26

Odp: ZyXEL P-2812HNU czy Netgear 3700?

geos napisał/a:

wydałem polecenie:

root@OpenWrt:/# ubidetach -p /dev/mtd4

i zonk:

ubidetach: error!: cannot detach "/dev/mtd4"
           error 19 (No such device)

porównałem wpisy na wiki z tymi podanymi przez Ciebie.
http://wiki.openwrt.org/toh/zyxel/p2812hnu-f3
https://www.dropbox.com/sh/9aup68dv6oq5 … t.txt?dl=0

i jest różnica. na wiki widnieje /dev/mtd4 podczas gdy w pliku z dropboxa /dev/mtd5. edycja: zgłosiłem na forum openwrt i już poprawili.

No to namieszaliśmy... Okazuje się, że dla plików z dropboxa powinno używać się tam zamieszczonych instrukcji.
Natomiast instukcja na wiki była OK. - pod warunkiem stosowania plików z github: https://github.com/ScApi/P2812HNUFx-Pre-Build
Więcej szczegółów tutaj: https://forum.openwrt.org/viewtopic.php … 52#p284552

27 (edytowany przez geos 2015-07-25 19:51:50)

Odp: ZyXEL P-2812HNU czy Netgear 3700?

tak, widziałem. dobrze, że Scapi czuwał, od razu się wyjaśniło dlaczego było trochę inaczej. zastanawiam się, czy Scapi nie jest Polakiem.

28

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Też tak myślę - "sylwek@WRT" brzmi znajomo wink

29

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Witajcie!
Czy ma ktos moze dokladne zdjecie P-2812HNU-F1?
Interesuja mnie okolice ukladu VRX208 - chcialbym porownac
wersje F1 i F3.

Pozdrawiam,
Karol

30

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Domyślam się, że chcesz przerobić P-2812HNU-F3 aby pracował na linii adsl z annex A?
Wnioskuję tak po Twoim wpisie na forum openwrt.
Powodzenia!

http://s5.ifotos.pl/mini/WP2017020_awhrnhp.jpg
http://s5.ifotos.pl/mini/WP2017020_awhrnhw.jpg

31 (edytowany przez bizongod 2017-02-15 22:12:04)

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Dzieki za zdjecia.

Tak, stanawiam sie na ile jest to wykonalne.
Z tego co widze, to layout jest bardzo zblizony.
Tu taka tabelka z porownaniem oczywistych roznic w
wartosciach elementow:

Element   F1(Annex A)     F3(Annex B)
R135        24.9R              10R
T6            UTB01802S-A  UTB01930S-A
C110        27nF                22nF
C113        ??                    brak
C115        ??                    brak
R140        1k                    brak
R141        1k                    brak

Transformatory to rzecz oczywista, jeden ma
1.4mH (Annex A), drugi 270uH (Annex B).
Kondensatory C110 tez prosta sprawa.
Wieksze wartosci przenosza nizsze czestotliwosci (Annex A).

Jest jeszcze roznica w okolicach CP18-CP22, ale jak sadze sa
to kondensatory odsprzegajace zasilanie, wiec bez wplywu na
Annex.

Gdzies na forach widzialem, ze przy zamianie Annexu przez sam
firmware krzyczy ze jest niewlasciwy.

Jestem ciekaw, czy rozpoznaje tylko po ww elementach, czy
jest cos jeszcze.

Wiesz moze, czy nie ma problemu z uruchomieniem firmware od
Annex B na sprzecie z Annex A? Bo teoretycznie wartosci
elementow powinny na to pozwolic.

Moze to ktores elementy po drugiej stronie PCB?

Nie wiem na ile dobrze zrozumialem, ale ponoc jakies Fritz'e
w wersji international z VR9 moga pracowac zarowno z Annexem A i B.

Zalaczam zdjecia wersji F3, tak dla porownania smile

http://s2.ifotos.pl/mini/DSC003092_awrrsna.jpg
http://s10.ifotos.pl/mini/DSC00310J_awrrsep.jpg
http://s5.ifotos.pl/mini/DSC003212_awrrsqx.jpg

Jak masz, to wrzuc jeszcze zdjecie PCB od tylu.

Pozdrawiam,
Karol

32

Odp: ZyXEL P-2812HNU czy Netgear 3700?

bizongod napisał/a:

Gdzies na forach widzialem, ze przy zamianie Annexu przez sam
firmware krzyczy ze jest niewlasciwy.

Tak, to prawda: http://eko.one.pl/forum/viewtopic.php?p … 77#p150577

bizongod napisał/a:

Jestem ciekaw, czy rozpoznaje tylko po ww elementach, czy
jest cos jeszcze.

Tego nie wiem

bizongod napisał/a:

Wiesz moze, czy nie ma problemu z uruchomieniem firmware od
Annex B na sprzecie z Annex A? Bo teoretycznie wartosci
elementow powinny na to pozwolić.

Odpowiem tak, na swojej linii vdsl2 z Orange przez większość czasu nieświadomie używałem P-2812HU-F3 z firmware Annexem A.
Dopiero później zmieniłem firmware na właściwy (z Annex B).

bizongod napisał/a:

Moze to ktores elementy po drugiej stronie PCB?

Postaram się w wolnej chwili zrobić fotkę

bizongod napisał/a:

Nie wiem na ile dobrze zrozumialem, ale ponoc jakies Fritz'e
w wersji international z VR9 moga pracowac zarowno z Annexem A i B.

Całkiem możliwe, mam również Asusa DSL-AC68U i podobno też działa na liniach z A i B:

ASUS DSL-AC68U Firmware version 3.0.0.4.380_4291 (This product supports both Annex A and Annex B)

33 (edytowany przez bizongod 2017-02-08 08:30:52)

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Scotch napisał/a:

Całkiem możliwe, mam również Asusa DSL-AC68U i podobno też działa na liniach z A i B:

ASUS DSL-AC68U Firmware version 3.0.0.4.380_4291 (This product supports both Annex A and Annex B)

No tu jest nieco inna sytuacja. Jest on z tego co widze na MT7510.

Jakies schematy modemow/routerow xDSL mozna znalezc na https://fcc.io/
i widac na nich, ze front-end dla xDSL mocno sie roznia w zaleznosci czy to Broadcom czy inny
producent scalaka.

Tu kilka przykladow z wariantami dla Annex'ow:
https://fccid.io/pdf.php?id=717823
https://fccid.io/pdf.php?id=906154
https://fccid.io/pdf.php?id=412521
https://fccid.io/pdf.php?id=1440662

A tu rozne inne modemy/routery xDSL, raczej leciwe:
https://fccid.io/pdf.php?id=251981
https://fccid.io/pdf.php?id=1317158
https://fccid.io/pdf.php?id=767666
https://fccid.io/pdf.php?id=667328
https://fccid.io/pdf.php?id=2060932
https://fccid.io/pdf.php?id=78599
https://fccid.io/pdf.php?id=1526961

Pozdrawiam,
Karol

34

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Poniżej zdjęcia płytki od tyłu.
Pozdrawiam

http://s5.ifotos.pl/mini/1jpg_awxehpw.jpghttp://s5.ifotos.pl/mini/2jpg_awxehhe.jpg
http://s10.ifotos.pl/mini/3jpg_awxehhq.jpg

35

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Dzieki za zdjecia!

Zrobilem mala analize, na zdjeciach widac wyniki :

Annex A, bottom
http://s5.ifotos.pl/mini/annAbot3j_aweprqq.jpg

Annex B, bottom
http://s5.ifotos.pl/mini/annBbotDS_awepxpr.jpg

Annex A, top:
http://s2.ifotos.pl/mini/annAtopWP_awepxpe.jpg

Annex B, top:
http://s5.ifotos.pl/mini/annBtopDS_awepxps.jpg

Gratis,  HH5A, Annex A:
http://s5.ifotos.pl/mini/annAHH520_awepxpq.jpg

Wyglada na to,  ze VRX208 rozpoznaje sprzet annexu po
rezystorach R47-R109, R110-R49, R111-R50.

Roznica jest w obsadzeniu rezystorow (R143,R144)/(R143,R145) ,
R126, R116 i (R117,R118). Rezystory mniejsze, w obudowie 0402 to
prawdopodobnie 0Ohm. Oczywiscie sa tez roznice o ktorych wczesniej
pisalem wink

Bardzo przydaly by sie dokladne zdjecia Fritz'a 7360 w wersji
international. Ponoc obsluguje oba annexy jednoczesnie.
https://en.avm.de/products/fritzbox/fri … ical-data/

Moze ktos mialby takie zdjecia? smile

Pozdrawiam

36

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Witam kolegów
Czy udało się komuś uruchomić Adsl Annexu A na F3??
Dopadłem dzisiaj ten router, uruchomiłem już Lede i przydałoby się aby ADSL też ruszyło bo światłowodu długo się nie doczekam i jakoś z tym orężem trzeba żyć smile
Nie zależy mi na multianexie wystarczy sam A smile

37

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Witam,
Próbuję wgrać OpenWrt wg instrukcji ale po wgraniu uboota wyskakuje:
Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   125 MHz
IO:    125 MHz
BUS:   125 MHz
BOOT:  UART
DRAM:  256 MiB
Flash: 8 MiB
NAND:  0 MiB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
P-2812HNU-Fx #

Czy w moim egzemplarzu udało mi się uwalić NAND ?
Czy idzie to naprawić ?

38

Odp: ZyXEL P-2812HNU czy Netgear 3700?

No to jest własnie uboot. Sam uboot. Teraz wgraj obraz.

PS. Chodzi o to że wyświetla NAND 0MB? Wgraj  openwrt-lantiq-p2812hnufx_nor-u-boot.img bo chyba cały czas z tego pierwszego (UART) jesteś zabootowany.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

39 (edytowany przez m-s-x 2018-03-01 09:46:55)

Odp: ZyXEL P-2812HNU czy Netgear 3700?

wgrałem tak
U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
P-2812HNU-Fx #

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
P-2812HNU-Fx # Ŕ

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  1

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
P-2812HNU-Fx #
ROM VER: 1.0.5
CFG 04
UART
********************************************************************************                                 ********************************************************************************                                 ********************************************************************************                                 *****************

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:06:52) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   125 MHz
IO:    125 MHz
BUS:   125 MHz
BOOT:  UART
DRAM:  256 MiB
Flash: 8 MiB
NAND:  128 MiB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
P-2812HNU-Fx # reset

ROM VER: 1.0.5
CFG 04
UART


U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
P-2812HNU-Fx # protect off all
Un-Protect Flash Bank # 1
................................................................................                                 ....................................................... done
P-2812HNU-Fx # erase all
Erase Flash Bank # 1
................................................................................                                 ....................................................... done
P-2812HNU-Fx # tftp 0x80700000 openwrt-lantiq-p2812hnufx_nor-u-boot.img
ltq_phy: addr 0, link 0, speed 10, duplex 0
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 1, speed 1000, duplex 1
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-p2812hnufx_nor-u-boot.img'.
Load address: 0x80700000
Loading: ######################
done
Bytes transferred = 318632 (4dca8 hex)
P-2812HNU-Fx # cp.b 0x80700000 0xb0000000 0x4dca8
Copy to Flash... done
P-2812HNU-Fx # reset˙

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
P-2812HNU-Fx # tftp 0x80800000 openwrt-lantiq-xrx200-P2812HNUF3-uImage
ltq_phy: addr 0, link 0, speed 10, duplex 0
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 1, speed 1000, duplex 1
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-xrx200-P2812HNUF3-uImage'.
Load address: 0x80800000
Loading: #################################################################
         ##################################
         5.5 MiB/s
done
Bytes transferred = 1448568 (161a78 hex)
P-2812HNU-Fx # nand erase.chip

NAND erase.chip: device 0 whole chip

nand0: MTD Erase failure: -5

nand0: MTD Erase failure: -5
....

nand0: MTD Erase failure: -5
Skipping bad block at  0x07700000

nand0: MTD Erase failure: -5
...
OK
P-2812HNU-Fx # nand write 0x80800000 0x0 0x200000

NAND write: device 0 offset 0x0, size 0x200000
nand_do_write_ops: Device is write protected
NAND write to offset 0 failed -5
0 bytes written: ERROR
P-2812HNU-Fx # <INTERRUPT>
P-2812HNU-Fx # tftpboot 0x80800000 openwrt-lantiq-xrx200-P2812HNUF3-uImage-initr                                 amfs
ltq_phy: addr 0, link 0, speed 10, duplex 0
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 1, speed 1000, duplex 1
ltq_phy: addr 5, link 0, speed 10, duplex 0
Using ltq-eth device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-lantiq-xrx200-P2812HNUF3-uImage-initramfs'.
Load address: 0x80800000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         ####################################################
done
Bytes transferred = 4568229 (45b4a5 hex)
P-2812HNU-Fx # bootm 0x80800000
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Created:      2014-12-21  14:26:46 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4568165 Bytes = 4.4 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.10.49 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Li                                 naro GCC 4.8-2014.04 r43483) ) #2 Sun Dec 21 15:26:23 CET 2014
[    0.000000] SoC: VR9 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019555 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF3 - ZyXEL P-2812HNU-F3
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32                                  bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                 es: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00047140
[    0.000000] Readback ErrCtl register=00047140
[    0.000000] Memory: 122360k/131072k available (3046k kernel code, 8712k reser                                 ved, 1031k data, 3208k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels:                                  28
[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.200000] bio: create slab <bio-0> at 0
[    0.204000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.208000] usbcore: registered new interface driver usbfs
[    0.212000] usbcore: registered new interface driver hub
[    0.216000] usbcore: registered new device driver usb
[    0.220000] PCI host bridge to bus 0000:00
[    0.224000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
[    0.228000] pci_bus 0000:00: root bus resource [io  0x1d800000-0x1d8fffff]
[    0.232000] pci_bus 0000:00: No busn resource found for root bus, will use [b                                 us 00-ff]
[    0.236000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci                                  bridge
[    0.248000] ifx_pcie_fixup_resource: fixup host controller 0000:00:00.0 (15d1                                 :0011)
[    0.252000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[    0.256000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff]
[    0.260000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.264000] pci 0000:00:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
[    0.268000] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
[    0.272000] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[    0.276000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[    0.280000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[    0.284000] Switching to clocksource MIPS
[    0.292000] NET: Registered protocol family 2
[    0.296000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.304000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.308000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.316000] TCP: reno registered
[    0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.324000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.332000] NET: Registered protocol family 1
[    5.264000] gptu: totally 6 16-bit timers/counters
[    5.268000] gptu: misc_register on minor 63
[    5.272000] gptu: succeeded to request irq 126
[    5.276000] gptu: succeeded to request irq 127
[    5.280000] gptu: succeeded to request irq 128
[    5.284000] gptu: succeeded to request irq 129
[    5.288000] gptu: succeeded to request irq 130
[    5.296000] gptu: succeeded to request irq 131
[    5.300000] ralink,eeprom ralink_eep.6: using RT3092.eeprom as eeprom
[    5.308000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a1x.bin
[    5.316000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 69E0000
[    5.320000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 69E0000
[    5.428000] Wired TLB entries for Linux read_c0_wired() = 0
[    5.436000] config3 0x2424 MT 1
[    5.436000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[    5.436000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[    5.452000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    5.456000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT                                 Y) (c) 2001-2006 Red Hat, Inc.
[    5.468000] msgmni has been set to 238
[    5.472000] io scheduler noop registered
[    5.476000] io scheduler deadline registered (default)
[    5.484000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lant                                 iq,asc
[    5.492000] console [ttyLTQ0] enabled, bootconsole disabled
[    5.492000] console [ttyLTQ0] enabled, bootconsole disabled
[    5.504000] lantiq nor flash device: 00800000 at 10000000
[    5.508000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer                                  ID 0x0000c2 Chip ID 0x0022cb
[    5.516000] Amd/Fujitsu Extended Query Table at 0x0040
[    5.524000]   Amd/Fujitsu Extended Query version 1.1.
[    5.528000] number of CFI chips: 1
[    5.532000] 4 ofpart partitions found on MTD device ltq_nor
[    5.536000] Creating 4 MTD partitions on "ltq_nor":
[    5.540000] 0x000000000000-0x000000050000 : "uboot"
[    5.548000] 0x000000050000-0x000000060000 : "board_config"
[    5.556000] 0x000000060000-0x000000070000 : "uboot_env"
[    5.560000] 0x000000070000-0x000000800000 : "unused"
[    5.568000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 1                                 28MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[    5.576000] Scanning device for bad blocks
[    5.600000] Bad eraseblock 215 at 0x000001ae0000
[    5.664000] Bad eraseblock 952 at 0x000007700000
[    5.672000] 2 ofpart partitions found on MTD device 14000000.nand-parts
[    5.676000] Creating 2 MTD partitions on "14000000.nand-parts":
[    5.684000] 0x000000000000-0x000000200000 : "kernel"
[    5.692000] 0x000000200000-0x000008000000 : "ubi"
[    5.804000] libphy: lantiq,xrx200-mdio: probed
[    5.812000] net-xrx200: invalid MAC, using random
[    5.816000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00                                 , irq=-1)
[    5.824000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01                                 , irq=-1)
[    5.832000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11                                 , irq=-1)
[    5.840000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13                                 , irq=-1)
[    5.848000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05                                 , irq=-1)
[    5.856000] wdt 1f8803f0.watchdog: Init done
[    5.860000] leds-gpio gpio-leds.8: pins are not configured from the driver
[    5.872000] TCP: cubic registered
[    5.872000] NET: Registered protocol family 17
[    5.876000] 8021q: 802.1Q VLAN Support v1.8
[    5.884000] UBI: auto-attach mtd5
[    5.888000] UBI: attaching mtd5 to ubi0
[    6.072000] UBI: scanning is finished
[    6.088000] UBI: attached mtd5 (name "ubi", size 126 MiB) to ubi0
[    6.092000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    6.100000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    6.104000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    6.112000] UBI: good PEBs: 1006, bad PEBs: 2, corrupted PEBs: 0
[    6.116000] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
[    6.124000] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image seque                                 nce number: 3652312891
[    6.136000] UBI: available PEBs: 984, total reserved PEBs: 22, PEBs reserved                                  for bad PEB h[    6.152000] Freeing unused kernel memory: 3208K (803fe000 - 8072                                 0000)
[    6.160000] UBI: background thread "ubi_bgt0d" started, PID 251
procd: Console is alive
procd: - watchdog -
[    6.232000] SCSI subsystem initialized
[    6.240000] IFXUSB: ifxusb_hcd: version 3.2 B110801
[    6.244000] Chip Version :01c0 BurstSize=0
[    6.848000] IFXUSB: USB core #0 soft-reset
[    7.152000] IFXUSB: USB core #0 soft-reset
[    7.152000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    7.156000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus numbe                                 r 1
[    7.164000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
[    7.172000] IFXUSB: Init: Power Port (0)
[    7.176000] hub 1-0:1.0: USB hub found
[    7.180000] hub 1-0:1.0: 1 port detected
[    7.684000] IFXUSB: USB core #1 soft-reset
[    7.988000] IFXUSB: USB core #1 soft-reset
[    7.988000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
[    7.992000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus numbe                                 r 2
[    8.000000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000
[    8.008000] IFXUSB: Init: Power Port (0)
[    8.012000] hub 2-0:1.0: USB hub found
[    8.016000] hub 2-0:1.0: 1 port detected
[    8.020000] ifxusb_hcd ifxusb_hcd: requested GPIO 233
[    8.028000] usbcore: registered new interface driver usb-storage
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.176000] eth0: port 4 got link
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[   12.592000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH

[   12.616000] NET: Registered protocol family 10
[   12.628000] NET: Registered protocol family 8
[   12.632000] NET: Registered protocol family 20
[   12.644000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   12.660000] PPP generic driver version 2.4.2
[   12.672000] nf_conntrack version 0.5.0 (1962 buckets, 7848 max)
[   12.684000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.700000] MEI CPE Driver, Version 1.2.0

[   12.704000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###


Lantiq CPE API Driver version: DSL CPE API V4.11.4
[   12.728000]
[   12.728000] Predefined debug level: 2
[   12.740000] fuse init (API version 7.22)
[   12.748000] Loading modules backported from Linux version master-2014-05-22-0                                 -gf2032ea
[   12.752000] Backport generated by backports.git backports-20140320-37-g5c33da                                 0
[   12.764000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.776000] Infineon Technologies DEU driver version 2.0.0
[   12.780000] IFX DEU DES initialized (multiblock).
[   12.784000] IFX DEU AES initialized (multiblock).
[   12.792000] IFX DEU ARC4 initialized (multiblock).
[   12.796000] IFX DEU SHA1 initialized.
[   12.800000] IFX DEU MD5 initialized.
[   12.800000] IFX DEU SHA1_HMAC initialized.
[   12.808000] IFX DEU MD5_HMAC initialized.
[   12.828000] NET: Registered protocol family 24
[   12.836000] usbcore: registered new interface driver ums-alauda
[   12.844000] usbcore: registered new interface driver ums-cypress
[   12.852000] usbcore: registered new interface driver ums-datafab
[   12.856000] usbcore: registered new interface driver ums-freecom
[   12.864000] usbcore: registered new interface driver ums-isd200
[   12.872000] usbcore: registered new interface driver ums-jumpshot
[   12.876000] usbcore: registered new interface driver ums-karma
[   12.884000] usbcore: registered new interface driver ums-sddr09
[   12.892000] usbcore: registered new interface driver ums-sddr55
[   12.900000] usbcore: registered new interface driver ums-usbat
[   12.924000] xt_time: kernel timezone is -0000
[   12.952000] cfg80211: Calling CRDA to update world regulatory domain
[   12.956000] cfg80211: World regulatory domain updated:
[   12.960000] cfg80211:  DFS Master region: unset
[   12.964000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gai                                 n, max_eirp), (dfs_cac_time)
[   12.976000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 m                                 Bm), (N/A)
[   12.984000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 m                                 Bm), (N/A)
[   12.992000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 m                                 Bm), (N/A)
[   13.000000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000                                  mBm), (N/A)
[   13.008000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000                                  mBm), (0 s)
[   13.016000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000                                  mBm), (0 s)
[   13.024000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 m                                 Bm), (N/A)
[   13.032000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0                                  mBm), (N/A)
[   13.124000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[   13.128000] rt2800pci 0000:01:00.0: failed to load eeprom property
[   13.136000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEP                                 ROM data from 'RT3092.eeprom'.
[   13.144000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3071, rev 021c d                                 etected
[   13.152000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
[   17.540000] PTM 1.0.27    PTM (E1) firmware version 0.30
[   17.544000] ifxmips_ptm: PTM init succeed
[   19.768000] device eth0.1 entered promiscuous mode
[   19.772000] device eth0 entered promiscuous mode
[   19.776000] br-lan: port 1(eth0.1) entered forwarding state
[   19.784000] br-lan: port 1(eth0.1) entered forwarding state
[   21.788000] br-lan: port 1(eth0.1) entered forwarding state
procd: - init complete -



BusyBox v1.22.1 (2014-12-21 15:15:42 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Barrier Breaker, r43483)
-----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/# passwd
Changing password for root
New password:
Bad password: too weak
Retype password:
Password for root changed by root
root@OpenWrt:/# ubidetach -p /dev/mtd5
[  190.208000] UBI: detaching mtd5 from ubi0
[  190.212000] UBI: mtd5 is detached from ubi0
root@OpenWrt:/# ubiformat /dev/mtd5 -f /tmp/openwrt-lantiq-xrx200-P2812HNUF3-squ
ashfs-ubinized.bin
ubiformat: mtd5 (nand), size 132120576 bytes (126.0 MiB), 1008 eraseblocks of 13                                 1072 bytes (128.0 KiB), min. I/O size 2048 bytes
libscan: scanning eraseblock 1007 -- 100 % complete
ubiformat: 1006 eraseblocks have valid erase counter, mean value is 1
ubiformat: 2 bad eraseblocks found, numbers: 199, 936
ubiformat: flashing eraseblock 0 --  3 % complete  libmtd: error!: MEMERASE64 io                                 ctl failed for eraseblock 0 (mtd5)
        error 5 (Input/output error)

ubiformat: error!: failed to erase eraseblock 0
           error 5 (Input/output error)
ubiformat: mark it as bad? (y/N)


root@OpenWrt:/# ubiformat /dev/mtd5 -f /tmp/openwrt-lantiq-xrx200-P2812HNUF3-squ
ashfs-ubinized.bin
ubiformat: mtd5 (nand), size 132120576 bytes (126.0 MiB), 1008 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
libscan: scanning eraseblock 1007 -- 100 % complete
ubiformat: 1006 eraseblocks have valid erase counter, mean value is 1
ubiformat: 2 bad eraseblocks found, numbers: 199, 936
ubiformat: flashing eraseblock 0 --  3 % complete  libmtd: error!: MEMERASE64 ioctl failed for eraseblock 0 (mtd5)
        error 5 (Input/output error)

ubiformat: error!: failed to erase eraseblock 0
           error 5 (Input/output error)
ubiformat: mark it as bad? (y/N) n
root@OpenWrt:/# restart
/bin/ash: restart: not found
root@OpenWrt:/# reboot
procd: - shutdown -
root@OpenWrt:/# procd: - reboot -[  406.092000] Res

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
P-2812HNU-Fx # etenv nboot ' nand read 0x80800000 0x0 0x200000; bootm 0x80800000'
Unknown command 'etenv' - try 'help'
P-2812HNU-Fx # setenv nboot ' nand read 0x80800000 0x0 0x200000; bootm 0x80800000'
P-2812HNU-Fx # setenv bootcmd 'run nboot'
P-2812HNU-Fx # saveenv
Saving Environment to Flash...
. done
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... done
. done
Protected 1 sectors
P-2812HNU-Fx # reboot
Unknown command 'reboot' - try 'help'
P-2812HNU-Fx # reboot
Unknown command 'reboot' - try 'help'
P-2812HNU-Fx # reset˙

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x0, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Created:      2014-12-21  14:26:39 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1448504 Bytes = 1.4 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.10.49 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43483) ) #1 Sun Dec 21 15:25:34 CET 2014
[    0.000000] SoC: VR9 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019555 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF3 - ZyXEL P-2812HNU-F3
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00047140
[    0.000000] Readback ErrCtl register=00047140
[    0.000000] Memory: 125368k/131072k available (3046k kernel code, 5704k reserved, 1031k data, 200k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.200000] bio: create slab <bio-0> at 0
[    0.204000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.208000] usbcore: registered new interface driver usbfs
[    0.212000] usbcore: registered new interface driver hub
[    0.216000] usbcore: registered new device driver usb
[    0.220000] PCI host bridge to bus 0000:00
[    0.224000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
[    0.228000] pci_bus 0000:00: root bus resource [io  0x1d800000-0x1d8fffff]
[    0.232000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.236000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[    0.248000] ifx_pcie_fixup_resource: fixup host controller 0000:00:00.0 (15d1:0011)
[    0.252000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[    0.256000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff]
[    0.260000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.264000] pci 0000:00:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
[    0.268000] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
[    0.272000] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[    0.276000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[    0.280000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[    0.284000] Switching to clocksource MIPS
[    0.292000] NET: Registered protocol family 2
[    0.296000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.304000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.308000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.316000] TCP: reno registered
[    0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.324000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.332000] NET: Registered protocol family 1
[    0.336000] gptu: totally 6 16-bit timers/counters
[    0.340000] gptu: misc_register on minor 63
[    0.344000] gptu: succeeded to request irq 126
[    0.348000] gptu: succeeded to request irq 127
[    0.352000] gptu: succeeded to request irq 128
[    0.360000] gptu: succeeded to request irq 129
[    0.364000] gptu: succeeded to request irq 130
[    0.368000] gptu: succeeded to request irq 131
[    0.372000] ralink,eeprom ralink_eep.6: using RT3092.eeprom as eeprom
[    0.380000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a1x.bin
[    0.388000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 78C0000
[    0.396000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 78C0000
[    0.500000] Wired TLB entries for Linux read_c0_wired() = 0
[    0.508000] config3 0x2424 MT 1
[    0.508000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[    0.508000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[    0.524000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.532000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.540000] msgmni has been set to 244
[    0.544000] io scheduler noop registered
[    0.548000] io scheduler deadline registered (default)
[    0.556000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[    0.564000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.564000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.576000] lantiq nor flash device: 00800000 at 10000000
[    0.580000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.592000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.596000]   Amd/Fujitsu Extended Query version 1.1.
[    0.600000] number of CFI chips: 1
[    0.604000] 4 ofpart partitions found on MTD device ltq_nor
[    0.608000] Creating 4 MTD partitions on "ltq_nor":
[    0.616000] 0x000000000000-0x000000050000 : "uboot"
[    0.620000] 0x000000050000-0x000000060000 : "board_config"
[    0.628000] 0x000000060000-0x000000070000 : "uboot_env"
[    0.632000] 0x000000070000-0x000000800000 : "unused"
[    0.640000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[    0.648000] Scanning device for bad blocks
[    0.672000] Bad eraseblock 215 at 0x000001ae0000
[    0.736000] Bad eraseblock 952 at 0x000007700000
[    0.744000] 2 ofpart partitions found on MTD device 14000000.nand-parts
[    0.752000] Creating 2 MTD partitions on "14000000.nand-parts":
[    0.756000] 0x000000000000-0x000000200000 : "kernel"
[    0.764000] 0x000000200000-0x000008000000 : "ubi"
[    0.876000] libphy: lantiq,xrx200-mdio: probed
[    0.884000] net-xrx200: invalid MAC, using random
[    0.888000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1)
[    0.896000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1)
[    0.904000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    0.912000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    0.920000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1)
[    0.928000] wdt 1f8803f0.watchdog: Init done
[    0.932000] leds-gpio gpio-leds.8: pins are not configured from the driver
[    0.944000] TCP: cubic registered
[    0.944000] NET: Registered protocol family 17
[    0.948000] 8021q: 802.1Q VLAN Support v1.8
[    0.956000] UBI: auto-attach mtd5
[    0.960000] UBI: attaching mtd5 to ubi0
[    1.148000] UBI: scanning is finished
[    1.160000] UBI: attached mtd5 (name "ubi", size 126 MiB) to ubi0
[    1.164000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.172000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.180000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    1.184000] UBI: good PEBs: 1006, bad PEBs: 2, corrupted PEBs: 0
[    1.192000] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
[    1.196000] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 3652312891
[    1.208000] UBI: available PEBs: 984, total reserved PEBs: 22, PEBs reserved for bad PEB h[    1.216000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    1.224000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.232000] Please append a correct "root=" boot option; here are the available partitions:
[    1.240000] 1f00             320 mtdblock0  (driver?)
[    1.244000] 1f01              64 mtdblock1  (driver?)
[    1.248000] 1f02              64 mtdblock2  (driver?)
[    1.252000] 1f03            7744 mtdblock3  (driver?)
[    1.260000] 1f04            2048 mtdblock4  (driver?)
[    1.264000] 1f05          129024 mtdblock5  (driver?)
[    1.268000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[   65.148000] PCIe RC error intr 161
[   65.1˙

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x0, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Created:      2014-12-21  14:26:39 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1448504 Bytes = 1.4 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.10.49 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43483) ) #1 Sun Dec 21 15:25:34 CET 2014
[    0.000000] SoC: VR9 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019555 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF3 - ZyXEL P-2812HNU-F3
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=0004714a
[    0.000000] Readback ErrCtl register=0004714a
[    0.000000] Memory: 125368k/131072k available (3046k kernel code, 5704k reserved, 1031k data, 200k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.200000] bio: create slab <bio-0> at 0
[    0.204000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.208000] usbcore: registered new interface driver usbfs
[    0.212000] usbcore: registered new interface driver hub
[    0.216000] usbcore: registered new device driver usb
[    0.220000] PCI host bridge to bus 0000:00
[    0.224000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
[    0.228000] pci_bus 0000:00: root bus resource [io  0x1d800000-0x1d8fffff]
[    0.232000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.236000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[    0.248000] ifx_pcie_fixup_resource: fixup host controller 0000:00:00.0 (15d1:0011)
[    0.252000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[    0.256000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff]
[    0.260000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.264000] pci 0000:00:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
[    0.268000] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
[    0.272000] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[    0.276000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[    0.280000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[    0.284000] Switching to clocksource MIPS
[    0.292000] NET: Registered protocol family 2
[    0.296000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.304000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.308000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.316000] TCP: reno registered
[    0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.324000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.332000] NET: Registered protocol family 1
[    0.336000] gptu: totally 6 16-bit timers/counters
[    0.340000] gptu: misc_register on minor 63
[    0.344000] gptu: succeeded to request irq 126
[    0.348000] gptu: succeeded to request irq 127
[    0.352000] gptu: succeeded to request irq 128
[    0.360000] gptu: succeeded to request irq 129
[    0.364000] gptu: succeeded to request irq 130
[    0.368000] gptu: succeeded to request irq 131
[    0.372000] ralink,eeprom ralink_eep.6: using RT3092.eeprom as eeprom
[    0.380000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a1x.bin
[    0.388000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 78C0000
[    0.396000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 78C0000
[    0.500000] Wired TLB entries for Linux read_c0_wired() = 0
[    0.508000] config3 0x2424 MT 1
[    0.508000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[    0.508000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[    0.524000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.532000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.540000] msgmni has been set to 244
[    0.544000] io scheduler noop registered
[    0.548000] io scheduler deadline registered (default)
[    0.556000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[    0.564000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.564000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.576000] lantiq nor flash device: 00800000 at 10000000
[    0.580000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.592000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.596000]   Amd/Fujitsu Extended Query version 1.1.
[    0.600000] number of CFI chips: 1
[    0.604000] 4 ofpart partitions found on MTD device ltq_nor
[    0.608000] Creating 4 MTD partitions on "ltq_nor":
[    0.616000] 0x000000000000-0x000000050000 : "uboot"
[    0.620000] 0x000000050000-0x000000060000 : "board_config"
[    0.628000] 0x000000060000-0x000000070000 : "uboot_env"
[    0.632000] 0x000000070000-0x000000800000 : "unused"
[    0.640000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[    0.648000] Scanning device for bad blocks
[    0.672000] Bad eraseblock 215 at 0x000001ae0000
[    0.736000] Bad eraseblock 952 at 0x000007700000
[    0.744000] 2 ofpart partitions found on MTD device 14000000.nand-parts
[    0.752000] Creating 2 MTD partitions on "14000000.nand-parts":
[    0.756000] 0x000000000000-0x000000200000 : "kernel"
[    0.764000] 0x000000200000-0x000008000000 : "ubi"
[    0.876000] libphy: lantiq,xrx200-mdio: probed
[    0.884000] net-xrx200: invalid MAC, using random
[    0.888000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1)
[    0.896000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1)
[    0.904000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    0.912000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    0.920000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1)
[    0.928000] wdt 1f8803f0.watchdog: Init done
[    0.932000] leds-gpio gpio-leds.8: pins are not configured from the driver
[    0.944000] TCP: cubic registered
[    0.944000] NET: Registered protocol family 17
[    0.948000] 8021q: 802.1Q VLAN Support v1.8
[    0.956000] UBI: auto-attach mtd5
[    0.960000] UBI: attaching mtd5 to ubi0
[    1.144000] UBI: scanning is finished
[    1.160000] UBI: attached mtd5 (name "ubi", size 126 MiB) to ubi0
[    1.164000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.172000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.176000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    1.184000] UBI: good PEBs: 1006, bad PEBs: 2, corrupted PEBs: 0
[    1.192000] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
[    1.196000] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 3652312891
[    1.208000] UBI: available PEBs: 984, total reserved PEBs: 22, PEBs reserved for bad PEB h[    1.216000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    1.224000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.232000] Please append a correct "root=" boot option; here are the available partitions:
[    1.240000] 1f00             320 mtdblock0  (driver?)
[    1.244000] 1f01              64 mtdblock1  (driver?)
[    1.248000] 1f02              64 mtdblock2  (driver?)
[    1.252000] 1f03            7744 mtdblock3  (driver?)
[    1.260000] 1f04            2048 mtdblock4  (driver?)
[    1.264000] 1f05          129024 mtdblock5  (driver?)
[    1.268000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

40

Odp: ZyXEL P-2812HNU czy Netgear 3700?

1. Przecież miałeś działający system, to po co go poprawiałeś?
2. Wgrałeś staroć która pamięta dinozaury. Wgraj aktualne lede.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

41 (edytowany przez m-s-x 2018-03-01 10:27:20)

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Na stronie LEDE znalazłem takie pliki:
lede-17.01.4-lantiq-xrx200-P2812HNUF3-squashfs-sysupgrade.bin
lede-17.01.4-lantiq-xrx200-P2812HNUF3-ubifs-sysupgrade.bin

Wgrałem jeszcze raz i to samo
BusyBox v1.22.1 (2014-12-21 15:15:42 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Barrier Breaker, r43483)
-----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/# passwd
Changing password for root
New password:
Bad password: too weak
Retype password:
Password for root changed by root
root@OpenWrt:/# ubidetach -p /dev/mtd5
[   97.580000] UBI: detaching mtd5 from ubi0
[   97.584000] UBI: mtd5 is detached from ubi0
root@OpenWrt:/# ubiformat /dev/mtd5 -f /tmp/lede-17.01.4-lantiq-xrx200-P2812HNUF
3-squashfs-sysupgrade.bin
ubiformat: mtd5 (nand), size 132120576 bytes (126.0 MiB), 1008 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
libscan: scanning eraseblock 1007 -- 100 % complete
ubiformat: 1006 eraseblocks have valid erase counter, mean value is 1
ubiformat: 2 bad eraseblocks found, numbers: 199, 936
ubiformat: error!: file "/tmp/lede-17.01.4-lantiq-xrx200-P2812HNUF3-squashfs-sysupgrade.bin" (size 4833448 bytes) is not multiple of eraseblock size (131072 bytes)
           error 0 (Success)
root@OpenWrt:/# reboot
procd: - shutdown -
root@OpenWrt:/# procd: - reboot -[  169.728000] Resô

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
P-2812HNU-Fx # setenv nboot ' nand read 0x80800000 0x0 0x200000; bootm 0x80800000'
P-2812HNU-Fx # setenv bootcmd 'run nboot'
P-2812HNU-Fx # saveenv
Saving Environment to Flash...
. done
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... done
. done
Protected 1 sectors
P-2812HNU-Fx # reboot
Unknown command 'reboot' - try 'help'
P-2812HNU-Fx #

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x0, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Created:      2014-12-21  14:26:39 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1448504 Bytes = 1.4 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.10.49 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43483) ) #1 Sun Dec 21 15:25:34 CET 2014
[    0.000000] SoC: VR9 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019555 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF3 - ZyXEL P-2812HNU-F3
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00047148
[    0.000000] Readback ErrCtl register=00047148
[    0.000000] Memory: 125368k/131072k available (3046k kernel code, 5704k reserved, 1031k data, 200k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.200000] bio: create slab <bio-0> at 0
[    0.204000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.208000] usbcore: registered new interface driver usbfs
[    0.212000] usbcore: registered new interface driver hub
[    0.216000] usbcore: registered new device driver usb
[    0.220000] PCI host bridge to bus 0000:00
[    0.224000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
[    0.228000] pci_bus 0000:00: root bus resource [io  0x1d800000-0x1d8fffff]
[    0.232000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.236000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[    0.248000] ifx_pcie_fixup_resource: fixup host controller 0000:00:00.0 (15d1:0011)
[    0.252000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[    0.256000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff]
[    0.260000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.264000] pci 0000:00:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
[    0.268000] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
[    0.272000] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[    0.276000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[    0.280000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[    0.284000] Switching to clocksource MIPS
[    0.292000] NET: Registered protocol family 2
[    0.296000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.304000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.308000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.316000] TCP: reno registered
[    0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.324000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.332000] NET: Registered protocol family 1
[    0.336000] gptu: totally 6 16-bit timers/counters
[    0.340000] gptu: misc_register on minor 63
[    0.344000] gptu: succeeded to request irq 126
[    0.348000] gptu: succeeded to request irq 127
[    0.352000] gptu: succeeded to request irq 128
[    0.360000] gptu: succeeded to request irq 129
[    0.364000] gptu: succeeded to request irq 130
[    0.368000] gptu: succeeded to request irq 131
[    0.372000] ralink,eeprom ralink_eep.6: using RT3092.eeprom as eeprom
[    0.380000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a1x.bin
[    0.388000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 78C0000
[    0.396000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 78C0000
[    0.500000] Wired TLB entries for Linux read_c0_wired() = 0
[    0.508000] config3 0x2424 MT 1
[    0.508000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[    0.508000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[    0.524000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.532000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.540000] msgmni has been set to 244
[    0.544000] io scheduler noop registered
[    0.548000] io scheduler deadline registered (default)
[    0.556000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[    0.564000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.564000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.576000] lantiq nor flash device: 00800000 at 10000000
[    0.580000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.592000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.596000]   Amd/Fujitsu Extended Query version 1.1.
[    0.600000] number of CFI chips: 1
[    0.604000] 4 ofpart partitions found on MTD device ltq_nor
[    0.608000] Creating 4 MTD partitions on "ltq_nor":
[    0.616000] 0x000000000000-0x000000050000 : "uboot"
[    0.620000] 0x000000050000-0x000000060000 : "board_config"
[    0.628000] 0x000000060000-0x000000070000 : "uboot_env"
[    0.632000] 0x000000070000-0x000000800000 : "unused"
[    0.640000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[    0.648000] Scanning device for bad blocks
[    0.672000] Bad eraseblock 215 at 0x000001ae0000
[    0.736000] Bad eraseblock 952 at 0x000007700000
[    0.744000] 2 ofpart partitions found on MTD device 14000000.nand-parts
[    0.752000] Creating 2 MTD partitions on "14000000.nand-parts":
[    0.756000] 0x000000000000-0x000000200000 : "kernel"
[    0.764000] 0x000000200000-0x000008000000 : "ubi"
[    0.876000] libphy: lantiq,xrx200-mdio: probed
[    0.884000] net-xrx200: invalid MAC, using random
[    0.888000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1)
[    0.896000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1)
[    0.904000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    0.912000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    0.920000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1)
[    0.928000] wdt 1f8803f0.watchdog: Init done
[    0.932000] leds-gpio gpio-leds.8: pins are not configured from the driver
[    0.944000] TCP: cubic registered
[    0.944000] NET: Registered protocol family 17
[    0.948000] 8021q: 802.1Q VLAN Support v1.8
[    0.956000] UBI: auto-attach mtd5
[    0.960000] UBI: attaching mtd5 to ubi0
[    1.144000] UBI: scanning is finished
[    1.160000] UBI: attached mtd5 (name "ubi", size 126 MiB) to ubi0
[    1.164000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.172000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.176000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    1.184000] UBI: good PEBs: 1006, bad PEBs: 2, corrupted PEBs: 0
[    1.192000] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
[    1.196000] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 3652312891
[    1.208000] UBI: available PEBs: 984, total reserved PEBs: 22, PEBs reserved for bad PEB h[    1.216000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    1.224000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.232000] Please append a correct "root=" boot option; here are the available partitions:
[    1.240000] 1f00             320 mtdblock0  (driver?)
[    1.244000] 1f01              64 mtdblock1  (driver?)
[    1.248000] 1f02              64 mtdblock2  (driver?)
[    1.252000] 1f03            7744 mtdblock3  (driver?)
[    1.260000] 1f04            2048 mtdblock4  (driver?)
[    1.264000] 1f05          129024 mtdblock5  (driver?)
[    1.268000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[   82.172000] PCIe RC error intr 161
[   82.1˙

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x0, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Created:      2014-12-21  14:26:39 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1448504 Bytes = 1.4 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 3.10.49 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43483) ) #1 Sun Dec 21 15:25:34 CET 2014
[    0.000000] SoC: VR9 rev 1.1
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019555 (MIPS 34Kc)
[    0.000000] MIPS: machine is P2812HNUF3 - ZyXEL P-2812HNU-F3
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00047140
[    0.000000] Readback ErrCtl register=00047140
[    0.000000] Memory: 125368k/131072k available (3046k kernel code, 5704k reserved, 1031k data, 200k init, 0k highmem)
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.032000] pid_max: default: 32768 minimum: 301
[    0.036000] Mount-cache hash table entries: 512
[    0.040000] pinctrl core: initialized pinctrl subsystem
[    0.044000] NET: Registered protocol family 16
[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185]
[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193]
[    0.200000] bio: create slab <bio-0> at 0
[    0.204000] gpio-stp-xway 1e100bb0.stp: Init done
[    0.208000] usbcore: registered new interface driver usbfs
[    0.212000] usbcore: registered new interface driver hub
[    0.216000] usbcore: registered new device driver usb
[    0.220000] PCI host bridge to bus 0000:00
[    0.224000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
[    0.228000] pci_bus 0000:00: root bus resource [io  0x1d800000-0x1d8fffff]
[    0.232000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.236000] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[    0.248000] ifx_pcie_fixup_resource: fixup host controller 0000:00:00.0 (15d1:0011)
[    0.252000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[    0.256000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff]
[    0.260000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.264000] pci 0000:00:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
[    0.268000] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1
[    0.272000] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[    0.276000] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[    0.280000] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[    0.284000] Switching to clocksource MIPS
[    0.292000] NET: Registered protocol family 2
[    0.296000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.304000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.308000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.316000] TCP: reno registered
[    0.320000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.324000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.332000] NET: Registered protocol family 1
[    0.336000] gptu: totally 6 16-bit timers/counters
[    0.340000] gptu: misc_register on minor 63
[    0.344000] gptu: succeeded to request irq 126
[    0.348000] gptu: succeeded to request irq 127
[    0.352000] gptu: succeeded to request irq 128
[    0.360000] gptu: succeeded to request irq 129
[    0.364000] gptu: succeeded to request irq 130
[    0.368000] gptu: succeeded to request irq 131
[    0.372000] ralink,eeprom ralink_eep.6: using RT3092.eeprom as eeprom
[    0.380000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a1x.bin
[    0.388000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 78C0000
[    0.396000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 78C0000
[    0.500000] Wired TLB entries for Linux read_c0_wired() = 0
[    0.508000] config3 0x2424 MT 1
[    0.508000] MVPControl 0x2, STLB 0 VPC 1 EVP 0
[    0.508000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1
[    0.524000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.532000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.540000] msgmni has been set to 244
[    0.544000] io scheduler noop registered
[    0.548000] io scheduler deadline registered (default)
[    0.556000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[    0.564000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.564000] console [ttyLTQ0] enabled, bootconsole disabled
[    0.576000] lantiq nor flash device: 00800000 at 10000000
[    0.580000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.592000] Amd/Fujitsu Extended Query Table at 0x0040
[    0.596000]   Amd/Fujitsu Extended Query version 1.1.
[    0.600000] number of CFI chips: 1
[    0.604000] 4 ofpart partitions found on MTD device ltq_nor
[    0.608000] Creating 4 MTD partitions on "ltq_nor":
[    0.616000] 0x000000000000-0x000000050000 : "uboot"
[    0.620000] 0x000000050000-0x000000060000 : "board_config"
[    0.628000] 0x000000060000-0x000000070000 : "uboot_env"
[    0.632000] 0x000000070000-0x000000800000 : "unused"
[    0.640000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[    0.648000] Scanning device for bad blocks
[    0.672000] Bad eraseblock 215 at 0x000001ae0000
[    0.736000] Bad eraseblock 952 at 0x000007700000
[    0.744000] 2 ofpart partitions found on MTD device 14000000.nand-parts
[    0.752000] Creating 2 MTD partitions on "14000000.nand-parts":
[    0.756000] 0x000000000000-0x000000200000 : "kernel"
[    0.764000] 0x000000200000-0x000008000000 : "ubi"
[    0.876000] libphy: lantiq,xrx200-mdio: probed
[    0.884000] net-xrx200: invalid MAC, using random
[    0.888000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1)
[    0.896000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1)
[    0.904000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    0.912000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    0.920000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1)
[    0.928000] wdt 1f8803f0.watchdog: Init done
[    0.932000] leds-gpio gpio-leds.8: pins are not configured from the driver
[    0.944000] TCP: cubic registered
[    0.944000] NET: Registered protocol family 17
[    0.948000] 8021q: 802.1Q VLAN Support v1.8
[    0.956000] UBI: auto-attach mtd5
[    0.960000] UBI: attaching mtd5 to ubi0
[    1.144000] UBI: scanning is finished
[    1.160000] UBI: attached mtd5 (name "ubi", size 126 MiB) to ubi0
[    1.164000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.172000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.176000] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    1.184000] UBI: good PEBs: 1006, bad PEBs: 2, corrupted PEBs: 0
[    1.192000] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
[    1.196000] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 3652312891
[    1.208000] UBI: available PEBs: 984, total reserved PEBs: 22, PEBs reserved for bad PEB h[    1.216000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    1.224000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.232000] Please append a correct "root=" boot option; here are the available partitions:
[    1.240000] 1f00             320 mtdblock0  (driver?)
[    1.244000] 1f01              64 mtdblock1  (driver?)
[    1.248000] 1f02              64 mtdblock2  (driver?)
[    1.252000] 1f03            7744 mtdblock3  (driver?)
[    1.260000] 1f04            2048 mtdblock4  (driver?)
[    1.264000] 1f05          129024 mtdblock5  (driver?)
[    1.268000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

42

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Jeszcze raz: wgraj aktualny obraz.

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

43

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Wgrałem obraz z Twojej strony:
openwrt-15.05-lantiq-xrx200-P2812HNUF3-uImage i
openwrt-15.05-lantiq-xrx200-P2812HNUF3-uImage-initramfs i

P-2812HNU-Fx # bootm 0x80800000
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.45
   Created:      2017-06-03   4:48:37 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4537051 Bytes = 4.3 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA: uncompress or overwrite error 7 - must RESET b

U-Boot 2014.01-openwrt2 (Nov 15 2014 - 14:05:27) P-2812HNU-Fx

Board: ZyXEL P-2812HNU-Fx
SoC:   Lantiq VRX288 v1.1
CPU:   500 MHz
IO:    250 MHz
BUS:   250 MHz
BOOT:  NOR w/o BootROM
DRAM:  128 MiB
Flash: 8 MiB
NAND:  128 MiB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
P-2812HNU-Fx #

44

Odp: ZyXEL P-2812HNU czy Netgear 3700?

To też nie jest najnowsze. Na dodatek - jak wgrałeś oba na raz?

Masz niepotrzebny router, uszkodzony czy nie - chętnie przygarnę go.

45 (edytowany przez m-s-x 2018-03-01 12:13:08)

Odp: ZyXEL P-2812HNU czy Netgear 3700?

nie naraz, po kolei wg opisu:
http://eko.one.pl/forum/viewtopic.php?id=11629

Dlaczego po komendzie: nand erase.chip zamiast :
NAND erase.chip: device 0 whole chip
Skipping bad block at  0x00a00000
Skipping bad block at  0x02700000
Skipping bad block at  0x03e40000
Skipping bad block at  0x05ce0000
Erasing at 0x7fe0000 -- 100% complete.
OK

wyskakuje
nand0: MTD Erase failure: -5
nand0: MTD Erase failure: -5

czyżby NAND był uszkodzony ?

46

Odp: ZyXEL P-2812HNU czy Netgear 3700?

procedura wgrywania :

U-Boot recovery/stock NOR upload for P-2812HNU-F3

Step 1: Place openwrt-lantiq-xrx200-P2812HNUF3-*** images in tftp folder

Step 2: Set Your IP addres to "192.168.1.2" and start tftp server

Step 3: Upload kernel image 
    tftp 0x80800000 openwrt-lantiq-xrx200-P2812HNUF3-uImage

Step 4: Erease NAND 
    nand erase.chip

Step 5: Flash kernel image onto NAND 
    nand write 0x80800000 0x0 0x200000

Step 6: Upload initramfs image
    tftpboot 0x80800000 openwrt-lantiq-xrx200-P2812HNUF3-uImage-initramfs

Step 7: Run initramfs image and wait till fully booted
    bootm 0x80800000

Step 8: Upload UBI image to /tmp in Your router by SCP/WinSCP after setting root passwd on OpenWRT

Step 9: Format and Flash UBI image    # tutaj mozna sprawdzic czy mtd5 czy mtd4   = cat/proc/mount  chyba
     ubidetach -p /dev/mtd5
      ubiformat /dev/mtd5 -f /tmp/openwrt-lantiq-xrx200-P2812HNUF3-squashfs-ubinized.bin (default config RO, changes can be reverted)
     or
     ubiformat /dev/mtd5 -f /tmp/openwrt-lantiq-xrx200-P2812HNUF3-ubifs-ubinized.bin (all data R/W, option to revert changes by reflash)

Step 10: Reboot router

Step 11: Stop U-boot auto boot process and modify to auto boot OpenWRT at power on
    setenv nboot ' nand read 0x80800000 0x0 0x200000; bootm 0x80800000'
    setenv bootcmd 'run nboot'
    saveenv

Step 12: Power off and on router

tylko w pkt.9 masz do wyboru jaki obraz wgrać  bo są dwa do wyboru  - wszystko jest w pliku który zapewne pobrałeś

i jeszcze jedno   

In:    serial
Out:   serial
Err:   serial
Net:   ltq-eth
Hit any key to stop autoboot:  0
Wrong Image Format for bootm command
ERROR: can't get kernel image!
P-2812HNU-Fx # tftp 0x80800000 openwrt-lantiq-xrx200-P2812HNUF3-uImage
ltq_phy: addr 0, link 0, speed 10, duplex 0
ltq_phy: addr 1, link 0, speed 10, duplex 0
ltq_phy: addr 17, link 0, speed 10, duplex 0
ltq_phy: addr 19, link 1, speed 1000, duplex 1
ltq_phy: addr 5, link 0, speed 10, duplex 0

tu masz błąd 
ERROR: can't get kernel image!

47

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Zlaczylem te dwa punkty
Podlaczylem UART i wyskakuje mi jakies dziwne litery/znaki przy bootowaniu
VCC nie jest podpiete
Tx - Zielony
Rx - Bialy
PUSTE
GND - Czarny

Ustawienia w managerze urzadzen jak i w programie Tera Term
115200
8bit
none
1bit
none

48

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Też tak miałem
Jak wymieniłem konwenter ttl wgrało się od razu.

49 (edytowany przez Dabman 2018-12-10 23:25:22)

Odp: ZyXEL P-2812HNU czy Netgear 3700?

EDIT: poszlo

Problem jest taki ze z 3 routerow jakie posiadam, udalo sie przerobic tylko jeden. na 2 pozostalych wyskakuja "znaczki" w Tera Term.
Wszystkie 3 identyczne...

Istnieja alternatywne punkty? czuje ze w jednym przepalilem juz sciezki lutujac X razy

50

Odp: ZyXEL P-2812HNU czy Netgear 3700?

Może mi podpowiecie co robię źle.
Mam F3, zwarłem R24 i R15, mam Tera Term, ustawienia COM jak trzeba, uruchamiam router i widzę:
ROM VER: 1.0.5
UART04
i co ileś wystąpień powyższego mam:
ROM VER: 1.0.5
CFG04
W oknie Tera Term wciąż mi to się pojawia("lata") i nie może się zatrzymać.