hour = 17, pTime->minute = 24
/etc/passwd: Resource temporarily unavailable
an error occurred updating the password file.
An error occurred updating the password file.
HiCpuType=3
Hisilicon Media Memory Zone Manager
hi3518_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Hisilicon UMAP device driver interface: v3.00
pa:88000000, va:c8b00000
load sys.ko for Hi3518...OK!
ISP Mod init!
load vpss.ko ....OK!
rmmod: can't unload 'himci': unknown symbol in module, or unknown parameter
rmmod: can't unload 'mmc_block': unknown symbol in module, or unknown parameter
rmmod: can't unload 'mmc_core': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_adec': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_aenc': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_ao': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_ai': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_sio': unknown symbol in module, or unknown parameter
rmmod: can't unload 'acodec': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hidmac': unknown symbol in module, or unknown parameter
rmmod: can't unload 'pwm': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_ive': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_vda': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_region': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_rc': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_jpege': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_h264e': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_chnl': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_group': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_venc': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hifb': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_vou': unknown symbol in module, or unknown parameter
unload vpss.ko ....OK!
ISP Mod Exit!
rmmod: can't unload 'hi3518_viu': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_dsu': unknown symbol in module, or unknown parameter
rmmod: can't unload 'hi3518_tde': unknown symbol in module, or unknown parameter
MMZ force removed: PHYS(0x88000000, 0x8EFFFFFF), GFP=0, nBYTES=114688KB, NAME="anonymous"
mkdir: can't create directory '/dev/misc': File exists
Hisilicon Media Memory Zone Manager
Hisilicon UMAP device driver interface: v3.00
pa:88000000, va:c8c00000
load sys.ko for Hi3518...OK!
load viu.ko for Hi3518...OK!
ISP Mod init!
load vpss.ko ....OK!
load vou.ko ....OK!
load venc.ko for Hi3518...OK!
load group.ko for Hi3518...OK!
load chnl.ko for Hi3518...OK!
load h264e.ko for Hi3518...OK!
load jpege.ko for Hi3518...OK!
load rc.ko for Hi3518...OK!
load region.ko ....OK!
load vda.ko ....OK!
hi_i2c init is ok!
hi3516_io driver remove successful(2011.10.28)!
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f000c: 0x00000000 --> 0x00000001
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0010: 0x00000000 --> 0x00000001
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x200f0014: 0x00000000 --> 0x00000001
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20030030: 0x00000000 --> 0x00000006
[END]
Kernel: ssp initial ok!
hi3518_io driver init start
alarmOutType gpio init 0, GpioFunctionType = 1
hi3518_io driver init successful(2012.12.22)!
hi3518_io driver init start
alarmOutType gpio init 0
hi3518_io driver init successful(2012.12.22)!
Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nowayout= 0, nodeamon= 0)
ln: /dev/misc/io_dev: File exists
acodec inited!
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
NET: Registered protocol family 24
PPP MPPE Compression module registered
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110150: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110154: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110158: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011015C: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110160: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110164: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110168: 0x00000004 --> 0x00010206
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011016C: 0x00000004 --> 0x00010206
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110170: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110174: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110178: 0x00000004 --> 0x00003FF6
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011017C: 0x00000004 --> 0x00003FF3
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110180: 0x00000004 --> 0x00003FF4
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110184: 0x00000004 --> 0x00010C82
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110188: 0x00000004 --> 0x00010101
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2011018c: 0x00000004 --> 0x00010100
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20110100: 0x0000000F --> 0x00000067
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20050038: 0x00000000 --> 0x00000003
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20580010: 0x00000000 --> 0x00000003
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x205cce00: 0x00000000 --> 0x08003003
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20600314: 0x00FFFF66 --> 0x01640000
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x2061002c: 0x00888010 --> 0x00444010
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x206200A4: 0x00000007 --> 0x00000003
[END]
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x206600A4: 0x00000000 --> 0x00000003
[END]
(0)str=0------------------------
hc0104 driver init successful(2012.1.1)!
hc0104_ioctl cmd: 1 data: 0
hc0104_ioctl sta=0
@@@@@@@@@@@@@@@@@@L0 SysInit OK!
ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.16.1) started
Sending discover...
PHY: himii:01 - Link is Up - 100/Full
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sending discover...
Sending select for 192.168.8.131...
Lease of 192.168.8.131 obtained, lease time 43200
deleting routers
route: SIOCDELRT: No such process
adding dns 192.168.8.1
route: SIOCADDRT: File exists
mkdir: can't create directory '/wifi': File exists
rtusb init rtusbSTA --->
usbcore: registered new interface driver rtusbSTA
ifconfig: SIOCGIFFLAGS: No such device
21 SysConfig.stNetBaseWifi.byAuthType = 2 0 2
/wifi/wpa_supplicant -Dwext -ira0 -c/etc/wpa_supplicant.conf &
udhcpc: SIOCGIFINDEX: No such device
Could not read interface ra0 flags: No such device
Failed to initialize driver interface
ifconfig: SIOCSIFADDR: No such device
supportHH = 1
@@@@@@@@@@@@@@@@hc0104_ioctl cmd: 1 data: 0
@@ SysInit OK!
hc0104_ioctl sta=0
@@@@@@@@@@@@@@@@@@L0 Check Data OK!
net lib Make On Jun 30 2014 10:40:10
g_server_info.hMultiListenSock=0
baseip=192.168.8.131
wifiip=192.168.1.160
@@@@@@@@@@@@@@@@hc0104_ioctl cmd: 1 data: 0
@@ SysInit OK!
hc0104_ioctl sta=0
@@@@@@@@@@@@@@@@@@L0 Check Data OK!
rm: /tmp/aaa: is a directory
rm: /tmp/bbb: is a directory
*******************fx256 init
Creat queue id:0
queue id:0
mkdir: can't create directory '/onvif': File exists
cdp uses obsolete (PF_INET,SOCK_PACKET)
device_service start...
device_service end...
3702 discovery Make On May 29 2014 19:40:06
send 3702 hello msg start...
onvif cgi Make On Jun 16 2014 22:14:19
.3702.hello...usDataLen=1480......
.3702.hello...ret=1480......
send 3702 hello msg end...
SensorLib Make On Jun 20 2014 17:56:35
LIBSENSOR Sensor TYPE is SENSOR_CMOS_1080P_IMX122
Socket connection successful: master socket = 4
-------Sony IMX122 Sensor Initial OK!-------
...size Width=1920
...size Height=1080
AnvLib Make On Jun 20 2014 17:56:17
.....nWidth=320.....nHeight=240....
LIBANV mm = 0 (0)mask handle = 16777215 16777215 16777215 16777215
******************mac
set_filter_ctrl == 1
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20050078: 0x1E1EC001 --> 0x0909C001
[END]
gain_mic = 31
LIBANV #########Ai Enalble Dev 0 Chn 0 Ok.
LIBANV #########Ai Enalble Dev 0 Chn 1 Ok.
set_filter_ctrl == 0
set_filter_ctrl == 1
******************mac
*** Board tools : ver0.0.1_20120501 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20050078: 0x0E0EC001 --> 0x0909C001
[END]
gain_mic = 31
@@@@@@@@@@@@@@@@hc0104_ioctl cmd: 1 data: 0
@@ SysInit OK!
hc0104_ioctl sta=0
@@@@@@@@@@@@@@@@@@L0 Check Data OK!
=========RTSPlib version is Jun 30 2014 14:10:55
RTSPLib Make On Jun 30 2014 14:10:55
startRtspServer rtspPort=554,bUserAuth=0,bPassive=1,mtu=1460,maxChn=1
startRtspServer begin line = 4545
********* CreatRtspServer begin socket=0 port=554
********* CreatRtspServer result socket=55 port=554
********* CreatRtspServer success socket=55 port=554
setAvInfor begin line = 4502
RTSP setAvInfor === nCh=0,bMain=0,videoPt=96,audioPt=97
setAvInfor line = 4514
setAvInfor end line = 4522
setAvInfor begin line = 4502
RTSP setAvInfor === nCh=0,bMain=1,videoPt=96,audioPt=97
setAvInfor line = 4514
setAvInfor end line = 4522
rtsp_unicast_multicast nRtspSever=0,bMutlicast=1,szMulticastIP=239.0.0.0,nMainVideoPort=5010,nMainAudioPort=5012,nViceVideoPort=5020,nViceAudioPort=5022,nRes=0
rtsp_unicast_multicast begin line = 4661
rtsp_unicast_multicast end line = 4680
gb28181 start...
szdec = eth0, pott == 18600, cGateway = 192.168.8.1
[08:34:05.570254] [udpserver] 7398bb50 started
[08:34:05.574558] [gsclient_start] 74222b50 started
[08:34:05.575045] [gtserver_start] 74a2eb50 started
[08:34:05.575520] [gtdiscovery_create] 75287b50 started
[08:34:05.576026] [upnp_func] 75ab9b50 started
[08:34:05.578857] [startMiniServer] 763a0b50 started
hk mobile no run
HiMFS_Init ---- start
mkdir: can't create directory '/disk/k:': No such file or directory
mkdir: can't create directory '/disk/l:': No such file or directory
HiMFS_Init ---- end
@@@@@@@@@@@@@@@@hc0104_ioctl cmd: 1 data: 0
@@ SysInit OK!
hc0104_ioctl sta=0
HiDEV_DiskMonitorThread -------------- Start
@@@@@@@@@@@@@@@@hc0104_ioctl cmd: 1 data: 0
@@ SysInit OK!
hc0104_ioctl sta=0
@@@@@@@@@@@@@@@@@@L0 Check Data OK!
**********u32QpDelta = 0
enSuperFrmMode = 0, u32MaxIprop = 4
LIBANV ######### SS_Hi3516c_VencSetChnAttr HI_MPI_VENC_SetChnAttr ok 0x0
**********u32QpDelta = 0
enSuperFrmMode = 0, u32MaxIprop = 4
LIBANV ######### SS_Hi3516c_VencSetChnAttr HI_MPI_VENC_SetChnAttr ok 0x0
LIBANV ######### SS_Hi3516c_VencSetChnAttr HI_MPI_VENC_SetChnAttr ok 0x0
@@@@@@@@@@@@@@@@@@L0 Check Data OK!
[08:34:09.723119] [SCTManager] 9583bb50 started
mkdir: can't create directory '/mempic': File exists
set_filter_ctrl == 0
bkp->tm_year=117
currp->tm_year=117
.InfraredDetectMode..cai zhuan hei .
struViScene.byphotoresistorLevel = 1
mkdir: can't create directory '/memrec': File exists
uVencErrorCount = 1
smtpclient ----------- v1.2(2011-12-31)
smtpclient key = -1 1644232972 id = 131076 163845(/unix/smtpclient)
. Życzę sukcesu.
