551

Odp: Sagemcom 2704 a OpenWRT

Witam

  Dostałem w swoje ręce    router z tytułu   i jak zwykle  grzebię  przy gpio.   Niestety nie wiem jak tym sterować  mam  coś takiego:

/sys/devices/ubus@10000000/10000084.gpio-controller/gpio/gpiochip480#

Jak tym sterować?   Info z poradnika nie działa  a może   nie wiem jak.

552

Odp: Sagemcom 2704 a OpenWRT

Wejdź do /sys/class/gpio

Bo za daleko jesteś. cat /sys/kernel/debug/gpio powie ile masz gpio i w jakim zakresie numeracji dostępnych.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

553

Odp: Sagemcom 2704 a OpenWRT

Dzięki oto chodziło

554

Odp: Sagemcom 2704 a OpenWRT

Ogarnięty szałem lutowania postanowiłem zmienić RAM w tym ruterze i udało się zwiększyć ją dwukrotnie:

HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 5.38.7 for BCM96328 (32bit,SP,BE)
Build Date: Fri Aug 10 17:44:02 CST 2012 (liruicong@SZ01007.DONGGUAN.CN)
Copyright (C) 2005-2010 SAGEM Corporation.

HS Serial flash device: name S25FL064, id 0x0116 size 8192KB
Total Flash size: 8192K with 128 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-5)                    : F@ST2704V2
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 7c:03:d8:96:f0:c2
PSI Size (1-64) KBytes            : 40
Enable Backup PSI [0|1]           : 0
System Log Size (0-256) KBytes    : 0
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8010000) ...
Code Address: 0x80A00000, Entry Address: 0x80a00000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80a00000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80a00000
[    0.000000] Linux version 3.18.23 (cezary@eko.one.pl) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #5 Sat Jan 2 21:04:18 CET 2016
[    0.000000] Detected Broadcom 0x6328 CPU revision b0
[    0.000000] CPU frequency is 320 MHz
[    0.000000] 128MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 53.46.51-56.46-55
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a075 (Broadcom BMIPS4350)
[    0.000000] board: board name: F@ST2704V2
[    0.000000] MIPS: machine is Sagem F@ST2704V2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 124692K/131072K available (2815K kernel code, 138K rwdata, 664K rodata, 1304K init, 192K bss, 6380K reserved)
[    0.000000] NR_IRQS:256
[    0.000000] Calibrating delay loop... 319.74 BogoMIPS (lpj=639488)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060000] NET: Registered protocol family 16
[    0.300000] registering PCI controller with io_map_base unset
[    0.324000] PCI host bridge to bus 0000:00
[    0.328000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
[    0.332000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.336000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.340000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.344000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[    0.348000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[    0.352000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.356000] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
[    0.360000] Switched to clocksource MIPS
[    0.364000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    0.372000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[    0.376000] bcma: bus0: Found chip with id 43225, rev 0x01 and package 0x0A
[    0.384000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[    0.392000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[    0.404000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[    0.536000] bcma: bus0: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[    0.544000] bcma: bus0: Using fallback SPROM failed (err -2)
[    0.548000] bcma: bus0: No SPROM available
[    0.564000] bcma: bus0: Bus registered
[    0.568000] NET: Registered protocol family 2
[    0.576000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.584000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.588000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.596000] TCP: reno registered
[    0.600000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.604000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.612000] NET: Registered protocol family 1
[    0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.628000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.636000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.644000] msgmni has been set to 243
[    0.652000] io scheduler noop registered
[    0.656000] io scheduler deadline registered (default)
ú[    0.672000] console [ttyS0] enabled MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
[    0.672000] console [ttyS0] enabled
[    0.680000] bootconsole [early0] disabled
[    0.680000] bootconsole [early0] disabled
[    0.692000] m25p80 spi1.0: found s25sl064p, expected m25p80
[    0.696000] m25p80 spi1.0: s25sl064p (8192 Kbytes)
[    0.704000] bcm63xxpart: CFE boot tag found with version 6 and board type F@ST2704V2
[    0.712000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.716000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 136469
[    0.724000] bcm63xxpart: Partition 2 is rootfs offset 146569 and length 6a9a97
[    0.732000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000
[    0.740000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000
[    0.748000] 5 bcm63xxpart partitions found on MTD device spi1.0
[    0.752000] Creating 5 MTD partitions on "spi1.0":
[    0.756000] 0x000000000000-0x000000010000 : "CFE"
[    0.764000] 0x000000010100-0x000000146569 : "kernel"
[    0.772000] 0x000000146569-0x0000007f0000 : "rootfs"
[    0.776000] mtd: device 2 (rootfs) set to be root filesystem
[    0.792000] 1 squashfs-split partitions found on MTD device rootfs
[    0.800000] 0x0000003c0000-0x0000007f0000 : "rootfs_data"
[    0.808000] 0x0000007f0000-0x000000800000 : "nvram"
[    0.816000] 0x000000010000-0x0000007f0000 : "linux"
[    0.860000] b53_common: found switch: BCM63xx, rev 0
[    0.864000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.876000] TCP: cubic registered
[    0.876000] NET: Registered protocol family 17
[    0.884000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.896000] Bridge firewalling registered
[    0.900000] 8021q: 802.1Q VLAN Support v1.8
[    0.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.944000] Freeing unused kernel memory: 1304K (8039a000 - 804e0000)
[    2.724000] init: Console is alive
[    2.728000] init: - watchdog -
[    3.512000] random: nonblocking pool is initialized
[    5.432000] usbcore: registered new interface driver usbfs
[    5.436000] usbcore: registered new interface driver hub
[    5.444000] usbcore: registered new device driver usb
[    5.540000] SCSI subsystem initialized
[    5.560000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.572000] ehci-platform: EHCI generic platform driver
[    5.680000] ehci-platform ehci-platform: EHCI Host Controller
[    5.684000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.692000] ehci-platform ehci-platform: irq 50, io mem 0xb0002500
[    5.712000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[    5.720000] hub 1-0:1.0: USB hub found
[    5.724000] hub 1-0:1.0: 1 port detected
[    5.736000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.744000] ohci-platform: OHCI generic platform driver
[    5.752000] ohci-platform ohci-platform: Generic Platform OHCI controller
[    5.756000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    5.768000] ohci-platform ohci-platform: irq 49, io mem 0xb0002600
[    5.832000] hub 2-0:1.0: USB hub found
[    5.836000] hub 2-0:1.0: 1 port detected
[    5.852000] usbcore: registered new interface driver usb-storage
[    6.772000] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   11.292000] mount_root: loading kmods from internal overlay
[   11.676000] jffs2: notice: (268) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   11.696000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   11.716000] block: extroot: not configured
[   11.768000] jffs2: notice: (265) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   11.952000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   11.972000] block: extroot: not configured
[   11.980000] mount_root: switching to jffs2 overlay
[   12.044000] procd: - early -
[   12.048000] procd: - watchdog -
[   12.988000] procd: - ubus -
[   14.000000] procd: - init -
Please press Enter to activate this console.
[   15.936000] NET: Registered protocol family 10
[   15.976000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   16.008000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   16.016000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   16.028000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.056000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[   16.136000] xt_time: kernel timezone is -0000
[   16.200000] cfg80211: Calling CRDA to update world regulatory domain
[   16.256000] cfg80211: World regulatory domain updated:
[   16.260000] cfg80211:  DFS Master region: unset
[   16.264000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   16.276000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   16.284000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   16.292000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   16.300000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   16.308000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   16.316000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   16.324000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   16.332000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   16.460000] PPP generic driver version 2.4.2
[   16.468000] NET: Registered protocol family 24
[   16.528000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
[   16.536000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[   16.540000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11, Version 0
[   16.548000] Broadcom 43xx driver loaded [ Features: PNL ]
[   28.160000] device eth0.1 entered promiscuous mode
[   28.168000] device eth0 entered promiscuous mode
[   28.180000] br-lan: port 1(eth0.1) entered forwarding state
[   28.184000] br-lan: port 1(eth0.1) entered forwarding state
[   30.188000] br-lan: port 1(eth0.1) entered forwarding state



BusyBox v1.23.2 (2015-09-10 18:36:24 CEST) built-in shell (ash)


        _______                     ________        __
       |       |.-----.-----.-----.|  |  |  |.----.|  |_
       |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
       |_______||   __|_____|__|__||________||__|  |____|
                |__| W I R E L E S S   F R E E D O M

 ----------------------------------------------------------------
 |                                                              |
 | OpenWrt Chaos Calmer 15.05 (r48023)                          |
 | Build time: 2016-01-02 21:01 CET                             |
 |                                                              |
 | Cezary Jackiewicz (obsy), http://eko.one.pl                  |
 |                                                              |
 ----------------------------------------------------------------
 | Machine: Sagem F@ST2704V2                                    |
 | Uptime: 0d, 00:06:31                                         |
 | Load: 0.08 0.11 0.06                                         |
 | Flash: total: 4.2MB, free: 3.9MB, used: 7%                   |
 | Memory: total: 123.0MB, free: 112.9MB, used: 8%              |
 | WAN:                                                         |
 | LAN: 192.168.1.1                                             |
 ----------------------------------------------------------------
root@OpenWrt:/# free
             total         used         free       shared      buffers
Mem:        125996        18836       107160           64         1988
-/+ buffers:              16848       109148
Swap:            0            0            0
root@OpenWrt:/#

Użyłem do tego celu kostki HY5PS1G1631C zdjętej z SO-DIMM o pojemności 512, ale nada się chyba każda o organizacji 64Mx16.
http://vpx.pl/i/2017/04/19/sagem.md.jpg
Oczywiste jest, że to raczej ciekawostka, ale ktoś może się pokusi o coś podobnego...
Może teraz domoticz będzie na tym działał stabilnie? Przy 64MiB stale się wysypywał. Sprawdzę niebawem.

555

Odp: Sagemcom 2704 a OpenWRT

Skąd brałeś   domoticz-a?   I działa na większym ramie?   Mam   taki router i kostkę   to może i sobie bym  wymienił...

556

Odp: Sagemcom 2704 a OpenWRT

Stąd.
Działa bardzo ładnie.

557

Odp: Sagemcom 2704 a OpenWRT

Dzięki  ale to muszę chyba kompilować? Bo ipk nie widzę.

558 (edytowany przez kurwicycek 2018-03-30 12:35:50)

Odp: Sagemcom 2704 a OpenWRT

Zgadza się.
Możesz też użyć mojej kompilacji.

559

Odp: Sagemcom 2704 a OpenWRT

Jaki jest koszt samego ramu i jego późniejszej instalacji w routerze.
Da się to polutować zwykłą lutownicą ?

560

Odp: Sagemcom 2704 a OpenWRT

Da się - zwykłą lutownicą na gorące powietrze smile. W sumie to ja i opalarką dał bym radę, ale mam spore doświadczenie wink.
Koszt to $0.99 na AliExpress, albo wylutować z kości SO-DIMM, które są po cenie złomu.

561

Odp: Sagemcom 2704 a OpenWRT

kurwicycek napisał/a:

Stąd.
Działa bardzo ładnie.

Jeszcze pomęczę  (sorry)  a ile  wynosi uptime  domoticz-a/całego  routera? Na  forum  jak czytałem to ludzie się cieszą jak tydzień działa bez wywalenia!!  Kiepsko to wygląda   ,  piszą  oczywiście o rp-i ale   może na  open jest lepiej?

562

Odp: Sagemcom 2704 a OpenWRT

Nie testowałem tak długo tego sprzętu, bo to tylko tak dla zabawy. Mam terminal Wyse S10 z CC i tam działa stabilnie kilka miesięcy. Na OpenWrt miałem problemy jedynie gdy brakowało ramu.

563

Odp: Sagemcom 2704 a OpenWRT

kurwicycek napisał/a:

Mam terminal Wyse S10 z CC i tam działa stabilnie kilka miesięcy. Na OpenWrt miałem problemy jedynie gdy brakowało ramu.

Przeglądając tutaj posty okazuje się że jesteś specjalistą od   Thin Client i gpio. Mam więc pytanie co kupić aby  działał  dobrze działał open oraz było sporo działających   gpio?    Przydało by się  też działające i2c.

564

Odp: Sagemcom 2704 a OpenWRT

Nie jestem specjalistą tylko lamusem smile.
W rzeczonym terminalu jest faktycznie dużo wolnych GPIO, ale do każdego trzeba się dobierać bezpośrednio do CPU z drugiej strony PCB. Wprawa w lutowaniu niezbędna.
Tobie polecam zainteresować się tym.

565

Odp: Sagemcom 2704 a OpenWRT

Takich modułów jest trochę. Omega 1 i 2, domino od gl-inet, popularny ostatnio MediaTek LinkIt Smart 7688, nie mówiąc już od zwykłym RPi. Ale to OT.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

566

Odp: Sagemcom 2704 a OpenWRT

Pytanie do Cezarego,
czy można liczyć na Twoje obrazy LEDE na ten router? O Gargoyle nawet nie marzę...

567

Odp: Sagemcom 2704 a OpenWRT

Na chwilę obecną nie przewiduje takich obrazów.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

568

Odp: Sagemcom 2704 a OpenWRT

Czy jest nowszy firmware niż luci-15.05-brcm63xx-generic-F@ST2704V2-squashfs-cfe? bo nie natrafiłem

569 (edytowany przez mar_w 2017-09-26 22:50:51)

Odp: Sagemcom 2704 a OpenWRT

Na Lede-project jest snapshot:
http://downloads.lede-project.org/snaps … fs-cfe.bin

lub stable:
http://downloads.lede-project.org/relea … fs-cfe.bin

* WNDR 4300v2 * ||  * Xiaomi Miwifi Mini * || Netgear R6220 *
* DVBT2 - T230C *

570

Odp: Sagemcom 2704 a OpenWRT

Bo openwrt nie jest już rozwijane...

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

571

Odp: Sagemcom 2704 a OpenWRT

Witam i mam pytanie: ponieważ mam ten router jako rezerwowy, bo też kiedyś od Orange kupiłem to czy gdybym wgrał ten soft lede-17.01.2-brcm63xx-generic-FAST2704V2-squashfs-cfe, to czy internet przez ADSL2+ by działał?

I czy wystarczy go wgrać z poziomu softu orange, czy trzeba przez złącze szeregowe?

572

Odp: Sagemcom 2704 a OpenWRT

Nie, dsl na tym urządzeniu nie działa. Nie ma drivera do broadcoma.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

573

Odp: Sagemcom 2704 a OpenWRT

Witam
Z góry przepraszam za braki w mojej wiedzy nt. modowania routerów ale chcę to zmienić smile

Mogę kupić to urządzenie i mam kilka pytań.
1. Gdzie pobrać obraz Luci OpenWRT Cezarego?
2. Jest tam GUI, takie dla zwykłego użytkownika (jak w Gargoyle)?
3. Wgrywać w zakładce aktualizacji oprogramowania?
4. To WiFi działa czy nie? Tryb b/g to nie problem.
5. Czy da radę zrobić repeater?

Maska podsieci będzie 255.255.248.0, piszę bo jeden repeater nie dał rady big_smile

574

Odp: Sagemcom 2704 a OpenWRT

1. Stare: http://dl.eko.one.pl/luci/chaos_calmer/brcm63xx/
2. Skoro pytasz się o luci to tak, jest... luci
3. tak
4. tylko b/g.
5. Jeżeli musisz, choć to nie jest polecany tryb pracy.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

575 (edytowany przez 9tysiecy 2018-02-01 12:15:56)

Odp: Sagemcom 2704 a OpenWRT

Mam już router, wgrałem to OpenWRT i jak teraz ustawić repeater? Znalazłem poradnik
http://eko.one.pl/?p=openwrt-sta#mostbezprzewodowy
Ale nie mam pojęcia jak to ustawić. Pomóż big_smile